Clean up code by using PHY interface provided by the PHY driver under
PHY subsystem(drivers/phy/freescale/phy-fsl-imx8qm-hsio.c).
Signed-off-by: Richard Zhu <hongxing.zhu@xxxxxxx>
Reviewed-by: Frank Li <Frank.Li@xxxxxxx>
---
drivers/ata/ahci_imx.c | 365 +++++++++--------------------------------
1 file changed, 80 insertions(+), 285 deletions(-)
diff --git a/drivers/ata/ahci_imx.c b/drivers/ata/ahci_imx.c
index cb768f66f0a70..75258ed42d2ee 100644
--- a/drivers/ata/ahci_imx.c
+++ b/drivers/ata/ahci_imx.c
@@ -19,6 +19,7 @@
#include <linux/libata.h>
#include <linux/hwmon.h>
#include <linux/hwmon-sysfs.h>
+#include <linux/phy/phy.h>
#include <linux/thermal.h>
#include "ahci.h"
@@ -44,42 +45,6 @@ enum {
/* Clock Reset Register */
IMX_CLOCK_RESET = 0x7f3f,
IMX_CLOCK_RESET_RESET = 1 << 0,
- /* IMX8QM HSIO AHCI definitions */
- IMX8QM_SATA_PHY_RX_IMPED_RATIO_OFFSET = 0x03,
- IMX8QM_SATA_PHY_TX_IMPED_RATIO_OFFSET = 0x09,
- IMX8QM_SATA_PHY_IMPED_RATIO_85OHM = 0x6c,
- IMX8QM_LPCG_PHYX2_OFFSET = 0x00000,
- IMX8QM_CSR_PHYX2_OFFSET = 0x90000,
- IMX8QM_CSR_PHYX1_OFFSET = 0xa0000,
- IMX8QM_CSR_PHYX_STTS0_OFFSET = 0x4,
- IMX8QM_CSR_PCIEA_OFFSET = 0xb0000,
- IMX8QM_CSR_PCIEB_OFFSET = 0xc0000,
- IMX8QM_CSR_SATA_OFFSET = 0xd0000,
- IMX8QM_CSR_PCIE_CTRL2_OFFSET = 0x8,
- IMX8QM_CSR_MISC_OFFSET = 0xe0000,
-
- IMX8QM_LPCG_PHYX2_PCLK0_MASK = (0x3 << 16),
- IMX8QM_LPCG_PHYX2_PCLK1_MASK = (0x3 << 20),
- IMX8QM_PHY_APB_RSTN_0 = BIT(0),
- IMX8QM_PHY_MODE_SATA = BIT(19),
- IMX8QM_PHY_MODE_MASK = (0xf << 17),
- IMX8QM_PHY_PIPE_RSTN_0 = BIT(24),
- IMX8QM_PHY_PIPE_RSTN_OVERRIDE_0 = BIT(25),
- IMX8QM_PHY_PIPE_RSTN_1 = BIT(26),
- IMX8QM_PHY_PIPE_RSTN_OVERRIDE_1 = BIT(27),
- IMX8QM_STTS0_LANE0_TX_PLL_LOCK = BIT(4),
- IMX8QM_MISC_IOB_RXENA = BIT(0),
- IMX8QM_MISC_IOB_TXENA = BIT(1),
- IMX8QM_MISC_PHYX1_EPCS_SEL = BIT(12),
- IMX8QM_MISC_CLKREQN_OUT_OVERRIDE_1 = BIT(24),
- IMX8QM_MISC_CLKREQN_OUT_OVERRIDE_0 = BIT(25),
- IMX8QM_MISC_CLKREQN_IN_OVERRIDE_1 = BIT(28),
- IMX8QM_MISC_CLKREQN_IN_OVERRIDE_0 = BIT(29),
- IMX8QM_SATA_CTRL_RESET_N = BIT(12),
- IMX8QM_SATA_CTRL_EPCS_PHYRESET_N = BIT(7),
- IMX8QM_CTRL_BUTTON_RST_N = BIT(21),
- IMX8QM_CTRL_POWER_UP_RST_N = BIT(23),
- IMX8QM_CTRL_LTSSM_ENABLE = BIT(4),
};
enum ahci_imx_type {
@@ -95,14 +60,10 @@ struct imx_ahci_priv {
struct clk *sata_clk;
struct clk *sata_ref_clk;
struct clk *ahb_clk;
- struct clk *epcs_tx_clk;
- struct clk *epcs_rx_clk;
- struct clk *phy_apbclk;
- struct clk *phy_pclk0;
- struct clk *phy_pclk1;
- void __iomem *phy_base;
- struct gpio_desc *clkreq_gpiod;
struct regmap *gpr;
+ struct phy *sata_phy;
+ struct phy *cali_phy0;
+ struct phy *cali_phy1;
bool no_device;
bool first_time;
u32 phy_params;
@@ -450,201 +411,73 @@ ATTRIBUTE_GROUPS(fsl_sata_ahci);
static int imx8_sata_enable(struct ahci_host_priv *hpriv)
{
- u32 val, reg;
- int i, ret;
+ u32 val;
+ int ret;
struct imx_ahci_priv *imxpriv = hpriv->plat_data;
struct device *dev = &imxpriv->ahci_pdev->dev;
- /* configure the hsio for sata */
- ret = clk_prepare_enable(imxpriv->phy_pclk0);
- if (ret < 0) {
- dev_err(dev, "can't enable phy_pclk0.\n");
+ /*
+ * Since "REXT" pin is only present for first lane of i.MX8QM
+ * PHY, its calibration results will be stored, passed through
+ * to the second lane PHY, and shared with all three lane PHYs.
+ *
+ * Initialize the first two lane PHYs here, although only the
+ * third lane PHY is used by SATA.
+ */
+ ret = phy_init(imxpriv->cali_phy0);
+ if (ret) {
+ dev_err(dev, "cali PHY init failed\n");
return ret;
}
- ret = clk_prepare_enable(imxpriv->phy_pclk1);
- if (ret < 0) {
- dev_err(dev, "can't enable phy_pclk1.\n");
- goto disable_phy_pclk0;
+ ret = phy_power_on(imxpriv->cali_phy0);
+ if (ret) {
+ dev_err(dev, "cali PHY power on failed\n");
+ goto err_cali_phy0_exit;
}
- ret = clk_prepare_enable(imxpriv->epcs_tx_clk);
- if (ret < 0) {
- dev_err(dev, "can't enable epcs_tx_clk.\n");
- goto disable_phy_pclk1;
+ ret = phy_init(imxpriv->cali_phy1);
+ if (ret) {
+ dev_err(dev, "cali PHY1 init failed\n");
+ goto err_cali_phy0_off;
}
- ret = clk_prepare_enable(imxpriv->epcs_rx_clk);
- if (ret < 0) {
- dev_err(dev, "can't enable epcs_rx_clk.\n");
- goto disable_epcs_tx_clk;
+ ret = phy_power_on(imxpriv->cali_phy1);
+ if (ret) {
+ dev_err(dev, "cali PHY1 power on failed\n");
+ goto err_cali_phy1_exit;
}
- ret = clk_prepare_enable(imxpriv->phy_apbclk);
- if (ret < 0) {
- dev_err(dev, "can't enable phy_apbclk.\n");
- goto disable_epcs_rx_clk;
+ ret = phy_init(imxpriv->sata_phy);
+ if (ret) {
+ dev_err(dev, "sata PHY init failed\n");
+ goto err_cali_phy1_off;
}
- /* Configure PHYx2 PIPE_RSTN */
- regmap_read(imxpriv->gpr, IMX8QM_CSR_PCIEA_OFFSET +
- IMX8QM_CSR_PCIE_CTRL2_OFFSET, &val);
- if ((val & IMX8QM_CTRL_LTSSM_ENABLE) == 0) {
- /* The link of the PCIEA of HSIO is down */
- regmap_update_bits(imxpriv->gpr,
- IMX8QM_CSR_PHYX2_OFFSET,
- IMX8QM_PHY_PIPE_RSTN_0 |
- IMX8QM_PHY_PIPE_RSTN_OVERRIDE_0,
- IMX8QM_PHY_PIPE_RSTN_0 |
- IMX8QM_PHY_PIPE_RSTN_OVERRIDE_0);
+ ret = phy_set_mode(imxpriv->sata_phy, PHY_MODE_SATA);
+ if (ret) {
+ dev_err(dev, "unable to set SATA PHY mode\n");
+ goto err_sata_phy_exit;
}
- regmap_read(imxpriv->gpr, IMX8QM_CSR_PCIEB_OFFSET +
- IMX8QM_CSR_PCIE_CTRL2_OFFSET, ®);
- if ((reg & IMX8QM_CTRL_LTSSM_ENABLE) == 0) {
- /* The link of the PCIEB of HSIO is down */
- regmap_update_bits(imxpriv->gpr,
- IMX8QM_CSR_PHYX2_OFFSET,
- IMX8QM_PHY_PIPE_RSTN_1 |
- IMX8QM_PHY_PIPE_RSTN_OVERRIDE_1,
- IMX8QM_PHY_PIPE_RSTN_1 |
- IMX8QM_PHY_PIPE_RSTN_OVERRIDE_1);
- }
- if (((reg | val) & IMX8QM_CTRL_LTSSM_ENABLE) == 0) {
- /* The links of both PCIA and PCIEB of HSIO are down */
- regmap_update_bits(imxpriv->gpr,
- IMX8QM_LPCG_PHYX2_OFFSET,
- IMX8QM_LPCG_PHYX2_PCLK0_MASK |
- IMX8QM_LPCG_PHYX2_PCLK1_MASK,
- 0);
+ ret = phy_power_on(imxpriv->sata_phy);
+ if (ret) {
+ dev_err(dev, "sata PHY power up failed\n");
+ goto err_sata_phy_exit;
}
- /* set PWR_RST and BT_RST of csr_pciea */
- val = IMX8QM_CSR_PCIEA_OFFSET + IMX8QM_CSR_PCIE_CTRL2_OFFSET;
- regmap_update_bits(imxpriv->gpr,
- val,
- IMX8QM_CTRL_BUTTON_RST_N,
- IMX8QM_CTRL_BUTTON_RST_N);
- regmap_update_bits(imxpriv->gpr,
- val,
- IMX8QM_CTRL_POWER_UP_RST_N,
- IMX8QM_CTRL_POWER_UP_RST_N);
-
- /* PHYX1_MODE to SATA */
- regmap_update_bits(imxpriv->gpr,
- IMX8QM_CSR_PHYX1_OFFSET,
- IMX8QM_PHY_MODE_MASK,
- IMX8QM_PHY_MODE_SATA);
+ /* The cali_phy# can be turned off after SATA PHY is initialized. */
+ phy_power_off(imxpriv->cali_phy1);
+ phy_exit(imxpriv->cali_phy1);
+ phy_power_off(imxpriv->cali_phy0);
+ phy_exit(imxpriv->cali_phy0);
- /*
- * BIT0 RXENA 1, BIT1 TXENA 0
- * BIT12 PHY_X1_EPCS_SEL 1.
- */
- regmap_update_bits(imxpriv->gpr,
- IMX8QM_CSR_MISC_OFFSET,
- IMX8QM_MISC_IOB_RXENA,
- IMX8QM_MISC_IOB_RXENA);
- regmap_update_bits(imxpriv->gpr,
- IMX8QM_CSR_MISC_OFFSET,
- IMX8QM_MISC_IOB_TXENA,
- 0);
- regmap_update_bits(imxpriv->gpr,
- IMX8QM_CSR_MISC_OFFSET,
- IMX8QM_MISC_PHYX1_EPCS_SEL,
- IMX8QM_MISC_PHYX1_EPCS_SEL);
- /*
- * It is possible, for PCIe and SATA are sharing
- * the same clock source, HPLL or external oscillator.
- * When PCIe is in low power modes (L1.X or L2 etc),
- * the clock source can be turned off. In this case,
- * if this clock source is required to be toggling by
- * SATA, then SATA functions will be abnormal.
- * Set the override here to avoid it.
- */
- regmap_update_bits(imxpriv->gpr,
- IMX8QM_CSR_MISC_OFFSET,
- IMX8QM_MISC_CLKREQN_OUT_OVERRIDE_1 |
- IMX8QM_MISC_CLKREQN_OUT_OVERRIDE_0 |
- IMX8QM_MISC_CLKREQN_IN_OVERRIDE_1 |
- IMX8QM_MISC_CLKREQN_IN_OVERRIDE_0,
- IMX8QM_MISC_CLKREQN_OUT_OVERRIDE_1 |
- IMX8QM_MISC_CLKREQN_OUT_OVERRIDE_0 |
- IMX8QM_MISC_CLKREQN_IN_OVERRIDE_1 |
- IMX8QM_MISC_CLKREQN_IN_OVERRIDE_0);
-
- /* clear PHY RST, then set it */
- regmap_update_bits(imxpriv->gpr,
- IMX8QM_CSR_SATA_OFFSET,
- IMX8QM_SATA_CTRL_EPCS_PHYRESET_N,
- 0);
-
- regmap_update_bits(imxpriv->gpr,
- IMX8QM_CSR_SATA_OFFSET,
- IMX8QM_SATA_CTRL_EPCS_PHYRESET_N,
- IMX8QM_SATA_CTRL_EPCS_PHYRESET_N);
-
- /* CTRL RST: SET -> delay 1 us -> CLEAR -> SET */
- regmap_update_bits(imxpriv->gpr,
- IMX8QM_CSR_SATA_OFFSET,
- IMX8QM_SATA_CTRL_RESET_N,
- IMX8QM_SATA_CTRL_RESET_N);
- udelay(1);
- regmap_update_bits(imxpriv->gpr,
- IMX8QM_CSR_SATA_OFFSET,
- IMX8QM_SATA_CTRL_RESET_N,
- 0);
- regmap_update_bits(imxpriv->gpr,
- IMX8QM_CSR_SATA_OFFSET,
- IMX8QM_SATA_CTRL_RESET_N,
- IMX8QM_SATA_CTRL_RESET_N);
-
- /* APB reset */
- regmap_update_bits(imxpriv->gpr,
- IMX8QM_CSR_PHYX1_OFFSET,
- IMX8QM_PHY_APB_RSTN_0,
- IMX8QM_PHY_APB_RSTN_0);
-
- for (i = 0; i < 100; i++) {
- reg = IMX8QM_CSR_PHYX1_OFFSET +
- IMX8QM_CSR_PHYX_STTS0_OFFSET;
- regmap_read(imxpriv->gpr, reg, &val);
- val &= IMX8QM_STTS0_LANE0_TX_PLL_LOCK;
- if (val == IMX8QM_STTS0_LANE0_TX_PLL_LOCK)
- break;
- udelay(1);
- }
-
- if (val != IMX8QM_STTS0_LANE0_TX_PLL_LOCK) {
- dev_err(dev, "TX PLL of the PHY is not locked\n");
- ret = -ENODEV;
- } else {
- writeb(imxpriv->imped_ratio, imxpriv->phy_base +
- IMX8QM_SATA_PHY_RX_IMPED_RATIO_OFFSET);
- writeb(imxpriv->imped_ratio, imxpriv->phy_base +
- IMX8QM_SATA_PHY_TX_IMPED_RATIO_OFFSET);
- reg = readb(imxpriv->phy_base +
- IMX8QM_SATA_PHY_RX_IMPED_RATIO_OFFSET);
- if (unlikely(reg != imxpriv->imped_ratio))
- dev_info(dev, "Can't set PHY RX impedance ratio.\n");
- reg = readb(imxpriv->phy_base +
- IMX8QM_SATA_PHY_TX_IMPED_RATIO_OFFSET);
- if (unlikely(reg != imxpriv->imped_ratio))
- dev_info(dev, "Can't set PHY TX impedance ratio.\n");
- usleep_range(50, 100);
-
- /*
- * To reduce the power consumption, gate off
- * the PHY clks
- */
- clk_disable_unprepare(imxpriv->phy_apbclk);
- clk_disable_unprepare(imxpriv->phy_pclk1);
- clk_disable_unprepare(imxpriv->phy_pclk0);
- return ret;
- }
+ return 0;
- clk_disable_unprepare(imxpriv->phy_apbclk);
-disable_epcs_rx_clk:
- clk_disable_unprepare(imxpriv->epcs_rx_clk);
-disable_epcs_tx_clk:
- clk_disable_unprepare(imxpriv->epcs_tx_clk);
-disable_phy_pclk1:
- clk_disable_unprepare(imxpriv->phy_pclk1);
-disable_phy_pclk0:
- clk_disable_unprepare(imxpriv->phy_pclk0);
+err_sata_phy_exit:
+ phy_exit(imxpriv->sata_phy);
+err_cali_phy1_off:
+ phy_power_off(imxpriv->cali_phy1);
+err_cali_phy1_exit:
+ phy_exit(imxpriv->cali_phy1);
+err_cali_phy0_off:
+ phy_power_off(imxpriv->cali_phy0);
+err_cali_phy0_exit:
+ phy_exit(imxpriv->cali_phy0);
return ret;
}
@@ -698,6 +531,9 @@ static int imx_sata_enable(struct ahci_host_priv *hpriv)
}
} else if (imxpriv->type == AHCI_IMX8QM) {
ret = imx8_sata_enable(hpriv);
+ if (ret)
+ goto disable_clk;
+
}
usleep_range(1000, 2000);
@@ -736,8 +572,10 @@ static void imx_sata_disable(struct ahci_host_priv *hpriv)
break;
case AHCI_IMX8QM:
- clk_disable_unprepare(imxpriv->epcs_rx_clk);
- clk_disable_unprepare(imxpriv->epcs_tx_clk);
+ if (imxpriv->sata_phy) {
+ phy_power_off(imxpriv->sata_phy);
+ phy_exit(imxpriv->sata_phy);
+ }
break;
default:
@@ -760,6 +598,9 @@ static void ahci_imx_error_handler(struct ata_port *ap)
ahci_error_handler(ap);
+ if (imxpriv->type == AHCI_IMX8QM)
+ return;
+
if (!(imxpriv->first_time) || ahci_imx_hotplug)
return;
@@ -986,65 +827,19 @@ static const struct scsi_host_template ahci_platform_sht = {
static int imx8_sata_probe(struct device *dev, struct imx_ahci_priv *imxpriv)
{
- struct resource *phy_res;
- struct platform_device *pdev = imxpriv->ahci_pdev;
- struct device_node *np = dev->of_node;
-
- if (of_property_read_u32(np, "fsl,phy-imp", &imxpriv->imped_ratio))
- imxpriv->imped_ratio = IMX8QM_SATA_PHY_IMPED_RATIO_85OHM;
- phy_res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "phy");
- if (phy_res) {
- imxpriv->phy_base = devm_ioremap(dev, phy_res->start,
- resource_size(phy_res));
- if (!imxpriv->phy_base) {
- dev_err(dev, "error with ioremap\n");
- return -ENOMEM;
- }
- } else {
- dev_err(dev, "missing *phy* reg region.\n");
- return -ENOMEM;
- }
- imxpriv->gpr =
- syscon_regmap_lookup_by_phandle(np, "hsio");
- if (IS_ERR(imxpriv->gpr)) {
- dev_err(dev, "unable to find gpr registers\n");
- return PTR_ERR(imxpriv->gpr);
- }
-
- imxpriv->epcs_tx_clk = devm_clk_get(dev, "epcs_tx");
- if (IS_ERR(imxpriv->epcs_tx_clk)) {
- dev_err(dev, "can't get epcs_tx_clk clock.\n");
- return PTR_ERR(imxpriv->epcs_tx_clk);
- }
- imxpriv->epcs_rx_clk = devm_clk_get(dev, "epcs_rx");
- if (IS_ERR(imxpriv->epcs_rx_clk)) {
- dev_err(dev, "can't get epcs_rx_clk clock.\n");
- return PTR_ERR(imxpriv->epcs_rx_clk);
- }
- imxpriv->phy_pclk0 = devm_clk_get(dev, "phy_pclk0");
- if (IS_ERR(imxpriv->phy_pclk0)) {
- dev_err(dev, "can't get phy_pclk0 clock.\n");
- return PTR_ERR(imxpriv->phy_pclk0);
- }
- imxpriv->phy_pclk1 = devm_clk_get(dev, "phy_pclk1");
- if (IS_ERR(imxpriv->phy_pclk1)) {
- dev_err(dev, "can't get phy_pclk1 clock.\n");
- return PTR_ERR(imxpriv->phy_pclk1);
- }
- imxpriv->phy_apbclk = devm_clk_get(dev, "phy_apbclk");
- if (IS_ERR(imxpriv->phy_apbclk)) {
- dev_err(dev, "can't get phy_apbclk clock.\n");
- return PTR_ERR(imxpriv->phy_apbclk);
- }
-
- /* Fetch GPIO, then enable the external OSC */
- imxpriv->clkreq_gpiod = devm_gpiod_get_optional(dev, "clkreq",
- GPIOD_OUT_LOW | GPIOD_FLAGS_BIT_NONEXCLUSIVE);
- if (IS_ERR(imxpriv->clkreq_gpiod))
- return PTR_ERR(imxpriv->clkreq_gpiod);
- if (imxpriv->clkreq_gpiod)
- gpiod_set_consumer_name(imxpriv->clkreq_gpiod, "SATA CLKREQ");
-
+ imxpriv->sata_phy = devm_phy_get(dev, "sata-phy");
+ if (IS_ERR(imxpriv->sata_phy))
+ return dev_err_probe(dev, PTR_ERR(imxpriv->sata_phy),
+ "Failed to get sata_phy\n");
+
+ imxpriv->cali_phy0 = devm_phy_get(dev, "cali-phy0");
+ if (IS_ERR(imxpriv->cali_phy0))
+ return dev_err_probe(dev, PTR_ERR(imxpriv->cali_phy0),
+ "Failed to get cali_phy0\n");
+ imxpriv->cali_phy1 = devm_phy_get(dev, "cali-phy1");
+ if (IS_ERR(imxpriv->cali_phy1))
+ return dev_err_probe(dev, PTR_ERR(imxpriv->cali_phy1),
+ "Failed to get cali_phy1\n");
return 0;
}
--
2.37.1
