[PATCH v2 3/3] ata: ahci: Rename CONFIG_SATA_LPM_MOBILE_POLICY configuration item

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



`CONFIG_SATA_LPM_MOBILE_POLICY` reflects a configuration to apply only to
mobile chipsets.  As some desktop boards may want to use this policy by
default as well, rename the configuration item to `SATA_LPM_POLICY`.

Signed-off-by: Mario Limonciello <mario.limonciello@xxxxxxx>
---
changes from v1->v2:
 * Reword documentation in Kconfig
 * Change configuration item to match earlier patches

 drivers/ata/Kconfig | 6 +++---
 drivers/ata/ahci.c  | 2 +-
 drivers/ata/ahci.h  | 2 +-
 3 files changed, 5 insertions(+), 5 deletions(-)

diff --git a/drivers/ata/Kconfig b/drivers/ata/Kconfig
index cb54631fd950..cb9e71b4ca4d 100644
--- a/drivers/ata/Kconfig
+++ b/drivers/ata/Kconfig
@@ -115,14 +115,14 @@ config SATA_AHCI
 
 	  If unsure, say N.
 
-config SATA_MOBILE_LPM_POLICY
-	int "Default SATA Link Power Management policy for mobile chipsets"
+config SATA_LPM_POLICY
+	int "Default SATA Link Power Management policy for low power chipsets"
 	range 0 4
 	default 0
 	depends on SATA_AHCI
 	help
 	  Select the Default SATA Link Power Management (LPM) policy to use
-	  for mobile / laptop variants of chipsets / "South Bridges".
+	  for chipsets / "South Bridges" designated as supporting low power.
 
 	  The value set has the following meanings:
 		0 => Keep firmware settings
diff --git a/drivers/ata/ahci.c b/drivers/ata/ahci.c
index a77e8154b5f0..b84ba95be84a 100644
--- a/drivers/ata/ahci.c
+++ b/drivers/ata/ahci.c
@@ -1592,7 +1592,7 @@ static int ahci_init_msi(struct pci_dev *pdev, unsigned int n_ports,
 static void ahci_update_initial_lpm_policy(struct ata_port *ap,
 					   struct ahci_host_priv *hpriv)
 {
-	int policy = CONFIG_SATA_MOBILE_LPM_POLICY;
+	int policy = CONFIG_SATA_LPM_POLICY;
 
 
 	/* Ignore processing for chipsets that don't use policy */
diff --git a/drivers/ata/ahci.h b/drivers/ata/ahci.h
index 1ad48e2fe573..5badbaca05a0 100644
--- a/drivers/ata/ahci.h
+++ b/drivers/ata/ahci.h
@@ -236,7 +236,7 @@ enum {
 	AHCI_HFLAG_NO_WRITE_TO_RO	= (1 << 24), /* don't write to read
 							only registers */
 	AHCI_HFLAG_USE_LPM_POLICY	= (1 << 25), /* chipset that should use
-							SATA_MOBILE_LPM_POLICY
+							SATA_LPM_POLICY
 							as default lpm_policy */
 	AHCI_HFLAG_SUSPEND_PHYS		= (1 << 26), /* handle PHYs during
 							suspend/resume */
-- 
2.34.1




[Index of Archives]     [Linux Filesystems]     [Linux SCSI]     [Linux RAID]     [Git]     [Kernel Newbies]     [Linux Newbie]     [Security]     [Netfilter]     [Bugtraq]     [Yosemite News]     [MIPS Linux]     [ARM Linux]     [Linux Security]     [Samba]     [Device Mapper]

  Powered by Linux