[REGRESSION][BISECTED][STABLE] hdparm errors since 28ab9769117c

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Hello Igor, hello Niklas,

on my NAS I am encountering the following issue since v6.6.44 (LTS),
when executing the hdparm command for my WD-WCC7K4NLX884 drives to get
the active or standby state:

    $ hdparm -C /dev/sda
    /dev/sda:
    SG_IO: bad/missing sense data, sb[]:  f0 00 01 00 50 40 ff 0a 00 00 78 00 00 1d 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
     drive state is:  unknown


While the expected output is the following:

    $ hdparm -C /dev/sda
    /dev/sda:
     drive state is:  active/idle

I did a bisection within the stable series and found the following
commit to be the first bad one:

    28ab9769117c ("ata: libata-scsi: Honor the D_SENSE bit for CK_COND=1 and no error")

According to kernel.dance the same commit was also backported to the
v6.10.3 and v6.1.103 stable kernels and I could not find any commit or
pending patch with a "Fixes:" tag for the offending commit.

So far I have not been able to test with the mainline kernel as this is
a remote device which I couldn't rescue in case of a boot failure. Also
just for transparency it does have the out of tree ZFS module loaded,
but AFAIU this shouldn't be an issue here, as the commit seems clearly
related to the error. If needed I can test with an untainted mainline
kernel on Friday when I'm near the device.

I have attached the output of hdparm -I below and would be happy to
provide further debug information or test patches.

Cheers,
Christian

---

#regzbot introduced: 28ab9769117c
#regzbot title: ata: libata-scsi: Sense data errors breaking hdparm with WD drives

---

$ pacman -Q hdparm
hdparm 9.65-2

$ hdparm -I /dev/sda

/dev/sda:

ATA device, with non-removable media
	Model Number:       WDC WD40EFRX-68N32N0
	Serial Number:      WD-WCC7K4NLX884
	Firmware Revision:  82.00A82
	Transport:          Serial, SATA 1.0a, SATA II Extensions, SATA Rev 2.5, SATA Rev 2.6, SATA Rev 3.0
Standards:
	Used: unknown (minor revision code 0x006d) 
	Supported: 10 9 8 7 6 5 
	Likely used: 10
Configuration:
	Logical		max	current
	cylinders	16383	0
	heads		16	0
	sectors/track	63	0
	--
	LBA    user addressable sectors:   268435455
	LBA48  user addressable sectors:  7814037168
	Logical  Sector size:                   512 bytes
	Physical Sector size:                  4096 bytes
	Logical Sector-0 offset:                  0 bytes
	device size with M = 1024*1024:     3815447 MBytes
	device size with M = 1000*1000:     4000787 MBytes (4000 GB)
	cache/buffer size  = unknown
	Form Factor: 3.5 inch
	Nominal Media Rotation Rate: 5400
Capabilities:
	LBA, IORDY(can be disabled)
	Queue depth: 32
	Standby timer values: spec'd by Standard, with device specific minimum
	R/W multiple sector transfer: Max = 16	Current = 16
	DMA: mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 udma4 udma5 *udma6 
	     Cycle time: min=120ns recommended=120ns
	PIO: pio0 pio1 pio2 pio3 pio4 
	     Cycle time: no flow control=120ns  IORDY flow control=120ns
Commands/features:
	Enabled	Supported:
	   *	SMART feature set
	    	Security Mode feature set
	   *	Power Management feature set
	   *	Write cache
	   *	Look-ahead
	   *	Host Protected Area feature set
	   *	WRITE_BUFFER command
	   *	READ_BUFFER command
	   *	NOP cmd
	   *	DOWNLOAD_MICROCODE
	    	Power-Up In Standby feature set
	   *	SET_FEATURES required to spinup after power up
	    	SET_MAX security extension
	   *	48-bit Address feature set
	   *	Device Configuration Overlay feature set
	   *	Mandatory FLUSH_CACHE
	   *	FLUSH_CACHE_EXT
	   *	SMART error logging
	   *	SMART self-test
	   *	General Purpose Logging feature set
	   *	64-bit World wide name
	   *	IDLE_IMMEDIATE with UNLOAD
	   *	WRITE_UNCORRECTABLE_EXT command
	   *	{READ,WRITE}_DMA_EXT_GPL commands
	   *	Segmented DOWNLOAD_MICROCODE
	   *	Gen1 signaling speed (1.5Gb/s)
	   *	Gen2 signaling speed (3.0Gb/s)
	   *	Gen3 signaling speed (6.0Gb/s)
	   *	Native Command Queueing (NCQ)
	   *	Host-initiated interface power management
	   *	Phy event counters
	   *	Idle-Unload when NCQ is active
	   *	NCQ priority information
	   *	READ_LOG_DMA_EXT equivalent to READ_LOG_EXT
	   *	DMA Setup Auto-Activate optimization
	   *	Device-initiated interface power management
	   *	Software settings preservation
	   *	SMART Command Transport (SCT) feature set
	   *	SCT Write Same (AC2)
	   *	SCT Error Recovery Control (AC3)
	   *	SCT Features Control (AC4)
	   *	SCT Data Tables (AC5)
	    	unknown 206[12] (vendor specific)
	    	unknown 206[13] (vendor specific)
	   *	DOWNLOAD MICROCODE DMA command
	   *	WRITE BUFFER DMA command
	   *	READ BUFFER DMA command
Security: 
	Master password revision code = 65534
		supported
	not	enabled
	not	locked
		frozen
	not	expired: security count
		supported: enhanced erase
	504min for SECURITY ERASE UNIT. 504min for ENHANCED SECURITY ERASE UNIT.
Logical Unit WWN Device Identifier: 50014ee2647735a1
	NAA		: 5
	IEEE OUI	: 0014ee
	Unique ID	: 2647735a1
Checksum: correct

Attachment: signature.asc
Description: PGP signature


[Index of Archives]     [Linux Filesystems]     [Linux SCSI]     [Linux RAID]     [Git]     [Kernel Newbies]     [Linux Newbie]     [Security]     [Netfilter]     [Bugtraq]     [Yosemite News]     [MIPS Linux]     [ARM Linux]     [Linux Security]     [Samba]     [Device Mapper]

  Powered by Linux