This allows m68k q40 systems to switch from the deprecated IDE subsystem
to libata.
Enhance the byte-swapping falconide and pata_falcon platform drivers to
accept an irq resource, for use on q40. Atari ST-DMA IRQ arrangements seem
to co-exist with q40 IRQ arrangements without too much mess.
The new IO resources were added solely for the purpose of making
request_region() reservations identical to those made by q40ide: these
regions aren't used for actual IO.
Cc: Michael Schmitz <schmitzmic@xxxxxxxxx>
Cc: Richard Zidlicky <rz@xxxxxxxxxxxxxx>
Reviewed-and-tested-by: Michael Schmitz <schmitzmic@xxxxxxxxx>
Signed-off-by: Finn Thain <fthain@xxxxxxxxxxxxxx>
---
Note that q40ide, falconide and pata_falcon all use the same accessors
(raw_insw_swapw, raw_insw, raw_outsw_swapw, raw_outsw) and hence all
three drivers are affected by the bug relating to CONFIG_ISA and
CONFIG_ATARI_ROM_ISA which Michael has been working on recently.
This patch doesn't make that issue any better or worse.
---
arch/m68k/atari/config.c | 12 +--
arch/m68k/configs/multi_defconfig | 1 -
arch/m68k/configs/q40_defconfig | 2 +-
arch/m68k/q40/config.c | 37 +++++--
drivers/ata/Kconfig | 6 +-
drivers/ata/pata_falcon.c | 62 ++++++++---
drivers/ide/Kconfig | 18 +---
drivers/ide/Makefile | 1 -
drivers/ide/falconide.c | 75 ++++++++-----
drivers/ide/q40ide.c | 168 ------------------------------
10 files changed, 137 insertions(+), 245 deletions(-)
delete mode 100644 drivers/ide/q40ide.c
diff --git a/arch/m68k/atari/config.c b/arch/m68k/atari/config.c
index 44f9b5216ac9..261a0f57cc9a 100644
--- a/arch/m68k/atari/config.c
+++ b/arch/m68k/atari/config.c
@@ -875,16 +875,8 @@ static const struct resource atari_scsi_tt_rsrc[] __initconst = {
#define FALCON_IDE_BASE 0xfff00000
static const struct resource atari_falconide_rsrc[] __initconst = {
- {
- .flags = IORESOURCE_MEM,
- .start = FALCON_IDE_BASE,
- .end = FALCON_IDE_BASE + 0x39,
- },
- {
- .flags = IORESOURCE_IRQ,
- .start = IRQ_MFP_FSCSI,
- .end = IRQ_MFP_FSCSI,
- },
+ DEFINE_RES_MEM(FALCON_IDE_BASE, 0x38),
+ DEFINE_RES_MEM(FALCON_IDE_BASE + 0x38, 2),
};
int __init atari_platform_init(void)
diff --git a/arch/m68k/configs/multi_defconfig b/arch/m68k/configs/multi_defconfig
index 9ee6d2b4d1f4..f4cafed671cb 100644
--- a/arch/m68k/configs/multi_defconfig
+++ b/arch/m68k/configs/multi_defconfig
@@ -351,7 +351,6 @@ CONFIG_BLK_DEV_PLATFORM=y
CONFIG_BLK_DEV_GAYLE=y
CONFIG_BLK_DEV_BUDDHA=y
CONFIG_BLK_DEV_FALCON_IDE=y
-CONFIG_BLK_DEV_Q40IDE=y
CONFIG_RAID_ATTRS=m
CONFIG_SCSI=y
CONFIG_BLK_DEV_SD=y
diff --git a/arch/m68k/configs/q40_defconfig b/arch/m68k/configs/q40_defconfig
index 3ae421cb24a4..2c25b4096397 100644
--- a/arch/m68k/configs/q40_defconfig
+++ b/arch/m68k/configs/q40_defconfig
@@ -317,7 +317,7 @@ CONFIG_DUMMY_IRQ=m
CONFIG_IDE=y
CONFIG_IDE_GD_ATAPI=y
CONFIG_BLK_DEV_IDECD=y
-CONFIG_BLK_DEV_Q40IDE=y
+CONFIG_BLK_DEV_FALCON_IDE=y
CONFIG_RAID_ATTRS=m
CONFIG_SCSI=y
CONFIG_BLK_DEV_SD=y
diff --git a/arch/m68k/q40/config.c b/arch/m68k/q40/config.c
index d6a423875231..5caf1e5be1c2 100644
--- a/arch/m68k/q40/config.c
+++ b/arch/m68k/q40/config.c
@@ -286,14 +286,39 @@ static int q40_set_rtc_pll(struct rtc_pll_info *pll)
return -EINVAL;
}
-static __init int q40_add_kbd_device(void)
-{
- struct platform_device *pdev;
+#define PCIDE_BASE1 0x1f0
+#define PCIDE_BASE2 0x170
+#define PCIDE_CTL 0x206
+
+static const struct resource q40_pata_rsrc_0[] __initconst = {
+ DEFINE_RES_MEM(q40_isa_io_base + PCIDE_BASE1 * 4, 0x38),
+ DEFINE_RES_MEM(q40_isa_io_base + (PCIDE_BASE1 + PCIDE_CTL) * 4, 2),
+ DEFINE_RES_IO(PCIDE_BASE1, 8),
+ DEFINE_RES_IO(PCIDE_BASE1 + PCIDE_CTL, 1),
+ DEFINE_RES_IRQ(14),
+};
+static const struct resource q40_pata_rsrc_1[] __initconst = {
+ DEFINE_RES_MEM(q40_isa_io_base + PCIDE_BASE2 * 4, 0x38),
+ DEFINE_RES_MEM(q40_isa_io_base + (PCIDE_BASE2 + PCIDE_CTL) * 4, 2),
+ DEFINE_RES_IO(PCIDE_BASE2, 8),
+ DEFINE_RES_IO(PCIDE_BASE2 + PCIDE_CTL, 1),
+ DEFINE_RES_IRQ(15),
+};
+
+static __init int q40_platform_init(void)
+{
if (!MACH_IS_Q40)
return -ENODEV;
- pdev = platform_device_register_simple("q40kbd", -1, NULL, 0);
- return PTR_ERR_OR_ZERO(pdev);
+ platform_device_register_simple("q40kbd", -1, NULL, 0);
+
+ platform_device_register_simple("atari-falcon-ide", 0, q40_pata_rsrc_0,
+ ARRAY_SIZE(q40_pata_rsrc_0));
+
+ platform_device_register_simple("atari-falcon-ide", 1, q40_pata_rsrc_1,
+ ARRAY_SIZE(q40_pata_rsrc_1));
+
+ return 0;
}
-arch_initcall(q40_add_kbd_device);
+arch_initcall(q40_platform_init);
diff --git a/drivers/ata/Kconfig b/drivers/ata/Kconfig
index 030cb32da980..b7a5abee2147 100644
--- a/drivers/ata/Kconfig
+++ b/drivers/ata/Kconfig
@@ -1015,11 +1015,11 @@ config PATA_CMD640_PCI
If unsure, say N.
config PATA_FALCON
- tristate "Atari Falcon PATA support"
- depends on M68K && ATARI
+ tristate "Atari Falcon and Q40/Q60 PATA support"
+ depends on M68K && (ATARI || Q40)
help
This option enables support for the on-board IDE
- interface on the Atari Falcon.
+ interface on the Atari Falcon and Q40/Q60.
If unsure, say N.
diff --git a/drivers/ata/pata_falcon.c b/drivers/ata/pata_falcon.c
index 27b0952fde6b..9d0dd8f4c21c 100644
--- a/drivers/ata/pata_falcon.c
+++ b/drivers/ata/pata_falcon.c
@@ -33,8 +33,6 @@
#define DRV_NAME "pata_falcon"
#define DRV_VERSION "0.1.0"
-#define ATA_HD_CONTROL 0x39
-
static struct scsi_host_template pata_falcon_sht = {
ATA_PIO_SHT(DRV_NAME),
};
@@ -121,23 +119,42 @@ static struct ata_port_operations pata_falcon_ops = {
static int __init pata_falcon_init_one(struct platform_device *pdev)
{
- struct resource *res;
+ struct resource *base_mem_res, *ctl_mem_res;
+ struct resource *base_res, *ctl_res, *irq_res;
struct ata_host *host;
struct ata_port *ap;
void __iomem *base;
+ int irq = 0;
- dev_info(&pdev->dev, "Atari Falcon PATA controller\n");
+ dev_info(&pdev->dev, "Atari Falcon and Q40/Q60 PATA controller\n");
- res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
- if (!res)
- return -ENODEV;
+ base_res = platform_get_resource(pdev, IORESOURCE_IO, 0);
+ if (base_res && !devm_request_region(&pdev->dev, base_res->start,
+ resource_size(base_res), DRV_NAME)) {
+ dev_err(&pdev->dev, "resources busy\n");
+ return -EBUSY;
+ }
- if (!devm_request_mem_region(&pdev->dev, res->start,
- resource_size(res), DRV_NAME)) {
+ ctl_res = platform_get_resource(pdev, IORESOURCE_IO, 1);
+ if (ctl_res && !devm_request_region(&pdev->dev, ctl_res->start,
+ resource_size(ctl_res), DRV_NAME)) {
dev_err(&pdev->dev, "resources busy\n");
return -EBUSY;
}
+ base_mem_res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ if (!base_mem_res)
+ return -ENODEV;
+ if (!devm_request_mem_region(&pdev->dev, base_mem_res->start,
+ resource_size(base_mem_res), DRV_NAME)) {
+ dev_err(&pdev->dev, "resources busy\n");
+ return -EBUSY;
+ }
+
+ ctl_mem_res = platform_get_resource(pdev, IORESOURCE_MEM, 1);
+ if (!ctl_mem_res)
+ return -ENODEV;
+
/* allocate host */
host = ata_host_alloc(&pdev->dev, 1);
if (!host)
@@ -147,10 +164,10 @@ static int __init pata_falcon_init_one(struct platform_device *pdev)
ap->ops = &pata_falcon_ops;
ap->pio_mask = ATA_PIO4;
ap->flags |= ATA_FLAG_SLAVE_POSS | ATA_FLAG_NO_IORDY;
- ap->flags |= ATA_FLAG_PIO_POLLING;
- base = (void __iomem *)res->start;
- ap->ioaddr.data_addr = base;
+ base = (void __iomem *)base_mem_res->start;
+ /* N.B. this assumes data_addr will be used for word-sized I/O only */
+ ap->ioaddr.data_addr = base + 0 + 0 * 4;
ap->ioaddr.error_addr = base + 1 + 1 * 4;
ap->ioaddr.feature_addr = base + 1 + 1 * 4;
ap->ioaddr.nsect_addr = base + 1 + 2 * 4;
@@ -161,14 +178,25 @@ static int __init pata_falcon_init_one(struct platform_device *pdev)
ap->ioaddr.status_addr = base + 1 + 7 * 4;
ap->ioaddr.command_addr = base + 1 + 7 * 4;
- ap->ioaddr.altstatus_addr = base + ATA_HD_CONTROL;
- ap->ioaddr.ctl_addr = base + ATA_HD_CONTROL;
+ base = (void __iomem *)ctl_mem_res->start;
+ ap->ioaddr.altstatus_addr = base + 1;
+ ap->ioaddr.ctl_addr = base + 1;
- ata_port_desc(ap, "cmd 0x%lx ctl 0x%lx", (unsigned long)base,
- (unsigned long)base + ATA_HD_CONTROL);
+ ata_port_desc(ap, "cmd 0x%lx ctl 0x%lx",
+ (unsigned long)base_mem_res->start,
+ (unsigned long)ctl_mem_res->start);
+
+ irq_res = platform_get_resource(pdev, IORESOURCE_IRQ, 0);
+ if (irq_res && irq_res->start > 0) {
+ irq = irq_res->start;
+ } else {
+ ap->flags |= ATA_FLAG_PIO_POLLING;
+ ata_port_desc(ap, "no IRQ, using PIO polling");
+ }
/* activate */
- return ata_host_activate(host, 0, NULL, 0, &pata_falcon_sht);
+ return ata_host_activate(host, irq, irq ? ata_sff_interrupt : NULL,
+ IRQF_SHARED, &pata_falcon_sht);
}
static int __exit pata_falcon_remove_one(struct platform_device *pdev)
diff --git a/drivers/ide/Kconfig b/drivers/ide/Kconfig
index 8ce4a5878d0c..8af1ac69e5f8 100644
--- a/drivers/ide/Kconfig
+++ b/drivers/ide/Kconfig
@@ -731,21 +731,13 @@ config BLK_DEV_BUDDHA
to one of its IDE interfaces.
config BLK_DEV_FALCON_IDE
- tristate "Falcon IDE interface support"
- depends on ATARI
+ tristate "Falcon and Q40/Q60 IDE interface support"
+ depends on ATARI || Q40
help
This is the IDE driver for the on-board IDE interface on the Atari
- Falcon. Say Y if you have a Falcon and want to use IDE devices (hard
- disks, CD-ROM drives, etc.) that are connected to the on-board IDE
- interface.
-
-config BLK_DEV_Q40IDE
- tristate "Q40/Q60 IDE interface support"
- depends on Q40
- help
- Enable the on-board IDE controller in the Q40/Q60. This should
- normally be on; disable it only if you are running a custom hard
- drive subsystem through an expansion card.
+ Falcon and Q40/Q60. Say Y if you have such a machine and want to use
+ IDE devices (hard disks, CD-ROM drives, etc.) that are connected to
+ the on-board IDE interface.
config BLK_DEV_PALMCHIP_BK3710
tristate "Palmchip bk3710 IDE controller support"
diff --git a/drivers/ide/Makefile b/drivers/ide/Makefile
index 45a1c0463bed..991eb72a786b 100644
--- a/drivers/ide/Makefile
+++ b/drivers/ide/Makefile
@@ -29,7 +29,6 @@ obj-$(CONFIG_BLK_DEV_4DRIVES) += ide-4drives.o
obj-$(CONFIG_BLK_DEV_GAYLE) += gayle.o
obj-$(CONFIG_BLK_DEV_FALCON_IDE) += falconide.o
-obj-$(CONFIG_BLK_DEV_Q40IDE) += q40ide.o
obj-$(CONFIG_BLK_DEV_BUDDHA) += buddha.o
obj-$(CONFIG_BLK_DEV_AEC62XX) += aec62xx.o
diff --git a/drivers/ide/falconide.c b/drivers/ide/falconide.c
index bb86d84558d9..fce68412b3c9 100644
--- a/drivers/ide/falconide.c
+++ b/drivers/ide/falconide.c
@@ -25,12 +25,6 @@
#define DRV_NAME "falconide"
- /*
- * Offsets from base address
- */
-
-#define ATA_HD_CONTROL 0x39
-
/*
* falconide_intr_lock is used to obtain access to the IDE interrupt,
* which is shared between several drivers.
@@ -107,7 +101,8 @@ static const struct ide_port_info falconide_port_info = {
.chipset = ide_generic,
};
-static void __init falconide_setup_ports(struct ide_hw *hw, unsigned long base)
+static void __init falconide_setup_ports(struct ide_hw *hw, unsigned long base,
+ unsigned long ctl, int irq)
{
int i;
@@ -118,9 +113,9 @@ static void __init falconide_setup_ports(struct ide_hw *hw, unsigned long base)
for (i = 1; i < 8; i++)
hw->io_ports_array[i] = base + 1 + i * 4;
- hw->io_ports.ctl_addr = base + ATA_HD_CONTROL;
+ hw->io_ports.ctl_addr = ctl + 1;
- hw->irq = IRQ_MFP_IDE;
+ hw->irq = irq;
}
/*
@@ -129,37 +124,69 @@ static void __init falconide_setup_ports(struct ide_hw *hw, unsigned long base)
static int __init falconide_init(struct platform_device *pdev)
{
- struct resource *res;
+ struct resource *base_mem_res, *ctl_mem_res;
+ struct resource *base_res, *ctl_res, *irq_res;
struct ide_host *host;
struct ide_hw hw, *hws[] = { &hw };
- unsigned long base;
int rc;
+ int irq;
+
+ dev_info(&pdev->dev, "Atari Falcon and Q40/Q60 IDE controller\n");
+
+ base_res = platform_get_resource(pdev, IORESOURCE_IO, 0);
+ if (base_res && !devm_request_region(&pdev->dev, base_res->start,
+ resource_size(base_res), DRV_NAME)) {
+ dev_err(&pdev->dev, "resources busy\n");
+ return -EBUSY;
+ }
- dev_info(&pdev->dev, "Atari Falcon IDE controller\n");
+ ctl_res = platform_get_resource(pdev, IORESOURCE_IO, 0);
+ if (ctl_res && !devm_request_region(&pdev->dev, ctl_res->start,
+ resource_size(ctl_res), DRV_NAME)) {
+ dev_err(&pdev->dev, "resources busy\n");
+ return -EBUSY;
+ }
- res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
- if (!res)
+ base_mem_res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ if (!base_mem_res)
return -ENODEV;
- if (!devm_request_mem_region(&pdev->dev, res->start,
- resource_size(res), DRV_NAME)) {
+ if (!devm_request_mem_region(&pdev->dev, base_mem_res->start,
+ resource_size(base_mem_res), DRV_NAME)) {
dev_err(&pdev->dev, "resources busy\n");
return -EBUSY;
}
- base = (unsigned long)res->start;
+ ctl_mem_res = platform_get_resource(pdev, IORESOURCE_MEM, 1);
+ if (!ctl_mem_res)
+ return -ENODEV;
+
+ if (MACH_IS_ATARI) {
+ irq = IRQ_MFP_IDE;
+ } else {
+ irq_res = platform_get_resource(pdev, IORESOURCE_IRQ, 0);
+ if (irq_res && irq_res->start > 0)
+ irq = irq_res->start;
+ else
+ return -ENODEV;
+ }
- falconide_setup_ports(&hw, base);
+ falconide_setup_ports(&hw, base_mem_res->start, ctl_mem_res->start, irq);
host = ide_host_alloc(&falconide_port_info, hws, 1);
- if (host == NULL) {
- rc = -ENOMEM;
- goto err;
+ if (!host)
+ return -ENOMEM;
+
+ if (!MACH_IS_ATARI) {
+ host->get_lock = NULL;
+ host->release_lock = NULL;
}
- falconide_get_lock(NULL, NULL);
+ if (host->get_lock)
+ host->get_lock(NULL, NULL);
rc = ide_host_register(host, &falconide_port_info, hws);
- falconide_release_lock();
+ if (host->release_lock)
+ host->release_lock();
if (rc)
goto err_free;
@@ -168,8 +195,6 @@ static int __init falconide_init(struct platform_device *pdev)
return 0;
err_free:
ide_host_free(host);
-err:
- release_mem_region(res->start, resource_size(res));
return rc;
}
diff --git a/drivers/ide/q40ide.c b/drivers/ide/q40ide.c
deleted file mode 100644
index ecd0a69245f6..000000000000
--- a/drivers/ide/q40ide.c
+++ /dev/null
@@ -1,168 +0,0 @@
-/*
- * Q40 I/O port IDE Driver
- *
- * (c) Richard Zidlicky
- *
- * This file is subject to the terms and conditions of the GNU General Public
- * License. See the file COPYING in the main directory of this archive for
- * more details.
- *
- *
- */
-
-#include <linux/types.h>
-#include <linux/mm.h>
-#include <linux/interrupt.h>
-#include <linux/blkdev.h>
-#include <linux/ide.h>
-#include <linux/module.h>
-
-#include <asm/ide.h>
-
- /*
- * Bases of the IDE interfaces
- */
-
-#define Q40IDE_NUM_HWIFS 2
-
-#define PCIDE_BASE1 0x1f0
-#define PCIDE_BASE2 0x170
-#define PCIDE_BASE3 0x1e8
-#define PCIDE_BASE4 0x168
-#define PCIDE_BASE5 0x1e0
-#define PCIDE_BASE6 0x160
-
-static const unsigned long pcide_bases[Q40IDE_NUM_HWIFS] = {
- PCIDE_BASE1, PCIDE_BASE2, /* PCIDE_BASE3, PCIDE_BASE4 , PCIDE_BASE5,
- PCIDE_BASE6 */
-};
-
-static int q40ide_default_irq(unsigned long base)
-{
- switch (base) {
- case 0x1f0: return 14;
- case 0x170: return 15;
- case 0x1e8: return 11;
- default:
- return 0;
- }
-}
-
-
-/*
- * Addresses are pretranslated for Q40 ISA access.
- */
-static void q40_ide_setup_ports(struct ide_hw *hw, unsigned long base, int irq)
-{
- memset(hw, 0, sizeof(*hw));
- /* BIG FAT WARNING:
- assumption: only DATA port is ever used in 16 bit mode */
- hw->io_ports.data_addr = Q40_ISA_IO_W(base);
- hw->io_ports.error_addr = Q40_ISA_IO_B(base + 1);
- hw->io_ports.nsect_addr = Q40_ISA_IO_B(base + 2);
- hw->io_ports.lbal_addr = Q40_ISA_IO_B(base + 3);
- hw->io_ports.lbam_addr = Q40_ISA_IO_B(base + 4);
- hw->io_ports.lbah_addr = Q40_ISA_IO_B(base + 5);
- hw->io_ports.device_addr = Q40_ISA_IO_B(base + 6);
- hw->io_ports.status_addr = Q40_ISA_IO_B(base + 7);
- hw->io_ports.ctl_addr = Q40_ISA_IO_B(base + 0x206);
-
- hw->irq = irq;
-}
-
-static void q40ide_input_data(ide_drive_t *drive, struct ide_cmd *cmd,
- void *buf, unsigned int len)
-{
- unsigned long data_addr = drive->hwif->io_ports.data_addr;
-
- if (drive->media == ide_disk && cmd && (cmd->tf_flags & IDE_TFLAG_FS)) {
- __ide_mm_insw(data_addr, buf, (len + 1) / 2);
- return;
- }
-
- raw_insw_swapw((u16 *)data_addr, buf, (len + 1) / 2);
-}
-
-static void q40ide_output_data(ide_drive_t *drive, struct ide_cmd *cmd,
- void *buf, unsigned int len)
-{
- unsigned long data_addr = drive->hwif->io_ports.data_addr;
-
- if (drive->media == ide_disk && cmd && (cmd->tf_flags & IDE_TFLAG_FS)) {
- __ide_mm_outsw(data_addr, buf, (len + 1) / 2);
- return;
- }
-
- raw_outsw_swapw((u16 *)data_addr, buf, (len + 1) / 2);
-}
-
-/* Q40 has a byte-swapped IDE interface */
-static const struct ide_tp_ops q40ide_tp_ops = {
- .exec_command = ide_exec_command,
- .read_status = ide_read_status,
- .read_altstatus = ide_read_altstatus,
- .write_devctl = ide_write_devctl,
-
- .dev_select = ide_dev_select,
- .tf_load = ide_tf_load,
- .tf_read = ide_tf_read,
-
- .input_data = q40ide_input_data,
- .output_data = q40ide_output_data,
-};
-
-static const struct ide_port_info q40ide_port_info = {
- .tp_ops = &q40ide_tp_ops,
- .host_flags = IDE_HFLAG_MMIO | IDE_HFLAG_NO_DMA,
- .irq_flags = IRQF_SHARED,
- .chipset = ide_generic,
-};
-
-/*
- * the static array is needed to have the name reported in /proc/ioports,
- * hwif->name unfortunately isn't available yet
- */
-static const char *q40_ide_names[Q40IDE_NUM_HWIFS]={
- "ide0", "ide1"
-};
-
-/*
- * Probe for Q40 IDE interfaces
- */
-
-static int __init q40ide_init(void)
-{
- int i;
- struct ide_hw hw[Q40IDE_NUM_HWIFS], *hws[] = { NULL, NULL };
-
- if (!MACH_IS_Q40)
- return -ENODEV;
-
- printk(KERN_INFO "ide: Q40 IDE controller\n");
-
- for (i = 0; i < Q40IDE_NUM_HWIFS; i++) {
- const char *name = q40_ide_names[i];
-
- if (!request_region(pcide_bases[i], 8, name)) {
- printk("could not reserve ports %lx-%lx for %s\n",
- pcide_bases[i],pcide_bases[i]+8,name);
- continue;
- }
- if (!request_region(pcide_bases[i]+0x206, 1, name)) {
- printk("could not reserve port %lx for %s\n",
- pcide_bases[i]+0x206,name);
- release_region(pcide_bases[i], 8);
- continue;
- }
- q40_ide_setup_ports(&hw[i], pcide_bases[i],
- q40ide_default_irq(pcide_bases[i]));
-
- hws[i] = &hw[i];
- }
-
- return ide_host_add(&q40ide_port_info, hws, Q40IDE_NUM_HWIFS, NULL);
-}
-
-module_init(q40ide_init);
-
-MODULE_LICENSE("GPL");
--
2.26.3
