Fixes the following W=1 kernel build warning(s): drivers/ata/sata_mv.c:1162: warning: Function parameter or member 'ap' not described in 'mv_start_edma' drivers/ata/sata_mv.c:1162: warning: Function parameter or member 'port_mmio' not described in 'mv_start_edma' drivers/ata/sata_mv.c:1162: warning: Function parameter or member 'protocol' not described in 'mv_start_edma' drivers/ata/sata_mv.c:1162: warning: Excess function parameter 'base' description in 'mv_start_edma' drivers/ata/sata_mv.c:1535: warning: Function parameter or member 'enable_bmdma' not described in 'mv_bmdma_enable_iie' drivers/ata/sata_mv.c:1535: warning: expecting prototype for mv_bmdma_enable(). Prototype was for mv_bmdma_enable_iie() instead drivers/ata/sata_mv.c:1930: warning: Function parameter or member 'ap' not described in 'mv_bmdma_stop_ap' drivers/ata/sata_mv.c:1930: warning: expecting prototype for mv_bmdma_stop(). Prototype was for mv_bmdma_stop_ap() instead drivers/ata/sata_mv.c:2228: warning: Function parameter or member 'ap' not described in 'mv_send_fis' drivers/ata/sata_mv.c:3263: warning: Function parameter or member 'hpriv' not described in 'mv6_reset_hc' drivers/ata/sata_mv.c:3263: warning: Function parameter or member 'n_hc' not described in 'mv6_reset_hc' drivers/ata/sata_mv.c:3541: warning: Function parameter or member 'hpriv' not described in 'soc_is_65n' drivers/ata/sata_mv.c:3541: warning: expecting prototype for soc_is_65(). Prototype was for soc_is_65n() instead Cc: Jens Axboe <axboe@xxxxxxxxx> Cc: Mark Lord <mlord@xxxxxxxxx> Cc: ALWAYS copy <linux-ide@xxxxxxxxxxxxxxx> Cc: linux-ide@xxxxxxxxxxxxxxx Signed-off-by: Lee Jones <lee.jones@xxxxxxxxxx> --- drivers/ata/sata_mv.c | 12 ++++++------ 1 file changed, 6 insertions(+), 6 deletions(-) diff --git a/drivers/ata/sata_mv.c b/drivers/ata/sata_mv.c index 664ef658a955f..eafca46d8feb4 100644 --- a/drivers/ata/sata_mv.c +++ b/drivers/ata/sata_mv.c @@ -1146,9 +1146,8 @@ static void mv_set_irq_coalescing(struct ata_host *host, spin_unlock_irqrestore(&host->lock, flags); } -/** +/* * mv_start_edma - Enable eDMA engine - * @base: port base address * @pp: port private data * * Verify the local cache of the eDMA state is accurate with a @@ -1519,7 +1518,7 @@ static void mv_60x1_errata_sata25(struct ata_port *ap, int want_ncq) writel(new, hpriv->base + GPIO_PORT_CTL); } -/** +/* * mv_bmdma_enable - set a magic bit on GEN_IIE to allow bmdma * @ap: Port being initialized * @@ -1919,7 +1918,7 @@ static void mv_bmdma_start(struct ata_queued_cmd *qc) /** * mv_bmdma_stop - Stop BMDMA transfer - * @qc: queued command to stop DMA on. + * @ap: port to stop * * Clears the ATA_DMA_START flag in the bmdma control register * @@ -2221,6 +2220,7 @@ static u8 mv_sff_check_status(struct ata_port *ap) /** * mv_send_fis - Send a FIS, using the "Vendor-Unique FIS" register + * @ap: ATA port to send a FIS * @fis: fis to be sent * @nwords: number of 32-bit words in the fis */ @@ -3249,7 +3249,7 @@ static void mv6_reset_flash(struct mv_host_priv *hpriv, void __iomem *mmio) writel(tmp, mmio + GPIO_PORT_CTL); } -/** +/* * mv6_reset_hc - Perform the 6xxx global soft reset * @mmio: base address of the HBA * @@ -3530,7 +3530,7 @@ static void mv_soc_65n_phy_errata(struct mv_host_priv *hpriv, writel(reg, port_mmio + PHY_MODE9_GEN1); } -/** +/* * soc_is_65 - check if the soc is 65 nano device * * Detect the type of the SoC, this is done by reading the PHYCFG_OFS -- 2.25.1
