Dear Linux folks,
AMD Ryzen devices come with two SATA controllers:
$ lspci -nn | grep SATA
01:00.1 SATA controller [0106]: Advanced Micro Devices, Inc. [AMD]
300 Series Chipset SATA Controller [1022:43b7] (rev 02)
07:00.2 SATA controller [0106]: Advanced Micro Devices, Inc. [AMD]
FCH SATA Controller [AHCI mode] [1022:7901] (rev 51)
lsscsi [1] in verbose mode shows the controller a disk is actually
attached to.
$ lsscsi -v
[0:0:0:0] disk ATA ST500LM021-1KJ15 SDM1 /dev/sda
dir: /sys/bus/scsi/devices/0:0:0:0
[/sys/devices/pci0000:00/0000:00:01.3/0000:01:00.1/ata1/host0/target0:0:0/0:0:0:0]
For analysis and bug reports, it’d be great if the Linux kernel log
would contain that information too. But I am unable to find it. Is it
present?
[ 0.426850] calling ahci_pci_driver_init+0x0/0x1a @ 1
[ 0.426869] ahci 0000:01:00.1: version 3.0
[ 0.426970] ahci 0000:01:00.1: SSS flag set, parallel bus scan
disabled
[ 0.427004] ahci 0000:01:00.1: AHCI 0001.0301 32 slots 8 ports 6
Gbps 0x33 impl SATA mode
[ 0.427008] ahci 0000:01:00.1: flags: 64bit ncq sntf stag pm led
clo only pmp pio slum part sxs deso sadm sds apst
[ 0.427412] scsi host0: ahci
[ 0.427493] scsi host1: ahci
[ 0.427569] scsi host2: ahci
[ 0.427653] scsi host3: ahci
[ 0.427728] scsi host4: ahci
[ 0.427801] scsi host5: ahci
[ 0.427876] scsi host6: ahci
[ 0.427950] scsi host7: ahci
[ 0.427978] ata1: SATA max UDMA/133 abar m131072@0xf0600000 port
0xf0600100 irq 36
[ 0.427982] ata2: SATA max UDMA/133 abar m131072@0xf0600000 port
0xf0600180 irq 36
[ 0.427985] ata3: DUMMY
[ 0.427986] ata4: DUMMY
[ 0.427988] ata5: SATA max UDMA/133 abar m131072@0xf0600000 port
0xf0600300 irq 36
[ 0.427991] ata6: SATA max UDMA/133 abar m131072@0xf0600000 port
0xf0600380 irq 36
[ 0.427994] ata7: DUMMY
[ 0.427995] ata8: DUMMY
[ 0.428015] ata1: hard resetting link
[ 0.428116] ahci 0000:07:00.2: AHCI 0001.0301 32 slots 1 ports 6
Gbps 0x1 impl SATA mode
[ 0.428124] ahci 0000:07:00.2: flags: 64bit ncq sntf ilck pm led
clo only pmp fbs pio slum part
[ 0.428250] scsi host8: ahci
[ 0.428278] ata9: SATA max UDMA/133 abar m4096@0xf0108000 port
0xf0108100 irq 38
[ 0.428295] initcall ahci_pci_driver_init+0x0/0x1a returned 0
after 1409 usecs
[…]
[ 0.428316] ata9: hard resetting link
[ 0.532308] ata9: SATA link down (SStatus 0 SControl 300)
[ 0.696316] ata1: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
[ 0.725963] ata1.00: ATA-8: ST500LM021-1KJ152, 0005SDM1, max
UDMA/133
[ 0.725982] ata1.00: 976773168 sectors, multi 16: LBA48 NCQ
(depth 32)
[ 0.764845] ata1.00: configured for UDMA/133
Can you think of a way and log format, what controller the disk is
actually attached to?
[ 0.765133] ata2: hard resetting link
[ 0.868330] ata2: SATA link down (SStatus 0 SControl 300)
[ 0.868965] ata5: hard resetting link
[ 0.973337] ata5: SATA link down (SStatus 0 SControl 300)
[ 0.973910] ata6: hard resetting link
[ 1.077832] ata6: SATA link down (SStatus 0 SControl 300)
Kind regards,
Paul
[1]: https://sg.danny.cz/scsi/lsscsi.html
