On Thu, Jun 16, 2022 at 09:29:50AM +0900, Damien Le Moal wrote:
> On 2022/06/16 6:11, Serge Semin wrote:
> > On Tue, Jun 14, 2022 at 05:42:35PM +0900, Damien Le Moal wrote:
> >> On 6/10/22 17:17, Serge Semin wrote:
> >>> There are systems with no BIOS or comprehensive embedded firmware which
> >>> could be able to properly initialize the SATA AHCI controller
> >>> platform-specific capabilities. In that case a good alternative to having
> >>> a clever bootloader is to create a device tree node with the properties
> >>> well describing all the AHCI-related platform specifics. All the settings
> >>> which are normally detected and marked as available in the HBA and its
> >>> ports capabilities fields [1] could be defined in the platform DTB by
> >>> means of a set of the dedicated properties. Such approach perfectly fits
> >>> to the DTB-philosophy - to provide hardware/platform description.
> >>>
> >>> So here we suggest to extend the SATA AHCI device tree bindings with two
> >>> additional DT-properties:
> >>> 1) "hba-cap" - HBA platform generic capabilities like:
> >>> - SSS - Staggered Spin-up support.
> >>> - SMPS - Mechanical Presence Switch support.
> >>> 2) "hba-port-cap" - HBA platform port capabilities like:
> >>> - HPCP - Hot Plug Capable Port.
> >>> - MPSP - Mechanical Presence Switch Attached to Port.
> >>> - CPD - Cold Presence Detection.
> >>> - ESP - External SATA Port.
> >>> - FBSCP - FIS-based Switching Capable Port.
> >>> All of these capabilities require to have a corresponding hardware
> >>> configuration. Thus it's ok to have them defined in DTB.
> >>>
> >>> Even though the driver currently takes into account the state of the ESP
> >>> and FBSCP flags state only, there is nothing wrong with having all of them
> >>> supported by the generic AHCI library in order to have a complete OF-based
> >>> platform-capabilities initialization procedure. These properties will be
> >>> parsed in the ahci_platform_get_resources() method and their values will
> >>> be stored in the saved_* fields of the ahci_host_priv structure, which in
> >>> its turn then will be used to restore the H.CAP, H.PI and P#.CMD
> >>> capability fields on device init and after HBA reset.
> >>>
> >>> Please note this modification concerns the HW-init HBA and its ports flags
> >>> only, which are by specification [1] are supposed to be initialized by the
> >>> BIOS/platform firmware/expansion ROM and which are normally declared in
> >>> the one-time-writable-after-reset register fields. Even though these flags
> >>> aren't supposed to be cleared after HBA reset some AHCI instances may
> >>> violate that rule so we still need to perform the fields resetting after
> >>> each reset. Luckily the corresponding functionality has already been
> >>> partly implemented in the framework of the ahci_save_initial_config() and
> >>> ahci_restore_initial_config() methods.
> >>>
> >>> [1] Serial ATA AHCI 1.3.1 Specification, p. 103
> >>>
> >>> Signed-off-by: Serge Semin <Sergey.Semin@xxxxxxxxxxxxxxxxxxxx>
> >>>
> >>> ---
> >>>
> >>> Changelog v4:
> >>> - Convert the boolean properties to the bitfield DT-properties. (@Rob)
> >>> ---
> >>> drivers/ata/ahci.h | 1 +
> >>> drivers/ata/libahci.c | 51 ++++++++++++++++++++++++++++------
> >>> drivers/ata/libahci_platform.c | 41 +++++++++++++++++++++++++--
> >>> 3 files changed, 82 insertions(+), 11 deletions(-)
> >>>
> >>> diff --git a/drivers/ata/ahci.h b/drivers/ata/ahci.h
> >>> index 8b9826533ae5..0de221055961 100644
> >>> --- a/drivers/ata/ahci.h
> >>> +++ b/drivers/ata/ahci.h
> >>> @@ -337,6 +337,7 @@ struct ahci_host_priv {
> >>> u32 saved_cap; /* saved initial cap */
> >>> u32 saved_cap2; /* saved initial cap2 */
> >>> u32 saved_port_map; /* saved initial port_map */
> >>> + u32 saved_port_cap[AHCI_MAX_PORTS]; /* saved port_cap */
> >>> u32 em_loc; /* enclosure management location */
> >>> u32 em_buf_sz; /* EM buffer size in byte */
> >>> u32 em_msg_type; /* EM message type */
> >>> diff --git a/drivers/ata/libahci.c b/drivers/ata/libahci.c
> >>> index 1ffaa5f5f21a..954386a2b500 100644
> >>> --- a/drivers/ata/libahci.c
> >>> +++ b/drivers/ata/libahci.c
> >>> @@ -16,6 +16,7 @@
> >>> * http://www.intel.com/technology/serialata/pdf/rev1_1.pdf
> >>> */
> >>>
> >>> +#include <linux/bitops.h>
> >>> #include <linux/kernel.h>
> >>> #include <linux/gfp.h>
> >>> #include <linux/module.h>
> >>> @@ -443,16 +444,28 @@ static ssize_t ahci_show_em_supported(struct device *dev,
> >>> void ahci_save_initial_config(struct device *dev, struct ahci_host_priv *hpriv)
> >>> {
> >>> void __iomem *mmio = hpriv->mmio;
> >>> - u32 cap, cap2, vers, port_map;
> >>> + void __iomem *port_mmio;
> >>> + unsigned long port_map;
> >>> + u32 cap, cap2, vers;
> >>> int i;
> >>>
> >>> /* make sure AHCI mode is enabled before accessing CAP */
> >>> ahci_enable_ahci(mmio);
> >>>
> >>> - /* Values prefixed with saved_ are written back to host after
> >>> - * reset. Values without are used for driver operation.
> >>> + /*
> >>> + * Values prefixed with saved_ are written back to the HBA and ports
> >>> + * registers after reset. Values without are used for driver operation.
> >>> + */
> >>> +
> >>> + /*
> >>> + * Override HW-init HBA capability fields with the platform-specific
> >>> + * values. The rest of the HBA capabilities are defined as Read-only
> >>> + * and can't be modified in CSR anyway.
> >>> */
> >>> - hpriv->saved_cap = cap = readl(mmio + HOST_CAP);
> >>> + cap = readl(mmio + HOST_CAP);
> >>> + if (hpriv->saved_cap)
> >>> + cap = (cap & ~(HOST_CAP_SSS | HOST_CAP_MPS)) | hpriv->saved_cap;
> >>> + hpriv->saved_cap = cap;
> >>>
> >>> /* CAP2 register is only defined for AHCI 1.2 and later */
> >>> vers = readl(mmio + HOST_VERSION);
> >>> @@ -519,7 +532,7 @@ void ahci_save_initial_config(struct device *dev, struct ahci_host_priv *hpriv)
> >>> /* Override the HBA ports mapping if the platform needs it */
> >>> port_map = readl(mmio + HOST_PORTS_IMPL);
> >>> if (hpriv->saved_port_map && port_map != hpriv->saved_port_map) {
> >>> - dev_info(dev, "forcing port_map 0x%x -> 0x%x\n",
> >>> + dev_info(dev, "forcing port_map 0x%lx -> 0x%x\n",
> >>
> >
> >> This change is not necessary.
> >
> > It is. The port_map type has been changed.
>
> Ignore. When I read the patches the other day, the mailer font had that "l" look
> like a "1" :) My mistake.
Ok.)
-Sergey
>
> >
> >>
> >>> port_map, hpriv->saved_port_map);
> >>> port_map = hpriv->saved_port_map;
> >>> } else {
> >>> @@ -527,7 +540,7 @@ void ahci_save_initial_config(struct device *dev, struct ahci_host_priv *hpriv)
> >>> }
> >>>
> >>> if (hpriv->mask_port_map) {
> >>> - dev_warn(dev, "masking port_map 0x%x -> 0x%x\n",
> >>> + dev_warn(dev, "masking port_map 0x%lx -> 0x%lx\n",
> >>
> >> Same.
> >
> > ditto
> >
> >>
> >>> port_map,
> >>> port_map & hpriv->mask_port_map);
> >>> port_map &= hpriv->mask_port_map;
> >>> @@ -546,7 +559,7 @@ void ahci_save_initial_config(struct device *dev, struct ahci_host_priv *hpriv)
> >>> */
> >>> if (map_ports > ahci_nr_ports(cap)) {
> >>> dev_warn(dev,
> >>> - "implemented port map (0x%x) contains more ports than nr_ports (%u), using nr_ports\n",
> >>> + "implemented port map (0x%lx) contains more ports than nr_ports (%u), using nr_ports\n",
> >>
> >> Same.
> >
> > ditto.
> >
> >>
> >>> port_map, ahci_nr_ports(cap));
> >>> port_map = 0;
> >>> }
> >>> @@ -555,12 +568,26 @@ void ahci_save_initial_config(struct device *dev, struct ahci_host_priv *hpriv)
> >>> /* fabricate port_map from cap.nr_ports for < AHCI 1.3 */
> >>> if (!port_map && vers < 0x10300) {
> >>> port_map = (1 << ahci_nr_ports(cap)) - 1;
> >>> - dev_warn(dev, "forcing PORTS_IMPL to 0x%x\n", port_map);
> >>> + dev_warn(dev, "forcing PORTS_IMPL to 0x%lx\n", port_map);
> >>
> >> And again not needed.
> >
> > and ditto.
> >
> >>
> >>>
> >>> /* write the fixed up value to the PI register */
> >>> hpriv->saved_port_map = port_map;
> >>> }
> >>>
> >>> + /*
> >>> + * Preserve the ports capabilities defined by the platform. Note there
> >>> + * is no need in storing the rest of the P#.CMD fields since they are
> >>> + * volatile.
> >>> + */
> >>> + for_each_set_bit(i, &port_map, AHCI_MAX_PORTS) {
> >>> + if (hpriv->saved_port_cap[i])
> >>> + continue;
> >>> +
> >>> + port_mmio = __ahci_port_base(hpriv, i);
> >>> + hpriv->saved_port_cap[i] =
> >>> + readl(port_mmio + PORT_CMD) & PORT_CMD_CAP;
> >>> + }
> >>> +
> >>> /* record values to use during operation */
> >>> hpriv->cap = cap;
> >>> hpriv->cap2 = cap2;
> >>> @@ -590,13 +617,21 @@ EXPORT_SYMBOL_GPL(ahci_save_initial_config);
> >>> static void ahci_restore_initial_config(struct ata_host *host)
> >>> {
> >>> struct ahci_host_priv *hpriv = host->private_data;
> >>> + unsigned long port_map = hpriv->port_map;
> >>> void __iomem *mmio = hpriv->mmio;
> >>> + void __iomem *port_mmio;
> >>> + int i;
> >>>
> >>> writel(hpriv->saved_cap, mmio + HOST_CAP);
> >>> if (hpriv->saved_cap2)
> >>> writel(hpriv->saved_cap2, mmio + HOST_CAP2);
> >>> writel(hpriv->saved_port_map, mmio + HOST_PORTS_IMPL);
> >>> (void) readl(mmio + HOST_PORTS_IMPL); /* flush */
> >>> +
> >>> + for_each_set_bit(i, &port_map, AHCI_MAX_PORTS) {
> >>> + port_mmio = __ahci_port_base(hpriv, i);
> >>> + writel(hpriv->saved_port_cap[i], port_mmio + PORT_CMD);
> >>> + }
> >>> }
> >>>
> >>> static unsigned ahci_scr_offset(struct ata_port *ap, unsigned int sc_reg)
> >>> diff --git a/drivers/ata/libahci_platform.c b/drivers/ata/libahci_platform.c
> >>> index efe640603f3f..8b542a8bc487 100644
> >>> --- a/drivers/ata/libahci_platform.c
> >>> +++ b/drivers/ata/libahci_platform.c
> >>> @@ -23,6 +23,7 @@
> >>> #include <linux/pm_runtime.h>
> >>> #include <linux/of_platform.h>
> >>> #include <linux/reset.h>
> >>> +
> >>
> >> white line change.
> >
> > Ok. I'll drop it.
> >
> > -Sergey
> >
> >>
> >>> #include "ahci.h"
> >>>
> >>> static void ahci_host_stop(struct ata_host *host);
> >>> @@ -383,6 +384,34 @@ static int ahci_platform_get_regulator(struct ahci_host_priv *hpriv, u32 port,
> >>> return rc;
> >>> }
> >>>
> >>> +static int ahci_platform_get_firmware(struct ahci_host_priv *hpriv,
> >>> + struct device *dev)
> >>> +{
> >>> + struct device_node *child;
> >>> + u32 port;
> >>> +
> >>> + if (!of_property_read_u32(dev->of_node, "hba-cap", &hpriv->saved_cap))
> >>> + hpriv->saved_cap &= (HOST_CAP_SSS | HOST_CAP_MPS);
> >>> +
> >>> + of_property_read_u32(dev->of_node,
> >>> + "ports-implemented", &hpriv->saved_port_map);
> >>> +
> >>> + for_each_child_of_node(dev->of_node, child) {
> >>> + if (!of_device_is_available(child))
> >>> + continue;
> >>> +
> >>> + if (of_property_read_u32(child, "reg", &port)) {
> >>> + of_node_put(child);
> >>> + return -EINVAL;
> >>> + }
> >>> +
> >>> + if (!of_property_read_u32(child, "hba-port-cap", &hpriv->saved_port_cap[port]))
> >>> + hpriv->saved_port_cap[port] &= PORT_CMD_CAP;
> >>> + }
> >>> +
> >>> + return 0;
> >>> +}
> >>> +
> >>> /**
> >>> * ahci_platform_get_resources - Get platform resources
> >>> * @pdev: platform device to get resources for
> >>> @@ -523,9 +552,6 @@ struct ahci_host_priv *ahci_platform_get_resources(struct platform_device *pdev,
> >>> goto err_out;
> >>> }
> >>>
> >>> - of_property_read_u32(dev->of_node,
> >>> - "ports-implemented", &hpriv->saved_port_map);
> >>> -
> >>> if (child_nodes) {
> >>> for_each_child_of_node(dev->of_node, child) {
> >>> u32 port;
> >>> @@ -590,6 +616,15 @@ struct ahci_host_priv *ahci_platform_get_resources(struct platform_device *pdev,
> >>> if (rc == -EPROBE_DEFER)
> >>> goto err_out;
> >>> }
> >>> +
> >>> + /*
> >>> + * Retrieve firmware-specific flags which then will be used to set
> >>> + * the HW-init fields of HBA and its ports
> >>> + */
> >>> + rc = ahci_platform_get_firmware(hpriv, dev);
> >>> + if (rc)
> >>> + goto err_out;
> >>> +
> >>> pm_runtime_enable(dev);
> >>> pm_runtime_get_sync(dev);
> >>> hpriv->got_runtime_pm = true;
> >>
> >>
> >> --
> >> Damien Le Moal
> >> Western Digital Research
>
>
> --
> Damien Le Moal
> Western Digital Research
