On Sat, Mar 07, 2015 at 06:03:44PM +0000, Jonathan Cameron wrote:
> On 03/03/15 07:58, Markus Pargmann wrote:
> > This is a conversion queue driver for the mx25 SoC. It uses the central
> > ADC which is used by two seperate independent queues. This driver
> > prepares different conversion configurations for each possible input.
> > For a conversion it creates a conversionqueue of one item with the
> > correct configuration for the chosen channel. It then executes the queue
> > once and disables the conversion queue afterwards.
> >
> > The reference voltages are configurable through devicetree subnodes,
> > depending on the connections of the ADC inputs.
> >
> > Signed-off-by: Markus Pargmann <mpa@xxxxxxxxxxxxxx>
> > Signed-off-by: Denis Carikli <denis@xxxxxxxxxx>
> > Signed-off-by: Markus Pargmann <mpa@xxxxxxxxxxxxxx>
> There's an unbalanced regulator_enable that needs fixing.
> Deal with that in both the remove and the error cases
> and I'm happy.
>
> > ---
> >
> > Notes:
> > Changes in v7:
> > - Remove separate functions mx25_gcq_disable/enable_eoq() as they were used at
> > only one position
> > - Enforce an external reference regulator if one of the conversions uses it as
> > reference. The devm_regulator_get() call was moved into
> > mx25_gcq_setup_cfgs() to be able to acquire the reference regulator when
> > necessary.
> > - Store indio_dev as platform driver data instead of the private data. This
> > was changed in probe() and remove().
> >
> > Changes in v6:
> > - Added defines for a complete list of references in the dt binding macros
> >
> > drivers/iio/adc/Kconfig | 7 +
> > drivers/iio/adc/Makefile | 1 +
> > drivers/iio/adc/fsl-imx25-gcq.c | 356 ++++++++++++++++++++++++++++
> > include/dt-bindings/iio/adc/fsl-imx25-gcq.h | 18 ++
> > 4 files changed, 382 insertions(+)
> > create mode 100644 drivers/iio/adc/fsl-imx25-gcq.c
> > create mode 100644 include/dt-bindings/iio/adc/fsl-imx25-gcq.h
> >
> > diff --git a/drivers/iio/adc/Kconfig b/drivers/iio/adc/Kconfig
> > index 202daf889be2..947805d03d6c 100644
> > --- a/drivers/iio/adc/Kconfig
> > +++ b/drivers/iio/adc/Kconfig
> > @@ -154,6 +154,13 @@ config EXYNOS_ADC
> > of SoCs for drivers such as the touchscreen and hwmon to use to share
> > this resource.
> >
> > +config FSL_MX25_ADC
> > + tristate "Freescale MX25 ADC driver"
> > + depends on MFD_MX25_TSADC
> > + help
> > + Generic Conversion Queue driver used for general purpose ADC in the
> > + MX25. This driver supports single measurements using the MX25 ADC.
> > +
> > config LP8788_ADC
> > tristate "LP8788 ADC driver"
> > depends on MFD_LP8788
> > diff --git a/drivers/iio/adc/Makefile b/drivers/iio/adc/Makefile
> > index 0315af640866..409583975ba0 100644
> > --- a/drivers/iio/adc/Makefile
> > +++ b/drivers/iio/adc/Makefile
> > @@ -17,6 +17,7 @@ obj-$(CONFIG_AT91_ADC) += at91_adc.o
> > obj-$(CONFIG_AXP288_ADC) += axp288_adc.o
> > obj-$(CONFIG_CC10001_ADC) += cc10001_adc.o
> > obj-$(CONFIG_EXYNOS_ADC) += exynos_adc.o
> > +obj-$(CONFIG_FSL_MX25_ADC) += fsl-imx25-gcq.o
> > obj-$(CONFIG_LP8788_ADC) += lp8788_adc.o
> > obj-$(CONFIG_MAX1027) += max1027.o
> > obj-$(CONFIG_MAX1363) += max1363.o
> > diff --git a/drivers/iio/adc/fsl-imx25-gcq.c b/drivers/iio/adc/fsl-imx25-gcq.c
> > new file mode 100644
> > index 000000000000..18c21888aa4e
> > --- /dev/null
> > +++ b/drivers/iio/adc/fsl-imx25-gcq.c
> > @@ -0,0 +1,356 @@
> > +/*
> > + * Copyright (C) 2014-2015 Pengutronix, Markus Pargmann <mpa@xxxxxxxxxxxxxx>
> > + *
> > + * This program is free software; you can redistribute it and/or modify it under
> > + * the terms of the GNU General Public License version 2 as published by the
> > + * Free Software Foundation.
> > + *
> > + * This is the driver for the imx25 GCQ (Generic Conversion Queue)
> > + * connected to the imx25 ADC.
> > + */
> > +
> > +#include <dt-bindings/iio/adc/fsl-imx25-gcq.h>
> > +#include <linux/clk.h>
> > +#include <linux/iio/iio.h>
> > +#include <linux/interrupt.h>
> > +#include <linux/mfd/imx25-tsadc.h>
> > +#include <linux/module.h>
> > +#include <linux/of.h>
> > +#include <linux/platform_device.h>
> > +#include <linux/regmap.h>
> > +#include <linux/regulator/consumer.h>
> > +
> > +#define MX25_GCQ_TIMEOUT (msecs_to_jiffies(2000))
> > +
> > +enum mx25_gcq_cfgs {
> > + MX25_CFG_XP = 0,
> > + MX25_CFG_YP,
> > + MX25_CFG_XN,
> > + MX25_CFG_YN,
> > + MX25_CFG_WIPER,
> > + MX25_CFG_INAUX0,
> > + MX25_CFG_INAUX1,
> > + MX25_CFG_INAUX2,
> > + MX25_NUM_CFGS,
> > +};
> > +
> > +struct mx25_gcq_priv {
> > + struct regmap *regs;
> > + struct completion completed;
> > + unsigned int settling_time;
> > + struct clk *clk;
> > + int irq;
> > + struct regulator *ext_vref;
> > + u32 channel_vref_mv[MX25_NUM_CFGS];
> > +};
> > +
> > +#define MX25_CQG_CHAN(chan, id) {\
> > + .type = IIO_VOLTAGE,\
> > + .indexed = 1,\
> > + .channel = chan,\
> > + .info_mask_separate = BIT(IIO_CHAN_INFO_RAW),\
> > + .info_mask_shared_by_type = BIT(IIO_CHAN_INFO_SCALE),\
> > + .datasheet_name = id,\
> > +}
> > +
> > +static const struct iio_chan_spec mx25_gcq_channels[MX25_NUM_CFGS] = {
> > + MX25_CQG_CHAN(0, "xp"),
> > + MX25_CQG_CHAN(1, "yp"),
> > + MX25_CQG_CHAN(2, "xn"),
> > + MX25_CQG_CHAN(3, "yn"),
> > + MX25_CQG_CHAN(4, "wiper"),
> > + MX25_CQG_CHAN(5, "inaux0"),
> > + MX25_CQG_CHAN(6, "inaux1"),
> > + MX25_CQG_CHAN(7, "inaux2"),
> > +};
> > +
> > +static irqreturn_t mx25_gcq_irq(int irq, void *data)
> > +{
> > + struct mx25_gcq_priv *priv = data;
> > + u32 stats;
> > +
> > + regmap_read(priv->regs, MX25_ADCQ_SR, &stats);
> > +
> > + if (stats & MX25_ADCQ_SR_EOQ) {
> > + regmap_update_bits(priv->regs, MX25_ADCQ_MR,
> > + MX25_ADCQ_MR_EOQ_IRQ, MX25_ADCQ_MR_EOQ_IRQ);
> > + complete(&priv->completed);
> > + }
> > +
> > + /* Disable conversion queue run */
> > + regmap_update_bits(priv->regs, MX25_ADCQ_CR, MX25_ADCQ_CR_FQS, 0);
> > +
> > + /* Acknowledge all possible irqs */
> > + regmap_write(priv->regs, MX25_ADCQ_SR, MX25_ADCQ_SR_FRR |
> > + MX25_ADCQ_SR_FUR | MX25_ADCQ_SR_FOR |
> > + MX25_ADCQ_SR_EOQ | MX25_ADCQ_SR_PD);
> > +
> > + return IRQ_HANDLED;
> > +}
> > +
> > +static int mx25_gcq_get_raw_value(struct device *dev,
> > + struct iio_chan_spec const *chan,
> > + struct mx25_gcq_priv *priv,
> > + int *val)
> > +{
> > + long timeout;
> > + u32 data;
> > +
> > + /* Setup the configuration we want to use */
> > + regmap_write(priv->regs, MX25_ADCQ_ITEM_7_0,
> > + MX25_ADCQ_ITEM(0, chan->channel));
> > +
> > + regmap_update_bits(priv->regs, MX25_ADCQ_MR, MX25_ADCQ_MR_EOQ_IRQ, 0);
> > +
> > + /* Trigger queue for one run */
> > + regmap_update_bits(priv->regs, MX25_ADCQ_CR, MX25_ADCQ_CR_FQS,
> > + MX25_ADCQ_CR_FQS);
> > +
> > + timeout = wait_for_completion_interruptible_timeout(
> > + &priv->completed, MX25_GCQ_TIMEOUT);
> > + if (timeout < 0) {
> > + dev_err(dev,
> > + "ADC wait for measurement failed\n");
> > + return timeout;
> > + } else if (timeout == 0) {
> > + dev_err(dev, "ADC timed out\n");
> > + return -ETIMEDOUT;
> > + }
> > +
> > + regmap_read(priv->regs, MX25_ADCQ_FIFO, &data);
> > +
> > + *val = MX25_ADCQ_FIFO_DATA(data);
> > +
> > + return IIO_VAL_INT;
> > +}
> > +
> > +static int mx25_gcq_read_raw(struct iio_dev *indio_dev,
> > + struct iio_chan_spec const *chan, int *val,
> > + int *val2, long mask)
> > +{
> > + struct mx25_gcq_priv *priv = iio_priv(indio_dev);
> > + int ret = 0;
> > +
> > + switch (mask) {
> > + case IIO_CHAN_INFO_RAW:
> > + mutex_lock(&indio_dev->mlock);
> > + ret = mx25_gcq_get_raw_value(&indio_dev->dev, chan, priv, val);
> > + mutex_unlock(&indio_dev->mlock);
> > + return ret;
> > +
> > + case IIO_CHAN_INFO_SCALE:
> > + *val = priv->channel_vref_mv[chan->channel];
> > + *val2 = 12;
> > + return IIO_VAL_FRACTIONAL_LOG2;
> > +
> > + default:
> > + return -EINVAL;
> > + }
> > +}
> > +
> > +static const struct iio_info mx25_gcq_iio_info = {
> > + .read_raw = mx25_gcq_read_raw,
> > +};
> > +
> > +static const struct regmap_config mx25_gcq_regconfig = {
> > + .max_register = 0x5c,
> > + .reg_bits = 32,
> > + .val_bits = 32,
> > + .reg_stride = 4,
> > +};
> > +
> > +static int mx25_gcq_setup_cfgs(struct platform_device *pdev,
> > + struct mx25_gcq_priv *priv)
> > +{
> > + struct device_node *np = pdev->dev.of_node;
> > + struct device_node *child;
> > + struct device *dev = &pdev->dev;
> > + int ret, i;
> > + bool external_ref_used = false;
> > +
> > + /*
> > + * Setup all configurations registers with a default conversion
> > + * configuration for each input
> > + */
> > + for (i = 0; i < MX25_NUM_CFGS; ++i)
> > + regmap_write(priv->regs, MX25_ADCQ_CFG(i),
> > + MX25_ADCQ_CFG_YPLL_OFF |
> > + MX25_ADCQ_CFG_XNUR_OFF |
> > + MX25_ADCQ_CFG_XPUL_OFF |
> > + MX25_ADCQ_CFG_REFP_INT |
> > + MX25_ADCQ_CFG_IN(i) |
> > + MX25_ADCQ_CFG_REFN_NGND2);
> > +
> > + for_each_child_of_node(np, child) {
> > + u32 reg;
> > + u32 refp = MX25_ADCQ_CFG_REFP_INT;
> > + u32 refn = MX25_ADCQ_CFG_REFN_NGND2;
> > +
> > + ret = of_property_read_u32(child, "reg", ®);
> > + if (ret) {
> > + dev_err(dev, "Failed to get reg property\n");
> > + return ret;
> > + }
> > +
> > + if (reg >= MX25_NUM_CFGS) {
> > + dev_err(dev,
> > + "reg value is greater than the number of available configuration registers\n");
> > + return -EINVAL;
> > + }
> > +
> > + of_property_read_u32(child, "fsl,adc-refp", &refp);
> > + of_property_read_u32(child, "fsl,adc-refn", &refn);
> > +
> > + if (refp == MX25_ADC_REFP_EXT)
> > + external_ref_used = true;
> > +
> > + /*
> > + * Shift the read values to the correct positions within the
> > + * register.
> > + */
> > + refp = MX25_ADCQ_CFG_REFP(refp);
> > + refn = MX25_ADCQ_CFG_REFN(refn);
> > +
> > + if ((refp & MX25_ADCQ_CFG_REFP_MASK) != refp) {
> > + dev_err(dev, "Invalid fsl,adc-refp property value\n");
> > + return -EINVAL;
> > + }
> > + if ((refn & MX25_ADCQ_CFG_REFN_MASK) != refn) {
> > + dev_err(dev, "Invalid fsl,adc-refn property value");
> > + return -EINVAL;
> > + }
> > +
> > + regmap_update_bits(priv->regs, MX25_ADCQ_CFG(reg),
> > + MX25_ADCQ_CFG_REFP_MASK |
> > + MX25_ADCQ_CFG_REFN_MASK,
> > + refp | refn);
> > + }
> > + regmap_update_bits(priv->regs, MX25_ADCQ_CR,
> > + MX25_ADCQ_CR_FRST | MX25_ADCQ_CR_QRST,
> > + MX25_ADCQ_CR_FRST | MX25_ADCQ_CR_QRST);
> > +
> > + regmap_write(priv->regs, MX25_ADCQ_CR,
> > + MX25_ADCQ_CR_PDMSK | MX25_ADCQ_CR_QSM_FQS);
> > +
> > + if (external_ref_used) {
> > + priv->ext_vref = devm_regulator_get(&pdev->dev, "vref");
> > + if (IS_ERR(priv->ext_vref)) {
> > + dev_err(&pdev->dev, "Failed to get regulator for vref although the external reference voltage is used.\n");
> > + return PTR_ERR(priv->ext_vref);
> > + }
> > + }
> > +
> > + return 0;
> > +}
> > +
> > +static int mx25_gcq_probe(struct platform_device *pdev)
> > +{
> > + struct iio_dev *indio_dev;
> > + struct mx25_gcq_priv *priv;
> > + struct mx25_tsadc *tsadc = dev_get_drvdata(pdev->dev.parent);
> > + struct device *dev = &pdev->dev;
> > + struct resource *res;
> > + void __iomem *mem;
> > + int ret;
> > +
> > + indio_dev = devm_iio_device_alloc(&pdev->dev, sizeof(*priv));
> > + if (!indio_dev)
> > + return -ENOMEM;
> > +
> > + priv = iio_priv(indio_dev);
> > +
> > + res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
> > + mem = devm_ioremap_resource(dev, res);
> > + if (!mem)
> > + return -ENOMEM;
> > +
> > + priv->regs = devm_regmap_init_mmio(dev, mem, &mx25_gcq_regconfig);
> > + if (IS_ERR(priv->regs)) {
> > + dev_err(dev, "Failed to initialize regmap\n");
> > + return PTR_ERR(priv->regs);
> > + }
> > +
> > + init_completion(&priv->completed);
> > +
> > + ret = mx25_gcq_setup_cfgs(pdev, priv);
> > + if (ret)
> > + return ret;
> > +
> > + if (!IS_ERR_OR_NULL(priv->ext_vref)) {
> > + ret = regulator_enable(priv->ext_vref);
>
> I don't seen this being disabled anywhere. As devm_regulator_get
> will result in a regulator put on device exit and the regulator_put
> code is commented with enables must be balanced by disables this
> looks liable to cause trouble.
Thanks, I missed that. Will fix it.
Best Regards,
Markus
--
Pengutronix e.K. | |
Industrial Linux Solutions | http://www.pengutronix.de/ |
Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone: +49-5121-206917-0 |
Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 |
Attachment:
signature.asc
Description: Digital signature
