Hi Sergey,
On 24/08/23 04:05, Sergey Shtylyov wrote:
Hello!
I prefer CCing my OMP account when you send the PATA patches,
as is returned by scripts/get_maintainer.pl...
Sorry, I was left with the impression OMP was rejecting list messages
from linux-ide ...
On 8/23/23 1:13 AM, Michael Schmitz wrote:
With commit 44b1fbc0f5f3 ("m68k/q40: Replace q40ide driver
with pata_falcon and falconide"), the Q40 IDE driver was
replaced by pata_falcon.c.
Both IO and memory resources were defined for the Q40 IDE
platform device, but definition of the IDE register addresses
was modeled after the Falcon case, both in use of the memory
resources and in including register shift and byte vs. word
offset in the address.
This was correct for the Falcon case, which does not apply
any address translation to the register addresses. In the
Q40 case, all of device base address, byte access offset
and register shift is included in the platform specific
ISA access translation (in asm/mm_io.h).
As a consequence, such address translation gets applied
twice, and register addresses are mangled.
Use the device base address from the platform IO resource
for Q40 (the IO address translation will then add the correct
ISA window base address and byte access offset), with register
shift 1. Use MMIO base address and register shift 2 as before
for Falcon.
Encode PIO_OFFSET into IO port addresses for all registers
for Q40 except the data transfer register. Encode the MMIO
offset there (pata_falcon_data_xfer() directly uses raw IO
with no address translation).
Reported-by: William R Sowerbutts <will@xxxxxxxxxxxxxx>
Closes: https://lore.kernel.org/r/CAMuHMdUU62jjunJh9cqSqHT87B0H0A4udOOPs=WN7WZKpcagVA@xxxxxxxxxxxxxx
Link: https://lore.kernel.org/r/CAMuHMdUU62jjunJh9cqSqHT87B0H0A4udOOPs=WN7WZKpcagVA@xxxxxxxxxxxxxx
Fixes: 44b1fbc0f5f3 ("m68k/q40: Replace q40ide driver with pata_falcon and falconide")
Cc: stable@xxxxxxxxxxxxxxx
Cc: Finn Thain <fthain@xxxxxxxxxxxxxx>
Cc: Geert Uytterhoeven <geert@xxxxxxxxxxxxxx>
Tested-by: William R Sowerbutts <will@xxxxxxxxxxxxxx>
Signed-off-by: Michael Schmitz <schmitzmic@xxxxxxxxx>
Reviewed-by: Sergey Shtylyov <s.shtylyov@xxxxxx>
[...]
diff --git a/drivers/ata/pata_falcon.c b/drivers/ata/pata_falcon.c
index 996516e64f13..3841ea200bcb 100644
--- a/drivers/ata/pata_falcon.c
+++ b/drivers/ata/pata_falcon.c
[...]
@@ -165,26 +165,34 @@ static int __init pata_falcon_init_one(struct platform_device *pdev)
ap->pio_mask = ATA_PIO4;
ap->flags |= ATA_FLAG_SLAVE_POSS | ATA_FLAG_NO_IORDY;
- base = (void __iomem *)base_mem_res->start;
/* N.B. this assumes data_addr will be used for word-sized I/O only */
- ap->ioaddr.data_addr = base + 0 + 0 * 4;
- ap->ioaddr.error_addr = base + 1 + 1 * 4;
- ap->ioaddr.feature_addr = base + 1 + 1 * 4;
- ap->ioaddr.nsect_addr = base + 1 + 2 * 4;
- ap->ioaddr.lbal_addr = base + 1 + 3 * 4;
- ap->ioaddr.lbam_addr = base + 1 + 4 * 4;
- ap->ioaddr.lbah_addr = base + 1 + 5 * 4;
- ap->ioaddr.device_addr = base + 1 + 6 * 4;
- ap->ioaddr.status_addr = base + 1 + 7 * 4;
- ap->ioaddr.command_addr = base + 1 + 7 * 4;
-
- base = (void __iomem *)ctl_mem_res->start;
- ap->ioaddr.altstatus_addr = base + 1;
- ap->ioaddr.ctl_addr = base + 1;
-
- ata_port_desc(ap, "cmd 0x%lx ctl 0x%lx",
- (unsigned long)base_mem_res->start,
- (unsigned long)ctl_mem_res->start);
+ ap->ioaddr.data_addr = (void __iomem *)base_mem_res->start;
+
+ if (base_res) { /* only Q40 has IO resources */
+ io_offset = 0x10000;
+ reg_shift = 0;
+ base = (void __iomem *)base_res->start;
+ ctl_base = (void __iomem *)ctl_res->start;
+ } else {
+ base = (void __iomem *)base_mem_res->start;
+ ctl_base = (void __iomem *)ctl_mem_res->start;
+ }
+
+ ap->ioaddr.error_addr = base + io_offset + (1 << reg_shift);
+ ap->ioaddr.feature_addr = base + io_offset + (1 << reg_shift);
+ ap->ioaddr.nsect_addr = base + io_offset + (2 << reg_shift);
+ ap->ioaddr.lbal_addr = base + io_offset + (3 << reg_shift);
+ ap->ioaddr.lbam_addr = base + io_offset + (4 << reg_shift);
+ ap->ioaddr.lbah_addr = base + io_offset + (5 << reg_shift);
+ ap->ioaddr.device_addr = base + io_offset + (6 << reg_shift);
+ ap->ioaddr.status_addr = base + io_offset + (7 << reg_shift);
+ ap->ioaddr.command_addr = base + io_offset + (7 << reg_shift);
+
+ ap->ioaddr.altstatus_addr = ctl_base + io_offset;
+ ap->ioaddr.ctl_addr = ctl_base + io_offset;
+
+ ata_port_desc(ap, "cmd %px ctl %px data %pa",
+ base, ctl_base, &ap->ioaddr.data_addr);
Like Geert said, use "%px" and ap->ioaddr.data_addr here...
Will do.
Cheers,
Michael
[...]
MBR, Sergey
