Hello Niklas,
On 24/05/28 10:19pm, Niklas Cassel wrote:
> Hello Tim,
>
> On Tue, May 28, 2024 at 01:17:51PM -0600, Jens Axboe wrote:
> > (Adding Damien, he's the ATA guy these days - leaving the below intact)
> >
> > On 5/28/24 1:15 PM, Thomas Gleixner wrote:
> > > Tim!
> > >
> > > On Tue, May 28 2024 at 17:43, Tim Teichmann wrote:
> > >> On 24/05/27 07:17pm, Thomas Gleixner wrote:
> > >> I've just tested the fix you've provided in the previous email.
> > >> The exact patches are attached to the ticket in the archlinux bugtracker[0].
> > >
> > > Thanks! I will write a proper changelog and ship it.
> > >
> > >> The error regarding CPU scheduling disappeared for both kernel verions[0].
> > >> However, the ATA bus error still occurs.
> > >>
> > >> Also, I suppose that the ATA bus error is the same as the previous one,
> > >> because the only value that changes in the exception message is SAct.
> > >>
> > >> This is the message of the ATA error before the patch:
> > >>
> > >>>> May 23 23:36:49 archlinux kernel: smpboot: x86: Booting SMP configuration:
> > >>>> May 23 23:36:49 archlinux kernel: .... node #0, CPUs: #2 #4 #6
> > >>>> May 23 23:36:49 archlinux kernel: __common_interrupt: 2.55 No irq handler for vector
> > >>>> May 23 23:36:49 archlinux kernel: __common_interrupt: 4.55 No irq handler for vector
> > >>>> May 23 23:36:49 archlinux kernel: __common_interrupt: 6.55 No irq handler for vector
> > >>>>
> > >>>> ATA stuff:
> > >>>>
> > >>>> May 23 23:36:59 archlinux kernel: ata2.00: exception Emask 0x10 SAct 0x1fffe000 SErr 0x40d0002 action 0xe frozen
> > >>>
> > >>> That's probably just the fallout of the above.
> > >
> > > It's in reality not related and I saw some other AHCI fallout fly by.
> > >
> > >> And that's the message after the patch:
> > >>
> > >> [ 4.877584] ata2.00: exception Emask 0x10 SAct 0x80000000 SErr 0x40d0002 action 0xe frozen
> > >>
> > >> The full dmesg outputs are in the attachments.
> > >
> > > Cc'ed the AHCI people and left the info around for them.
>
> We recently (kernel v6.9) enabled LPM for all AHCI controllers if:
> -The AHCI controller reports that it supports LPM, and
> -The drive reports that it supports LPM (DIPM), and
> -CONFIG_SATA_MOBILE_LPM_POLICY=3, and
> -The port is not defined as external in the per port PxCMD register, and
> -The port is not defined as hotplug capable in the per port PxCMD register.
>
> However, there appears to be some drives (usually cheap ones that we've never
> heard about) that reports that they support DIPM, but when actually turning
> it on, they stop working.
>
> Looking at the dmesg, you seem to have two SATA drives:
>
> > >> [ 0.957220] ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
> > >> [ 0.957984] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
> > >> [ 0.958027] ata3.00: ATA-8: TOSHIBA HDWD110, MS2OA8J0, max UDMA/133
> > >> [ 0.958069] ata2.00: ATA-11: Apacer AS340 120GB, AP612PE0, max UDMA/133
>
>
> ata3 (TOSHIBA HDWD110) appears to work correctly.
>
> ata2 (Apacer AS340 120GB) results in command timeouts and
> "a change in device presence has been detected" being set in PxSERR.DIAG.X.
>
> > >> [ 2.964262] ata2.00: exception Emask 0x10 SAct 0x80 SErr 0x40d0002 action 0xe frozen
> > >> [ 2.964274] ata2.00: irq_stat 0x00000040, connection status changed
> > >> [ 2.964279] ata2: SError: { RecovComm PHYRdyChg CommWake 10B8B DevExch }
> > >> [ 2.964288] ata2.00: failed command: READ FPDMA QUEUED
> > >> [ 2.964291] ata2.00: cmd 60/08:38:80:ff:f1/00:00:0d:00:00/40 tag 7 ncq dma 4096 in
> > >> res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x10 (ATA bus error)
> > >> [ 2.964307] ata2.00: status: { DRDY }
> > >> [ 2.964318] ata2: hard resetting link
>
>
> Could you please try the following patch (quirk):
>
> diff --git a/drivers/ata/libata-core.c b/drivers/ata/libata-core.c
> index c449d60d9bb9..24ebcad65b65 100644
> --- a/drivers/ata/libata-core.c
> +++ b/drivers/ata/libata-core.c
> @@ -4199,6 +4199,9 @@ static const struct ata_blacklist_entry ata_device_blacklist [] = {
> ATA_HORKAGE_ZERO_AFTER_TRIM |
> ATA_HORKAGE_NOLPM },
>
> + /* Apacer models with LPM issues */
> + { "Apacer AS340*", NULL, ATA_HORKAGE_NOLPM },
> +
> /* These specific Samsung models/firmware-revs do not handle LPM well */
> { "SAMSUNG MZMPC128HBFU-000MV", "CXM14M1Q", ATA_HORKAGE_NOLPM },
> { "SAMSUNG SSD PM830 mSATA *", "CXM13D1Q", ATA_HORKAGE_NOLPM },
>
>
>
> Kind regards,
> Niklas
I've just tested the patch you've provided [0] and it works without
throwing ATA exceptions.
The full dmesg output is attached below.
Thank you,
Tim
[0]: https://gitlab.archlinux.org/archlinux/packaging/packages/linux/-/issues/56#note_188819
[ 0.000000] Linux version 6.9.2-arch1-1.3 (linux@archlinux) (gcc (GCC) 14.1.1 20240522, GNU ld (GNU Binutils) 2.42.0) #1 SMP PREEMPT_DYNAMIC Tue, 28 May 2024 21:16:00 +0000 [ 0.000000] Command line: BOOT_IMAGE=/vmlinuz-linux root=UUID=963daeed-0888-4658-9f17-18bd343dfb2a rw zswap.enabled=0 rootfstype=ext4 loglevel=3 quiet [ 0.000000] BIOS-provided physical RAM map: [ 0.000000] BIOS-e820: [mem 0x0000000000000000-0x000000000009f7ff] usable [ 0.000000] BIOS-e820: [mem 0x000000000009f800-0x000000000009ffff] reserved [ 0.000000] BIOS-e820: [mem 0x00000000000f0000-0x00000000000fffff] reserved [ 0.000000] BIOS-e820: [mem 0x0000000000100000-0x00000000bfdeffff] usable [ 0.000000] BIOS-e820: [mem 0x00000000bfdf0000-0x00000000bfdf2fff] ACPI NVS [ 0.000000] BIOS-e820: [mem 0x00000000bfdf3000-0x00000000bfdfffff] ACPI data [ 0.000000] BIOS-e820: [mem 0x00000000bfe00000-0x00000000bfefffff] reserved [ 0.000000] BIOS-e820: [mem 0x00000000e0000000-0x00000000efffffff] reserved [ 0.000000] BIOS-e820: [mem 0x00000000fec00000-0x00000000ffffffff] reserved [ 0.000000] BIOS-e820: [mem 0x0000000100000000-0x000000043effffff] usable [ 0.000000] NX (Execute Disable) protection: active [ 0.000000] APIC: Static calls initialized [ 0.000000] SMBIOS 2.4 present. [ 0.000000] DMI: Gigabyte Technology Co., Ltd. GA-78LMT-USB3 R2/GA-78LMT-USB3 R2, BIOS F1 11/08/2017 [ 0.000000] tsc: Fast TSC calibration using PIT [ 0.000000] tsc: Detected 3322.009 MHz processor [ 0.002928] e820: update [mem 0x00000000-0x00000fff] usable ==> reserved [ 0.002932] e820: remove [mem 0x000a0000-0x000fffff] usable [ 0.002938] last_pfn = 0x43f000 max_arch_pfn = 0x400000000 [ 0.002947] total RAM covered: 3070M [ 0.003245] Found optimal setting for mtrr clean up [ 0.003246] gran_size: 64K chunk_size: 4M num_reg: 3 lose cover RAM: 0G [ 0.003251] MTRR map: 7 entries (4 fixed + 3 variable; max 21), built from 9 variable MTRRs [ 0.003253] x86/PAT: Configuration [0-7]: WB WC UC- UC WB WP UC- WT [ 0.004118] e820: update [mem 0xbfe00000-0xffffffff] usable ==> reserved [ 0.004128] last_pfn = 0xbfdf0 max_arch_pfn = 0x400000000 [ 0.007039] found SMP MP-table at [mem 0x000f5ea0-0x000f5eaf] [ 0.007060] Using GB pages for direct mapping [ 0.007180] RAMDISK: [mem 0x31c9f000-0x34e46fff] [ 0.007303] ACPI: Early table checksum verification disabled [ 0.007308] ACPI: RSDP 0x00000000000F78B0 000014 (v00 GBT ) [ 0.007312] ACPI: RSDT 0x00000000BFDF3000 000040 (v01 GBT GBTUACPI 42302E31 GBTU 01010101) [ 0.007319] ACPI: FACP 0x00000000BFDF3080 000074 (v01 GBT GBTUACPI 42302E31 GBTU 01010101) [ 0.007325] ACPI: DSDT 0x00000000BFDF3100 0069E7 (v01 GBT GBTUACPI 00001000 MSFT 03000000) [ 0.007330] ACPI: FACS 0x00000000BFDF0000 000040 [ 0.007334] ACPI: MSDM 0x00000000BFDF9BC0 000055 (v03 GBT GBTUACPI 42302E31 GBTU 01010101) [ 0.007338] ACPI: HPET 0x00000000BFDF9C40 000038 (v01 GBT GBTUACPI 42302E31 GBTU 00000098) [ 0.007342] ACPI: MCFG 0x00000000BFDF9C80 00003C (v01 GBT GBTUACPI 42302E31 GBTU 01010101) [ 0.007346] ACPI: TAMG 0x00000000BFDF9CC0 000022 (v01 GBT GBT B0 5455312E BG?? 00000101) [ 0.007350] ACPI: APIC 0x00000000BFDF9B00 0000BC (v01 GBT GBTUACPI 42302E31 GBTU 01010101) [ 0.007354] ACPI: SSDT 0x00000000BFDF9D60 001714 (v01 AMD POWERNOW 00000001 AMD 00000001) [ 0.007358] ACPI: Reserving FACP table memory at [mem 0xbfdf3080-0xbfdf30f3] [ 0.007359] ACPI: Reserving DSDT table memory at [mem 0xbfdf3100-0xbfdf9ae6] [ 0.007361] ACPI: Reserving FACS table memory at [mem 0xbfdf0000-0xbfdf003f] [ 0.007362] ACPI: Reserving MSDM table memory at [mem 0xbfdf9bc0-0xbfdf9c14] [ 0.007364] ACPI: Reserving HPET table memory at [mem 0xbfdf9c40-0xbfdf9c77] [ 0.007365] ACPI: Reserving MCFG table memory at [mem 0xbfdf9c80-0xbfdf9cbb] [ 0.007366] ACPI: Reserving TAMG table memory at [mem 0xbfdf9cc0-0xbfdf9ce1] [ 0.007367] ACPI: Reserving APIC table memory at [mem 0xbfdf9b00-0xbfdf9bbb] [ 0.007368] ACPI: Reserving SSDT table memory at [mem 0xbfdf9d60-0xbfdfb473] [ 0.007432] No NUMA configuration found [ 0.007433] Faking a node at [mem 0x0000000000000000-0x000000043effffff] [ 0.007436] NODE_DATA(0) allocated [mem 0x43effb000-0x43effffff] [ 0.007477] Zone ranges: [ 0.007478] DMA [mem 0x0000000000001000-0x0000000000ffffff] [ 0.007480] DMA32 [mem 0x0000000001000000-0x00000000ffffffff] [ 0.007482] Normal [mem 0x0000000100000000-0x000000043effffff] [ 0.007484] Device empty [ 0.007485] Movable zone start for each node [ 0.007486] Early memory node ranges [ 0.007487] node 0: [mem 0x0000000000001000-0x000000000009efff] [ 0.007488] node 0: [mem 0x0000000000100000-0x00000000bfdeffff] [ 0.007490] node 0: [mem 0x0000000100000000-0x000000043effffff] [ 0.007493] Initmem setup node 0 [mem 0x0000000000001000-0x000000043effffff] [ 0.007499] On node 0, zone DMA: 1 pages in unavailable ranges [ 0.007539] On node 0, zone DMA: 97 pages in unavailable ranges [ 0.055138] On node 0, zone Normal: 528 pages in unavailable ranges [ 0.055214] On node 0, zone Normal: 4096 pages in unavailable ranges [ 0.055397] ACPI: PM-Timer IO Port: 0x4008 [ 0.055409] ACPI: LAPIC_NMI (acpi_id[0x00] dfl dfl lint[0x1]) [ 0.055411] ACPI: LAPIC_NMI (acpi_id[0x01] dfl dfl lint[0x1]) [ 0.055413] ACPI: LAPIC_NMI (acpi_id[0x02] dfl dfl lint[0x1]) [ 0.055414] ACPI: LAPIC_NMI (acpi_id[0x03] dfl dfl lint[0x1]) [ 0.055415] ACPI: LAPIC_NMI (acpi_id[0x04] dfl dfl lint[0x1]) [ 0.055416] ACPI: LAPIC_NMI (acpi_id[0x05] dfl dfl lint[0x1]) [ 0.055417] ACPI: LAPIC_NMI (acpi_id[0x06] dfl dfl lint[0x1]) [ 0.055418] ACPI: LAPIC_NMI (acpi_id[0x07] dfl dfl lint[0x1]) [ 0.055431] IOAPIC[0]: apic_id 2, version 33, address 0xfec00000, GSI 0-23 [ 0.055434] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) [ 0.055436] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level) [ 0.055441] ACPI: Using ACPI (MADT) for SMP configuration information [ 0.055442] ACPI: HPET id: 0x10b9a201 base: 0xfed00000 [ 0.055452] CPU topo: Max. logical packages: 1 [ 0.055453] CPU topo: Max. logical dies: 1 [ 0.055454] CPU topo: Max. dies per package: 1 [ 0.055459] CPU topo: Max. threads per core: 1 [ 0.055460] CPU topo: Num. cores per package: 8 [ 0.055461] CPU topo: Num. threads per package: 8 [ 0.055462] CPU topo: Allowing 8 present CPUs plus 0 hotplug CPUs [ 0.055475] PM: hibernation: Registered nosave memory: [mem 0x00000000-0x00000fff] [ 0.055477] PM: hibernation: Registered nosave memory: [mem 0x0009f000-0x0009ffff] [ 0.055478] PM: hibernation: Registered nosave memory: [mem 0x000a0000-0x000effff] [ 0.055479] PM: hibernation: Registered nosave memory: [mem 0x000f0000-0x000fffff] [ 0.055481] PM: hibernation: Registered nosave memory: [mem 0xbfdf0000-0xbfdf2fff] [ 0.055482] PM: hibernation: Registered nosave memory: [mem 0xbfdf3000-0xbfdfffff] [ 0.055483] PM: hibernation: Registered nosave memory: [mem 0xbfe00000-0xbfefffff] [ 0.055484] PM: hibernation: Registered nosave memory: [mem 0xbff00000-0xdfffffff] [ 0.055485] PM: hibernation: Registered nosave memory: [mem 0xe0000000-0xefffffff] [ 0.055487] PM: hibernation: Registered nosave memory: [mem 0xf0000000-0xfebfffff] [ 0.055488] PM: hibernation: Registered nosave memory: [mem 0xfec00000-0xffffffff] [ 0.055490] [mem 0xbff00000-0xdfffffff] available for PCI devices [ 0.055491] Booting paravirtualized kernel on bare hardware [ 0.055494] clocksource: refined-jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 6370452778343963 ns [ 0.061413] setup_percpu: NR_CPUS:320 nr_cpumask_bits:8 nr_cpu_ids:8 nr_node_ids:1 [ 0.062339] percpu: Embedded 66 pages/cpu s233472 r8192 d28672 u524288 [ 0.062348] pcpu-alloc: s233472 r8192 d28672 u524288 alloc=1*2097152 [ 0.062351] pcpu-alloc: [0] 0 1 2 3 [0] 4 5 6 7 [ 0.062373] Kernel command line: BOOT_IMAGE=/vmlinuz-linux root=UUID=963daeed-0888-4658-9f17-18bd343dfb2a rw zswap.enabled=0 rootfstype=ext4 loglevel=3 quiet [ 0.062455] Unknown kernel command line parameters "BOOT_IMAGE=/vmlinuz-linux", will be passed to user space. [ 0.065336] Dentry cache hash table entries: 2097152 (order: 12, 16777216 bytes, linear) [ 0.066737] Inode-cache hash table entries: 1048576 (order: 11, 8388608 bytes, linear) [ 0.066821] Fallback order for Node 0: 0 [ 0.066827] Built 1 zonelists, mobility grouping on. Total pages: 4123960 [ 0.066829] Policy zone: Normal [ 0.067262] mem auto-init: stack:all(zero), heap alloc:on, heap free:off [ 0.067268] software IO TLB: area num 8. [ 0.153647] Memory: 16301808K/16758328K available (18432K kernel code, 2164K rwdata, 13296K rodata, 3412K init, 3624K bss, 456260K reserved, 0K cma-reserved) [ 0.161802] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=8, Nodes=1 [ 0.161996] ftrace: allocating 49852 entries in 195 pages [ 0.173225] ftrace: allocated 195 pages with 4 groups [ 0.173386] Dynamic Preempt: full [ 0.173613] rcu: Preemptible hierarchical RCU implementation. [ 0.173614] rcu: RCU restricting CPUs from NR_CPUS=320 to nr_cpu_ids=8. [ 0.173616] rcu: RCU priority boosting: priority 1 delay 500 ms. [ 0.173617] Trampoline variant of Tasks RCU enabled. [ 0.173618] Rude variant of Tasks RCU enabled. [ 0.173619] Tracing variant of Tasks RCU enabled. [ 0.173620] rcu: RCU calculated value of scheduler-enlistment delay is 30 jiffies. [ 0.173621] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=8 [ 0.173629] RCU Tasks: Setting shift to 3 and lim to 1 rcu_task_cb_adjust=1. [ 0.173631] RCU Tasks Rude: Setting shift to 3 and lim to 1 rcu_task_cb_adjust=1. [ 0.173633] RCU Tasks Trace: Setting shift to 3 and lim to 1 rcu_task_cb_adjust=1. [ 0.179214] NR_IRQS: 20736, nr_irqs: 488, preallocated irqs: 16 [ 0.179427] rcu: srcu_init: Setting srcu_struct sizes based on contention. [ 0.179520] kfence: initialized - using 2097152 bytes for 255 objects at 0x(____ptrval____)-0x(____ptrval____) [ 0.179595] spurious 8259A interrupt: IRQ7. [ 0.179615] Console: colour dummy device 80x25 [ 0.179618] printk: legacy console [tty0] enabled [ 0.180017] ACPI: Core revision 20230628 [ 0.180243] clocksource: hpet: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 133484873504 ns [ 0.180277] APIC: Switch to symmetric I/O mode setup [ 0.180782] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1 [ 0.196930] clocksource: tsc-early: mask: 0xffffffffffffffff max_cycles: 0x2fe2839811f, max_idle_ns: 440795276340 ns [ 0.196936] Calibrating delay loop (skipped), value calculated using timer frequency.. 6646.85 BogoMIPS (lpj=11073363) [ 0.196960] LVT offset 1 assigned for vector 0xf9 [ 0.196965] Last level iTLB entries: 4KB 512, 2MB 1024, 4MB 512 [ 0.196967] Last level dTLB entries: 4KB 1024, 2MB 1024, 4MB 512, 1GB 0 [ 0.196972] Spectre V1 : Mitigation: usercopy/swapgs barriers and __user pointer sanitization [ 0.196974] Spectre V2 : Mitigation: Retpolines [ 0.196975] Spectre V2 : Spectre v2 / SpectreRSB mitigation: Filling RSB on context switch [ 0.196976] Spectre V2 : Spectre v2 / SpectreRSB : Filling RSB on VMEXIT [ 0.196977] Spectre V2 : Enabling Speculation Barrier for firmware calls [ 0.196978] RETBleed: Mitigation: untrained return thunk [ 0.196980] Spectre V2 : mitigation: Enabling conditional Indirect Branch Prediction Barrier [ 0.196982] Speculative Store Bypass: Mitigation: Speculative Store Bypass disabled via prctl [ 0.196986] x86/fpu: Supporting XSAVE feature 0x001: 'x87 floating point registers' [ 0.196988] x86/fpu: Supporting XSAVE feature 0x002: 'SSE registers' [ 0.196989] x86/fpu: Supporting XSAVE feature 0x004: 'AVX registers' [ 0.196991] x86/fpu: xstate_offset[2]: 576, xstate_sizes[2]: 256 [ 0.196993] x86/fpu: Enabled xstate features 0x7, context size is 832 bytes, using 'standard' format. [ 0.220801] Freeing SMP alternatives memory: 40K [ 0.220807] pid_max: default: 32768 minimum: 301 [ 0.221538] LSM: initializing lsm=capability,landlock,lockdown,yama,bpf [ 0.222378] landlock: Up and running. [ 0.222380] Yama: becoming mindful. [ 0.222387] LSM support for eBPF active [ 0.222633] Mount-cache hash table entries: 32768 (order: 6, 262144 bytes, linear) [ 0.222673] Mountpoint-cache hash table entries: 32768 (order: 6, 262144 bytes, linear) [ 0.230401] APIC calibration not consistent with PM-Timer: 0ms instead of 100ms [ 0.230407] APIC delta adjusted to PM-Timer: 1257428 (1507) [ 0.230416] smpboot: CPU0: AMD FX(tm)-8300 Eight-Core Processor (family: 0x15, model: 0x2, stepping: 0x0) [ 0.230808] Performance Events: Fam15h core perfctr, AMD PMU driver. [ 0.230814] ... version: 0 [ 0.230815] ... bit width: 48 [ 0.230816] ... generic registers: 6 [ 0.230817] ... value mask: 0000ffffffffffff [ 0.230818] ... max period: 00007fffffffffff [ 0.230819] ... fixed-purpose events: 0 [ 0.230820] ... event mask: 000000000000003f [ 0.230932] signal: max sigframe size: 1776 [ 0.230983] rcu: Hierarchical SRCU implementation. [ 0.230985] rcu: Max phase no-delay instances is 1000. [ 0.233293] MCE: In-kernel MCE decoding enabled. [ 0.233373] NMI watchdog: Enabled. Permanently consumes one hw-PMU counter. [ 0.233505] smp: Bringing up secondary CPUs ... [ 0.233600] smpboot: x86: Booting SMP configuration: [ 0.233600] .... node #0, CPUs: #1 #2 #3 #4 #5 #6 #7 [ 0.000814] __common_interrupt: 1.55 No irq handler for vector [ 0.000814] __common_interrupt: 2.55 No irq handler for vector [ 0.000814] __common_interrupt: 3.55 No irq handler for vector [ 0.000814] __common_interrupt: 4.55 No irq handler for vector [ 0.000814] __common_interrupt: 5.55 No irq handler for vector [ 0.000814] __common_interrupt: 6.55 No irq handler for vector [ 0.000814] __common_interrupt: 7.55 No irq handler for vector [ 0.263642] smp: Brought up 1 node, 8 CPUs [ 0.263647] smpboot: Total of 8 processors activated (53173.81 BogoMIPS) [ 0.270270] devtmpfs: initialized [ 0.270315] x86/mm: Memory block size: 128MB [ 0.272131] ACPI: PM: Registering ACPI NVS region [mem 0xbfdf0000-0xbfdf2fff] (12288 bytes) [ 0.272131] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 6370867519511994 ns [ 0.272131] futex hash table entries: 2048 (order: 5, 131072 bytes, linear) [ 0.272131] pinctrl core: initialized pinctrl subsystem [ 0.272131] PM: RTC time: 12:42:29, date: 2024-05-29 [ 0.272188] NET: Registered PF_NETLINK/PF_ROUTE protocol family [ 0.272620] DMA: preallocated 2048 KiB GFP_KERNEL pool for atomic allocations [ 0.272907] DMA: preallocated 2048 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations [ 0.273800] DMA: preallocated 2048 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations [ 0.273814] audit: initializing netlink subsys (disabled) [ 0.273827] audit: type=2000 audit(1716986548.096:1): state=initialized audit_enabled=0 res=1 [ 0.273827] thermal_sys: Registered thermal governor 'fair_share' [ 0.273827] thermal_sys: Registered thermal governor 'bang_bang' [ 0.273827] thermal_sys: Registered thermal governor 'step_wise' [ 0.273827] thermal_sys: Registered thermal governor 'user_space' [ 0.273827] thermal_sys: Registered thermal governor 'power_allocator' [ 0.273827] cpuidle: using governor ladder [ 0.273827] cpuidle: using governor menu [ 0.273827] acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5 [ 0.274016] PCI: ECAM [mem 0xe0000000-0xefffffff] (base 0xe0000000) for domain 0000 [bus 00-ff] [ 0.274021] PCI: ECAM [mem 0xe0000000-0xefffffff] reserved as E820 entry [ 0.274034] PCI: Using configuration type 1 for base access [ 0.274129] kprobes: kprobe jump-optimization is enabled. All kprobes are optimized if possible. [ 0.277003] HugeTLB: registered 1.00 GiB page size, pre-allocated 0 pages [ 0.277003] HugeTLB: 16380 KiB vmemmap can be freed for a 1.00 GiB page [ 0.277003] HugeTLB: registered 2.00 MiB page size, pre-allocated 0 pages [ 0.277003] HugeTLB: 28 KiB vmemmap can be freed for a 2.00 MiB page [ 0.277018] Demotion targets for Node 0: null [ 0.277135] fbcon: Taking over console [ 0.277135] ACPI: Added _OSI(Module Device) [ 0.277135] ACPI: Added _OSI(Processor Device) [ 0.277135] ACPI: Added _OSI(3.0 _SCP Extensions) [ 0.277135] ACPI: Added _OSI(Processor Aggregator Device) [ 0.281946] ACPI: 2 ACPI AML tables successfully acquired and loaded [ 0.282248] ACPI Error: AE_NOT_FOUND, While resolving a named reference package element - LNKC (20230628/dspkginit-438) [ 0.282255] ACPI Error: AE_NOT_FOUND, While resolving a named reference package element - LNKD (20230628/dspkginit-438) [ 0.282262] ACPI Error: AE_NOT_FOUND, While resolving a named reference package element - LNKA (20230628/dspkginit-438) [ 0.282268] ACPI Error: AE_NOT_FOUND, While resolving a named reference package element - LNKB (20230628/dspkginit-438) [ 0.282281] ACPI Error: AE_NOT_FOUND, While resolving a named reference package element - LNKD (20230628/dspkginit-438) [ 0.282288] ACPI Error: AE_NOT_FOUND, While resolving a named reference package element - LNKA (20230628/dspkginit-438) [ 0.282294] ACPI Error: AE_NOT_FOUND, While resolving a named reference package element - LNKB (20230628/dspkginit-438) [ 0.282300] ACPI Error: AE_NOT_FOUND, While resolving a named reference package element - LNKC (20230628/dspkginit-438) [ 0.282313] ACPI Error: AE_NOT_FOUND, While resolving a named reference package element - LNKA (20230628/dspkginit-438) [ 0.282319] ACPI Error: AE_NOT_FOUND, While resolving a named reference package element - LNKB (20230628/dspkginit-438) [ 0.282325] ACPI Error: AE_NOT_FOUND, While resolving a named reference package element - LNKC (20230628/dspkginit-438) [ 0.282331] ACPI Error: AE_NOT_FOUND, While resolving a named reference package element - LNKD (20230628/dspkginit-438) [ 0.282343] ACPI Error: AE_NOT_FOUND, While resolving a named reference package element - LNKB (20230628/dspkginit-438) [ 0.282349] ACPI Error: AE_NOT_FOUND, While resolving a named reference package element - LNKC (20230628/dspkginit-438) [ 0.282355] ACPI Error: AE_NOT_FOUND, While resolving a named reference package element - LNKD (20230628/dspkginit-438) [ 0.282361] ACPI Error: AE_NOT_FOUND, While resolving a named reference package element - LNKA (20230628/dspkginit-438) [ 0.282374] ACPI Error: AE_NOT_FOUND, While resolving a named reference package element - LNKC (20230628/dspkginit-438) [ 0.282380] ACPI Error: AE_NOT_FOUND, While resolving a named reference package element - LNKD (20230628/dspkginit-438) [ 0.282386] ACPI Error: AE_NOT_FOUND, While resolving a named reference package element - LNKA (20230628/dspkginit-438) [ 0.282392] ACPI Error: AE_NOT_FOUND, While resolving a named reference package element - LNKB (20230628/dspkginit-438) [ 0.282405] ACPI Error: AE_NOT_FOUND, While resolving a named reference package element - LNKD (20230628/dspkginit-438) [ 0.282411] ACPI Error: AE_NOT_FOUND, While resolving a named reference package element - LNKA (20230628/dspkginit-438) [ 0.282417] ACPI Error: AE_NOT_FOUND, While resolving a named reference package element - LNKB (20230628/dspkginit-438) [ 0.282423] ACPI Error: AE_NOT_FOUND, While resolving a named reference package element - LNKC (20230628/dspkginit-438) [ 0.282435] ACPI Error: AE_NOT_FOUND, While resolving a named reference package element - LNKB (20230628/dspkginit-438) [ 0.282441] ACPI Error: AE_NOT_FOUND, While resolving a named reference package element - LNKC (20230628/dspkginit-438) [ 0.282447] ACPI Error: AE_NOT_FOUND, While resolving a named reference package element - LNKD (20230628/dspkginit-438) [ 0.282453] ACPI Error: AE_NOT_FOUND, While resolving a named reference package element - LNKA (20230628/dspkginit-438) [ 0.282465] ACPI Error: AE_NOT_FOUND, While resolving a named reference package element - LNKC (20230628/dspkginit-438) [ 0.282471] ACPI Error: AE_NOT_FOUND, While resolving a named reference package element - LNKD (20230628/dspkginit-438) [ 0.282477] ACPI Error: AE_NOT_FOUND, While resolving a named reference package element - LNKA (20230628/dspkginit-438) [ 0.282482] ACPI Error: AE_NOT_FOUND, While resolving a named reference package element - LNKB (20230628/dspkginit-438) [ 0.282495] ACPI Error: AE_NOT_FOUND, While resolving a named reference package element - LNKD (20230628/dspkginit-438) [ 0.282501] ACPI Error: AE_NOT_FOUND, While resolving a named reference package element - LNKA (20230628/dspkginit-438) [ 0.282507] ACPI Error: AE_NOT_FOUND, While resolving a named reference package element - LNKB (20230628/dspkginit-438) [ 0.282512] ACPI Error: AE_NOT_FOUND, While resolving a named reference package element - LNKC (20230628/dspkginit-438) [ 0.282525] ACPI Error: AE_NOT_FOUND, While resolving a named reference package element - LNKA (20230628/dspkginit-438) [ 0.282531] ACPI Error: AE_NOT_FOUND, While resolving a named reference package element - LNKB (20230628/dspkginit-438) [ 0.282536] ACPI Error: AE_NOT_FOUND, While resolving a named reference package element - LNKC (20230628/dspkginit-438) [ 0.282542] ACPI Error: AE_NOT_FOUND, While resolving a named reference package element - LNKD (20230628/dspkginit-438) [ 0.287045] ACPI: _OSC evaluation for CPUs failed, trying _PDC [ 0.287206] ACPI: Interpreter enabled [ 0.287226] ACPI: PM: (supports S0 S3 S4 S5) [ 0.287228] ACPI: Using IOAPIC for interrupt routing [ 0.287550] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug [ 0.287552] PCI: Using E820 reservations for host bridge windows [ 0.287705] ACPI: Enabled 5 GPEs in block 00 to 1F [ 0.294800] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff]) [ 0.294808] acpi PNP0A03:00: _OSC: OS supports [ExtendedConfig ASPM ClockPM Segments MSI EDR HPX-Type3] [ 0.295182] PCI host bridge to bus 0000:00 [ 0.295184] pci_bus 0000:00: root bus resource [io 0x0000-0x0cf7 window] [ 0.295187] pci_bus 0000:00: root bus resource [io 0x0d00-0xffff window] [ 0.295190] pci_bus 0000:00: root bus resource [mem 0x000a0000-0x000dffff window] [ 0.295192] pci_bus 0000:00: root bus resource [mem 0xc0000000-0xfebfffff window] [ 0.295195] pci_bus 0000:00: root bus resource [bus 00-ff] [ 0.295212] pci 0000:00:00.0: [1022:9600] type 00 class 0x060000 conventional PCI endpoint [ 0.295224] pci 0000:00:00.0: [Firmware Bug]: BAR 3: invalid; can't size [ 0.295301] pci 0000:00:02.0: [1022:9603] type 01 class 0x060400 PCIe Root Port [ 0.295314] pci 0000:00:02.0: PCI bridge to [bus 01] [ 0.295318] pci 0000:00:02.0: bridge window [io 0xe000-0xefff] [ 0.295321] pci 0000:00:02.0: bridge window [mem 0xfb000000-0xfcffffff] [ 0.295327] pci 0000:00:02.0: bridge window [mem 0xc0000000-0xdfffffff 64bit pref] [ 0.295333] pci 0000:00:02.0: enabling Extended Tags [ 0.295361] pci 0000:00:02.0: PME# supported from D0 D3hot D3cold [ 0.295467] pci 0000:00:04.0: [1022:9604] type 01 class 0x060400 PCIe Root Port [ 0.295480] pci 0000:00:04.0: PCI bridge to [bus 02] [ 0.295484] pci 0000:00:04.0: bridge window [io 0xd000-0xdfff] [ 0.295487] pci 0000:00:04.0: bridge window [mem 0xfda00000-0xfdafffff] [ 0.295492] pci 0000:00:04.0: bridge window [mem 0xfdf00000-0xfdffffff 64bit pref] [ 0.295498] pci 0000:00:04.0: enabling Extended Tags [ 0.295524] pci 0000:00:04.0: PME# supported from D0 D3hot D3cold [ 0.295624] pci 0000:00:06.0: [1022:9606] type 01 class 0x060400 PCIe Root Port [ 0.295637] pci 0000:00:06.0: PCI bridge to [bus 03] [ 0.295641] pci 0000:00:06.0: bridge window [io 0xc000-0xcfff] [ 0.295643] pci 0000:00:06.0: bridge window [mem 0xfde00000-0xfdefffff] [ 0.295649] pci 0000:00:06.0: bridge window [mem 0xfdd00000-0xfddfffff 64bit pref] [ 0.295655] pci 0000:00:06.0: enabling Extended Tags [ 0.295681] pci 0000:00:06.0: PME# supported from D0 D3hot D3cold [ 0.295804] pci 0000:00:11.0: [1002:4390] type 00 class 0x01018f conventional PCI endpoint [ 0.295821] pci 0000:00:11.0: BAR 0 [io 0xff00-0xff07] [ 0.295830] pci 0000:00:11.0: BAR 1 [io 0xfe00-0xfe03] [ 0.295840] pci 0000:00:11.0: BAR 2 [io 0xfd00-0xfd07] [ 0.295849] pci 0000:00:11.0: BAR 3 [io 0xfc00-0xfc03] [ 0.295858] pci 0000:00:11.0: BAR 4 [io 0xfb00-0xfb0f] [ 0.295867] pci 0000:00:11.0: BAR 5 [mem 0xfe02f000-0xfe02f3ff] [ 0.295889] pci 0000:00:11.0: set SATA to AHCI mode [ 0.295993] pci 0000:00:12.0: [1002:4397] type 00 class 0x0c0310 conventional PCI endpoint [ 0.296010] pci 0000:00:12.0: BAR 0 [mem 0xfe02e000-0xfe02efff] [ 0.296140] pci 0000:00:12.1: [1002:4398] type 00 class 0x0c0310 conventional PCI endpoint [ 0.296157] pci 0000:00:12.1: BAR 0 [mem 0xfe02d000-0xfe02dfff] [ 0.296297] pci 0000:00:12.2: [1002:4396] type 00 class 0x0c0320 conventional PCI endpoint [ 0.296314] pci 0000:00:12.2: BAR 0 [mem 0xfe02c000-0xfe02c0ff] [ 0.296393] pci 0000:00:12.2: supports D1 D2 [ 0.296395] pci 0000:00:12.2: PME# supported from D0 D1 D2 D3hot [ 0.296483] pci 0000:00:13.0: [1002:4397] type 00 class 0x0c0310 conventional PCI endpoint [ 0.296500] pci 0000:00:13.0: BAR 0 [mem 0xfe02b000-0xfe02bfff] [ 0.296627] pci 0000:00:13.1: [1002:4398] type 00 class 0x0c0310 conventional PCI endpoint [ 0.296643] pci 0000:00:13.1: BAR 0 [mem 0xfe02a000-0xfe02afff] [ 0.296776] pci 0000:00:13.2: [1002:4396] type 00 class 0x0c0320 conventional PCI endpoint [ 0.296793] pci 0000:00:13.2: BAR 0 [mem 0xfe029000-0xfe0290ff] [ 0.296872] pci 0000:00:13.2: supports D1 D2 [ 0.296874] pci 0000:00:13.2: PME# supported from D0 D1 D2 D3hot [ 0.296974] pci 0000:00:14.0: [1002:4385] type 00 class 0x0c0500 conventional PCI endpoint [ 0.297129] pci 0000:00:14.1: [1002:439c] type 00 class 0x01018a conventional PCI endpoint [ 0.297146] pci 0000:00:14.1: BAR 0 [io 0x0000-0x0007] [ 0.297155] pci 0000:00:14.1: BAR 1 [io 0x0000-0x0003] [ 0.297164] pci 0000:00:14.1: BAR 2 [io 0x0000-0x0007] [ 0.297173] pci 0000:00:14.1: BAR 3 [io 0x0000-0x0003] [ 0.297182] pci 0000:00:14.1: BAR 4 [io 0xfa00-0xfa0f] [ 0.297202] pci 0000:00:14.1: BAR 0 [io 0x01f0-0x01f7]: legacy IDE quirk [ 0.297204] pci 0000:00:14.1: BAR 1 [io 0x03f6]: legacy IDE quirk [ 0.297206] pci 0000:00:14.1: BAR 2 [io 0x0170-0x0177]: legacy IDE quirk [ 0.297207] pci 0000:00:14.1: BAR 3 [io 0x0376]: legacy IDE quirk [ 0.297315] pci 0000:00:14.2: [1002:4383] type 00 class 0x040300 conventional PCI endpoint [ 0.297336] pci 0000:00:14.2: BAR 0 [mem 0xfe024000-0xfe027fff 64bit] [ 0.297403] pci 0000:00:14.2: PME# supported from D0 D3hot D3cold [ 0.297482] pci 0000:00:14.3: [1002:439d] type 00 class 0x060100 conventional PCI endpoint [ 0.297648] pci 0000:00:14.4: [1002:4384] type 01 class 0x060401 conventional PCI bridge [ 0.297679] pci 0000:00:14.4: PCI bridge to [bus 04] (subtractive decode) [ 0.297685] pci 0000:00:14.4: bridge window [io 0xb000-0xbfff] [ 0.297689] pci 0000:00:14.4: bridge window [mem 0xfdc00000-0xfdcfffff] [ 0.297694] pci 0000:00:14.4: bridge window [mem 0xfdb00000-0xfdbfffff pref] [ 0.297779] pci 0000:00:14.5: [1002:4399] type 00 class 0x0c0310 conventional PCI endpoint [ 0.297796] pci 0000:00:14.5: BAR 0 [mem 0xfe028000-0xfe028fff] [ 0.297926] pci 0000:00:18.0: [1022:1600] type 00 class 0x060000 conventional PCI endpoint [ 0.297976] pci 0000:00:18.1: [1022:1601] type 00 class 0x060000 conventional PCI endpoint [ 0.298023] pci 0000:00:18.2: [1022:1602] type 00 class 0x060000 conventional PCI endpoint [ 0.298073] pci 0000:00:18.3: [1022:1603] type 00 class 0x060000 conventional PCI endpoint [ 0.298121] pci 0000:00:18.4: [1022:1604] type 00 class 0x060000 conventional PCI endpoint [ 0.298170] pci 0000:00:18.5: [1022:1605] type 00 class 0x060000 conventional PCI endpoint [ 0.298277] pci 0000:01:00.0: [10de:1c82] type 00 class 0x030000 PCIe Legacy Endpoint [ 0.298291] pci 0000:01:00.0: BAR 0 [mem 0xfb000000-0xfbffffff] [ 0.298302] pci 0000:01:00.0: BAR 1 [mem 0xc0000000-0xcfffffff 64bit pref] [ 0.298313] pci 0000:01:00.0: BAR 3 [mem 0xde000000-0xdfffffff 64bit pref] [ 0.298320] pci 0000:01:00.0: BAR 5 [io 0xef00-0xef7f] [ 0.298328] pci 0000:01:00.0: ROM [mem 0x00000000-0x0007ffff pref] [ 0.298355] pci 0000:01:00.0: Video device with shadowed ROM at [mem 0x000c0000-0x000dffff] [ 0.298444] pci 0000:01:00.0: 32.000 Gb/s available PCIe bandwidth, limited by 2.5 GT/s PCIe x16 link at 0000:00:02.0 (capable of 126.016 Gb/s with 8.0 GT/s PCIe x16 link) [ 0.298520] pci 0000:01:00.1: [10de:0fb9] type 00 class 0x040300 PCIe Endpoint [ 0.298533] pci 0000:01:00.1: BAR 0 [mem 0xfcffc000-0xfcffffff] [ 0.298683] pci 0000:00:02.0: PCI bridge to [bus 01] [ 0.298724] pci 0000:02:00.0: [1106:3483] type 00 class 0x0c0330 PCIe Endpoint [ 0.298739] pci 0000:02:00.0: BAR 0 [mem 0xfdaff000-0xfdafffff 64bit] [ 0.298800] pci 0000:02:00.0: PME# supported from D0 D1 D2 D3hot D3cold [ 0.298870] pci 0000:00:04.0: PCI bridge to [bus 02] [ 0.298918] pci 0000:03:00.0: [10ec:8168] type 00 class 0x020000 PCIe Endpoint [ 0.298934] pci 0000:03:00.0: BAR 0 [io 0xce00-0xceff] [ 0.298954] pci 0000:03:00.0: BAR 2 [mem 0xfdeff000-0xfdefffff 64bit] [ 0.298967] pci 0000:03:00.0: BAR 4 [mem 0xfddfc000-0xfddfffff 64bit pref] [ 0.299049] pci 0000:03:00.0: supports D1 D2 [ 0.299051] pci 0000:03:00.0: PME# supported from D0 D1 D2 D3hot D3cold [ 0.299175] pci 0000:00:06.0: PCI bridge to [bus 03] [ 0.299190] pci_bus 0000:04: extended config space not accessible [ 0.299252] pci 0000:00:14.4: PCI bridge to [bus 04] (subtractive decode) [ 0.299261] pci 0000:00:14.4: bridge window [io 0x0000-0x0cf7 window] (subtractive decode) [ 0.299263] pci 0000:00:14.4: bridge window [io 0x0d00-0xffff window] (subtractive decode) [ 0.299265] pci 0000:00:14.4: bridge window [mem 0x000a0000-0x000dffff window] (subtractive decode) [ 0.299267] pci 0000:00:14.4: bridge window [mem 0xc0000000-0xfebfffff window] (subtractive decode) [ 0.299551] ACPI: PCI: Interrupt link LNKA configured for IRQ 0 [ 0.299553] ACPI: PCI: Interrupt link LNKA disabled [ 0.299609] ACPI: PCI: Interrupt link LNKB configured for IRQ 0 [ 0.299611] ACPI: PCI: Interrupt link LNKB disabled [ 0.299666] ACPI: PCI: Interrupt link LNKC configured for IRQ 0 [ 0.299668] ACPI: PCI: Interrupt link LNKC disabled [ 0.299722] ACPI: PCI: Interrupt link LNKD configured for IRQ 0 [ 0.299723] ACPI: PCI: Interrupt link LNKD disabled [ 0.299777] ACPI: PCI: Interrupt link LNKE configured for IRQ 0 [ 0.299779] ACPI: PCI: Interrupt link LNKE disabled [ 0.299832] ACPI: PCI: Interrupt link LNKF configured for IRQ 0 [ 0.299834] ACPI: PCI: Interrupt link LNKF disabled [ 0.299887] ACPI: PCI: Interrupt link LNK0 configured for IRQ 0 [ 0.299889] ACPI: PCI: Interrupt link LNK0 disabled [ 0.299942] ACPI: PCI: Interrupt link LNK1 configured for IRQ 0 [ 0.299944] ACPI: PCI: Interrupt link LNK1 disabled [ 0.300718] iommu: Default domain type: Translated [ 0.300718] iommu: DMA domain TLB invalidation policy: lazy mode [ 0.300718] SCSI subsystem initialized [ 0.300718] libata version 3.00 loaded. [ 0.300718] ACPI: bus type USB registered [ 0.300718] usbcore: registered new interface driver usbfs [ 0.300718] usbcore: registered new interface driver hub [ 0.300718] usbcore: registered new device driver usb [ 0.300718] EDAC MC: Ver: 3.0.0 [ 0.300718] NetLabel: Initializing [ 0.300718] NetLabel: domain hash size = 128 [ 0.300718] NetLabel: protocols = UNLABELED CIPSOv4 CALIPSO [ 0.300718] NetLabel: unlabeled traffic allowed by default [ 0.300718] mctp: management component transport protocol core [ 0.300718] NET: Registered PF_MCTP protocol family [ 0.300718] PCI: Using ACPI for IRQ routing [ 0.310072] PCI: pci_cache_line_size set to 64 bytes [ 0.310124] e820: reserve RAM buffer [mem 0x0009f800-0x0009ffff] [ 0.310127] e820: reserve RAM buffer [mem 0xbfdf0000-0xbfffffff] [ 0.310128] e820: reserve RAM buffer [mem 0x43f000000-0x43fffffff] [ 0.310315] pci 0000:01:00.0: vgaarb: setting as boot VGA device [ 0.310315] pci 0000:01:00.0: vgaarb: bridge control possible [ 0.310315] pci 0000:01:00.0: vgaarb: VGA device added: decodes=io+mem,owns=io+mem,locks=none [ 0.310315] vgaarb: loaded [ 0.310317] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0, 0 [ 0.310317] hpet0: 4 comparators, 32-bit 14.318180 MHz counter [ 0.313604] clocksource: Switched to clocksource tsc-early [ 0.313620] VFS: Disk quotas dquot_6.6.0 [ 0.313620] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes) [ 0.313620] pnp: PnP ACPI init [ 0.313620] system 00:00: [io 0x04d0-0x04d1] has been reserved [ 0.313620] system 00:00: [io 0x0220-0x0225] has been reserved [ 0.313620] system 00:00: [io 0x0290-0x0294] has been reserved [ 0.314919] system 00:01: [io 0x4100-0x411f] has been reserved [ 0.314927] system 00:01: [io 0x0228-0x022f] has been reserved [ 0.314929] system 00:01: [io 0x040b] has been reserved [ 0.314931] system 00:01: [io 0x04d6] has been reserved [ 0.314934] system 00:01: [io 0x0c00-0x0c01] has been reserved [ 0.314936] system 00:01: [io 0x0c14] has been reserved [ 0.314938] system 00:01: [io 0x0c50-0x0c52] has been reserved [ 0.314940] system 00:01: [io 0x0c6c-0x0c6d] has been reserved [ 0.314941] system 00:01: [io 0x0c6f] has been reserved [ 0.314943] system 00:01: [io 0x0cd0-0x0cd1] has been reserved [ 0.314945] system 00:01: [io 0x0cd2-0x0cd3] has been reserved [ 0.314947] system 00:01: [io 0x0cd4-0x0cdf] has been reserved [ 0.314949] system 00:01: [io 0x4000-0x40fe] has been reserved [ 0.314951] system 00:01: [io 0x4210-0x4217] has been reserved [ 0.314952] system 00:01: [io 0x0b00-0x0b0f] has been reserved [ 0.314954] system 00:01: [io 0x0b10-0x0b1f] has been reserved [ 0.314956] system 00:01: [io 0x0b20-0x0b3f] has been reserved [ 0.314958] system 00:01: [mem 0x00000000-0x00000fff window] could not be reserved [ 0.314961] system 00:01: [mem 0xfee00400-0xfee00fff window] has been reserved [ 0.315981] system 00:05: [mem 0xe0000000-0xefffffff] has been reserved [ 0.316207] pnp 00:06: disabling [mem 0x000ce600-0x000cffff] because it overlaps 0000:01:00.0 BAR 6 [mem 0x000c0000-0x000dffff] [ 0.316230] system 00:06: [mem 0x000f0000-0x000f7fff] could not be reserved [ 0.316232] system 00:06: [mem 0x000f8000-0x000fbfff] could not be reserved [ 0.316235] system 00:06: [mem 0x000fc000-0x000fffff] could not be reserved [ 0.316237] system 00:06: [mem 0xbfdf0000-0xbfdfffff] could not be reserved [ 0.316239] system 00:06: [mem 0xffff0000-0xffffffff] has been reserved [ 0.316241] system 00:06: [mem 0x00000000-0x0009ffff] could not be reserved [ 0.316243] system 00:06: [mem 0x00100000-0xbfdeffff] could not be reserved [ 0.316246] system 00:06: [mem 0xbfe00000-0xbfefffff] has been reserved [ 0.316248] system 00:06: [mem 0xbff00000-0xbfffffff] could not be reserved [ 0.316250] system 00:06: [mem 0xfec00000-0xfec00fff] could not be reserved [ 0.316252] system 00:06: [mem 0xfee00000-0xfee00fff] could not be reserved [ 0.316254] system 00:06: [mem 0xfff80000-0xfffeffff] has been reserved [ 0.316278] pnp: PnP ACPI: found 7 devices [ 0.322952] clocksource: acpi_pm: mask: 0xffffff max_cycles: 0xffffff, max_idle_ns: 2085701024 ns [ 0.323236] NET: Registered PF_INET protocol family [ 0.323560] IP idents hash table entries: 262144 (order: 9, 2097152 bytes, linear) [ 0.341101] tcp_listen_portaddr_hash hash table entries: 8192 (order: 5, 131072 bytes, linear) [ 0.341146] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 0.341306] TCP established hash table entries: 131072 (order: 8, 1048576 bytes, linear) [ 0.341785] TCP bind hash table entries: 65536 (order: 9, 2097152 bytes, linear) [ 0.342107] TCP: Hash tables configured (established 131072 bind 65536) [ 0.342329] MPTCP token hash table entries: 16384 (order: 6, 393216 bytes, linear) [ 0.342432] UDP hash table entries: 8192 (order: 6, 262144 bytes, linear) [ 0.342495] UDP-Lite hash table entries: 8192 (order: 6, 262144 bytes, linear) [ 0.342592] NET: Registered PF_UNIX/PF_LOCAL protocol family [ 0.342609] NET: Registered PF_XDP protocol family [ 0.342625] pci 0000:00:02.0: PCI bridge to [bus 01] [ 0.342634] pci 0000:00:02.0: bridge window [io 0xe000-0xefff] [ 0.342638] pci 0000:00:02.0: bridge window [mem 0xfb000000-0xfcffffff] [ 0.342641] pci 0000:00:02.0: bridge window [mem 0xc0000000-0xdfffffff 64bit pref] [ 0.342645] pci 0000:00:04.0: PCI bridge to [bus 02] [ 0.342648] pci 0000:00:04.0: bridge window [io 0xd000-0xdfff] [ 0.342651] pci 0000:00:04.0: bridge window [mem 0xfda00000-0xfdafffff] [ 0.342653] pci 0000:00:04.0: bridge window [mem 0xfdf00000-0xfdffffff 64bit pref] [ 0.342657] pci 0000:00:06.0: PCI bridge to [bus 03] [ 0.342659] pci 0000:00:06.0: bridge window [io 0xc000-0xcfff] [ 0.342662] pci 0000:00:06.0: bridge window [mem 0xfde00000-0xfdefffff] [ 0.342665] pci 0000:00:06.0: bridge window [mem 0xfdd00000-0xfddfffff 64bit pref] [ 0.342669] pci 0000:00:14.4: PCI bridge to [bus 04] [ 0.342672] pci 0000:00:14.4: bridge window [io 0xb000-0xbfff] [ 0.342677] pci 0000:00:14.4: bridge window [mem 0xfdc00000-0xfdcfffff] [ 0.342681] pci 0000:00:14.4: bridge window [mem 0xfdb00000-0xfdbfffff pref] [ 0.342688] pci_bus 0000:00: resource 4 [io 0x0000-0x0cf7 window] [ 0.342691] pci_bus 0000:00: resource 5 [io 0x0d00-0xffff window] [ 0.342693] pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000dffff window] [ 0.342695] pci_bus 0000:00: resource 7 [mem 0xc0000000-0xfebfffff window] [ 0.342697] pci_bus 0000:01: resource 0 [io 0xe000-0xefff] [ 0.342699] pci_bus 0000:01: resource 1 [mem 0xfb000000-0xfcffffff] [ 0.342701] pci_bus 0000:01: resource 2 [mem 0xc0000000-0xdfffffff 64bit pref] [ 0.342703] pci_bus 0000:02: resource 0 [io 0xd000-0xdfff] [ 0.342705] pci_bus 0000:02: resource 1 [mem 0xfda00000-0xfdafffff] [ 0.342707] pci_bus 0000:02: resource 2 [mem 0xfdf00000-0xfdffffff 64bit pref] [ 0.342709] pci_bus 0000:03: resource 0 [io 0xc000-0xcfff] [ 0.342711] pci_bus 0000:03: resource 1 [mem 0xfde00000-0xfdefffff] [ 0.342713] pci_bus 0000:03: resource 2 [mem 0xfdd00000-0xfddfffff 64bit pref] [ 0.342715] pci_bus 0000:04: resource 0 [io 0xb000-0xbfff] [ 0.342716] pci_bus 0000:04: resource 1 [mem 0xfdc00000-0xfdcfffff] [ 0.342718] pci_bus 0000:04: resource 2 [mem 0xfdb00000-0xfdbfffff pref] [ 0.342720] pci_bus 0000:04: resource 4 [io 0x0000-0x0cf7 window] [ 0.342722] pci_bus 0000:04: resource 5 [io 0x0d00-0xffff window] [ 0.342724] pci_bus 0000:04: resource 6 [mem 0x000a0000-0x000dffff window] [ 0.342725] pci_bus 0000:04: resource 7 [mem 0xc0000000-0xfebfffff window] [ 0.361533] pci 0000:00:12.0: quirk_usb_early_handoff+0x0/0x730 took 18301 usecs [ 0.378188] pci 0000:00:12.1: quirk_usb_early_handoff+0x0/0x730 took 16251 usecs [ 0.394839] pci 0000:00:13.0: quirk_usb_early_handoff+0x0/0x730 took 16052 usecs [ 0.411492] pci 0000:00:13.1: quirk_usb_early_handoff+0x0/0x730 took 16252 usecs [ 0.428146] pci 0000:00:14.5: quirk_usb_early_handoff+0x0/0x730 took 16044 usecs [ 0.428177] pci 0000:01:00.1: extending delay after power-on from D3hot to 20 msec [ 0.428212] pci 0000:01:00.1: D0 power state depends on 0000:01:00.0 [ 0.428421] PCI: CLS 64 bytes, default 64 [ 0.428434] PCI-DMA: Using software bounce buffering for IO (SWIOTLB) [ 0.428436] software IO TLB: mapped [mem 0x00000000bbdf0000-0x00000000bfdf0000] (64MB) [ 0.428477] LVT offset 0 assigned for vector 0x400 [ 0.428514] Trying to unpack rootfs image as initramfs... [ 0.433810] perf: AMD IBS detected (0x000000ff) [ 0.435368] Initialise system trusted keyrings [ 0.435382] Key type blacklist registered [ 0.435423] workingset: timestamp_bits=41 max_order=22 bucket_order=0 [ 0.435432] zbud: loaded [ 0.435825] fuse: init (API version 7.40) [ 0.436328] integrity: Platform Keyring initialized [ 0.436335] integrity: Machine keyring initialized [ 0.451147] Key type asymmetric registered [ 0.451149] Asymmetric key parser 'x509' registered [ 0.451237] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246) [ 0.451317] io scheduler mq-deadline registered [ 0.451320] io scheduler kyber registered [ 0.451386] io scheduler bfq registered [ 0.452277] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4 [ 0.452401] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input0 [ 0.452438] ACPI: button: Power Button [PWRB] [ 0.452491] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input1 [ 0.455780] ACPI: button: Power Button [PWRF] [ 0.455827] ACPI: \_PR_.C000: Found 2 idle states [ 0.455903] ACPI: \_PR_.C001: Found 2 idle states [ 0.455974] ACPI: \_PR_.C002: Found 2 idle states [ 0.456038] ACPI: \_PR_.C003: Found 2 idle states [ 0.456103] ACPI: \_PR_.C004: Found 2 idle states [ 0.456167] ACPI: \_PR_.C005: Found 2 idle states [ 0.456230] ACPI: \_PR_.C006: Found 2 idle states [ 0.456293] ACPI: \_PR_.C007: Found 2 idle states [ 0.456574] Serial: 8250/16550 driver, 32 ports, IRQ sharing enabled [ 0.456760] 00:03: ttyS0 at I/O 0x3f8 (irq = 4, base_baud = 115200) is a 16550A [ 0.459791] Non-volatile memory driver v1.3 [ 0.459793] Linux agpgart interface v0.103 [ 0.459841] ACPI: bus type drm_connector registered [ 0.460708] ahci 0000:00:11.0: version 3.0 [ 0.460951] ahci 0000:00:11.0: AHCI vers 0001.0100, 32 command slots, 3 Gbps, SATA mode [ 0.460955] ahci 0000:00:11.0: 4/4 ports implemented (port mask 0xf) [ 0.460958] ahci 0000:00:11.0: flags: 64bit ncq sntf ilck pm led clo pmp pio slum part ccc [ 0.461546] scsi host0: ahci [ 0.461736] scsi host1: ahci [ 0.461867] scsi host2: ahci [ 0.461987] scsi host3: ahci [ 0.462034] ata1: SATA max UDMA/133 abar m1024@0xfe02f000 port 0xfe02f100 irq 22 lpm-pol 3 [ 0.462037] ata2: SATA max UDMA/133 abar m1024@0xfe02f000 port 0xfe02f180 irq 22 lpm-pol 3 [ 0.462040] ata3: SATA max UDMA/133 abar m1024@0xfe02f000 port 0xfe02f200 irq 22 lpm-pol 3 [ 0.462043] ata4: SATA max UDMA/133 abar m1024@0xfe02f000 port 0xfe02f280 irq 22 lpm-pol 3 [ 0.462257] ohci-pci 0000:00:12.0: OHCI PCI host controller [ 0.462263] ohci-pci 0000:00:12.0: new USB bus registered, assigned bus number 1 [ 0.462305] ohci-pci 0000:00:12.0: irq 16, io mem 0xfe02e000 [ 0.520463] usb usb1: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 6.09 [ 0.520470] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 0.520473] usb usb1: Product: OHCI PCI host controller [ 0.520475] usb usb1: Manufacturer: Linux 6.9.2-arch1-1.3 ohci_hcd [ 0.520477] usb usb1: SerialNumber: 0000:00:12.0 [ 0.520657] hub 1-0:1.0: USB hub found [ 0.520669] hub 1-0:1.0: 3 ports detected [ 0.520900] ehci-pci 0000:00:12.2: EHCI Host Controller [ 0.520907] ehci-pci 0000:00:12.2: new USB bus registered, assigned bus number 2 [ 0.520912] ehci-pci 0000:00:12.2: applying AMD SB700/SB800/Hudson-2/3 EHCI dummy qh workaround [ 0.520923] ehci-pci 0000:00:12.2: debug port 1 [ 0.520989] ehci-pci 0000:00:12.2: irq 17, io mem 0xfe02c000 [ 0.528005] Freeing initrd memory: 50848K [ 0.533015] ehci-pci 0000:00:12.2: USB 2.0 started, EHCI 1.00 [ 0.533088] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.09 [ 0.533091] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 0.533094] usb usb2: Product: EHCI Host Controller [ 0.533096] usb usb2: Manufacturer: Linux 6.9.2-arch1-1.3 ehci_hcd [ 0.533097] usb usb2: SerialNumber: 0000:00:12.2 [ 0.533252] hub 2-0:1.0: USB hub found [ 0.533261] hub 2-0:1.0: 6 ports detected [ 0.599674] hub 1-0:1.0: USB hub found [ 0.599686] hub 1-0:1.0: 3 ports detected [ 0.599839] ehci-pci 0000:00:13.2: EHCI Host Controller [ 0.599845] ehci-pci 0000:00:13.2: new USB bus registered, assigned bus number 3 [ 0.599849] ehci-pci 0000:00:13.2: applying AMD SB700/SB800/Hudson-2/3 EHCI dummy qh workaround [ 0.599866] ehci-pci 0000:00:13.2: debug port 1 [ 0.599919] ehci-pci 0000:00:13.2: irq 19, io mem 0xfe029000 [ 0.612952] ehci-pci 0000:00:13.2: USB 2.0 started, EHCI 1.00 [ 0.613009] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.09 [ 0.613013] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 0.613015] usb usb3: Product: EHCI Host Controller [ 0.613017] usb usb3: Manufacturer: Linux 6.9.2-arch1-1.3 ehci_hcd [ 0.613019] usb usb3: SerialNumber: 0000:00:13.2 [ 0.613140] hub 3-0:1.0: USB hub found [ 0.613148] hub 3-0:1.0: 6 ports detected [ 0.613330] ohci-pci 0000:00:12.1: OHCI PCI host controller [ 0.613334] ohci-pci 0000:00:12.1: new USB bus registered, assigned bus number 4 [ 0.613352] ohci-pci 0000:00:12.1: irq 16, io mem 0xfe02d000 [ 0.673662] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 6.09 [ 0.673667] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 0.673669] usb usb4: Product: OHCI PCI host controller [ 0.673671] usb usb4: Manufacturer: Linux 6.9.2-arch1-1.3 ohci_hcd [ 0.673673] usb usb4: SerialNumber: 0000:00:12.1 [ 0.673843] hub 4-0:1.0: USB hub found [ 0.673854] hub 4-0:1.0: 3 ports detected [ 0.674209] ohci-pci 0000:00:13.0: OHCI PCI host controller [ 0.674217] ohci-pci 0000:00:13.0: new USB bus registered, assigned bus number 5 [ 0.674260] ohci-pci 0000:00:13.0: irq 18, io mem 0xfe02b000 [ 0.733607] usb usb5: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 6.09 [ 0.733611] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 0.733614] usb usb5: Product: OHCI PCI host controller [ 0.733616] usb usb5: Manufacturer: Linux 6.9.2-arch1-1.3 ohci_hcd [ 0.733617] usb usb5: SerialNumber: 0000:00:13.0 [ 0.733795] hub 5-0:1.0: USB hub found [ 0.733805] hub 5-0:1.0: 3 ports detected [ 0.734126] ohci-pci 0000:00:13.1: OHCI PCI host controller [ 0.734132] ohci-pci 0000:00:13.1: new USB bus registered, assigned bus number 6 [ 0.734155] ohci-pci 0000:00:13.1: irq 18, io mem 0xfe02a000 [ 0.777835] ata4: SATA link down (SStatus 0 SControl 300) [ 0.778006] ata1: SATA link down (SStatus 0 SControl 300) [ 0.784485] usb 2-1: new high-speed USB device number 2 using ehci-pci [ 0.793557] usb usb6: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 6.09 [ 0.793561] usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 0.793563] usb usb6: Product: OHCI PCI host controller [ 0.793565] usb usb6: Manufacturer: Linux 6.9.2-arch1-1.3 ohci_hcd [ 0.793566] usb usb6: SerialNumber: 0000:00:13.1 [ 0.793784] hub 6-0:1.0: USB hub found [ 0.793794] hub 6-0:1.0: 3 ports detected [ 0.794124] ohci-pci 0000:00:14.5: OHCI PCI host controller [ 0.794130] ohci-pci 0000:00:14.5: new USB bus registered, assigned bus number 7 [ 0.794149] ohci-pci 0000:00:14.5: irq 18, io mem 0xfe028000 [ 0.853510] usb usb7: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 6.09 [ 0.853514] usb usb7: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 0.853516] usb usb7: Product: OHCI PCI host controller [ 0.853518] usb usb7: Manufacturer: Linux 6.9.2-arch1-1.3 ohci_hcd [ 0.853519] usb usb7: SerialNumber: 0000:00:14.5 [ 0.853737] hub 7-0:1.0: USB hub found [ 0.853747] hub 7-0:1.0: 2 ports detected [ 0.853995] usbcore: registered new interface driver usbserial_generic [ 0.854003] usbserial: USB Serial support registered for generic [ 0.854106] rtc_cmos 00:02: RTC can wake from S4 [ 0.854346] rtc_cmos 00:02: registered as rtc0 [ 0.854374] rtc_cmos 00:02: setting system clock to 2024-05-29T12:42:30 UTC (1716986550) [ 0.854408] rtc_cmos 00:02: alarms up to one month, 242 bytes nvram, hpet irqs [ 0.854453] amd_pstate: the _CPC object is not present in SBIOS or ACPI disabled [ 0.854657] ledtrig-cpu: registered to indicate activity on CPUs [ 0.855141] [drm] Initialized simpledrm 1.0.0 20200625 for simple-framebuffer.0 on minor 0 [ 0.860055] Console: switching to colour frame buffer device 160x64 [ 0.863471] simple-framebuffer simple-framebuffer.0: [drm] fb0: simpledrmdrmfb frame buffer device [ 0.863541] hid: raw HID events driver (C) Jiri Kosina [ 0.863645] drop_monitor: Initializing network drop monitor service [ 0.863986] NET: Registered PF_INET6 protocol family [ 0.871573] Segment Routing with IPv6 [ 0.871576] RPL Segment Routing with IPv6 [ 0.871596] In-situ OAM (IOAM) with IPv6 [ 0.871637] NET: Registered PF_PACKET protocol family [ 0.871698] x86/pm: family 0x15 cpu detected, MSR saving is needed during suspending. [ 0.872216] microcode: Current revision: 0x06000852 [ 0.872218] microcode: Updated early from: 0x06000822 [ 0.872363] IPI shorthand broadcast: enabled [ 0.875084] sched_clock: Marking stable (875210984, -2518685)->(1777722556, -905030257) [ 0.875272] Timer migration: 1 hierarchy levels; 8 children per group; 1 crossnode level [ 0.875373] registered taskstats version 1 [ 0.875705] Loading compiled-in X.509 certificates [ 0.880257] Loaded X.509 cert 'Build time autogenerated kernel key: 792580fa945f304d2a9a419b9cee8195831e651e' [ 0.882915] Key type .fscrypt registered [ 0.882917] Key type fscrypt-provisioning registered [ 0.883423] PM: Magic number: 8:131:735 [ 0.887139] RAS: Correctable Errors collector initialized. [ 0.900662] clk: Disabling unused clocks [ 0.900666] PM: genpd: Disabling unused power domains [ 0.932113] usb 2-1: New USB device found, idVendor=0bda, idProduct=b812, bcdDevice= 2.10 [ 0.932119] usb 2-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 0.932121] usb 2-1: Product: USB3.0 802.11ac 1200M Adapter [ 0.932123] usb 2-1: Manufacturer: Realtek [ 0.932124] usb 2-1: SerialNumber: 123456 [ 0.941464] ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 0.942251] ata3.00: ATA-8: TOSHIBA HDWD110, MS2OA8J0, max UDMA/133 [ 0.942490] ata3.00: 1953525168 sectors, multi 16: LBA48 NCQ (depth 32), AA [ 0.943452] ata3.00: configured for UDMA/133 [ 0.944601] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 0.944732] ata2.00: LPM support broken, forcing max_power [ 0.944760] ata2.00: ATA-11: Apacer AS340 120GB, AP612PE0, max UDMA/133 [ 0.944790] ata2.00: 234441648 sectors, multi 16: LBA48 NCQ (depth 32), AA [ 0.945126] ata2.00: LPM support broken, forcing max_power [ 0.945429] ata2.00: configured for UDMA/133 [ 0.958193] scsi 1:0:0:0: Direct-Access ATA Apacer AS340 120 2PE0 PQ: 0 ANSI: 5 [ 0.958598] sd 1:0:0:0: [sda] 234441648 512-byte logical blocks: (120 GB/112 GiB) [ 0.958602] scsi 2:0:0:0: Direct-Access ATA TOSHIBA HDWD110 A8J0 PQ: 0 ANSI: 5 [ 0.958611] sd 1:0:0:0: [sda] Write Protect is off [ 0.958614] sd 1:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 0.958630] sd 1:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 0.958661] sd 1:0:0:0: [sda] Preferred minimum I/O size 512 bytes [ 0.958942] sd 2:0:0:0: [sdb] 1953525168 512-byte logical blocks: (1.00 TB/932 GiB) [ 0.958945] sd 2:0:0:0: [sdb] 4096-byte physical blocks [ 0.958956] sd 2:0:0:0: [sdb] Write Protect is off [ 0.958958] sd 2:0:0:0: [sdb] Mode Sense: 00 3a 00 00 [ 0.958977] sd 2:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 0.959011] sd 2:0:0:0: [sdb] Preferred minimum I/O size 4096 bytes [ 0.959334] sda: sda1 sda2 [ 0.959434] sd 1:0:0:0: [sda] Attached SCSI disk [ 0.985590] sdb: sdb1 sdb2 [ 0.985834] sd 2:0:0:0: [sdb] Attached SCSI disk [ 0.987971] Freeing unused decrypted memory: 2028K [ 0.988653] Freeing unused kernel image (initmem) memory: 3412K [ 0.988657] Write protecting the kernel read-only data: 32768k [ 0.989141] Freeing unused kernel image (rodata/data gap) memory: 1040K [ 1.032417] x86/mm: Checked W+X mappings: passed, no W+X pages found. [ 1.032421] rodata_test: all tests were successful [ 1.032425] Run /init as init process [ 1.032427] with arguments: [ 1.032428] /init [ 1.032429] with environment: [ 1.032430] HOME=/ [ 1.032431] TERM=linux [ 1.032432] BOOT_IMAGE=/vmlinuz-linux [ 1.200858] xhci_hcd 0000:02:00.0: xHCI Host Controller [ 1.200869] xhci_hcd 0000:02:00.0: new USB bus registered, assigned bus number 8 [ 1.200961] xhci_hcd 0000:02:00.0: hcc params 0x002841eb hci version 0x100 quirks 0x0000000000000890 [ 1.201144] xhci_hcd 0000:02:00.0: xHCI Host Controller [ 1.201149] xhci_hcd 0000:02:00.0: new USB bus registered, assigned bus number 9 [ 1.201153] xhci_hcd 0000:02:00.0: Host supports USB 3.0 SuperSpeed [ 1.201247] scsi host4: pata_atiixp [ 1.201335] usb usb8: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.09 [ 1.201339] usb usb8: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.201342] usb usb8: Product: xHCI Host Controller [ 1.201358] usb usb8: Manufacturer: Linux 6.9.2-arch1-1.3 xhci-hcd [ 1.201361] usb usb8: SerialNumber: 0000:02:00.0 [ 1.201406] scsi host5: pata_atiixp [ 1.201452] ata5: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0xfa00 irq 14 lpm-pol 0 [ 1.201455] ata6: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0xfa08 irq 15 lpm-pol 0 [ 1.201679] hub 8-0:1.0: USB hub found [ 1.201691] hub 8-0:1.0: 1 port detected [ 1.201851] usb usb9: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 6.09 [ 1.201856] usb usb9: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.201859] usb usb9: Product: xHCI Host Controller [ 1.201861] usb usb9: Manufacturer: Linux 6.9.2-arch1-1.3 xhci-hcd [ 1.201863] usb usb9: SerialNumber: 0000:02:00.0 [ 1.202220] hub 9-0:1.0: USB hub found [ 1.202234] hub 9-0:1.0: 4 ports detected [ 1.267571] usb 1-3: new low-speed USB device number 2 using ohci-pci [ 1.454222] usb 8-1: new high-speed USB device number 2 using xhci_hcd [ 1.457506] tsc: Refined TSC clocksource calibration: 3322.063 MHz [ 1.457523] clocksource: tsc: mask: 0xffffffffffffffff max_cycles: 0x2fe2b689782, max_idle_ns: 440795272807 ns [ 1.457602] clocksource: Switched to clocksource tsc [ 1.457630] usb 1-3: New USB device found, idVendor=0c45, idProduct=7603, bcdDevice= 1.06 [ 1.457636] usb 1-3: New USB device strings: Mfr=0, Product=2, SerialNumber=0 [ 1.457639] usb 1-3: Product: USB Keyboard [ 1.481139] usbcore: registered new interface driver usbhid [ 1.481142] usbhid: USB HID core driver [ 1.486931] input: USB Keyboard as /devices/pci0000:00/0000:00:12.0/usb1/1-3/1-3:1.0/0003:0C45:7603.0001/input/input2 [ 1.541271] hid-generic 0003:0C45:7603.0001: input,hidraw0: USB HID v1.11 Keyboard [USB Keyboard] on usb-0000:00:12.0-3/input0 [ 1.541717] input: USB Keyboard Consumer Control as /devices/pci0000:00/0000:00:12.0/usb1/1-3/1-3:1.1/0003:0C45:7603.0002/input/input3 [ 1.595598] usb 8-1: New USB device found, idVendor=2109, idProduct=3431, bcdDevice= 4.20 [ 1.595602] usb 8-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0 [ 1.595604] usb 8-1: Product: USB2.0 Hub [ 1.596308] hub 8-1:1.0: USB hub found [ 1.596496] hub 8-1:1.0: 4 ports detected [ 1.597725] input: USB Keyboard System Control as /devices/pci0000:00/0000:00:12.0/usb1/1-3/1-3:1.1/0003:0C45:7603.0002/input/input4 [ 1.597805] input: USB Keyboard as /devices/pci0000:00/0000:00:12.0/usb1/1-3/1-3:1.1/0003:0C45:7603.0002/input/input6 [ 1.597946] hid-generic 0003:0C45:7603.0002: input,hiddev96,hidraw1: USB HID v1.11 Keyboard [USB Keyboard] on usb-0000:00:12.0-3/input1 [ 2.087564] usb 4-1: new full-speed USB device number 2 using ohci-pci [ 2.282353] usb 4-1: New USB device found, idVendor=04d9, idProduct=a088, bcdDevice= 1.00 [ 2.282365] usb 4-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0 [ 2.282370] usb 4-1: Product: USB Gaming Mouse [ 2.282375] usb 4-1: Manufacturer: RH [ 2.289761] input: RH USB Gaming Mouse as /devices/pci0000:00/0000:00:12.1/usb4/4-1/4-1:1.0/0003:04D9:A088.0003/input/input7 [ 2.344621] hid-generic 0003:04D9:A088.0003: input,hidraw2: USB HID v1.10 Keyboard [RH USB Gaming Mouse] on usb-0000:00:12.1-1/input0 [ 2.352021] input: RH USB Gaming Mouse as /devices/pci0000:00/0000:00:12.1/usb4/4-1/4-1:1.1/0003:04D9:A088.0004/input/input8 [ 2.352086] input: RH USB Gaming Mouse System Control as /devices/pci0000:00/0000:00:12.1/usb4/4-1/4-1:1.1/0003:04D9:A088.0004/input/input9 [ 2.407892] input: RH USB Gaming Mouse Consumer Control as /devices/pci0000:00/0000:00:12.1/usb4/4-1/4-1:1.1/0003:04D9:A088.0004/input/input10 [ 2.408041] hid-generic 0003:04D9:A088.0004: input,hiddev97,hidraw3: USB HID v1.10 Mouse [RH USB Gaming Mouse] on usb-0000:00:12.1-1/input1 [ 2.411712] hid-generic 0003:04D9:A088.0005: hiddev98,hidraw4: USB HID v1.10 Device [RH USB Gaming Mouse] on usb-0000:00:12.1-1/input2 [ 3.035241] EXT4-fs (sda2): mounted filesystem 963daeed-0888-4658-9f17-18bd343dfb2a r/w with ordered data mode. Quota mode: none. [ 3.204415] systemd[1]: systemd 255.7-1-arch running in system mode (+PAM +AUDIT -SELINUX -APPARMOR -IMA +SMACK +SECCOMP +GCRYPT +GNUTLS +OPENSSL +ACL +BLKID +CURL +ELFUTILS +FIDO2 +IDN2 -IDN +IPTC +KMOD +LIBCRYPTSETUP +LIBFDISK +PCRE2 +PWQUALITY +P11KIT +QRENCODE +TPM2 +BZIP2 +LZ4 +XZ +ZLIB +ZSTD +BPF_FRAMEWORK +XKBCOMMON +UTMP -SYSVINIT default-hierarchy=unified) [ 3.204423] systemd[1]: Detected architecture x86-64. [ 3.704252] systemd[1]: bpf-lsm: LSM BPF program attached [ 3.755371] systemd-fstab-generator[269]: Mount point is not a valid path, ignoring. [ 3.755953] systemd-fstab-generator[269]: Mount point is not a valid path, ignoring. [ 4.457554] random: crng init done [ 4.472946] zram: Added device: zram0 [ 4.637985] systemd[1]: Queued start job for default target Graphical Interface. [ 4.678959] systemd[1]: Created slice Slice /system/dirmngr. [ 4.679369] systemd[1]: Created slice Slice /system/getty. [ 4.679736] systemd[1]: Created slice Slice /system/gpg-agent. [ 4.680110] systemd[1]: Created slice Slice /system/gpg-agent-browser. [ 4.680482] systemd[1]: Created slice Slice /system/gpg-agent-extra. [ 4.680878] systemd[1]: Created slice Slice /system/gpg-agent-ssh. [ 4.681254] systemd[1]: Created slice Slice /system/keyboxd. [ 4.681618] systemd[1]: Created slice Slice /system/modprobe. [ 4.681937] systemd[1]: Created slice Slice /system/systemd-fsck. [ 4.682266] systemd[1]: Created slice Slice /system/systemd-zram-setup. [ 4.682496] systemd[1]: Created slice User and Session Slice. [ 4.682557] systemd[1]: Started Dispatch Password Requests to Console Directory Watch. [ 4.682603] systemd[1]: Started Forward Password Requests to Wall Directory Watch. [ 4.682749] systemd[1]: Set up automount Arbitrary Executable File Formats File System Automount Point. [ 4.682768] systemd[1]: Expecting device /dev/disk/by-uuid/03ce297b-4be8-4886-953d-2d2cc4bd0862... [ 4.682776] systemd[1]: Expecting device /dev/disk/by-uuid/6BB1-1CFA... [ 4.682783] systemd[1]: Expecting device /dev/zram0... [ 4.682795] systemd[1]: Reached target Local Encrypted Volumes. [ 4.682813] systemd[1]: Reached target Local Integrity Protected Volumes. [ 4.682837] systemd[1]: Reached target Path Units. [ 4.682851] systemd[1]: Reached target Remote File Systems. [ 4.682861] systemd[1]: Reached target Slice Units. [ 4.682890] systemd[1]: Reached target Local Verity Protected Volumes. [ 4.682963] systemd[1]: Listening on Device-mapper event daemon FIFOs. [ 4.683296] systemd[1]: Listening on LVM2 poll daemon socket. [ 4.684820] systemd[1]: Listening on Process Core Dump Socket. [ 4.684936] systemd[1]: Listening on Journal Socket (/dev/log). [ 4.685041] systemd[1]: Listening on Journal Socket. [ 4.685173] systemd[1]: Listening on Network Service Netlink Socket. [ 4.685190] systemd[1]: TPM2 PCR Extension (Varlink) was skipped because of an unmet condition check (ConditionSecurity=measured-uki). [ 4.685489] systemd[1]: Listening on udev Control Socket. [ 4.685574] systemd[1]: Listening on udev Kernel Socket. [ 4.687027] systemd[1]: Mounting Huge Pages File System... [ 4.687760] systemd[1]: Mounting POSIX Message Queue File System... [ 4.688524] systemd[1]: Mounting Kernel Debug File System... [ 4.689247] systemd[1]: Mounting Kernel Trace File System... [ 4.690393] systemd[1]: Starting Create List of Static Device Nodes... [ 4.691389] systemd[1]: Starting Monitoring of LVM2 mirrors, snapshots etc. using dmeventd or progress polling... [ 4.692560] systemd[1]: Starting Load Kernel Module configfs... [ 4.694984] systemd[1]: Starting Load Kernel Module dm_mod... [ 4.697704] systemd[1]: Starting Load Kernel Module drm... [ 4.698928] systemd[1]: Starting Load Kernel Module fuse... [ 4.699880] systemd[1]: Starting Load Kernel Module loop... [ 4.699948] systemd[1]: File System Check on Root Device was skipped because of an unmet condition check (ConditionPathIsReadWrite=!/). [ 4.702243] systemd[1]: Starting Journal Service... [ 4.705201] systemd[1]: Starting Load Kernel Modules... [ 4.706206] systemd[1]: Starting Generate network units from Kernel command line... [ 4.706241] systemd[1]: TPM2 PCR Machine ID Measurement was skipped because of an unmet condition check (ConditionSecurity=measured-uki). [ 4.707349] systemd[1]: Starting Remount Root and Kernel File Systems... [ 4.707431] systemd[1]: TPM2 SRK Setup (Early) was skipped because of an unmet condition check (ConditionSecurity=measured-uki). [ 4.709289] systemd[1]: Starting Coldplug All udev Devices... [ 4.711777] systemd[1]: Mounted Huge Pages File System. [ 4.711955] systemd[1]: Mounted POSIX Message Queue File System. [ 4.712065] systemd[1]: Mounted Kernel Debug File System. [ 4.712184] systemd[1]: Mounted Kernel Trace File System. [ 4.712458] systemd[1]: Finished Create List of Static Device Nodes. [ 4.712869] systemd[1]: modprobe@configfs.service: Deactivated successfully. [ 4.713131] systemd[1]: Finished Load Kernel Module configfs. [ 4.713552] systemd[1]: modprobe@drm.service: Deactivated successfully. [ 4.713739] systemd[1]: Finished Load Kernel Module drm. [ 4.714168] systemd[1]: modprobe@fuse.service: Deactivated successfully. [ 4.714388] systemd[1]: Finished Load Kernel Module fuse. [ 4.715895] systemd[1]: Mounting FUSE Control File System... [ 4.719435] systemd[1]: Mounting Kernel Configuration File System... [ 4.722528] systemd[1]: Starting Create Static Device Nodes in /dev gracefully... [ 4.722962] systemd[1]: Finished Generate network units from Kernel command line. [ 4.726581] loop: module loaded [ 4.726666] device-mapper: uevent: version 1.0.3 [ 4.726785] device-mapper: ioctl: 4.48.0-ioctl (2023-03-01) initialised: dm-devel@xxxxxxxxxxxxxxx [ 4.727625] systemd[1]: modprobe@dm_mod.service: Deactivated successfully. [ 4.727806] systemd[1]: Finished Load Kernel Module dm_mod. [ 4.728143] systemd[1]: modprobe@loop.service: Deactivated successfully. [ 4.728294] systemd[1]: Finished Load Kernel Module loop. [ 4.728436] systemd[1]: Mounted FUSE Control File System. [ 4.728536] systemd[1]: Mounted Kernel Configuration File System. [ 4.730091] systemd[1]: Repartition Root Disk was skipped because no trigger condition checks were met. [ 4.737696] EXT4-fs (sda2): re-mounted 963daeed-0888-4658-9f17-18bd343dfb2a r/w. Quota mode: none. [ 4.738458] systemd-journald[293]: Collecting audit messages is disabled. [ 4.738774] systemd[1]: Finished Remount Root and Kernel File Systems. [ 4.739317] sd 1:0:0:0: Attached scsi generic sg0 type 0 [ 4.739357] sd 2:0:0:0: Attached scsi generic sg1 type 0 [ 4.740284] systemd[1]: Rebuild Hardware Database was skipped because no trigger condition checks were met. [ 4.741389] systemd[1]: Starting Load/Save OS Random Seed... [ 4.741419] systemd[1]: TPM2 SRK Setup was skipped because of an unmet condition check (ConditionSecurity=measured-uki). [ 4.747471] Asymmetric key parser 'pkcs8' registered [ 4.748531] systemd[1]: Finished Load Kernel Modules. [ 4.749793] systemd[1]: Starting Apply Kernel Variables... [ 4.762719] systemd[1]: Finished Load/Save OS Random Seed. [ 4.766178] systemd[1]: Finished Apply Kernel Variables. [ 4.775775] systemd[1]: Finished Create Static Device Nodes in /dev gracefully. [ 4.776951] systemd[1]: Starting Create System Users... [ 4.799839] systemd[1]: Finished Monitoring of LVM2 mirrors, snapshots etc. using dmeventd or progress polling. [ 4.804706] systemd[1]: Started Journal Service. [ 4.816414] systemd-journald[293]: Received client request to flush runtime journal. [ 4.824979] systemd-journald[293]: /var/log/journal/ca3d73a04dc345538c9904a96756e41e/system.journal: Journal file uses a different sequence number ID, rotating. [ 4.824986] systemd-journald[293]: Rotating system journal. [ 4.984536] zram0: detected capacity change from 0 to 8388608 [ 5.028103] mousedev: PS/2 mouse device common for all mice [ 5.029341] parport_pc 00:04: reported by Plug and Play ACPI [ 5.029425] parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE] [ 5.049222] cryptd: max_cpu_qlen set to 1000 [ 5.050369] ACPI Warning: SystemIO range 0x0000000000000B00-0x0000000000000B08 conflicts with OpRegion 0x0000000000000B00-0x0000000000000B0F (\SOR1) (20230628/utaddress-204) [ 5.050382] ACPI: OSL: Resource conflict; ACPI support missing from driver? [ 5.051092] acpi_cpufreq: overriding BIOS provided _PSD data [ 5.051936] input: PC Speaker as /devices/platform/pcspkr/input/input12 [ 5.067613] sp5100_tco: SP5100/SB800 TCO WatchDog Timer Driver [ 5.067731] sp5100-tco sp5100-tco: Failed to reserve MMIO or alternate MMIO region [ 5.067735] sp5100-tco sp5100-tco: probe with driver sp5100-tco failed with error -16 [ 5.080852] AVX version of gcm_enc/dec engaged. [ 5.083989] AES CTR mode by8 optimization enabled [ 5.090062] r8169 0000:03:00.0: can't disable ASPM; OS doesn't have ASPM control [ 5.105231] r8169 0000:03:00.0 eth0: RTL8168g/8111g, e0:d5:5e:3b:15:1f, XID 4c0, IRQ 28 [ 5.105238] r8169 0000:03:00.0 eth0: jumbo features [frames: 9194 bytes, tx checksumming: ko] [ 5.109703] r8169 0000:03:00.0 enp3s0: renamed from eth0 [ 5.134683] ppdev: user-space parallel port driver [ 5.162871] snd_hda_intel 0000:01:00.1: Disabling MSI [ 5.162884] snd_hda_intel 0000:01:00.1: Handle vga_switcheroo audio client [ 5.171548] Adding 4194300k swap on /dev/zram0. Priority:100 extents:1 across:4194300k SSDsc [ 5.214513] input: HDA NVidia HDMI/DP,pcm=3 as /devices/pci0000:00/0000:00:02.0/0000:01:00.1/sound/card1/input13 [ 5.214589] input: HDA NVidia HDMI/DP,pcm=7 as /devices/pci0000:00/0000:00:02.0/0000:01:00.1/sound/card1/input14 [ 5.214658] input: HDA NVidia HDMI/DP,pcm=8 as /devices/pci0000:00/0000:00:02.0/0000:01:00.1/sound/card1/input15 [ 5.214726] input: HDA NVidia HDMI/DP,pcm=9 as /devices/pci0000:00/0000:00:02.0/0000:01:00.1/sound/card1/input16 [ 5.308685] snd_hda_codec_realtek hdaudioC0D0: autoconfig for ALC892: line_outs=1 (0x14/0x0/0x0/0x0/0x0) type:line [ 5.308693] snd_hda_codec_realtek hdaudioC0D0: speaker_outs=0 (0x0/0x0/0x0/0x0/0x0) [ 5.308696] snd_hda_codec_realtek hdaudioC0D0: hp_outs=1 (0x1b/0x0/0x0/0x0/0x0) [ 5.308698] snd_hda_codec_realtek hdaudioC0D0: mono: mono_out=0x0 [ 5.308700] snd_hda_codec_realtek hdaudioC0D0: dig-out=0x11/0x0 [ 5.308702] snd_hda_codec_realtek hdaudioC0D0: inputs: [ 5.308704] snd_hda_codec_realtek hdaudioC0D0: Front Mic=0x19 [ 5.308706] snd_hda_codec_realtek hdaudioC0D0: Rear Mic=0x18 [ 5.308708] snd_hda_codec_realtek hdaudioC0D0: Line=0x1a [ 5.326722] input: HDA ATI SB Front Mic as /devices/pci0000:00/0000:00:14.2/sound/card0/input17 [ 5.326807] input: HDA ATI SB Rear Mic as /devices/pci0000:00/0000:00:14.2/sound/card0/input18 [ 5.326871] input: HDA ATI SB Line as /devices/pci0000:00/0000:00:14.2/sound/card0/input19 [ 5.329070] input: HDA ATI SB Line Out as /devices/pci0000:00/0000:00:14.2/sound/card0/input20 [ 5.329531] input: HDA ATI SB Front Headphone as /devices/pci0000:00/0000:00:14.2/sound/card0/input21 [ 5.340116] kvm_amd: TSC scaling supported [ 5.340120] kvm_amd: Nested Virtualization enabled [ 5.340121] kvm_amd: Nested Paging enabled [ 5.340128] kvm_amd: LBR virtualization supported [ 5.894238] EXT4-fs (sdb1): mounted filesystem 03ce297b-4be8-4886-953d-2d2cc4bd0862 r/w with ordered data mode. Quota mode: none. [ 6.784621] NET: Registered PF_ALG protocol family [ 6.847510] Generic FE-GE Realtek PHY r8169-0-300:00: attached PHY driver (mii_bus:phy_addr=r8169-0-300:00, irq=MAC) [ 7.037662] r8169 0000:03:00.0 enp3s0: Link is Down [ 12.862299] systemd-journald[293]: /var/log/journal/ca3d73a04dc345538c9904a96756e41e/user-1000.journal: Journal file uses a different sequence number ID, rotating.
Attachment:
signature.asc
Description: PGP signature
