Hi Rob, thanks for review, have prepared the changes based on yours and krzysztof comments https://github.com/frank-w/BPI-R2-4.14/commits/5.17-next-20220225 (just ignore the top 2 commits) i thought i had a size-cells-error, but did not get them again after reverting this part, seems they are fixed by inclusion of the sata-common binding > Gesendet: Mittwoch, 02. März 2022 um 19:14 Uhr > Von: "Rob Herring" <robh@xxxxxxxxxx> > An: "Frank Wunderlich" <linux@xxxxxxxxx> > On Tue, Mar 01, 2022 at 04:24:17PM +0100, Frank Wunderlich wrote: > > From: Frank Wunderlich <frank-w@xxxxxxxxxxxxxxx> > > diff --git a/Documentation/devicetree/bindings/ata/ahci-platform.yaml b/Documentation/devicetree/bindings/ata/ahci-platform.yaml > > new file mode 100644 > > index 000000000000..cf67ddfc6afb > > --- /dev/null > > +++ b/Documentation/devicetree/bindings/ata/ahci-platform.yaml > > @@ -0,0 +1,162 @@ > > +# SPDX-License-Identifier: GPL-2.0 > > +%YAML 1.2 > > +--- > > +$id: http://devicetree.org/schemas/ata/ahci-platform.yaml# > > +$schema: http://devicetree.org/meta-schemas/core.yaml# > > + > > +title: AHCI SATA Controller > > blank line. done > > +description: > > + SATA nodes are defined to describe on-chip Serial ATA controllers. > > + Each SATA controller should have its own node. > > + > > + It is possible, but not required, to represent each port as a sub-node. > > + It allows to enable each port independently when dealing with multiple > > + PHYs. > > You need a '|' after 'description' if you want to maintain the > paragraphs. ok added | to all multiline descriptions > > + > > +maintainers: > > + - Hans de Goede <hdegoede@xxxxxxxxxx> > > + - Jens Axboe <axboe@xxxxxxxxx> > > + > > +allOf: > > +- $ref: "sata-common.yaml#" > > + > > +properties: > > + compatible: > > + oneOf: > > + - items: > > + - enum: > > + - brcm,iproc-ahci > > + - marvell,armada-8k-ahci > > + - marvell,berlin2q-ahci > > + - const: generic-ahci > > + - enum: > > + - brcm,iproc-ahci > > + - cavium,octeon-7130-ahci > > + - hisilicon,hisi-ahci > > + - ibm,476gtr-ahci > > + - marvell,armada-3700-ahci > > + - marvell,armada-380-ahci > > + - snps,dwc-ahci > > + - snps,spear-ahci > > Install yamllint and run 'make dt_binding_check'. It's going to > complain about the indentation. you're right, i had no yamllint installed, so i have not seen these indention errors > > + ahci-supply: > > + description: > > + regulator for AHCI controller > > + > > + clock-names: > > Group with 'clocks' ok, already done in my tree because of krzysztofs comment > > + ports-implemented: > > + $ref: '/schemas/types.yaml#/definitions/uint32' > > + description: > > + Mask that indicates which ports that the HBA supports > > + are available for software to use. Useful if PORTS_IMPL > > + is not programmed by the BIOS, which is true with > > + some embedded SoCs. > > + maxItems: 1 > > A uint32 is only ever 1 item. Drop. > > IIRC, isn't the max here 0xff? Add constraints. i've found it only set to 0x1 so i have currently set the maximum to 0x1, is this ok? If some higher value is needed binding needs to be touched... > > + > > + reg-names: > > + maxItems: 1 > > Group with 'reg'. ok > > +patternProperties: > > + "^sata-port@[0-9a-f]+$": > > + type: object > > additionalProperties: false ok added to my tree and needed to add phy-names because some marvell boards using this arch/arm64/boot/dts/marvell/armada-8040-mcbin-singleshot.dt.yaml: sata@540000: sata-port@1: 'phy-names' does not match any of the regexes: 'pinctrl-[0-9]+' now i have only the marvell-errors about incomplete sata-port subnode (without phy/target-supply) like i mention in the patch...how to proceed with this? regards Frank
