There is a bug introduced in c312ef176399 "libata/ahci: Drop PCS quirk for Denverton and beyond": the quirk is not applied on wake from suspend as it originally was. Because of that my laptop (ICH8M controller) doesnt see KINGSTON SV300S37A60G SSD disk connected into a SATA connector on wake since kernel 5.3.4 or better to say 5.3.8 because there was another error in c312ef176399 until a fix arrived in 09d6ac8dc51a "libata/ahci: Fix PCS quirk application". Btw 4.19.y lts branch is affected as well. The problem somewhy doesnt trigger on another disk though (WD5000LPCX HDD). I discovered it upgrading the laptop with the SSD in place of a HDD with some 5.4 kernel. Here is my hardware: - Acer 5920G with ICH8M SATA controller - sda: some SATA HDD connnected into the DVD drive IDE port with a SATA-IDE caddy. It is a boot disk to test kernels - sdb: KINGSTON SV300S37A60G SSD connected into the only SATA port Booting into vanilla 5.3.8 and beyond (built from upstream sources with configs extracted from https://kernel.ubuntu.com/~kernel-ppa/mainline/) I see both disks in lsblk. After wake from suspend the SSD is gone from lsblk output. Here is sample "dmesg --notime | grep -E '^(sd |ata)'" output on wake: sd 0:0:0:0: [sda] Starting disk sd 2:0:0:0: [sdb] Starting disk ata4: SATA link down (SStatus 4 SControl 300) ata3: SATA link down (SStatus 4 SControl 300) ata1.00: ACPI cmd ef/03:0c:00:00:00:a0 (SET FEATURES) filtered out ata1.00: ACPI cmd ef/03:42:00:00:00:a0 (SET FEATURES) filtered out ata1: FORCE: cable set to 80c ata5: SATA link down (SStatus 0 SControl 300) ata3: SATA link down (SStatus 4 SControl 300) ata3: SATA link down (SStatus 4 SControl 300) ata3.00: disabled sd 2:0:0:0: rejecting I/O to offline device ata3.00: detaching (SCSI 2:0:0:0) sd 2:0:0:0: [sdb] Start/Stop Unit failed: Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK sd 2:0:0:0: [sdb] Synchronizing SCSI cache sd 2:0:0:0: [sdb] Synchronize Cache(10) failed: Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK sd 2:0:0:0: [sdb] Stopping disk sd 2:0:0:0: [sdb] Start/Stop Unit failed: Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK The patch is tested on 6.0.10, it solves the problem for my hardware. diff --git a/drivers/ata/ahci.c b/drivers/ata/ahci.c index c1eca72b4575..28d8c56cb4dd 100644 --- a/drivers/ata/ahci.c +++ b/drivers/ata/ahci.c @@ -84,6 +84,7 @@ enum board_ids { static int ahci_init_one(struct pci_dev *pdev, const struct pci_device_id *ent); static void ahci_remove_one(struct pci_dev *dev); static void ahci_shutdown_one(struct pci_dev *dev); +static void ahci_intel_pcs_quirk(struct pci_dev *pdev, struct ahci_host_priv *hpriv); static int ahci_vt8251_hardreset(struct ata_link *link, unsigned int *class, unsigned long deadline); static int ahci_avn_hardreset(struct ata_link *link, unsigned int *class, @@ -677,6 +678,25 @@ static void ahci_pci_save_initial_config(struct pci_dev *pdev, ahci_save_initial_config(&pdev->dev, hpriv); } +static int ahci_pci_reset_controller(struct ata_host *host) +{ + struct pci_dev *pdev = to_pci_dev(host->dev); + struct ahci_host_priv *hpriv = host->private_data; + int rc; + + rc = ahci_reset_controller(host); + if (rc) + return rc; + + /* + * If platform firmware failed to enable ports, try to enable + * them here. + */ + ahci_intel_pcs_quirk(pdev, hpriv); + + return 0; +} + static void ahci_pci_init_controller(struct ata_host *host) { struct ahci_host_priv *hpriv = host->private_data; @@ -871,7 +891,7 @@ static int ahci_pci_device_runtime_resume(struct device *dev) struct ata_host *host = pci_get_drvdata(pdev); int rc; - rc = ahci_reset_controller(host); + rc = ahci_pci_reset_controller(host); if (rc) return rc; ahci_pci_init_controller(host); @@ -907,7 +927,7 @@ static int ahci_pci_device_resume(struct device *dev) ahci_mcp89_apple_enable(pdev); if (pdev->dev.power.power_state.event == PM_EVENT_SUSPEND) { - rc = ahci_reset_controller(host); + rc = ahci_pci_reset_controller(host); if (rc) return rc; @@ -1788,12 +1808,6 @@ static int ahci_init_one(struct pci_dev *pdev, const struct pci_device_id *ent) /* save initial config */ ahci_pci_save_initial_config(pdev, hpriv); - /* - * If platform firmware failed to enable ports, try to enable - * them here. - */ - ahci_intel_pcs_quirk(pdev, hpriv); - /* prepare host */ if (hpriv->cap & HOST_CAP_NCQ) { pi.flags |= ATA_FLAG_NCQ; @@ -1903,7 +1917,7 @@ static int ahci_init_one(struct pci_dev *pdev, const struct pci_device_id *ent) if (rc) return rc; - rc = ahci_reset_controller(host); + rc = ahci_pci_reset_controller(host); if (rc) return rc;
