On Tue, Jun 14, 2022 at 05:32:41PM +0900, Damien Le Moal wrote:
> On 6/10/22 17:17, Serge Semin wrote:
> > Currently not all of the Port-specific capabilities listed in the
>
> s/listed/are listed
>
> > PORT_CMD-enumeration. Let's extend that set with the Cold Presence
> > Detection and Mechanical Presence Switch attached to the Port flags [1] so
> > to closeup the set of the platform-specific port-capabilities flags. Note
> > these flags are supposed to be set by the platform firmware if there is
> > one. Alternatively as we are about to do they can be set by means of the
> > OF properties.
> >
> > While at it replace PORT_IRQ_DEV_ILCK with PORT_IRQ_DMPS and fix the
> > comment there. In accordance with [2] that IRQ flag is supposed to
> > indicate the state of the signal coming from the Mechanical Presence
> > Switch.
> >
> > [1] Serial ATA AHCI 1.3.1 Specification, p.27
> > [2] Serial ATA AHCI 1.3.1 Specification, p.24, p.88
> >
> > Signed-off-by: Serge Semin <Sergey.Semin@xxxxxxxxxxxxxxxxxxxx>
> > Reviewed-by: Hannes Reinecke <hare@xxxxxxx>
> >
> > ---
> >
> > Changelog v4:
> > - Fix the DMPS macros name in the patch log. (@Sergei Shtylyov)
> > ---
> > drivers/ata/ahci.h | 7 ++++++-
> > 1 file changed, 6 insertions(+), 1 deletion(-)
> >
> > diff --git a/drivers/ata/ahci.h b/drivers/ata/ahci.h
> > index 7d834deefeb9..f501531bd1b3 100644
> > --- a/drivers/ata/ahci.h
> > +++ b/drivers/ata/ahci.h
> > @@ -138,7 +138,7 @@ enum {
> > PORT_IRQ_BAD_PMP = (1 << 23), /* incorrect port multiplier */
> >
> > PORT_IRQ_PHYRDY = (1 << 22), /* PhyRdy changed */
> > - PORT_IRQ_DEV_ILCK = (1 << 7), /* device interlock */
> > + PORT_IRQ_DMPS = (1 << 7), /* mechanical presence status */
> > PORT_IRQ_CONNECT = (1 << 6), /* port connect change status */
> > PORT_IRQ_SG_DONE = (1 << 5), /* descriptor processed */
> > PORT_IRQ_UNK_FIS = (1 << 4), /* unknown FIS rx'd */
> > @@ -166,6 +166,8 @@ enum {
> > PORT_CMD_ATAPI = (1 << 24), /* Device is ATAPI */
> > PORT_CMD_FBSCP = (1 << 22), /* FBS Capable Port */
> > PORT_CMD_ESP = (1 << 21), /* External Sata Port */
> > + PORT_CMD_CPD = (1 << 20), /* Cold Presence Detection */
> > + PORT_CMD_MPSP = (1 << 19), /* Mechanical Presence Switch */
> > PORT_CMD_HPCP = (1 << 18), /* HotPlug Capable Port */
> > PORT_CMD_PMP = (1 << 17), /* PMP attached */
> > PORT_CMD_LIST_ON = (1 << 15), /* cmd list DMA engine running */
> > @@ -181,6 +183,9 @@ enum {
> > PORT_CMD_ICC_PARTIAL = (0x2 << 28), /* Put i/f in partial state */
> > PORT_CMD_ICC_SLUMBER = (0x6 << 28), /* Put i/f in slumber state */
> >
> > + PORT_CMD_CAP = PORT_CMD_HPCP | PORT_CMD_MPSP |
> > + PORT_CMD_CPD | PORT_CMD_ESP | PORT_CMD_FBSCP,
>
> What is this one for ? A comment above it would be nice.
Isn't it obviously inferrable from the definition and the item name?
-Sergey
>
> > +
> > /* PORT_FBS bits */
> > PORT_FBS_DWE_OFFSET = 16, /* FBS device with error offset */
> > PORT_FBS_ADO_OFFSET = 12, /* FBS active dev optimization offset */
>
>
> --
> Damien Le Moal
> Western Digital Research
