On 04/05/15 10:06, Antoine Tenart wrote:
> This patch adds the support of the Berlin ADC, available on Berlin SoCs.
> This ADC has 8 channels available, with one connected to a temperature
> sensor.1
>
> The particularity here, is that the temperature sensor connected to the
> ADC has its own registers, and both the ADC and the temperature sensor
> must be configured when using it.
>
> Signed-off-by: Antoine Tenart <antoine.tenart@xxxxxxxxxxxxxxxxxx>
Just a couple more little bits and pieces. Main one is a query about whether
the units of the processed output are in milli celsius as the ABI specifies
or Celsius as the comment suggests.
Also, I'm travelling and without internet so can't look it up directly.
So.. On the basis I'll forget to check later.. What is the status
of the two series you say this is based upon?
There are also some overly long lines where spitting them would not
significantly hurt readability so clean those up as well to avoid
the inevitable code style fix patch from someone with too much time on
their hands!
Jonathan
> ---
> drivers/iio/adc/Kconfig | 7 +
> drivers/iio/adc/Makefile | 1 +
> drivers/iio/adc/berlin2-adc.c | 381 ++++++++++++++++++++++++++++++++++++++++++
> 3 files changed, 389 insertions(+)
> create mode 100644 drivers/iio/adc/berlin2-adc.c
>
> diff --git a/drivers/iio/adc/Kconfig b/drivers/iio/adc/Kconfig
> index e36a73e7c3a8..cee50de76fb1 100644
> --- a/drivers/iio/adc/Kconfig
> +++ b/drivers/iio/adc/Kconfig
> @@ -135,6 +135,13 @@ config AXP288_ADC
> device. Depending on platform configuration, this general purpose ADC can
> be used for sampling sensors such as thermal resistors.
>
> +config BERLIN2_ADC
> + tristate "Marvell Berlin2 ADC driver"
> + depends on ARCH_BERLIN
> + help
> + Marvell Berlin2 ADC driver. This ADC has 8 channels, with one used for
> + temperature measurement.
> +
> config DA9150_GPADC
> tristate "Dialog DA9150 GPADC driver support"
> depends on MFD_DA9150
> diff --git a/drivers/iio/adc/Makefile b/drivers/iio/adc/Makefile
> index 3930e63e84bc..a0962103e866 100644
> --- a/drivers/iio/adc/Makefile
> +++ b/drivers/iio/adc/Makefile
> @@ -15,6 +15,7 @@ obj-$(CONFIG_AD7887) += ad7887.o
> obj-$(CONFIG_AD799X) += ad799x.o
> obj-$(CONFIG_AT91_ADC) += at91_adc.o
> obj-$(CONFIG_AXP288_ADC) += axp288_adc.o
> +obj-$(CONFIG_BERLIN2_ADC) += berlin2-adc.o
> obj-$(CONFIG_DA9150_GPADC) += da9150-gpadc.o
> obj-$(CONFIG_CC10001_ADC) += cc10001_adc.o
> obj-$(CONFIG_EXYNOS_ADC) += exynos_adc.o
> diff --git a/drivers/iio/adc/berlin2-adc.c b/drivers/iio/adc/berlin2-adc.c
> new file mode 100644
> index 000000000000..0adfef035d79
> --- /dev/null
> +++ b/drivers/iio/adc/berlin2-adc.c
> @@ -0,0 +1,381 @@
> +/*
> + * Marvell Berlin2 ADC driver
> + *
> + * Copyright (C) 2015 Marvell Technology Group Ltd.
> + *
> + * Antoine Tenart <antoine.tenart@xxxxxxxxxxxxxxxxxx>
> + *
> + * This file is licensed under the terms of the GNU General Public
> + * License version 2. This program is licensed "as is" without any
> + * warranty of any kind, whether express or implied.
> + */
> +
> +#include <linux/iio/iio.h>
> +#include <linux/iio/driver.h>
> +#include <linux/iio/machine.h>
> +#include <linux/interrupt.h>
> +#include <linux/kernel.h>
> +#include <linux/module.h>
> +#include <linux/platform_device.h>
> +#include <linux/slab.h>
> +#include <linux/mfd/syscon.h>
> +#include <linux/regmap.h>
> +#include <linux/sched.h>
> +#include <linux/wait.h>
> +
> +#define BERLIN2_SM_CTRL 0x14
> +#define BERLIN2_SM_CTRL_SM_SOC_INT BIT(1)
> +#define BERLIN2_SM_CTRL_SOC_SM_INT BIT(2)
> +#define BERLIN2_SM_CTRL_ADC_SEL(x) (BIT(x) << 5) /* 0-15 */
> +#define BERLIN2_SM_CTRL_ADC_SEL_MASK (0xf << 5)
> +#define BERLIN2_SM_CTRL_ADC_POWER BIT(9)
> +#define BERLIN2_SM_CTRL_ADC_CLKSEL_DIV2 (0x0 << 10)
> +#define BERLIN2_SM_CTRL_ADC_CLKSEL_DIV3 (0x1 << 10)
> +#define BERLIN2_SM_CTRL_ADC_CLKSEL_DIV4 (0x2 << 10)
> +#define BERLIN2_SM_CTRL_ADC_CLKSEL_DIV8 (0x3 << 10)
> +#define BERLIN2_SM_CTRL_ADC_CLKSEL_MASK (0x3 << 10)
> +#define BERLIN2_SM_CTRL_ADC_START BIT(12)
> +#define BERLIN2_SM_CTRL_ADC_RESET BIT(13)
> +#define BERLIN2_SM_CTRL_ADC_BANDGAP_RDY BIT(14)
> +#define BERLIN2_SM_CTRL_ADC_CONT_SINGLE (0x0 << 15)
> +#define BERLIN2_SM_CTRL_ADC_CONT_CONTINUOUS (0x1 << 15)
> +#define BERLIN2_SM_CTRL_ADC_BUFFER_EN BIT(16)
> +#define BERLIN2_SM_CTRL_ADC_VREF_EXT (0x0 << 17)
> +#define BERLIN2_SM_CTRL_ADC_VREF_INT (0x1 << 17)
> +#define BERLIN2_SM_CTRL_ADC_ROTATE BIT(19)
> +#define BERLIN2_SM_CTRL_TSEN_EN BIT(20)
> +#define BERLIN2_SM_CTRL_TSEN_CLK_SEL_125 (0x0 << 21) /* 1.25 MHz */
> +#define BERLIN2_SM_CTRL_TSEN_CLK_SEL_250 (0x1 << 21) /* 2.5 MHz */
> +#define BERLIN2_SM_CTRL_TSEN_MODE_0_125 (0x0 << 22) /* 0-125 C */
> +#define BERLIN2_SM_CTRL_TSEN_MODE_10_50 (0x1 << 22) /* 10-50 C */
> +#define BERLIN2_SM_CTRL_TSEN_RESET BIT(29)
> +#define BERLIN2_SM_ADC_DATA 0x20
> +#define BERLIN2_SM_ADC_MASK 0x3ff
> +#define BERLIN2_SM_ADC_STATUS 0x1c
> +#define BERLIN2_SM_ADC_STATUS_DATA_RDY(x) BIT(x) /* 0-15 */
> +#define BERLIN2_SM_ADC_STATUS_DATA_RDY_MASK 0xf
> +#define BERLIN2_SM_ADC_STATUS_INT_EN(x) (BIT(x) << 16) /* 0-15 */
> +#define BERLIN2_SM_ADC_STATUS_INT_EN_MASK (0xf << 16)
> +#define BERLIN2_SM_TSEN_STATUS 0x24
> +#define BERLIN2_SM_TSEN_STATUS_DATA_RDY BIT(0)
> +#define BERLIN2_SM_TSEN_STATUS_INT_EN BIT(1)
> +#define BERLIN2_SM_TSEN_DATA 0x28
> +#define BERLIN2_SM_TSEN_MASK 0xfff
> +#define BERLIN2_SM_TSEN_CTRL 0x74
> +#define BERLIN2_SM_TSEN_CTRL_START BIT(8)
> +#define BERLIN2_SM_TSEN_CTRL_SETTLING_4 (0x0 << 21) /* 4 us */
> +#define BERLIN2_SM_TSEN_CTRL_SETTLING_12 (0x1 << 21) /* 12 us */
> +#define BERLIN2_SM_TSEN_CTRL_SETTLING_MASK (0x1 << 21)
> +#define BERLIN2_SM_TSEN_CTRL_TRIM(x) ((x) << 22)
> +#define BERLIN2_SM_TSEN_CTRL_TRIM_MASK (0xf << 22)
> +
> +struct berlin2_adc_priv {
> + struct regmap *regmap;
> + struct mutex lock;
> + wait_queue_head_t wq;
> + int irq;
> + int tsen_irq;
tsen_irq and irq are only used in one function I think. If so just use local
variables rather than cluttering up this structure.
> + bool data_available;
> + int data;
> +};
> +
> +#define BERLIN2_ADC_CHANNEL(n, t) \
> + { \
> + .channel = n, \
> + .datasheet_name = "channel"#n, \
> + .type = t, \
> + .indexed = 1, \
> + .info_mask_separate = BIT(IIO_CHAN_INFO_RAW), \
> + }
> +
> +static struct iio_chan_spec berlin2_adc_channels[] = {
> + BERLIN2_ADC_CHANNEL(0, IIO_VOLTAGE), /* external input */
> + BERLIN2_ADC_CHANNEL(1, IIO_VOLTAGE), /* external input */
> + BERLIN2_ADC_CHANNEL(2, IIO_VOLTAGE), /* external input */
> + BERLIN2_ADC_CHANNEL(3, IIO_VOLTAGE), /* external input */
> + BERLIN2_ADC_CHANNEL(4, IIO_VOLTAGE), /* reserved */
> + BERLIN2_ADC_CHANNEL(5, IIO_VOLTAGE), /* reserved */
> + { /* temperature sensor */
> + .channel = 6,
> + .datasheet_name = "channel6",
> + .type = IIO_TEMP,
> + .indexed = 0,
> + .info_mask_separate = BIT(IIO_CHAN_INFO_PROCESSED),
> + },
> + BERLIN2_ADC_CHANNEL(7, IIO_VOLTAGE), /* reserved */
> + IIO_CHAN_SOFT_TIMESTAMP(8), /* timestamp */
> +};
> +#define BERLIN2_N_CHANNELS ARRAY_SIZE(berlin2_adc_channels)
> +
> +static int berlin2_adc_read(struct iio_dev *indio_dev, int channel)
> +{
> + struct berlin2_adc_priv *priv = iio_priv(indio_dev);
> + int data, ret;
> +
> + mutex_lock(&priv->lock);
> +
> + /* Configure the ADC */
> + regmap_update_bits(priv->regmap, BERLIN2_SM_CTRL,
> + BERLIN2_SM_CTRL_ADC_RESET | BERLIN2_SM_CTRL_ADC_SEL_MASK
> + | BERLIN2_SM_CTRL_ADC_START,
> + BERLIN2_SM_CTRL_ADC_SEL(channel) | BERLIN2_SM_CTRL_ADC_START);
> +
> + ret = wait_event_interruptible_timeout(priv->wq, priv->data_available,
> + msecs_to_jiffies(1000));
> +
> + /* Disable the interrupts */
> + regmap_update_bits(priv->regmap, BERLIN2_SM_ADC_STATUS,
> + BERLIN2_SM_ADC_STATUS_INT_EN(channel), 0);
> +
> + if (ret == 0)
> + ret = -ETIMEDOUT;
> + if (ret < 0) {
> + mutex_unlock(&priv->lock);
> + return ret;
> + }
> +
> + regmap_update_bits(priv->regmap, BERLIN2_SM_CTRL,
> + BERLIN2_SM_CTRL_ADC_START, 0);
> +
> + data = priv->data;
> + priv->data = -1;
Is setting data = -1 not overkill with data_available there as well?
> + priv->data_available = false;
> +
> + mutex_unlock(&priv->lock);
> +
> + return data;
> +}
> +
> +static int berlin2_adc_tsen_read(struct iio_dev *indio_dev)
> +{
> + struct berlin2_adc_priv *priv = iio_priv(indio_dev);
> + int data, ret;
> +
> + mutex_lock(&priv->lock);
> +
> + /* Configure the ADC */
> + regmap_update_bits(priv->regmap, BERLIN2_SM_CTRL,
> + BERLIN2_SM_CTRL_TSEN_RESET | BERLIN2_SM_CTRL_ADC_ROTATE,
> + BERLIN2_SM_CTRL_ADC_ROTATE);
> +
> + /* Configure the temperature sensor */
> + regmap_update_bits(priv->regmap, BERLIN2_SM_TSEN_CTRL,
> + BERLIN2_SM_TSEN_CTRL_TRIM_MASK | BERLIN2_SM_TSEN_CTRL_SETTLING_MASK
> + | BERLIN2_SM_TSEN_CTRL_START,
> + BERLIN2_SM_TSEN_CTRL_TRIM(3) | BERLIN2_SM_TSEN_CTRL_SETTLING_12
> + | BERLIN2_SM_TSEN_CTRL_START);
> +
> + ret = wait_event_interruptible_timeout(priv->wq, priv->data_available,
> + msecs_to_jiffies(1000));
> +
> + /* Disable interrupts */
> + regmap_update_bits(priv->regmap, BERLIN2_SM_TSEN_STATUS,
> + BERLIN2_SM_TSEN_STATUS_INT_EN, 0);
> +
> + if (ret == 0)
> + ret = -ETIMEDOUT;
> + if (ret < 0) {
> + mutex_unlock(&priv->lock);
> + return ret;
> + }
> +
> + regmap_update_bits(priv->regmap, BERLIN2_SM_TSEN_CTRL,
> + BERLIN2_SM_TSEN_CTRL_START, 0);
> +
> + data = priv->data;
> + priv->data = -1;
> + priv->data_available = false;
> +
> + mutex_unlock(&priv->lock);
> +
> + return data;
> +}
> +
> +static int berlin2_adc_read_raw(struct iio_dev *indio_dev,
> + struct iio_chan_spec const *chan, int *val, int *val2,
> + long mask)
> +{
> + struct berlin2_adc_priv *priv = iio_priv(indio_dev);
> + int temp;
> +
> + switch (mask) {
> + case IIO_CHAN_INFO_RAW:
> + if (chan->type != IIO_VOLTAGE)
> + return -EINVAL;
> +
> + /* Enable the interrupts */
> + regmap_write(priv->regmap, BERLIN2_SM_ADC_STATUS,
> + BERLIN2_SM_ADC_STATUS_INT_EN(chan->channel));
> +
> + *val = berlin2_adc_read(indio_dev, chan->channel);
> + if (*val < 0)
> + return *val;
> +
> + return IIO_VAL_INT;
> + case IIO_CHAN_INFO_PROCESSED:
> + if (chan->type != IIO_TEMP)
> + return -EINVAL;
> +
> + /* Enable interrupts */
> + regmap_write(priv->regmap, BERLIN2_SM_TSEN_STATUS,
> + BERLIN2_SM_TSEN_STATUS_INT_EN);
> +
> + temp = berlin2_adc_tsen_read(indio_dev);
> + if (temp < 0)
> + return temp;
> +
> + if (temp > 2047)
> + temp = -(4096 - temp);
> +
> + /* Convert to Celsius */
Just to check... Celsius or milli degrees celsius?
(which is the ABI units - matched with hwmon)
> + *val = (temp * 100) / 264 - 270;
> + return IIO_VAL_INT;
> + default:
> + break;
> + }
> +
> + return -EINVAL;
> +}
> +
> +static irqreturn_t berlin2_adc_irq(int irq, void *private)
> +{
> + struct berlin2_adc_priv *priv = iio_priv(private);
> + unsigned val;
> +
> + regmap_read(priv->regmap, BERLIN2_SM_ADC_STATUS, &val);
> + if (val & BERLIN2_SM_ADC_STATUS_DATA_RDY_MASK) {
> + regmap_read(priv->regmap, BERLIN2_SM_ADC_DATA, &priv->data);
> + priv->data &= BERLIN2_SM_ADC_MASK;
> +
> + val &= ~BERLIN2_SM_ADC_STATUS_DATA_RDY_MASK;
> + regmap_write(priv->regmap, BERLIN2_SM_ADC_STATUS, val);
> +
> + priv->data_available = true;
> + wake_up_interruptible(&priv->wq);
> + }
> +
> + return IRQ_HANDLED;
> +}
> +
> +static irqreturn_t berlin2_adc_tsen_irq(int irq, void *private)
> +{
> + struct berlin2_adc_priv *priv = iio_priv(private);
> + unsigned val;
> +
> + regmap_read(priv->regmap, BERLIN2_SM_TSEN_STATUS, &val);
> + if (val & BERLIN2_SM_TSEN_STATUS_DATA_RDY) {
> + regmap_read(priv->regmap, BERLIN2_SM_TSEN_DATA, &priv->data);
> + priv->data &= BERLIN2_SM_TSEN_MASK;
> +
> + val &= ~BERLIN2_SM_TSEN_STATUS_DATA_RDY;
> + regmap_write(priv->regmap, BERLIN2_SM_TSEN_STATUS, val);
> +
> + priv->data_available = true;
> + wake_up_interruptible(&priv->wq);
> + }
> +
> + return IRQ_HANDLED;
> +}
> +
> +static const struct iio_info berlin2_adc_info = {
> + .driver_module = THIS_MODULE,
> + .read_raw = berlin2_adc_read_raw,
> +};
> +
> +static int berlin2_adc_probe(struct platform_device *pdev)
> +{
> + struct iio_dev *indio_dev;
> + struct berlin2_adc_priv *priv;
> + struct device_node *parent_np = of_get_parent(pdev->dev.of_node);
> + int ret;
> +
> + indio_dev = devm_iio_device_alloc(&pdev->dev,
> + sizeof(struct berlin2_adc_priv));
> + if (!indio_dev)
> + return -ENOMEM;
> +
> + priv = iio_priv(indio_dev);
> + platform_set_drvdata(pdev, indio_dev);
> +
> + priv->regmap = syscon_node_to_regmap(parent_np);
> + of_node_put(parent_np);
> + if (IS_ERR(priv->regmap))
> + return PTR_ERR(priv->regmap);
> +
> + priv->irq = platform_get_irq_byname(pdev, "adc");
> + if (priv->irq < 0)
> + return -ENODEV;
> +
> + priv->tsen_irq = platform_get_irq_byname(pdev, "tsen");
> + if (priv->tsen_irq < 0)
> + return -ENODEV;
> +
> + ret = devm_request_irq(&pdev->dev, priv->irq, berlin2_adc_irq, 0,
> + pdev->dev.driver->name, indio_dev);
> + if (ret)
> + return ret;
> +
> + ret = devm_request_irq(&pdev->dev, priv->tsen_irq, berlin2_adc_tsen_irq,
> + 0, pdev->dev.driver->name, indio_dev);
> + if (ret)
> + return ret;
> +
> + init_waitqueue_head(&priv->wq);
> + mutex_init(&priv->lock);
> +
> + indio_dev->dev.parent = &pdev->dev;
> + indio_dev->name = dev_name(&pdev->dev);
> + indio_dev->modes = INDIO_DIRECT_MODE;
> + indio_dev->info = &berlin2_adc_info;
> +
> + indio_dev->num_channels = BERLIN2_N_CHANNELS;
> + indio_dev->channels = berlin2_adc_channels;
> +
> + /* Power up the ADC */
> + regmap_update_bits(priv->regmap, BERLIN2_SM_CTRL,
> + BERLIN2_SM_CTRL_ADC_POWER, BERLIN2_SM_CTRL_ADC_POWER);
> +
> + ret = iio_device_register(indio_dev);
> + if (ret) {
> + /* Power down the ADC */
> + regmap_update_bits(priv->regmap, BERLIN2_SM_CTRL,
> + BERLIN2_SM_CTRL_ADC_POWER, 0);
> + return ret;
> + }
> +
> + return 0;
> +}
> +
> +static int berlin2_adc_remove(struct platform_device *pdev)
> +{
> + struct iio_dev *indio_dev = platform_get_drvdata(pdev);
> + struct berlin2_adc_priv *priv = iio_priv(indio_dev);
> +
> + iio_device_unregister(indio_dev);
> +
> + /* Power down the ADC */
> + regmap_update_bits(priv->regmap, BERLIN2_SM_CTRL,
> + BERLIN2_SM_CTRL_ADC_POWER, 0);
> +
> + return 0;
> +}
> +
> +static const struct of_device_id berlin2_adc_match[] = {
> + { .compatible = "marvell,berlin2-adc", },
> + { },
> +};
> +MODULE_DEVICE_TABLE(of, berlin2q_adc_match);
> +
> +static struct platform_driver berlin2_adc_driver = {
> + .driver = {
> + .name = "berlin2-adc",
> + .of_match_table = berlin2_adc_match,
> + },
> + .probe = berlin2_adc_probe,
> + .remove = berlin2_adc_remove,
> +};
> +module_platform_driver(berlin2_adc_driver);
> +
> +MODULE_AUTHOR("Antoine Tenart <antoine.tenart@xxxxxxxxxxxxxxxxxx>");
> +MODULE_DESCRIPTION("Marvell Berlin2 ADC driver");
> +MODULE_LICENSE("GPL v2");
>
--
To unsubscribe from this list: send the line "unsubscribe linux-iio" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
