Re: [PATCH v3 2/4] ata: ahci_imx: Clean up code by using i.MX8Q HSIO PHY driver

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Tue, Jul 16, 2024 at 11:18:13AM +0800, Richard Zhu wrote:
> Clean up code by using PHY interface.
> 
> Signed-off-by: Richard Zhu <hongxing.zhu@xxxxxxx>
> ---
>  drivers/ata/ahci_imx.c | 396 ++++++++++-------------------------------
>  1 file changed, 98 insertions(+), 298 deletions(-)
> 
> diff --git a/drivers/ata/ahci_imx.c b/drivers/ata/ahci_imx.c
> index cb768f66f0a70..e94c0fdea2260 100644
> --- a/drivers/ata/ahci_imx.c
> +++ b/drivers/ata/ahci_imx.c
> @@ -986,65 +827,22 @@ static const struct scsi_host_template ahci_platform_sht = {
>  
>  static int imx8_sata_probe(struct device *dev, struct imx_ahci_priv *imxpriv)
>  {
> -	struct resource *phy_res;
> -	struct platform_device *pdev = imxpriv->ahci_pdev;
> -	struct device_node *np = dev->of_node;
> -
> -	if (of_property_read_u32(np, "fsl,phy-imp", &imxpriv->imped_ratio))
> -		imxpriv->imped_ratio = IMX8QM_SATA_PHY_IMPED_RATIO_85OHM;
> -	phy_res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "phy");
> -	if (phy_res) {
> -		imxpriv->phy_base = devm_ioremap(dev, phy_res->start,
> -					resource_size(phy_res));
> -		if (!imxpriv->phy_base) {
> -			dev_err(dev, "error with ioremap\n");
> -			return -ENOMEM;
> -		}
> -	} else {
> -		dev_err(dev, "missing *phy* reg region.\n");
> -		return -ENOMEM;
> -	}
> -	imxpriv->gpr =
> -		 syscon_regmap_lookup_by_phandle(np, "hsio");
> -	if (IS_ERR(imxpriv->gpr)) {
> -		dev_err(dev, "unable to find gpr registers\n");
> -		return PTR_ERR(imxpriv->gpr);
> -	}
> -
> -	imxpriv->epcs_tx_clk = devm_clk_get(dev, "epcs_tx");
> -	if (IS_ERR(imxpriv->epcs_tx_clk)) {
> -		dev_err(dev, "can't get epcs_tx_clk clock.\n");
> -		return PTR_ERR(imxpriv->epcs_tx_clk);
> -	}
> -	imxpriv->epcs_rx_clk = devm_clk_get(dev, "epcs_rx");
> -	if (IS_ERR(imxpriv->epcs_rx_clk)) {
> -		dev_err(dev, "can't get epcs_rx_clk clock.\n");
> -		return PTR_ERR(imxpriv->epcs_rx_clk);
> -	}
> -	imxpriv->phy_pclk0 = devm_clk_get(dev, "phy_pclk0");
> -	if (IS_ERR(imxpriv->phy_pclk0)) {
> -		dev_err(dev, "can't get phy_pclk0 clock.\n");
> -		return PTR_ERR(imxpriv->phy_pclk0);
> -	}
> -	imxpriv->phy_pclk1 = devm_clk_get(dev, "phy_pclk1");
> -	if (IS_ERR(imxpriv->phy_pclk1)) {
> -		dev_err(dev, "can't get phy_pclk1 clock.\n");
> -		return PTR_ERR(imxpriv->phy_pclk1);
> -	}
> -	imxpriv->phy_apbclk = devm_clk_get(dev, "phy_apbclk");
> -	if (IS_ERR(imxpriv->phy_apbclk)) {
> -		dev_err(dev, "can't get phy_apbclk clock.\n");
> -		return PTR_ERR(imxpriv->phy_apbclk);
> -	}
> -
> -	/* Fetch GPIO, then enable the external OSC */
> -	imxpriv->clkreq_gpiod = devm_gpiod_get_optional(dev, "clkreq",
> -				GPIOD_OUT_LOW | GPIOD_FLAGS_BIT_NONEXCLUSIVE);
> -	if (IS_ERR(imxpriv->clkreq_gpiod))
> -		return PTR_ERR(imxpriv->clkreq_gpiod);
> -	if (imxpriv->clkreq_gpiod)
> -		gpiod_set_consumer_name(imxpriv->clkreq_gpiod, "SATA CLKREQ");
> -
> +	if (!(dev->bus_dma_limit))
> +		dev->bus_dma_limit = DMA_BIT_MASK(32);

These two lines look like a unrelated change, should be in a separate commit
with a proper commit message.


Kind regards,
Niklas




[Index of Archives]     [Linux Filesystems]     [Linux SCSI]     [Linux RAID]     [Git]     [Kernel Newbies]     [Linux Newbie]     [Security]     [Netfilter]     [Bugtraq]     [Yosemite News]     [MIPS Linux]     [ARM Linux]     [Linux Security]     [Samba]     [Device Mapper]

  Powered by Linux