[PATCH 11/21] ata: libahci: Extend port-cmd flags set with port capabilities

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Currently not all of the Port-specific capabilities listed in the
PORT_CMD-enumeration. Let's extend that set with the Cold Presence
Detection and Mechanical Presence Switch attached to the Port flags [1] so
to closeup the set of the platform-specific port-capabilities flags.  Note
these flags are supposed to be set by the platform firmware if there is
one. Alternatively as we are about to do they can be set by means of the
OF properties.

While at it replace PORT_IRQ_DEV_ILCK with PORT_IRQ_DEV_MPS and fix the
comment there. In accordance with [2] that IRQ flag is supposed to
indicate the state of the signal coming from the Mechanical Presence
Switch.

[1] Serial ATA AHCI 1.3.1 Specification, p.27
[2] Serial ATA AHCI 1.3.1 Specification, p.7

Signed-off-by: Serge Semin <Sergey.Semin@xxxxxxxxxxxxxxxxxxxx>
---
 drivers/ata/ahci.h | 7 ++++++-
 1 file changed, 6 insertions(+), 1 deletion(-)

diff --git a/drivers/ata/ahci.h b/drivers/ata/ahci.h
index 0b1d5c24cb8c..04690b4168a3 100644
--- a/drivers/ata/ahci.h
+++ b/drivers/ata/ahci.h
@@ -138,7 +138,7 @@ enum {
 	PORT_IRQ_BAD_PMP	= (1 << 23), /* incorrect port multiplier */
 
 	PORT_IRQ_PHYRDY		= (1 << 22), /* PhyRdy changed */
-	PORT_IRQ_DEV_ILCK	= (1 << 7), /* device interlock */
+	PORT_IRQ_DMPS		= (1 << 7), /* mechanical presence status */
 	PORT_IRQ_CONNECT	= (1 << 6), /* port connect change status */
 	PORT_IRQ_SG_DONE	= (1 << 5), /* descriptor processed */
 	PORT_IRQ_UNK_FIS	= (1 << 4), /* unknown FIS rx'd */
@@ -166,6 +166,8 @@ enum {
 	PORT_CMD_ATAPI		= (1 << 24), /* Device is ATAPI */
 	PORT_CMD_FBSCP		= (1 << 22), /* FBS Capable Port */
 	PORT_CMD_ESP		= (1 << 21), /* External Sata Port */
+	PORT_CMD_CPD		= (1 << 20), /* Cold Presence Detection */
+	PORT_CMD_MPSP		= (1 << 19), /* Mechanical Presence Switch */
 	PORT_CMD_HPCP		= (1 << 18), /* HotPlug Capable Port */
 	PORT_CMD_PMP		= (1 << 17), /* PMP attached */
 	PORT_CMD_LIST_ON	= (1 << 15), /* cmd list DMA engine running */
@@ -181,6 +183,9 @@ enum {
 	PORT_CMD_ICC_PARTIAL	= (0x2 << 28), /* Put i/f in partial state */
 	PORT_CMD_ICC_SLUMBER	= (0x6 << 28), /* Put i/f in slumber state */
 
+	PORT_CMD_CAP		= PORT_CMD_HPCP | PORT_CMD_MPSP |
+				  PORT_CMD_CPD | PORT_CMD_ESP | PORT_CMD_FBSCP,
+
 	/* PORT_FBS bits */
 	PORT_FBS_DWE_OFFSET	= 16, /* FBS device with error offset */
 	PORT_FBS_ADO_OFFSET	= 12, /* FBS active dev optimization offset */
-- 
2.35.1




[Index of Archives]     [Linux Filesystems]     [Linux SCSI]     [Linux RAID]     [Git]     [Kernel Newbies]     [Linux Newbie]     [Security]     [Netfilter]     [Bugtraq]     [Yosemite News]     [MIPS Linux]     [ARM Linux]     [Linux Security]     [Samba]     [Device Mapper]

  Powered by Linux