Synopsys AHCI SATA controller is mainly compatible with the generic AHCI SATA controller except a few peculiarities and the platform environment requirements. In particular it can have one or two reference clocks to feed up its AXI/AHB interface and SATA PHYs domain and at least one reset control for the application clock domain. In addition to that the DMA interface of each port can be tuned up to work with the predefined maximum data chunk size. Note unlike generic AHCI controller DWC AHCI can't have more than 8 ports. All of that is reflected in the new DWC AHCI SATA device DT binding. Note the DWC AHCI SATA controller DT-schema has been created in a way so to be reused for the vendor-specific DT-schemas. One of which we are about to introduce. Signed-off-by: Serge Semin <Sergey.Semin@xxxxxxxxxxxxxxxxxxxx> --- .../bindings/ata/snps,dwc-ahci.yaml | 121 ++++++++++++++++++ 1 file changed, 121 insertions(+) create mode 100644 Documentation/devicetree/bindings/ata/snps,dwc-ahci.yaml diff --git a/Documentation/devicetree/bindings/ata/snps,dwc-ahci.yaml b/Documentation/devicetree/bindings/ata/snps,dwc-ahci.yaml new file mode 100644 index 000000000000..b443154b63aa --- /dev/null +++ b/Documentation/devicetree/bindings/ata/snps,dwc-ahci.yaml @@ -0,0 +1,121 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/ata/snps,dwc-ahci.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Synopsys DWC AHCI SATA controller + +maintainers: + - Serge Semin <fancer.lancer@xxxxxxxxx> + +description: | + This document defines device tree bindings for the Synopsys DWC + implementation of the AHCI SATA controller. + +allOf: + - $ref: ahci-common.yaml# + +properties: + compatible: + oneOf: + - description: Synopsys AHCI SATA-compatible devices + contains: + const: snps,dwc-ahci + - description: SPEAr1340 AHCI SATA device + const: snps,spear-ahci + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + clocks: + description: + Basic DWC AHCI SATA clock sources like application AXI/AHB BIU clock + and embedded PHYs reference clock together with vendor-specific set + of clocks. + minItems: 1 + maxItems: 4 + + clock-names: + contains: + anyOf: + - description: Application AXI/AHB BIU clock source + enum: + - aclk + - sata + - description: SATA Ports reference clock + enum: + - ref + - sata_ref + + resets: + description: + At least basic core and application clock domains reset is normally + supported by the DWC AHCI SATA controller. Some platform specific + clocks can be also specified though. + + reset-names: + contains: + description: Core and application clock domains reset control + const: arst + +patternProperties: + "^sata-port@[0-9a-e]$": + type: object + + properties: + reg: + minimum: 0 + maximum: 7 + + snps,tx-ts-max: + $ref: /schemas/types.yaml#/definitions/uint32 + description: Maximal size of Tx DMA transactions in FIFO words + minimum: 1 + maximum: 1024 + + snps,rx-ts-max: + $ref: /schemas/types.yaml#/definitions/uint32 + description: Maximal size of Rx DMA transactions in FIFO words + minimum: 1 + maximum: 1024 + +required: + - compatible + - reg + - interrupts + +unevaluatedProperties: false + +examples: + - | + #include <dt-bindings/interrupt-controller/arm-gic.h> + + sata@122f0000 { + compatible = "snps,dwc-ahci"; + reg = <0x122F0000 0x1ff>; + #address-cells = <1>; + #size-cells = <0>; + + interrupts = <GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH>; + + clocks = <&clock1>, <&clock2>; + clock-names = "aclk", "ref"; + + phys = <&sata_phy>; + phy-names = "sata-phy"; + + ports-implemented = <0x1>; + + sata-port@0 { + reg = <0>; + + hba-fbscp; + snps,tx-ts-max = <512>; + snps,tx-rs-max = <512>; + }; + }; +... -- 2.35.1
