harald@xxxxxxxxx schrieb am 30.06.2015 um 21:37:
> On Mon, 29 Jun 2015 21:37:22 +0200, Hartmut Knaack <knaack.h@xxxxxx>
> wrote:
>> Harald Geyer schrieb am 29.06.2015 um 20:59:
>>> Hi Jonathan!
>>>
>>> Jonathan Cameron writes:
> [...]
>>>> Looks good to me. Will wait for comments on the first patch though
>>>> before taking this... clearly that one will need a few acks if I take
>>>> it through IIO!
>>>
>>> The first patch has been merged via tip tree for 4.2 (is already
>>> available
>>> in staging-next tree). Are you going to pick up this patch or do I need
>>> to resend?
>>>
>>> Thanks,
>>> Harald
>>>
>>
>> Hi Harald,
>> there are a few small style issues, which checkpatch.pl --strict should
>> show you.
>
> Thanks for pointing out --strict - didn't know about that yet.
>
> I get the following output:
>
> CHECK: spaces preferred around that '*' (ctx:VxV)
> #96: FILE: drivers/iio/humidity/dht11.c:167:
> + if (DHT11_DATA_BIT_HIGH < 2*timeres) {
> ^
>
> With this one I disagree. Omitting the spaces makes the code easier to
> read, because it reflects the relative binding power of operators involed.
> This style (omitting spaces around * if there is a +, <, etc in the same
> experession) is used throughout the driver. I'd change this only if there
> is consensus, that this really is the preferred way.
I would prefer to make use of parenthesis to reflect a precedence instead
of violating coding style guidelines.
Honestly, it didn't come to my mind that you left out those spaces on
purpose.
>
> CHECK: Alignment should match open parenthesis
> #98: FILE: drivers/iio/humidity/dht11.c:169:
> + dev_err(dht11->dev, "timeresolution %dns too
> low\n",
> + timeres);
>
> Ok, I'll post a patch that updates the driver to this style and update the
> above patch acordingly.
>
> Thanks,
> Harald
>
>
>> Thanks,
>> Hartmut
>>
>>>> Jonathan
>>>>> ---
>>>>> changes since V1:
>>>>> call ktime_get_xxx() functions directly instead of using the wrappers
>>>>> of the iio subsystem.
>>>>>
>>>>> drivers/iio/humidity/dht11.c | 42
>>>>> ++++++++++++++++++++++--------------------
>>>>> 1 files changed, 22 insertions(+), 20 deletions(-)
>>>>>
>>>>> diff --git a/drivers/iio/humidity/dht11.c
>>>>> b/drivers/iio/humidity/dht11.c
>>>>> index 7d79a1a..4cb25dc 100644
>>>>> --- a/drivers/iio/humidity/dht11.c
>>>>> +++ b/drivers/iio/humidity/dht11.c
>>>>> @@ -33,6 +33,7 @@
>>>>> #include <linux/delay.h>
>>>>> #include <linux/gpio.h>
>>>>> #include <linux/of_gpio.h>
>>>>> +#include <linux/timekeeping.h>
>>>>>
>>>>> #include <linux/iio/iio.h>
>>>>>
>>>>> @@ -87,23 +88,11 @@ static unsigned char dht11_decode_byte(int
>>>>> *timing, int threshold)
>>>>> return ret;
>>>>> }
>>>>>
>>>>> -static int dht11_decode(struct dht11 *dht11, int offset)
>>>>> +static int dht11_decode(struct dht11 *dht11, int offset, int
> timeres)
>>>>> {
>>>>> - int i, t, timing[DHT11_BITS_PER_READ], threshold,
>>>>> - timeres = DHT11_SENSOR_RESPONSE;
>>>>> + int i, t, timing[DHT11_BITS_PER_READ], threshold;
>>>>> unsigned char temp_int, temp_dec, hum_int, hum_dec, checksum;
>>>>>
>>>>> - /* Calculate timestamp resolution */
>>>>> - for (i = 1; i < dht11->num_edges; ++i) {
>>>>> - t = dht11->edges[i].ts - dht11->edges[i-1].ts;
>>>>> - if (t > 0 && t < timeres)
>>>>> - timeres = t;
>>>>> - }
>>>>> - if (2*timeres > DHT11_DATA_BIT_HIGH) {
>>>>> - pr_err("dht11: timeresolution %d too bad for decoding\n",
>>>>> - timeres);
>>>>> - return -EIO;
>>>>> - }
>>>>> threshold = DHT11_DATA_BIT_HIGH / timeres;
>>>>> if (DHT11_DATA_BIT_LOW/timeres + 1 >= threshold)
>>>>> pr_err("dht11: WARNING: decoding ambiguous\n");
>>>>> @@ -126,7 +115,7 @@ static int dht11_decode(struct dht11 *dht11, int
>>>>> offset)
>>>>> if (((hum_int + hum_dec + temp_int + temp_dec) & 0xff) != checksum)
>>>>> return -EIO;
>>>>>
>>>>> - dht11->timestamp = iio_get_time_ns();
>>>>> + dht11->timestamp = ktime_get_real_ns();
>>>>> if (hum_int < 20) { /* DHT22 */
>>>>> dht11->temperature = (((temp_int & 0x7f) << 8) + temp_dec) *
>>>>> ((temp_int & 0x80) ? -100 : 100);
>>>>> @@ -154,7 +143,7 @@ static irqreturn_t dht11_handle_irq(int irq, void
>>>>> *data)
>>>>>
>>>>> /* TODO: Consider making the handler safe for IRQ sharing */
>>>>> if (dht11->num_edges < DHT11_EDGES_PER_READ && dht11->num_edges >=
>>>>> 0) {
>>>>> - dht11->edges[dht11->num_edges].ts = iio_get_time_ns();
>>>>> + dht11->edges[dht11->num_edges].ts = ktime_get_real_ns();
>>>>> dht11->edges[dht11->num_edges++].value =
>>>>> gpio_get_value(dht11->gpio);
>>>>>
>>>>> @@ -170,10 +159,22 @@ static int dht11_read_raw(struct iio_dev
>>>>> *iio_dev,
>>>>> int *val, int *val2, long m)
>>>>> {
>>>>> struct dht11 *dht11 = iio_priv(iio_dev);
>>>>> - int ret;
>>>>> + int ret, timeres;
>>>>>
>>>>> mutex_lock(&dht11->lock);
>>>>> - if (dht11->timestamp + DHT11_DATA_VALID_TIME < iio_get_time_ns()) {
>>>>> + if (dht11->timestamp + DHT11_DATA_VALID_TIME < ktime_get_real_ns())
> {
>>>>> + timeres = ktime_get_resolution_ns();
>>>>> + if (DHT11_DATA_BIT_HIGH < 2*timeres) {
>>>>> + dev_err(dht11->dev, "timeresolution %dns too low\n",
>>>>> + timeres);
>>>>> + /* In theory a better clock could become available
>>>>> + * at some point ... and there is no error code
>>>>> + * that really fits better.
>>>>> + */
>>>>> + ret = -EAGAIN;
>>>>> + goto err;
>>>>> + }
>>>>> +
>>>>> reinit_completion(&dht11->completion);
>>>>>
>>>>> dht11->num_edges = 0;
>>>>> @@ -208,7 +209,8 @@ static int dht11_read_raw(struct iio_dev
> *iio_dev,
>>>>> ret = dht11_decode(dht11,
>>>>> dht11->num_edges == DHT11_EDGES_PER_READ ?
>>>>> DHT11_EDGES_PREAMBLE :
>>>>> - DHT11_EDGES_PREAMBLE - 2);
>>>>> + DHT11_EDGES_PREAMBLE - 2,
>>>>> + timeres);
>>>>> if (ret)
>>>>> goto err;
>>>>> }
>>>>> @@ -274,7 +276,7 @@ static int dht11_probe(struct platform_device
>>>>> *pdev)
>>>>> return -EINVAL;
>>>>> }
>>>>>
>>>>> - dht11->timestamp = iio_get_time_ns() - DHT11_DATA_VALID_TIME - 1;
>>>>> + dht11->timestamp = ktime_get_real_ns() - DHT11_DATA_VALID_TIME - 1;
>>>>> dht11->num_edges = -1;
>>>>>
>>>>> platform_set_drvdata(pdev, iio);
>>>>>
>>>>
>>> --
>>> To unsubscribe from this list: send the line "unsubscribe linux-iio" in
>>> the body of a message to majordomo@xxxxxxxxxxxxxxx
>>> More majordomo info at http://vger.kernel.org/majordomo-info.html
>>>
> --
> To unsubscribe from this list: send the line "unsubscribe linux-iio" in
> the body of a message to majordomo@xxxxxxxxxxxxxxx
> More majordomo info at http://vger.kernel.org/majordomo-info.html
>
--
To unsubscribe from this list: send the line "unsubscribe linux-iio" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
