Re: [PATCH RFC 2/2] net/8390: apne.c - add 100 Mbit support to apne.c driver

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Hi Geert,

Am 07.06.2021 um 20:08 schrieb Geert Uytterhoeven:
Hi Michael,

On Sun, Jun 6, 2021 at 7:54 AM Michael Schmitz <schmitzmic@xxxxxxxxx> wrote:
Add Kconfig option, module parameter and PCMCIA reset code
required to support 100 Mbit PCMCIA ethernet cards on Amiga.

10 Mbit and 100 Mbit mode are supported by the same module.
A module parameter switches Amiga ISA IO accessors to word
access by changing isa_type at runtime. Additional code to
reset the PCMCIA hardware is also added to the driver probe.

Patch modified after patch "[PATCH RFC net-next] Amiga PCMCIA
100 MBit card support" submitted to netdev 2018/09/16 by Alex
Kazik <alex@xxxxxxxx>.

Signed-off-by: Michael Schmitz <schmitzmic@xxxxxxxxx>

Thanks for your patch!

--- a/drivers/net/ethernet/8390/Kconfig
+++ b/drivers/net/ethernet/8390/Kconfig
@@ -143,6 +143,19 @@ config APNE
          To compile this driver as a module, choose M here: the module
          will be called apne.

+if APNE

Please use "depends on APNE" instead of an if/endif block, as there's
only a single symbol to cover.

True - I had copied that straight from Alex' patch ..


+config APNE100MBIT
+       bool "PCMCIA NE2000 100MBit support"
+       default n
+       ---help---
+         This changes the driver to support 10/100Mbit cards (e.g. Netgear
+         FA411, CNet Singlepoint). 10 MBit cards and 100 MBit cards are
+         supported by the same driver.
+
+         To activate 100 Mbit support at runtime, use the apne100 module
+         parameter.

Trailing space.

And ---help--- did confuse kbuild, as I found out.

+endif
+
 config PCMCIA_PCNET
        tristate "NE2000 compatible PCMCIA support"
        depends on PCMCIA
diff --git a/drivers/net/ethernet/8390/apne.c b/drivers/net/ethernet/8390/apne.c
index fe6c834..9648e45 100644
--- a/drivers/net/ethernet/8390/apne.c
+++ b/drivers/net/ethernet/8390/apne.c
@@ -120,6 +120,10 @@ static u32 apne_msg_enable;
 module_param_named(msg_enable, apne_msg_enable, uint, 0444);
 MODULE_PARM_DESC(msg_enable, "Debug message level (see linux/netdevice.h for bitmap)");

+static u32 apne_100_mbit;
+module_param_named(apne_100_mbit, uint, 0);
+MODULE_PARM_DESC(apne_100_mbit, "Enable 100 Mbit support");

Shouldn't this depend on CONFIG_APNE100MBIT, too?
Perhaps we shouldn't bother with the config symbol, and include this
unconditionally?

At least the parameter should not hurt - this is entirely untested so I'd hate to break APNE by including the io_mm.h changes unconditionally.

+
 struct net_device * __init apne_probe(int unit)
 {
        struct net_device *dev;
@@ -139,6 +143,9 @@ struct net_device * __init apne_probe(int unit)
        if ( !(AMIGAHW_PRESENT(PCMCIA)) )
                return ERR_PTR(-ENODEV);

+        if (apne_100_mbit)
+                isa_type = ISA_TYPE_AG100;

Likewise.

And that one breaks if 16 bit support isn't always enabled. I'll conditionalize it.

Can we enable this automatically when needed, based on the chip
detected?

I wondered about that - we'd have to poke the chip with 16 bit IO if 8 bit IO fails, no idea what side effects that would have.

Maybe retrying the card reset in apne_probe1 again after changing isa_type would work, but someone would have to try that and report back.

+ spaces instead of TABs (scripts/checkpatch.pl is your friend).

Thanks, I'll fix that. Got sloppy with checkpatch, sorry.


+
        pr_info("Looking for PCMCIA ethernet card : ");

        /* check if a card is inserted */
@@ -590,6 +597,16 @@ static int init_pcmcia(void)
 #endif
        u_long offset;

+#ifdef CONFIG_APNE100MBIT
+       /* reset card (idea taken from CardReset by Artur Pogoda) */
+       {
+               u_char  tmp = gayle.intreq;
+
+               gayle.intreq = 0xff;    mdelay(1);
+               gayle.intreq = tmp;     mdelay(300);
+       }

Is this safe for all cards?

I _think_ so, but this really is a question for Alex and others involved in developing the original patch. (The original patch had that conditionalized as well so I might be wrong ...)

I'll send v2 once I've fixed these all up...

Cheers,

	Michael


+#endif
+
        pcmcia_reset();
        pcmcia_program_voltage(PCMCIA_0V);
        pcmcia_access_speed(PCMCIA_SPEED_250NS);

Gr{oetje,eeting}s,

                        Geert




[Index of Archives]     [Linux Filesystems]     [Linux SCSI]     [Linux RAID]     [Git]     [Kernel Newbies]     [Linux Newbie]     [Security]     [Netfilter]     [Bugtraq]     [Yosemite News]     [MIPS Linux]     [ARM Linux]     [Linux Security]     [Samba]     [Device Mapper]

  Powered by Linux