Add Shuttle EPAT/EPEZ protocol driver.
Signed-off-by: Ondrej Zary <linux@xxxxxxx>
---
drivers/ata/pata_parport/Kconfig | 12 ++
drivers/ata/pata_parport/Makefile | 1 +
drivers/ata/pata_parport/epat.c | 320 ++++++++++++++++++++++++++++++
3 files changed, 333 insertions(+)
create mode 100644 drivers/ata/pata_parport/epat.c
diff --git a/drivers/ata/pata_parport/Kconfig b/drivers/ata/pata_parport/Kconfig
index a03c626e4e6c..6c218486c3b8 100644
--- a/drivers/ata/pata_parport/Kconfig
+++ b/drivers/ata/pata_parport/Kconfig
@@ -97,3 +97,15 @@ config PATA_PARPORT_FIT3
may answer Y here to build in the protocol driver, otherwise you
should answer M to build it as a loadable module. The module will be
called fit3.
+
+config PATA_PARPORT_EPAT
+ tristate "Shuttle EPAT/EPEZ protocol"
+ depends on PATA_PARPORT
+ help
+ This option enables support for the EPAT parallel port IDE protocol.
+ EPAT is a parallel port IDE adapter manufactured by Shuttle
+ Technology and widely used in devices from major vendors such as
+ Hewlett-Packard, SyQuest, Imation and Avatar. If you chose to build
+ PATA_PARPORT support into your kernel, you may answer Y here to build in
+ the protocol driver, otherwise you should answer M to build it as a
+ loadable module. The module will be called epat.
diff --git a/drivers/ata/pata_parport/Makefile b/drivers/ata/pata_parport/Makefile
index 140f6f142eaa..459307f4a096 100644
--- a/drivers/ata/pata_parport/Makefile
+++ b/drivers/ata/pata_parport/Makefile
@@ -14,3 +14,4 @@ obj-$(CONFIG_PATA_PARPORT_COMM) += comm.o
obj-$(CONFIG_PATA_PARPORT_DSTR) += dstr.o
obj-$(CONFIG_PATA_PARPORT_FIT2) += fit2.o
obj-$(CONFIG_PATA_PARPORT_FIT3) += fit3.o
+obj-$(CONFIG_PATA_PARPORT_EPAT) += epat.o
diff --git a/drivers/ata/pata_parport/epat.c b/drivers/ata/pata_parport/epat.c
new file mode 100644
index 000000000000..2103e272c82a
--- /dev/null
+++ b/drivers/ata/pata_parport/epat.c
@@ -0,0 +1,320 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * epat.c (c) 1997-8 Grant R. Guenther <grant@xxxxxxxxxx>
+ * Under the terms of the GNU General Public License.
+ *
+ * This is the low level protocol driver for the EPAT parallel
+ * to IDE adapter from Shuttle Technologies. This adapter is
+ * used in many popular parallel port disk products such as the
+ * SyQuest EZ drives, the Avatar Shark and the Imation SuperDisk.
+ */
+
+#include <linux/module.h>
+#include <linux/init.h>
+#include <linux/delay.h>
+#include <linux/kernel.h>
+#include <linux/types.h>
+#include <linux/wait.h>
+#include <linux/io.h>
+
+#include "pata_parport.h"
+
+#define j44(a, b) (((a >> 4) & 0x0f) + (b & 0xf0))
+#define j53(a, b) (((a >> 3) & 0x1f) + ((b << 4) & 0xe0))
+
+static int epatc8 = 1;
+module_param(epatc8, int, 0);
+MODULE_PARM_DESC(epatc8, "Support for the Shuttle EP1284 chip, used in any recent Imation SuperDisk (LS-120) drive (0=off, 1=on [default])");
+
+/* cont = 0 IDE register file
+ * cont = 1 IDE control registers
+ * cont = 2 internal EPAT registers
+ */
+
+static int cont_map[3] = { 0x18, 0x10, 0 };
+
+static void epat_write_regr(struct pi_adapter *pi, int cont, int regr, int val)
+{
+ int r = regr + cont_map[cont];
+
+ switch (pi->mode) {
+ case 0:
+ case 1:
+ case 2:
+ w0(0x60+r); w2(1); w0(val); w2(4);
+ break;
+ case 3:
+ case 4:
+ case 5:
+ w3(0x40+r); w4(val);
+ break;
+ }
+}
+
+static int epat_read_regr(struct pi_adapter *pi, int cont, int regr)
+{
+ int a, b, r;
+
+ r = regr + cont_map[cont];
+
+ switch (pi->mode) {
+ case 0:
+ w0(r); w2(1); w2(3);
+ a = r1(); w2(4); b = r1();
+ return j44(a, b);
+ case 1:
+ w0(0x40+r); w2(1); w2(4);
+ a = r1(); b = r2(); w0(0xff);
+ return j53(a, b);
+ case 2:
+ w0(0x20+r); w2(1); w2(0x25);
+ a = r0(); w2(4);
+ return a;
+ case 3:
+ case 4:
+ case 5:
+ w3(r); w2(0x24); a = r4(); w2(4);
+ return a;
+ }
+ return -1; /* never gets here */
+}
+
+static void epat_read_block(struct pi_adapter *pi, char *buf, int count)
+{
+ int k, ph, a, b;
+
+ switch (pi->mode) {
+ case 0:
+ w0(7); w2(1); w2(3); w0(0xff);
+ ph = 0;
+ for (k = 0; k < count; k++) {
+ if (k == count-1)
+ w0(0xfd);
+ w2(6 + ph); a = r1();
+ if (a & 8)
+ b = a;
+ else {
+ w2(4+ph); b = r1();
+ }
+ buf[k] = j44(a, b);
+ ph = 1 - ph;
+ }
+ w0(0); w2(4);
+ break;
+ case 1:
+ w0(0x47); w2(1); w2(5); w0(0xff);
+ ph = 0;
+ for (k = 0; k < count; k++) {
+ if (k == count - 1)
+ w0(0xfd);
+ w2(4 + ph);
+ a = r1(); b = r2();
+ buf[k] = j53(a, b);
+ ph = 1 - ph;
+ }
+ w0(0); w2(4);
+ break;
+ case 2:
+ w0(0x27); w2(1); w2(0x25); w0(0);
+ ph = 0;
+ for (k = 0; k < count-1; k++) {
+ w2(0x24 + ph);
+ buf[k] = r0();
+ ph = 1 - ph;
+ }
+ w2(0x26); w2(0x27); buf[count - 1] = r0();
+ w2(0x25); w2(4);
+ break;
+ case 3:
+ w3(0x80); w2(0x24);
+ for (k = 0; k < count - 1; k++)
+ buf[k] = r4();
+ w2(4); w3(0xa0); w2(0x24); buf[count - 1] = r4();
+ w2(4);
+ break;
+ case 4:
+ w3(0x80); w2(0x24);
+ for (k = 0; k < (count / 2) - 1; k++)
+ ((u16 *)buf)[k] = r4w();
+ buf[count - 2] = r4();
+ w2(4); w3(0xa0); w2(0x24); buf[count - 1] = r4();
+ w2(4);
+ break;
+ case 5:
+ w3(0x80); w2(0x24);
+ for (k = 0; k < (count / 4) - 1; k++)
+ ((u32 *)buf)[k] = r4l();
+ for (k = count - 4; k < count - 1; k++)
+ buf[k] = r4();
+ w2(4); w3(0xa0); w2(0x24); buf[count - 1] = r4();
+ w2(4);
+ break;
+ }
+}
+
+static void epat_write_block(struct pi_adapter *pi, char *buf, int count)
+{
+ int ph, k;
+
+ switch (pi->mode) {
+ case 0:
+ case 1:
+ case 2:
+ w0(0x67); w2(1); w2(5);
+ ph = 0;
+ for (k = 0; k < count; k++) {
+ w0(buf[k]);
+ w2(4+ph);
+ ph = 1 - ph;
+ }
+ w2(7); w2(4);
+ break;
+ case 3:
+ w3(0xc0);
+ for (k = 0; k < count; k++)
+ w4(buf[k]);
+ w2(4);
+ break;
+ case 4:
+ w3(0xc0);
+ for (k = 0; k < (count/2); k++)
+ w4w(((u16 *)buf)[k]);
+ w2(4);
+ break;
+ case 5:
+ w3(0xc0);
+ for (k = 0; k < (count/4); k++)
+ w4l(((u32 *)buf)[k]);
+ w2(4);
+ break;
+ }
+}
+
+/* these macros access the EPAT registers in native addressing */
+#define WR(r, v) epat_write_regr(pi, 2, r, v)
+#define RR(r) (epat_read_regr(pi, 2, r))
+
+/* and these access the IDE task file */
+#define WRi(r, v) epat_write_regr(pi, 0, r, v)
+#define RRi(r) (epat_read_regr(pi, 0, r))
+
+/* FIXME: the CPP stuff should be fixed to handle multiple EPATs on a chain */
+#define CPP(x) do { w2(4); w0(0x22); w0(0xaa); w0(0x55); w0(0); w0(0xff);\
+ w0(0x87); w0(0x78); w0(x); w2(4); w2(5); w2(4); w0(0xff);\
+ } while (0)
+
+static void epat_connect(struct pi_adapter *pi)
+{
+ pi->saved_r0 = r0();
+ pi->saved_r2 = r2();
+
+ /* Initialize the chip */
+ CPP(0);
+
+ if (epatc8) {
+ CPP(0x40); CPP(0xe0);
+ w0(0); w2(1); w2(4);
+ WR(0x8, 0x12); WR(0xc, 0x14); WR(0x12, 0x10);
+ WR(0xe, 0xf); WR(0xf, 4);
+ /* WR(0xe, 0xa); WR(0xf, 4); */
+ WR(0xe, 0xd); WR(0xf, 0);
+ /* CPP(0x30); */
+ }
+
+ /* Connect to the chip */
+ CPP(0xe0);
+ w0(0); w2(1); w2(4); /* Idle into SPP */
+ if (pi->mode >= 3) {
+ w0(0); w2(1); w2(4); w2(0xc);
+ /* Request EPP */
+ w0(0x40); w2(6); w2(7); w2(4); w2(0xc); w2(4);
+ }
+
+ if (!epatc8) {
+ WR(8, 0x10); WR(0xc, 0x14); WR(0xa, 0x38); WR(0x12, 0x10);
+ }
+}
+
+static void epat_disconnect(struct pi_adapter *pi)
+{
+ CPP(0x30);
+ w0(pi->saved_r0);
+ w2(pi->saved_r2);
+}
+
+static int epat_test_proto(struct pi_adapter *pi, char *scratch, int verbose)
+{
+ int k, j, f, cc;
+ int e[2] = { 0, 0 };
+
+ epat_connect(pi);
+ cc = RR(0xd);
+ epat_disconnect(pi);
+
+ epat_connect(pi);
+ for (j = 0; j < 2; j++) {
+ WRi(6, 0xa0 + j * 0x10);
+ for (k = 0; k < 256; k++) {
+ WRi(2, k ^ 0xaa);
+ WRi(3, k ^ 0x55);
+ if (RRi(2) != (k ^ 0xaa))
+ e[j]++;
+ }
+ }
+ epat_disconnect(pi);
+
+ f = 0;
+ epat_connect(pi);
+ WR(0x13, 1); WR(0x13, 0); WR(0xa, 0x11);
+ epat_read_block(pi, scratch, 512);
+
+ for (k = 0; k < 256; k++) {
+ if ((scratch[2 * k] & 0xff) != k)
+ f++;
+ if ((scratch[2 * k + 1] & 0xff) != (0xff - k))
+ f++;
+ }
+ epat_disconnect(pi);
+
+ if (verbose)
+ dev_info(&pi->dev, "epat: port 0x%x, mode %d, ccr %x, test=(%d,%d,%d)\n",
+ pi->port, pi->mode, cc, e[0], e[1], f);
+
+ return (e[0] && e[1]) || f;
+}
+
+static void epat_log_adapter(struct pi_adapter *pi, char *scratch, int verbose)
+{
+ int ver;
+ static char * const mode_string[] = {
+ "4-bit", "5/3", "8-bit", "EPP-8", "EPP-16", "EPP-32" };
+
+ epat_connect(pi);
+ WR(0xa, 0x38); /* read the version code */
+ ver = RR(0xb);
+ epat_disconnect(pi);
+
+ dev_info(&pi->dev, "epat, Shuttle EPAT chip %x at 0x%x, mode %d (%s), delay %d\n",
+ ver, pi->port, pi->mode, mode_string[pi->mode], pi->delay);
+}
+
+static struct pi_protocol epat = {
+ .owner = THIS_MODULE,
+ .name = "epat",
+ .max_mode = 6,
+ .epp_first = 3,
+ .default_delay = 1,
+ .max_units = 1,
+ .write_regr = epat_write_regr,
+ .read_regr = epat_read_regr,
+ .write_block = epat_write_block,
+ .read_block = epat_read_block,
+ .connect = epat_connect,
+ .disconnect = epat_disconnect,
+ .test_proto = epat_test_proto,
+ .log_adapter = epat_log_adapter,
+ .sht = { PATA_PARPORT_SHT("pata_parport-epat") },
+};
+
+MODULE_LICENSE("GPL");
+module_pata_parport_driver(epat);
--
Ondrej Zary
