Hi,
On Mon, Jan 14, 2019 at 02:16:42PM +0100, Bartlomiej Zolnierkiewicz wrote:
> On 01/12/2019 04:26 PM, Aaro Koskinen wrote:
> > Hi,
> >
> > On Sun, Jan 06, 2019 at 02:46:07PM +0200, Aaro Koskinen wrote:
> >> Commit 7ff7a5b1bfff ("MIPS: lemote2f_defconfig: Convert to use libata
> >> PATA drivers") switched from IDE to libata PATA on Loongson 2F, but
> >> neither PATA_AMD or PATA_CS5536 work well on this platform compared
> >> to the AMD74XX IDE driver.
>
> Sorry about that.
>
> >> During the ATA init/probe there is interrupt storm from irq 14, and
> >> majority of system boots end up with "nobody cared... IRQ disabled".
> >> So the result is a very slow disk access.
> >>
> >> It seems that the interrupt gets crazy after the port freeze done early
> >> during the init, and for whatever reason it cannot be cleared.
> >>
> >> With the below workaround I was able to boot the system normally. I
> >> guess that rather than going back to old IDE driver, we should just try
> >> to make pata_cs5536 work (and forget PATA AMD on this board)...?
> >
> > Hmm, even with this hack I get ~500 spurious IRQs during the boot.
> >
> > Also compared to old IDE, there's 33 vs 100 speed difference:
> >
> > [ 3.324000] ata1: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0x4ce0 irq 14
> > [ 3.584000] ata1.00: ATA-8: WDC WD1600BEVS-00VAT0, 11.01A11, max UDMA/133
> > [ 3.588000] ata1.00: 312581808 sectors, multi 16: LBA48
> > [ 3.592000] ata1.00: limited to UDMA/33 due to 40-wire cable
> >
> > [ 4.540000] Probing IDE interface ide0...
> > [ 4.992000] hda: WDC WD1600BEVS-00VAT0, ATA DISK drive
> > [ 5.716000] hda: host max PIO5 wanted PIO255(auto-tune) selected PIO4
> > [ 5.716000] hda: UDMA/100 mode selected
>
> Can you try booting with "libata.force=1:80c" (and if that doesn't work with
> "libata.force=1:short40c")
(Sorry for delay, this machine is in use so I couldn't reboot it randomly...)
OK, the speed issue can be fixed with command line. So "libata.force=1:80c"
works with cs5536 libata driver.
> and also provide full dmesg-s for working (ide) and not working
> (libata) kernels.
Logs are below:
1) working IDE (no spurious IRQs)
2) working PATA AMD (around ~90k spurious IRQs, so it's just a matter of luck)
3) failing PATA AMD (100k spurious IRQs reached)
4) working PATA CS5536 (same as with PATA AMD)
5) failing PATA CS5536 (same as with PATA AMD)
-----
1) Working IDE with amd74xx.
[ 0.000000] Linux version 4.20.0-lemote-los_919f1 (aaro@amd-fx-6350) (gcc version 7.4.0 (GCC)) #1 Sat Jan 26 17:11:52 EET 2019
[ 0.000000] memsize=256, highmemsize=256
[ 0.000000] CpuClock = 797780000
[ 0.000000] printk: bootconsole [early0] enabled
[ 0.000000] CPU0 revision is: 00006303 (ICT Loongson-2)
[ 0.000000] FPU revision is: 00000501
[ 0.000000] Checking for the multiply/shift bug... no.
[ 0.000000] Checking for the daddiu bug... no.
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 0000000010000000 @ 0000000000000000 (usable)
[ 0.000000] memory: 0000000030000000 @ 0000000010000000 (reserved)
[ 0.000000] memory: 0000000010000000 @ 0000000090000000 (usable)
[ 0.000000] memory: 0000000010000000 @ 0000000080000000 (reserved)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Primary instruction cache 64kB, VIPT, direct mapped, linesize 32 bytes.
[ 0.000000] Primary data cache 64kB, 4-way, VIPT, no aliases, linesize 32 bytes
[ 0.000000] Unified secondary cache 512kB 4-way, linesize 32 bytes.
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x0000000000000000-0x000000009fffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000000000-0x000000003fffffff]
[ 0.000000] node 0: [mem 0x0000000080000000-0x000000009fffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x000000009fffffff]
[ 0.000000] On node 0 totalpages: 98304
[ 0.000000] Normal zone: 336 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 98304 pages, LIFO batch:15
[ 0.000000] random: get_random_bytes called from start_kernel+0xa0/0x580 with crng_init=0
[ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[ 0.000000] pcpu-alloc: [0] 0
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 97968
[ 0.000000] Kernel command line: console=tty console=ttyS0,115200
[ 0.000000] Dentry cache hash table entries: 262144 (order: 7, 2097152 bytes)
[ 0.000000] Inode-cache hash table entries: 131072 (order: 6, 1048576 bytes)
[ 0.000000] Memory: 491728K/1572864K available (4731K kernel code, 475K rwdata, 856K rodata, 2048K init, 16616K bss, 1081136K reserved, 0K cma-reserved)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS: 128
[ 0.000000] Console: colour dummy device 80x25
[ 0.000000] printk: console [tty0] enabled
[ 0.000000] sched_clock: 64 bits at 250 Hz, resolution 4000000ns, wraps every 9007199254000000ns
[ 0.004000] Calibrating delay loop... 528.38 BogoMIPS (lpj=1056768)
[ 0.040000] pid_max: default: 32768 minimum: 301
[ 0.044000] Mount-cache hash table entries: 4096 (order: 1, 32768 bytes)
[ 0.048000] Mountpoint-cache hash table entries: 4096 (order: 1, 32768 bytes)
[ 0.052000] Checking for the daddi bug... no.
[ 0.060000] devtmpfs: initialized
[ 0.064000] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
[ 0.068000] futex hash table entries: 256 (order: -2, 6144 bytes)
[ 0.072000] NET: Registered protocol family 16
[ 0.076000] clocksource: mfgpt: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 133486551712 ns
[ 0.120000] SCSI subsystem initialized
[ 0.124000] usbcore: registered new interface driver usbfs
[ 0.128000] usbcore: registered new interface driver hub
[ 0.132000] usbcore: registered new device driver usb
[ 0.140000] PCI host bridge to bus 0000:00
[ 0.144000] pci_bus 0000:00: root bus resource [mem 0x40000000-0x7fffffff]
[ 0.148000] pci_bus 0000:00: root bus resource [io 0x4000-0xffff]
[ 0.152000] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0]
[ 0.156000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[ 0.160000] pci 0000:00:06.0: [10ec:8169] type 00 class 0x020000
[ 0.160000] pci 0000:00:06.0: reg 0x10: [io 0xb100-0xb1ff]
[ 0.160000] pci 0000:00:06.0: reg 0x14: [mem 0x04075000-0x040750ff]
[ 0.160000] pci 0000:00:06.0: reg 0x30: [mem 0x04040000-0x0405ffff pref]
[ 0.160000] pci 0000:00:06.0: supports D1 D2
[ 0.160000] pci 0000:00:06.0: PME# supported from D1 D2 D3hot
[ 0.160000] pci 0000:00:08.0: [1039:0325] type 00 class 0x030000
[ 0.160000] pci 0000:00:08.0: reg 0x10: [mem 0x40000000-0x4fffffff pref]
[ 0.160000] pci 0000:00:08.0: reg 0x14: [mem 0x04000000-0x0403ffff]
[ 0.160000] pci 0000:00:08.0: reg 0x18: [io 0xb300-0xb37f]
[ 0.160000] pci 0000:00:08.0: reg 0x30: [mem 0x04060000-0x0406ffff pref]
[ 0.160000] pci 0000:00:08.0: supports D1 D2
[ 0.160000] pci 0000:00:0e.0: [1022:2090] type 00 class 0x060100
[ 0.160000] pci 0000:00:0e.0: reg 0x10: [io 0xb410-0xb417]
[ 0.160000] pci 0000:00:0e.0: reg 0x14: [io 0xb000-0xb0ff]
[ 0.160000] pci 0000:00:0e.0: reg 0x18: [io 0xb380-0xb3bf]
[ 0.160000] pci 0000:00:0e.0: reg 0x20: [io 0xb280-0xb2ff]
[ 0.160000] pci 0000:00:0e.0: reg 0x24: [io 0xb3c0-0xb3df]
[ 0.160000] pci 0000:00:0e.2: [1022:209a] type 00 class 0x010180
[ 0.160000] pci 0000:00:0e.2: reg 0x20: [io 0xb400-0xb40f]
[ 0.160000] pci 0000:00:0e.2: legacy IDE quirk: reg 0x10: [io 0x01f0-0x01f7]
[ 0.164000] pci 0000:00:0e.2: legacy IDE quirk: reg 0x14: [io 0x03f6]
[ 0.168000] pci 0000:00:0e.2: legacy IDE quirk: reg 0x18: [io 0x0170-0x0177]
[ 0.172000] pci 0000:00:0e.2: legacy IDE quirk: reg 0x1c: [io 0x0376]
[ 0.176000] pci 0000:00:0e.3: [1022:2093] type 00 class 0x040100
[ 0.176000] pci 0000:00:0e.3: reg 0x10: [io 0xb200-0xb27f]
[ 0.176000] pci 0000:00:0e.4: [1022:2094] type 00 class 0x0c0310
[ 0.176000] pci 0000:00:0e.4: reg 0x10: [mem 0x04074000-0x04074fff]
[ 0.180000] pci 0000:00:0e.5: [1022:2095] type 00 class 0x0c0320
[ 0.180000] pci 0000:00:0e.5: reg 0x10: [mem 0x04073000-0x04073fff]
[ 0.180000] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 00
[ 0.180000] pci 0000:00:08.0: BAR 0: assigned [mem 0x40000000-0x4fffffff pref]
[ 0.184000] pci 0000:00:08.0: BAR 1: assigned [mem 0x50000000-0x5003ffff]
[ 0.188000] pci 0000:00:06.0: BAR 6: assigned [mem 0x50040000-0x5005ffff pref]
[ 0.192000] pci 0000:00:08.0: BAR 6: assigned [mem 0x50060000-0x5006ffff pref]
[ 0.196000] pci 0000:00:0e.4: BAR 0: assigned [mem 0x50070000-0x50070fff]
[ 0.200000] pci 0000:00:0e.5: BAR 0: assigned [mem 0x50071000-0x50071fff]
[ 0.204000] pci 0000:00:06.0: BAR 0: assigned [io 0x4000-0x40ff]
[ 0.208000] pci 0000:00:06.0: BAR 1: assigned [mem 0x50072000-0x500720ff]
[ 0.212000] pci 0000:00:0e.0: BAR 1: assigned [io 0x4400-0x44ff]
[ 0.216000] pci 0000:00:08.0: BAR 2: assigned [io 0x4800-0x487f]
[ 0.220000] pci 0000:00:0e.0: BAR 4: assigned [io 0x4880-0x48ff]
[ 0.224000] pci 0000:00:0e.3: BAR 0: assigned [io 0x4c00-0x4c7f]
[ 0.228000] pci 0000:00:0e.0: BAR 2: assigned [io 0x4c80-0x4cbf]
[ 0.232000] pci 0000:00:0e.0: BAR 5: assigned [io 0x4cc0-0x4cdf]
[ 0.236000] pci 0000:00:0e.2: BAR 4: assigned [io 0x4ce0-0x4cef]
[ 0.240000] pci 0000:00:0e.0: BAR 0: assigned [io 0x4cf0-0x4cf7]
[ 0.248000] clocksource: Switched to clocksource mfgpt
[ 0.276000] NET: Registered protocol family 2
[ 0.280000] tcp_listen_portaddr_hash hash table entries: 1024 (order: 0, 16384 bytes)
[ 0.284000] TCP established hash table entries: 16384 (order: 3, 131072 bytes)
[ 0.288000] TCP bind hash table entries: 16384 (order: 3, 131072 bytes)
[ 0.292000] TCP: Hash tables configured (established 16384 bind 16384)
[ 0.296000] UDP hash table entries: 1024 (order: 1, 32768 bytes)
[ 0.300000] UDP-Lite hash table entries: 1024 (order: 1, 32768 bytes)
[ 0.304000] NET: Registered protocol family 1
[ 0.308000] pci 0000:00:0e.4: enabling device (0000 -> 0002)
[ 0.312000] PCI: CLS 32 bytes, default 32
[ 0.892000] random: fast init done
[ 1.740000] workingset: timestamp_bits=62 max_order=15 bucket_order=0
[ 2.172000] NET: Registered protocol family 38
[ 2.176000] io scheduler noop registered
[ 2.180000] io scheduler cfq registered (default)
[ 2.184000] slot: 8, pin: 1, irq: 38
[ 2.188000] sisfb 0000:00:08.0: Invalid PCI ROM header signature: expecting 0xaa55, got 0x3030
[ 2.192000] sisfb: Video ROM not found
[ 2.196000] sisfb: Video RAM at 0x40000000, mapped to 0x9000000040000000, size 32768k
[ 2.200000] sisfb: MMIO at 0x50000000, mapped to 0x9000000050000000, size 256k
[ 2.204000] sisfb: Memory heap starting at 32160K, size 32K
[ 3.492000] sisfb: Detected SiS301C video bridge
[ 3.576000] sisfb: Detected 1280x1024 flat panel
[ 3.656000] sisfb: CRT2 DDC supported
[ 3.660000] sisfb: CRT2 DDC level: 2
[ 3.868000] sisfb: Monitor range H 30-81KHz, V 56-76Hz, Max. dotclock 140MHz
[ 3.872000] sisfb: Default mode is 1280x1024x8 (60Hz)
[ 3.876000] sisfb: Initial vbflags 0x10000022
[ 3.948000] Console: switching to colour frame buffer device 160x64
[ 4.004000] sisfb: 2D acceleration is enabled, y-panning enabled (auto-max)
[ 4.008000] fb0: SiS 315PRO frame buffer device version 1.8.9
[ 4.012000] sisfb: Copyright (C) 2001-2005 Thomas Winischhofer
[ 4.068000] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[ 4.212000] printk: console [ttyS0] disabled
[ 4.220000] serial8250.0: ttyS0 at I/O 0x2f8 (irq = 3, base_baud = 115200) is a 16550A
[ 4.224000] printk: console [ttyS0] enabled
[ 4.228000] printk: bootconsole [early0] disabled
[ 4.848000] brd: module loaded
[ 5.000000] loop: module loaded
[ 5.000000] Uniform Multi-Platform E-IDE driver
[ 5.004000] amd74xx 0000:00:0e.2: UDMA100 controller
[ 5.008000] amd74xx 0000:00:0e.2: IDE controller (0x1022:0x209a rev 0x01)
[ 5.012000] amd74xx 0000:00:0e.2: IDE port disabled
[ 5.016000] amd74xx 0000:00:0e.2: not 100% native mode: will probe irqs later
[ 5.020000] ide0: BM-DMA at 0x4ce0-0x4ce7
[ 5.024000] Probing IDE interface ide0...
[ 5.412000] hda: WDC WD1600BEVS-00VAT0, ATA DISK drive
[ 6.136000] hda: host max PIO5 wanted PIO255(auto-tune) selected PIO4
[ 6.136000] hda: UDMA/100 mode selected
[ 6.140000] ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
[ 6.144000] ide-gd driver 1.18
[ 6.148000] hda: max request size: 1024KiB
[ 6.228000] hda: 312581808 sectors (160041 MB) w/8192KiB Cache, CHS=19457/255/63
[ 6.232000] hda: cache flushes supported
[ 6.252000] hda: hda1
[ 6.256000] slot: 6, pin: 1, irq: 36
[ 6.260000] r8169 0000:00:06.0: not PCI Express
[ 6.264000] libphy: r8169: probed
[ 6.268000] r8169 0000:00:06.0 eth0: RTL8169sc/8110sc, 00:23:9e:00:0f:54, XID 98000000, IRQ 36
[ 6.272000] r8169 0000:00:06.0 eth0: jumbo features [frames: 7152 bytes, tx checksumming: ok]
[ 6.276000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 6.280000] ehci-pci: EHCI PCI platform driver
[ 6.284000] ehci-pci 0000:00:0e.5: EHCI Host Controller
[ 6.288000] ehci-pci 0000:00:0e.5: new USB bus registered, assigned bus number 1
[ 6.292000] ehci-pci 0000:00:0e.5: irq 11, io mem 0x50071000
[ 6.432000] ehci-pci 0000:00:0e.5: USB 0.0 started, EHCI 1.00
[ 6.436000] hub 1-0:1.0: USB hub found
[ 6.448000] hub 1-0:1.0: 4 ports detected
[ 6.456000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 6.460000] ohci-pci: OHCI PCI platform driver
[ 6.464000] ohci-pci 0000:00:0e.4: OHCI PCI host controller
[ 6.468000] ohci-pci 0000:00:0e.4: new USB bus registered, assigned bus number 2
[ 6.472000] ohci-pci 0000:00:0e.4: irq 11, io mem 0x50070000
[ 6.568000] hub 2-0:1.0: USB hub found
[ 6.580000] hub 2-0:1.0: 4 ports detected
[ 6.588000] usbcore: registered new interface driver usb-storage
[ 6.592000] loongson2_cpufreq: Loongson-2F CPU frequency driver
[ 6.596000] usbcore: registered new interface driver usbhid
[ 6.600000] usbhid: USB HID core driver
[ 6.608000] NET: Registered protocol family 17
[ 6.680000] Freeing unused kernel memory: 2048K
[ 6.684000] This architecture does not have kernel memory protection.
[ 6.688000] Run /init as init process
[ 10.872000] EXT4-fs (hda1): mounting ext3 file system using the ext4 subsystem
[ 10.940000] EXT4-fs (hda1): mounted filesystem with ordered data mode. Opts: (null)
[ 11.984000] random: crng init done
[ 13.752000] Adding 524256k swap on /SWAP. Priority:-2 extents:13 across:145760016k
[ 13.868000] RTL8211B Gigabit Ethernet r8169-30:00: attached PHY driver [RTL8211B Gigabit Ethernet] (mii_bus:phy_addr=r8169-30:00, irq=IGNORE)
[ 16.604000] r8169 0000:00:06.0 eth0: Link is Up - 1Gbps/Full - flow control rx/tx
-----
2) Working PATA AMD.
[ 0.000000] Linux version 4.20.0-lemote-los_42599 (aaro@amd-fx-6350) (gcc version 7.4.0 (GCC)) #1 Sat Jan 26 19:29:46 EET 2019
[ 0.000000] memsize=256, highmemsize=256
[ 0.000000] CpuClock = 797800000
[ 0.000000] printk: bootconsole [early0] enabled
[ 0.000000] CPU0 revision is: 00006303 (ICT Loongson-2)
[ 0.000000] FPU revision is: 00000501
[ 0.000000] Checking for the multiply/shift bug... no.
[ 0.000000] Checking for the daddiu bug... no.
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 0000000010000000 @ 0000000000000000 (usable)
[ 0.000000] memory: 0000000030000000 @ 0000000010000000 (reserved)
[ 0.000000] memory: 0000000010000000 @ 0000000090000000 (usable)
[ 0.000000] memory: 0000000010000000 @ 0000000080000000 (reserved)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Primary instruction cache 64kB, VIPT, direct mapped, linesize 32 bytes.
[ 0.000000] Primary data cache 64kB, 4-way, VIPT, no aliases, linesize 32 bytes
[ 0.000000] Unified secondary cache 512kB 4-way, linesize 32 bytes.
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x0000000000000000-0x000000009fffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000000000-0x000000003fffffff]
[ 0.000000] node 0: [mem 0x0000000080000000-0x000000009fffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x000000009fffffff]
[ 0.000000] On node 0 totalpages: 98304
[ 0.000000] Normal zone: 336 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 98304 pages, LIFO batch:15
[ 0.000000] random: get_random_bytes called from start_kernel+0xa0/0x580 with crng_init=0
[ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[ 0.000000] pcpu-alloc: [0] 0
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 97968
[ 0.000000] Kernel command line: console=tty console=ttyS0,115200
[ 0.000000] Dentry cache hash table entries: 262144 (order: 7, 2097152 bytes)
[ 0.000000] Inode-cache hash table entries: 131072 (order: 6, 1048576 bytes)
[ 0.000000] Memory: 491728K/1572864K available (4784K kernel code, 465K rwdata, 876K rodata, 2048K init, 16620K bss, 1081136K reserved, 0K cma-reserved)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS: 128
[ 0.000000] Console: colour dummy device 80x25
[ 0.000000] printk: console [tty0] enabled
[ 0.000000] sched_clock: 64 bits at 250 Hz, resolution 4000000ns, wraps every 9007199254000000ns
[ 0.004000] Calibrating delay loop... 528.38 BogoMIPS (lpj=1056768)
[ 0.040000] pid_max: default: 32768 minimum: 301
[ 0.044000] Mount-cache hash table entries: 4096 (order: 1, 32768 bytes)
[ 0.048000] Mountpoint-cache hash table entries: 4096 (order: 1, 32768 bytes)
[ 0.052000] Checking for the daddi bug... no.
[ 0.060000] devtmpfs: initialized
[ 0.064000] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
[ 0.068000] futex hash table entries: 256 (order: -2, 6144 bytes)
[ 0.072000] NET: Registered protocol family 16
[ 0.076000] clocksource: mfgpt: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 133486551712 ns
[ 0.124000] SCSI subsystem initialized
[ 0.128000] libata version 3.00 loaded.
[ 0.128000] usbcore: registered new interface driver usbfs
[ 0.132000] usbcore: registered new interface driver hub
[ 0.136000] usbcore: registered new device driver usb
[ 0.144000] PCI host bridge to bus 0000:00
[ 0.148000] pci_bus 0000:00: root bus resource [mem 0x40000000-0x7fffffff]
[ 0.152000] pci_bus 0000:00: root bus resource [io 0x4000-0xffff]
[ 0.156000] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0]
[ 0.160000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[ 0.164000] pci 0000:00:06.0: [10ec:8169] type 00 class 0x020000
[ 0.164000] pci 0000:00:06.0: reg 0x10: [io 0xb100-0xb1ff]
[ 0.164000] pci 0000:00:06.0: reg 0x14: [mem 0x04075000-0x040750ff]
[ 0.164000] pci 0000:00:06.0: reg 0x30: [mem 0x04040000-0x0405ffff pref]
[ 0.164000] pci 0000:00:06.0: supports D1 D2
[ 0.164000] pci 0000:00:06.0: PME# supported from D1 D2 D3hot
[ 0.164000] pci 0000:00:08.0: [1039:0325] type 00 class 0x030000
[ 0.164000] pci 0000:00:08.0: reg 0x10: [mem 0x40000000-0x4fffffff pref]
[ 0.164000] pci 0000:00:08.0: reg 0x14: [mem 0x04000000-0x0403ffff]
[ 0.164000] pci 0000:00:08.0: reg 0x18: [io 0xb300-0xb37f]
[ 0.164000] pci 0000:00:08.0: reg 0x30: [mem 0x04060000-0x0406ffff pref]
[ 0.164000] pci 0000:00:08.0: supports D1 D2
[ 0.164000] pci 0000:00:0e.0: [1022:2090] type 00 class 0x060100
[ 0.164000] pci 0000:00:0e.0: reg 0x10: [io 0xb410-0xb417]
[ 0.164000] pci 0000:00:0e.0: reg 0x14: [io 0xb000-0xb0ff]
[ 0.164000] pci 0000:00:0e.0: reg 0x18: [io 0xb380-0xb3bf]
[ 0.164000] pci 0000:00:0e.0: reg 0x20: [io 0xb280-0xb2ff]
[ 0.164000] pci 0000:00:0e.0: reg 0x24: [io 0xb3c0-0xb3df]
[ 0.164000] pci 0000:00:0e.2: [1022:209a] type 00 class 0x010180
[ 0.164000] pci 0000:00:0e.2: reg 0x20: [io 0xb400-0xb40f]
[ 0.164000] pci 0000:00:0e.2: legacy IDE quirk: reg 0x10: [io 0x01f0-0x01f7]
[ 0.168000] pci 0000:00:0e.2: legacy IDE quirk: reg 0x14: [io 0x03f6]
[ 0.172000] pci 0000:00:0e.2: legacy IDE quirk: reg 0x18: [io 0x0170-0x0177]
[ 0.176000] pci 0000:00:0e.2: legacy IDE quirk: reg 0x1c: [io 0x0376]
[ 0.180000] pci 0000:00:0e.3: [1022:2093] type 00 class 0x040100
[ 0.180000] pci 0000:00:0e.3: reg 0x10: [io 0xb200-0xb27f]
[ 0.180000] pci 0000:00:0e.4: [1022:2094] type 00 class 0x0c0310
[ 0.180000] pci 0000:00:0e.4: reg 0x10: [mem 0x04074000-0x04074fff]
[ 0.180000] pci 0000:00:0e.5: [1022:2095] type 00 class 0x0c0320
[ 0.180000] pci 0000:00:0e.5: reg 0x10: [mem 0x04073000-0x04073fff]
[ 0.180000] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 00
[ 0.180000] pci 0000:00:08.0: BAR 0: assigned [mem 0x40000000-0x4fffffff pref]
[ 0.184000] pci 0000:00:08.0: BAR 1: assigned [mem 0x50000000-0x5003ffff]
[ 0.188000] pci 0000:00:06.0: BAR 6: assigned [mem 0x50040000-0x5005ffff pref]
[ 0.192000] pci 0000:00:08.0: BAR 6: assigned [mem 0x50060000-0x5006ffff pref]
[ 0.196000] pci 0000:00:0e.4: BAR 0: assigned [mem 0x50070000-0x50070fff]
[ 0.200000] pci 0000:00:0e.5: BAR 0: assigned [mem 0x50071000-0x50071fff]
[ 0.204000] pci 0000:00:06.0: BAR 0: assigned [io 0x4000-0x40ff]
[ 0.208000] pci 0000:00:06.0: BAR 1: assigned [mem 0x50072000-0x500720ff]
[ 0.212000] pci 0000:00:0e.0: BAR 1: assigned [io 0x4400-0x44ff]
[ 0.216000] pci 0000:00:08.0: BAR 2: assigned [io 0x4800-0x487f]
[ 0.220000] pci 0000:00:0e.0: BAR 4: assigned [io 0x4880-0x48ff]
[ 0.224000] pci 0000:00:0e.3: BAR 0: assigned [io 0x4c00-0x4c7f]
[ 0.228000] pci 0000:00:0e.0: BAR 2: assigned [io 0x4c80-0x4cbf]
[ 0.232000] pci 0000:00:0e.0: BAR 5: assigned [io 0x4cc0-0x4cdf]
[ 0.236000] pci 0000:00:0e.2: BAR 4: assigned [io 0x4ce0-0x4cef]
[ 0.240000] pci 0000:00:0e.0: BAR 0: assigned [io 0x4cf0-0x4cf7]
[ 0.244000] clocksource: Switched to clocksource mfgpt
[ 0.268000] NET: Registered protocol family 2
[ 0.276000] tcp_listen_portaddr_hash hash table entries: 1024 (order: 0, 16384 bytes)
[ 0.284000] TCP established hash table entries: 16384 (order: 3, 131072 bytes)
[ 0.288000] TCP bind hash table entries: 16384 (order: 3, 131072 bytes)
[ 0.292000] TCP: Hash tables configured (established 16384 bind 16384)
[ 0.296000] UDP hash table entries: 1024 (order: 1, 32768 bytes)
[ 0.300000] UDP-Lite hash table entries: 1024 (order: 1, 32768 bytes)
[ 0.304000] NET: Registered protocol family 1
[ 0.308000] pci 0000:00:0e.4: enabling device (0000 -> 0002)
[ 0.312000] PCI: CLS 32 bytes, default 32
[ 0.892000] random: fast init done
[ 1.736000] workingset: timestamp_bits=62 max_order=15 bucket_order=0
[ 2.164000] NET: Registered protocol family 38
[ 2.168000] io scheduler noop registered
[ 2.172000] io scheduler cfq registered (default)
[ 2.176000] slot: 8, pin: 1, irq: 38
[ 2.180000] sisfb 0000:00:08.0: Invalid PCI ROM header signature: expecting 0xaa55, got 0x3030
[ 2.184000] sisfb: Video ROM not found
[ 2.188000] sisfb: Video RAM at 0x40000000, mapped to 0x9000000040000000, size 32768k
[ 2.192000] sisfb: MMIO at 0x50000000, mapped to 0x9000000050000000, size 256k
[ 2.196000] sisfb: Memory heap starting at 32160K, size 32K
[ 3.488000] sisfb: Detected SiS301C video bridge
[ 3.572000] sisfb: Detected 1280x1024 flat panel
[ 3.652000] sisfb: CRT1 DDC probing failed
[ 3.656000] sisfb: Default mode is 1280x1024x8 (60Hz)
[ 3.660000] sisfb: Initial vbflags 0x10000022
[ 3.732000] Console: switching to colour frame buffer device 160x64
[ 3.788000] sisfb: 2D acceleration is enabled, y-panning enabled (auto-max)
[ 3.792000] fb0: SiS 315PRO frame buffer device version 1.8.9
[ 3.796000] sisfb: Copyright (C) 2001-2005 Thomas Winischhofer
[ 3.808000] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[ 3.956000] printk: console [ttyS0] disabled
[ 3.964000] serial8250.0: ttyS0 at I/O 0x2f8 (irq = 3, base_baud = 115200) is a 16550A
[ 3.968000] printk: console [ttyS0] enabled
[ 3.972000] printk: bootconsole [early0] disabled
[ 4.692000] brd: module loaded
[ 4.792000] loop: module loaded
[ 4.796000] pata_amd 0000:00:0e.2: version 0.4.1
[ 4.912000] random: crng init done
[ 5.148000] scsi host0: pata_amd
[ 5.384000] scsi host1: pata_amd
[ 5.392000] ata1: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0x4ce0 irq 14
[ 5.396000] ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0x4ce8 irq 15
[ 5.404000] slot: 6, pin: 1, irq: 36
[ 5.408000] r8169 0000:00:06.0: not PCI Express
[ 5.416000] libphy: r8169: probed
[ 5.428000] r8169 0000:00:06.0 eth0: RTL8169sc/8110sc, 00:23:9e:00:0f:54, XID 98000000, IRQ 36
[ 5.432000] r8169 0000:00:06.0 eth0: jumbo features [frames: 7152 bytes, tx checksumming: ok]
[ 5.440000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 5.444000] ehci-pci: EHCI PCI platform driver
[ 5.452000] ehci-pci 0000:00:0e.5: EHCI Host Controller
[ 5.456000] ehci-pci 0000:00:0e.5: new USB bus registered, assigned bus number 1
[ 5.464000] ehci-pci 0000:00:0e.5: irq 11, io mem 0x50071000
[ 5.676000] ata1.00: ATA-8: WDC WD1600BEVS-00VAT0, 11.01A11, max UDMA/133
[ 5.680000] ata1.00: 312581808 sectors, multi 16: LBA48
[ 5.808000] scsi 0:0:0:0: Direct-Access ATA WDC WD1600BEVS-0 1A11 PQ: 0 ANSI: 5
[ 5.816000] sd 0:0:0:0: [sda] 312581808 512-byte logical blocks: (160 GB/149 GiB)
[ 5.820000] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 5.828000] ata2: port disabled--ignoring
[ 5.852000] sd 0:0:0:0: [sda] Write Protect is off
[ 5.856000] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 5.880000] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 5.900000] ehci-pci 0000:00:0e.5: USB 0.0 started, EHCI 1.00
[ 5.904000] sda: sda1
[ 5.908000] hub 1-0:1.0: USB hub found
[ 5.932000] hub 1-0:1.0: 4 ports detected
[ 5.936000] sd 0:0:0:0: [sda] Attached SCSI disk
[ 5.952000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 5.956000] ohci-pci: OHCI PCI platform driver
[ 5.960000] ohci-pci 0000:00:0e.4: OHCI PCI host controller
[ 5.964000] ohci-pci 0000:00:0e.4: new USB bus registered, assigned bus number 2
[ 5.968000] ohci-pci 0000:00:0e.4: irq 11, io mem 0x50070000
[ 6.064000] hub 2-0:1.0: USB hub found
[ 6.076000] hub 2-0:1.0: 4 ports detected
[ 6.084000] usbcore: registered new interface driver usb-storage
[ 6.088000] loongson2_cpufreq: Loongson-2F CPU frequency driver
[ 6.092000] usbcore: registered new interface driver usbhid
[ 6.096000] usbhid: USB HID core driver
[ 6.100000] NET: Registered protocol family 17
[ 6.172000] Freeing unused kernel memory: 2048K
[ 6.176000] This architecture does not have kernel memory protection.
[ 6.180000] Run /init as init process
[ 10.396000] EXT4-fs (sda1): mounting ext3 file system using the ext4 subsystem
[ 10.452000] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null)
[ 13.004000] Adding 524256k swap on /SWAP. Priority:-2 extents:13 across:145760016k
[ 13.304000] RTL8211B Gigabit Ethernet r8169-30:00: attached PHY driver [RTL8211B Gigabit Ethernet] (mii_bus:phy_addr=r8169-30:00, irq=IGNORE)
[ 15.812000] r8169 0000:00:06.0 eth0: Link is Up - 1Gbps/Full - flow control rx/tx
-----
3) Failing PATA AMD.
[ 0.000000] Linux version 4.20.0-lemote-los_42599 (aaro@amd-fx-6350) (gcc version 7.4.0 (GCC)) #1 Sat Jan 26 19:29:46 EET 2019
[ 0.000000] memsize=256, highmemsize=256
[ 0.000000] CpuClock = 797800000
[ 0.000000] printk: bootconsole [early0] enabled
[ 0.000000] CPU0 revision is: 00006303 (ICT Loongson-2)
[ 0.000000] FPU revision is: 00000501
[ 0.000000] Checking for the multiply/shift bug... no.
[ 0.000000] Checking for the daddiu bug... no.
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 0000000010000000 @ 0000000000000000 (usable)
[ 0.000000] memory: 0000000030000000 @ 0000000010000000 (reserved)
[ 0.000000] memory: 0000000010000000 @ 0000000090000000 (usable)
[ 0.000000] memory: 0000000010000000 @ 0000000080000000 (reserved)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Primary instruction cache 64kB, VIPT, direct mapped, linesize 32 bytes.
[ 0.000000] Primary data cache 64kB, 4-way, VIPT, no aliases, linesize 32 bytes
[ 0.000000] Unified secondary cache 512kB 4-way, linesize 32 bytes.
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x0000000000000000-0x000000009fffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000000000-0x000000003fffffff]
[ 0.000000] node 0: [mem 0x0000000080000000-0x000000009fffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x000000009fffffff]
[ 0.000000] On node 0 totalpages: 98304
[ 0.000000] Normal zone: 336 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 98304 pages, LIFO batch:15
[ 0.000000] random: get_random_bytes called from start_kernel+0xa0/0x580 with crng_init=0
[ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[ 0.000000] pcpu-alloc: [0] 0
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 97968
[ 0.000000] Kernel command line: console=tty console=ttyS0,115200
[ 0.000000] Dentry cache hash table entries: 262144 (order: 7, 2097152 bytes)
[ 0.000000] Inode-cache hash table entries: 131072 (order: 6, 1048576 bytes)
[ 0.000000] Memory: 491728K/1572864K available (4784K kernel code, 465K rwdata, 876K rodata, 2048K init, 16620K bss, 1081136K reserved, 0K cma-reserved)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS: 128
[ 0.000000] Console: colour dummy device 80x25
[ 0.000000] printk: console [tty0] enabled
[ 0.000000] sched_clock: 64 bits at 250 Hz, resolution 4000000ns, wraps every 9007199254000000ns
[ 0.004000] Calibrating delay loop... 528.38 BogoMIPS (lpj=1056768)
[ 0.040000] pid_max: default: 32768 minimum: 301
[ 0.044000] Mount-cache hash table entries: 4096 (order: 1, 32768 bytes)
[ 0.048000] Mountpoint-cache hash table entries: 4096 (order: 1, 32768 bytes)
[ 0.052000] Checking for the daddi bug... no.
[ 0.060000] devtmpfs: initialized
[ 0.064000] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
[ 0.068000] futex hash table entries: 256 (order: -2, 6144 bytes)
[ 0.072000] NET: Registered protocol family 16
[ 0.076000] clocksource: mfgpt: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 133486551712 ns
[ 0.124000] SCSI subsystem initialized
[ 0.128000] libata version 3.00 loaded.
[ 0.128000] usbcore: registered new interface driver usbfs
[ 0.132000] usbcore: registered new interface driver hub
[ 0.136000] usbcore: registered new device driver usb
[ 0.144000] PCI host bridge to bus 0000:00
[ 0.148000] pci_bus 0000:00: root bus resource [mem 0x40000000-0x7fffffff]
[ 0.152000] pci_bus 0000:00: root bus resource [io 0x4000-0xffff]
[ 0.156000] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0]
[ 0.160000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[ 0.164000] pci 0000:00:06.0: [10ec:8169] type 00 class 0x020000
[ 0.164000] pci 0000:00:06.0: reg 0x10: [io 0xb100-0xb1ff]
[ 0.164000] pci 0000:00:06.0: reg 0x14: [mem 0x04075000-0x040750ff]
[ 0.164000] pci 0000:00:06.0: reg 0x30: [mem 0x04040000-0x0405ffff pref]
[ 0.164000] pci 0000:00:06.0: supports D1 D2
[ 0.164000] pci 0000:00:06.0: PME# supported from D1 D2 D3hot
[ 0.164000] pci 0000:00:08.0: [1039:0325] type 00 class 0x030000
[ 0.164000] pci 0000:00:08.0: reg 0x10: [mem 0x40000000-0x4fffffff pref]
[ 0.164000] pci 0000:00:08.0: reg 0x14: [mem 0x04000000-0x0403ffff]
[ 0.164000] pci 0000:00:08.0: reg 0x18: [io 0xb300-0xb37f]
[ 0.164000] pci 0000:00:08.0: reg 0x30: [mem 0x04060000-0x0406ffff pref]
[ 0.164000] pci 0000:00:08.0: supports D1 D2
[ 0.164000] pci 0000:00:0e.0: [1022:2090] type 00 class 0x060100
[ 0.164000] pci 0000:00:0e.0: reg 0x10: [io 0xb410-0xb417]
[ 0.164000] pci 0000:00:0e.0: reg 0x14: [io 0xb000-0xb0ff]
[ 0.164000] pci 0000:00:0e.0: reg 0x18: [io 0xb380-0xb3bf]
[ 0.164000] pci 0000:00:0e.0: reg 0x20: [io 0xb280-0xb2ff]
[ 0.164000] pci 0000:00:0e.0: reg 0x24: [io 0xb3c0-0xb3df]
[ 0.164000] pci 0000:00:0e.2: [1022:209a] type 00 class 0x010180
[ 0.164000] pci 0000:00:0e.2: reg 0x20: [io 0xb400-0xb40f]
[ 0.164000] pci 0000:00:0e.2: legacy IDE quirk: reg 0x10: [io 0x01f0-0x01f7]
[ 0.168000] pci 0000:00:0e.2: legacy IDE quirk: reg 0x14: [io 0x03f6]
[ 0.172000] pci 0000:00:0e.2: legacy IDE quirk: reg 0x18: [io 0x0170-0x0177]
[ 0.176000] pci 0000:00:0e.2: legacy IDE quirk: reg 0x1c: [io 0x0376]
[ 0.180000] pci 0000:00:0e.3: [1022:2093] type 00 class 0x040100
[ 0.180000] pci 0000:00:0e.3: reg 0x10: [io 0xb200-0xb27f]
[ 0.180000] pci 0000:00:0e.4: [1022:2094] type 00 class 0x0c0310
[ 0.180000] pci 0000:00:0e.4: reg 0x10: [mem 0x04074000-0x04074fff]
[ 0.180000] pci 0000:00:0e.5: [1022:2095] type 00 class 0x0c0320
[ 0.180000] pci 0000:00:0e.5: reg 0x10: [mem 0x04073000-0x04073fff]
[ 0.180000] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 00
[ 0.180000] pci 0000:00:08.0: BAR 0: assigned [mem 0x40000000-0x4fffffff pref]
[ 0.184000] pci 0000:00:08.0: BAR 1: assigned [mem 0x50000000-0x5003ffff]
[ 0.188000] pci 0000:00:06.0: BAR 6: assigned [mem 0x50040000-0x5005ffff pref]
[ 0.192000] pci 0000:00:08.0: BAR 6: assigned [mem 0x50060000-0x5006ffff pref]
[ 0.196000] pci 0000:00:0e.4: BAR 0: assigned [mem 0x50070000-0x50070fff]
[ 0.200000] pci 0000:00:0e.5: BAR 0: assigned [mem 0x50071000-0x50071fff]
[ 0.204000] pci 0000:00:06.0: BAR 0: assigned [io 0x4000-0x40ff]
[ 0.208000] pci 0000:00:06.0: BAR 1: assigned [mem 0x50072000-0x500720ff]
[ 0.212000] pci 0000:00:0e.0: BAR 1: assigned [io 0x4400-0x44ff]
[ 0.216000] pci 0000:00:08.0: BAR 2: assigned [io 0x4800-0x487f]
[ 0.220000] pci 0000:00:0e.0: BAR 4: assigned [io 0x4880-0x48ff]
[ 0.224000] pci 0000:00:0e.3: BAR 0: assigned [io 0x4c00-0x4c7f]
[ 0.228000] pci 0000:00:0e.0: BAR 2: assigned [io 0x4c80-0x4cbf]
[ 0.232000] pci 0000:00:0e.0: BAR 5: assigned [io 0x4cc0-0x4cdf]
[ 0.236000] pci 0000:00:0e.2: BAR 4: assigned [io 0x4ce0-0x4cef]
[ 0.240000] pci 0000:00:0e.0: BAR 0: assigned [io 0x4cf0-0x4cf7]
[ 0.244000] clocksource: Switched to clocksource mfgpt
[ 0.272000] NET: Registered protocol family 2
[ 0.276000] tcp_listen_portaddr_hash hash table entries: 1024 (order: 0, 16384 bytes)
[ 0.280000] TCP established hash table entries: 16384 (order: 3, 131072 bytes)
[ 0.284000] TCP bind hash table entries: 16384 (order: 3, 131072 bytes)
[ 0.288000] TCP: Hash tables configured (established 16384 bind 16384)
[ 0.292000] UDP hash table entries: 1024 (order: 1, 32768 bytes)
[ 0.296000] UDP-Lite hash table entries: 1024 (order: 1, 32768 bytes)
[ 0.300000] NET: Registered protocol family 1
[ 0.304000] pci 0000:00:0e.4: enabling device (0000 -> 0002)
[ 0.308000] PCI: CLS 32 bytes, default 32
[ 0.892000] random: fast init done
[ 1.736000] workingset: timestamp_bits=62 max_order=15 bucket_order=0
[ 2.168000] NET: Registered protocol family 38
[ 2.172000] io scheduler noop registered
[ 2.176000] io scheduler cfq registered (default)
[ 2.180000] slot: 8, pin: 1, irq: 38
[ 2.184000] sisfb 0000:00:08.0: Invalid PCI ROM header signature: expecting 0xaa55, got 0x3030
[ 2.188000] sisfb: Video ROM not found
[ 2.192000] sisfb: Video RAM at 0x40000000, mapped to 0x9000000040000000, size 32768k
[ 2.196000] sisfb: MMIO at 0x50000000, mapped to 0x9000000050000000, size 256k
[ 2.200000] sisfb: Memory heap starting at 32160K, size 32K
[ 3.488000] sisfb: Detected SiS301C video bridge
[ 3.572000] sisfb: Detected 1280x1024 flat panel
[ 3.652000] sisfb: CRT1 DDC probing failed
[ 3.656000] sisfb: Default mode is 1280x1024x8 (60Hz)
[ 3.660000] sisfb: Initial vbflags 0x10000022
[ 3.736000] Console: switching to colour frame buffer device 160x64
[ 3.796000] sisfb: 2D acceleration is enabled, y-panning enabled (auto-max)
[ 3.800000] fb0: SiS 315PRO frame buffer device version 1.8.9
[ 3.804000] sisfb: Copyright (C) 2001-2005 Thomas Winischhofer
[ 3.812000] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[ 3.960000] printk: console [ttyS0] disabled
[ 3.968000] serial8250.0: ttyS0 at I/O 0x2f8 (irq = 3, base_baud = 115200) is a 16550A
[ 3.972000] printk: console [ttyS0] enabled
[ 3.976000] printk: bootconsole [early0] disabled
[ 4.628000] brd: module loaded
[ 4.740000] loop: module loaded
[ 4.744000] pata_amd 0000:00:0e.2: version 0.4.1
[ 4.860000] random: crng init done
[ 5.320000] scsi host0: pata_amd
[ 5.608000] scsi host1: pata_amd
[ 5.612000] ata1: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0x4ce0 irq 14
[ 5.616000] ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0x4ce8 irq 15
[ 5.624000] slot: 6, pin: 1, irq: 36
[ 5.628000] r8169 0000:00:06.0: not PCI Express
[ 5.636000] libphy: r8169: probed
[ 5.648000] r8169 0000:00:06.0 eth0: RTL8169sc/8110sc, 00:23:9e:00:0f:54, XID 98000000, IRQ 36
[ 5.652000] r8169 0000:00:06.0 eth0: jumbo features [frames: 7152 bytes, tx checksumming: ok]
[ 5.656000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 5.660000] ehci-pci: EHCI PCI platform driver
[ 5.664000] ehci-pci 0000:00:0e.5: EHCI Host Controller
[ 5.668000] ehci-pci 0000:00:0e.5: new USB bus registered, assigned bus number 1
[ 5.676000] ehci-pci 0000:00:0e.5: irq 11, io mem 0x50071000
[ 5.736000] irq 14: nobody cared (try booting with the "irqpoll" option)
[ 5.736000] CPU: 0 PID: 551 Comm: block_add.sh Not tainted 4.20.0-lemote-los_42599 #1
[ 5.736000] Stack : 00000000000000a3 00000000000000a4 ffffffffcfffffff 980000009f023d78
[ 5.736000] 82327644e4724700 0000000000000000 0000000000000000 ffffffff81a40000
[ 5.736000] 00000000000000a4 0000000000000007 0000000000000000 ffffffff806d7388
[ 5.736000] 0000000000000000 0000000000000004 0000000000000002 980000009fb533d0
[ 5.736000] 9000000040121b08 ffffffff80790000 ffffff0000000000 000000000000000e
[ 5.736000] 0000000077b3f306 0000000077b2f930 0000000077b41aac 0000000000000000
[ 5.736000] 0000000000000003 ffffffffffffffff 9000000040121b0c 0000000000000000
[ 5.736000] ffffffff80a10000 980000009f490000 980000009f023d70 000000007fc763f0
[ 5.736000] ffffffff80262a38 0000000000000000 0000000000000000 0000000000000000
[ 5.736000] 0000000000000000 82327644e4724700 ffffffff8020f504 82327644e4724700
[ 5.736000] ...
[ 5.736000] Call Trace:
[ 5.736000] [<ffffffff8020f504>] show_stack+0x90/0x140
[ 5.736000] [<ffffffff80262a38>] __report_bad_irq+0x44/0xf4
[ 5.736000] [<ffffffff80262ddc>] note_interrupt+0x274/0x318
[ 5.736000] [<ffffffff8025fec4>] handle_irq_event_percpu+0x60/0x9c
[ 5.736000] [<ffffffff8025ff3c>] handle_irq_event+0x3c/0x70
[ 5.736000] [<ffffffff80263f78>] handle_level_irq+0x10c/0x148
[ 5.736000] [<ffffffff8025f498>] generic_handle_irq+0x34/0x50
[ 5.736000] [<ffffffff806aa298>] do_IRQ+0x18/0x24
[ 5.736000] [<ffffffff80208ec4>] handle_int+0x17c/0x188
[ 5.736000] handlers:
[ 5.736000] [<0000000059069b40>] ata_bmdma_interrupt
[ 5.736000] Disabling IRQ #14
[ 5.944000] ata1.00: ATA-8: WDC WD1600BEVS-00VAT0, 11.01A11, max UDMA/133
[ 5.948000] ata1.00: 312581808 sectors, multi 16: LBA48
[ 5.980000] ehci-pci 0000:00:0e.5: USB 0.0 started, EHCI 1.00
[ 5.984000] hub 1-0:1.0: USB hub found
[ 5.996000] hub 1-0:1.0: 4 ports detected
[ 6.004000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 6.008000] ohci-pci: OHCI PCI platform driver
[ 6.012000] ohci-pci 0000:00:0e.4: OHCI PCI host controller
[ 6.016000] ohci-pci 0000:00:0e.4: new USB bus registered, assigned bus number 2
[ 6.020000] ohci-pci 0000:00:0e.4: irq 11, io mem 0x50070000
[ 6.048000] scsi 0:0:0:0: Direct-Access ATA WDC WD1600BEVS-0 1A11 PQ: 0 ANSI: 5
[ 6.052000] sd 0:0:0:0: [sda] 312581808 512-byte logical blocks: (160 GB/149 GiB)
[ 6.056000] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 6.060000] ata2: port disabled--ignoring
[ 6.076000] sd 0:0:0:0: [sda] Write Protect is off
[ 6.080000] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 6.092000] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 6.136000] hub 2-0:1.0: USB hub found
[ 6.148000] hub 2-0:1.0: 4 ports detected
[ 6.152000] usbcore: registered new interface driver usb-storage
[ 6.156000] loongson2_cpufreq: Loongson-2F CPU frequency driver
[ 6.160000] usbcore: registered new interface driver usbhid
[ 6.164000] usbhid: USB HID core driver
[ 6.172000] NET: Registered protocol family 17
[ 6.360000] sda: sda1
[ 6.376000] sd 0:0:0:0: [sda] Attached SCSI disk
[ 6.388000] Freeing unused kernel memory: 2048K
[ 6.392000] This architecture does not have kernel memory protection.
[ 6.396000] Run /init as init process
[ 36.728000] EXT4-fs (sda1): mounting ext3 file system using the ext4 subsystem
[ 37.876000] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null)
[ 65.500000] RTL8211B Gigabit Ethernet r8169-30:00: attached PHY driver [RTL8211B Gigabit Ethernet] (mii_bus:phy_addr=r8169-30:00, irq=IGNORE)
[ 69.920000] r8169 0000:00:06.0 eth0: Link is Up - 1Gbps/Full - flow control rx/tx
[ 76.456000] Adding 524256k swap on /SWAP. Priority:-2 extents:13 across:145760016k
4) Working PATA CS5536.
[ 0.000000] Linux version 4.20.0-lemote-los_42599+ (aaro@amd-fx-6350) (gcc version 7.4.0 (GCC)) #1 Sat Jan 26 19:42:09 EET 2019
[ 0.000000] memsize=256, highmemsize=256
[ 0.000000] CpuClock = 797780000
[ 0.000000] printk: bootconsole [early0] enabled
[ 0.000000] CPU0 revision is: 00006303 (ICT Loongson-2)
[ 0.000000] FPU revision is: 00000501
[ 0.000000] Checking for the multiply/shift bug... no.
[ 0.000000] Checking for the daddiu bug... no.
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 0000000010000000 @ 0000000000000000 (usable)
[ 0.000000] memory: 0000000030000000 @ 0000000010000000 (reserved)
[ 0.000000] memory: 0000000010000000 @ 0000000090000000 (usable)
[ 0.000000] memory: 0000000010000000 @ 0000000080000000 (reserved)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Primary instruction cache 64kB, VIPT, direct mapped, linesize 32 bytes.
[ 0.000000] Primary data cache 64kB, 4-way, VIPT, no aliases, linesize 32 bytes
[ 0.000000] Unified secondary cache 512kB 4-way, linesize 32 bytes.
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x0000000000000000-0x000000009fffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000000000-0x000000003fffffff]
[ 0.000000] node 0: [mem 0x0000000080000000-0x000000009fffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x000000009fffffff]
[ 0.000000] On node 0 totalpages: 98304
[ 0.000000] Normal zone: 336 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 98304 pages, LIFO batch:15
[ 0.000000] random: get_random_bytes called from start_kernel+0xa0/0x580 with crng_init=0
[ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[ 0.000000] pcpu-alloc: [0] 0
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 97968
[ 0.000000] Kernel command line: console=tty console=ttyS0,115200
[ 0.000000] Dentry cache hash table entries: 262144 (order: 7, 2097152 bytes)
[ 0.000000] Inode-cache hash table entries: 131072 (order: 6, 1048576 bytes)
[ 0.000000] Memory: 491728K/1572864K available (4782K kernel code, 471K rwdata, 872K rodata, 2048K init, 16620K bss, 1081136K reserved, 0K cma-reserved)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS: 128
[ 0.000000] Console: colour dummy device 80x25
[ 0.000000] printk: console [tty0] enabled
[ 0.000000] sched_clock: 64 bits at 250 Hz, resolution 4000000ns, wraps every 9007199254000000ns
[ 0.004000] Calibrating delay loop... 528.38 BogoMIPS (lpj=1056768)
[ 0.040000] pid_max: default: 32768 minimum: 301
[ 0.044000] Mount-cache hash table entries: 4096 (order: 1, 32768 bytes)
[ 0.048000] Mountpoint-cache hash table entries: 4096 (order: 1, 32768 bytes)
[ 0.052000] Checking for the daddi bug... no.
[ 0.060000] devtmpfs: initialized
[ 0.064000] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
[ 0.068000] futex hash table entries: 256 (order: -2, 6144 bytes)
[ 0.072000] NET: Registered protocol family 16
[ 0.076000] clocksource: mfgpt: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 133486551712 ns
[ 0.124000] SCSI subsystem initialized
[ 0.128000] libata version 3.00 loaded.
[ 0.128000] usbcore: registered new interface driver usbfs
[ 0.132000] usbcore: registered new interface driver hub
[ 0.136000] usbcore: registered new device driver usb
[ 0.140000] PCI host bridge to bus 0000:00
[ 0.144000] pci_bus 0000:00: root bus resource [mem 0x40000000-0x7fffffff]
[ 0.148000] pci_bus 0000:00: root bus resource [io 0x4000-0xffff]
[ 0.152000] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0]
[ 0.156000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[ 0.160000] pci 0000:00:06.0: [10ec:8169] type 00 class 0x020000
[ 0.160000] pci 0000:00:06.0: reg 0x10: [io 0xb100-0xb1ff]
[ 0.160000] pci 0000:00:06.0: reg 0x14: [mem 0x04075000-0x040750ff]
[ 0.160000] pci 0000:00:06.0: reg 0x30: [mem 0x04040000-0x0405ffff pref]
[ 0.164000] pci 0000:00:06.0: supports D1 D2
[ 0.164000] pci 0000:00:06.0: PME# supported from D1 D2 D3hot
[ 0.164000] pci 0000:00:08.0: [1039:0325] type 00 class 0x030000
[ 0.164000] pci 0000:00:08.0: reg 0x10: [mem 0x40000000-0x4fffffff pref]
[ 0.164000] pci 0000:00:08.0: reg 0x14: [mem 0x04000000-0x0403ffff]
[ 0.164000] pci 0000:00:08.0: reg 0x18: [io 0xb300-0xb37f]
[ 0.164000] pci 0000:00:08.0: reg 0x30: [mem 0x04060000-0x0406ffff pref]
[ 0.164000] pci 0000:00:08.0: supports D1 D2
[ 0.164000] pci 0000:00:0e.0: [1022:2090] type 00 class 0x060100
[ 0.164000] pci 0000:00:0e.0: reg 0x10: [io 0xb410-0xb417]
[ 0.164000] pci 0000:00:0e.0: reg 0x14: [io 0xb000-0xb0ff]
[ 0.164000] pci 0000:00:0e.0: reg 0x18: [io 0xb380-0xb3bf]
[ 0.164000] pci 0000:00:0e.0: reg 0x20: [io 0xb280-0xb2ff]
[ 0.164000] pci 0000:00:0e.0: reg 0x24: [io 0xb3c0-0xb3df]
[ 0.164000] pci 0000:00:0e.2: [1022:209a] type 00 class 0x010180
[ 0.164000] pci 0000:00:0e.2: reg 0x20: [io 0xb400-0xb40f]
[ 0.164000] pci 0000:00:0e.2: legacy IDE quirk: reg 0x10: [io 0x01f0-0x01f7]
[ 0.168000] pci 0000:00:0e.2: legacy IDE quirk: reg 0x14: [io 0x03f6]
[ 0.172000] pci 0000:00:0e.2: legacy IDE quirk: reg 0x18: [io 0x0170-0x0177]
[ 0.176000] pci 0000:00:0e.2: legacy IDE quirk: reg 0x1c: [io 0x0376]
[ 0.180000] pci 0000:00:0e.3: [1022:2093] type 00 class 0x040100
[ 0.180000] pci 0000:00:0e.3: reg 0x10: [io 0xb200-0xb27f]
[ 0.180000] pci 0000:00:0e.4: [1022:2094] type 00 class 0x0c0310
[ 0.180000] pci 0000:00:0e.4: reg 0x10: [mem 0x04074000-0x04074fff]
[ 0.180000] pci 0000:00:0e.5: [1022:2095] type 00 class 0x0c0320
[ 0.180000] pci 0000:00:0e.5: reg 0x10: [mem 0x04073000-0x04073fff]
[ 0.180000] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 00
[ 0.180000] pci 0000:00:08.0: BAR 0: assigned [mem 0x40000000-0x4fffffff pref]
[ 0.184000] pci 0000:00:08.0: BAR 1: assigned [mem 0x50000000-0x5003ffff]
[ 0.188000] pci 0000:00:06.0: BAR 6: assigned [mem 0x50040000-0x5005ffff pref]
[ 0.192000] pci 0000:00:08.0: BAR 6: assigned [mem 0x50060000-0x5006ffff pref]
[ 0.196000] pci 0000:00:0e.4: BAR 0: assigned [mem 0x50070000-0x50070fff]
[ 0.200000] pci 0000:00:0e.5: BAR 0: assigned [mem 0x50071000-0x50071fff]
[ 0.204000] pci 0000:00:06.0: BAR 0: assigned [io 0x4000-0x40ff]
[ 0.208000] pci 0000:00:06.0: BAR 1: assigned [mem 0x50072000-0x500720ff]
[ 0.212000] pci 0000:00:0e.0: BAR 1: assigned [io 0x4400-0x44ff]
[ 0.216000] pci 0000:00:08.0: BAR 2: assigned [io 0x4800-0x487f]
[ 0.220000] pci 0000:00:0e.0: BAR 4: assigned [io 0x4880-0x48ff]
[ 0.224000] pci 0000:00:0e.3: BAR 0: assigned [io 0x4c00-0x4c7f]
[ 0.228000] pci 0000:00:0e.0: BAR 2: assigned [io 0x4c80-0x4cbf]
[ 0.232000] pci 0000:00:0e.0: BAR 5: assigned [io 0x4cc0-0x4cdf]
[ 0.236000] pci 0000:00:0e.2: BAR 4: assigned [io 0x4ce0-0x4cef]
[ 0.240000] pci 0000:00:0e.0: BAR 0: assigned [io 0x4cf0-0x4cf7]
[ 0.244000] clocksource: Switched to clocksource mfgpt
[ 0.272000] NET: Registered protocol family 2
[ 0.276000] tcp_listen_portaddr_hash hash table entries: 1024 (order: 0, 16384 bytes)
[ 0.280000] TCP established hash table entries: 16384 (order: 3, 131072 bytes)
[ 0.288000] TCP bind hash table entries: 16384 (order: 3, 131072 bytes)
[ 0.292000] TCP: Hash tables configured (established 16384 bind 16384)
[ 0.296000] UDP hash table entries: 1024 (order: 1, 32768 bytes)
[ 0.300000] UDP-Lite hash table entries: 1024 (order: 1, 32768 bytes)
[ 0.304000] NET: Registered protocol family 1
[ 0.308000] pci 0000:00:0e.4: enabling device (0000 -> 0002)
[ 0.312000] PCI: CLS 32 bytes, default 32
[ 0.896000] random: fast init done
[ 1.724000] workingset: timestamp_bits=62 max_order=15 bucket_order=0
[ 2.164000] NET: Registered protocol family 38
[ 2.168000] io scheduler noop registered
[ 2.172000] io scheduler cfq registered (default)
[ 2.180000] slot: 8, pin: 1, irq: 38
[ 2.184000] sisfb 0000:00:08.0: Invalid PCI ROM header signature: expecting 0xaa55, got 0x3030
[ 2.188000] sisfb: Video ROM not found
[ 2.192000] sisfb: Video RAM at 0x40000000, mapped to 0x9000000040000000, size 32768k
[ 2.196000] sisfb: MMIO at 0x50000000, mapped to 0x9000000050000000, size 256k
[ 2.200000] sisfb: Memory heap starting at 32160K, size 32K
[ 3.484000] sisfb: Detected SiS301C video bridge
[ 3.564000] sisfb: Detected 1280x1024 flat panel
[ 3.648000] sisfb: CRT1 DDC probing failed
[ 3.652000] sisfb: Default mode is 1280x1024x8 (60Hz)
[ 3.656000] sisfb: Initial vbflags 0x10000022
[ 3.728000] Console: switching to colour frame buffer device 160x64
[ 3.784000] sisfb: 2D acceleration is enabled, y-panning enabled (auto-max)
[ 3.788000] fb0: SiS 315PRO frame buffer device version 1.8.9
[ 3.792000] sisfb: Copyright (C) 2001-2005 Thomas Winischhofer
[ 3.808000] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[ 3.952000] printk: console [ttyS0] disabled
[ 3.960000] serial8250.0: ttyS0 at I/O 0x2f8 (irq = 3, base_baud = 115200) is a 16550A
[ 3.964000] printk: console [ttyS0] enabled
[ 3.968000] printk: bootconsole [early0] disabled
[ 4.592000] brd: module loaded
[ 4.764000] loop: module loaded
[ 4.880000] random: crng init done
[ 5.108000] scsi host0: pata_cs5536
[ 5.444000] scsi host1: pata_cs5536
[ 5.448000] ata1: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0x4ce0 irq 14
[ 5.452000] ata2: DUMMY
[ 5.460000] slot: 6, pin: 1, irq: 36
[ 5.464000] r8169 0000:00:06.0: not PCI Express
[ 5.472000] libphy: r8169: probed
[ 5.484000] r8169 0000:00:06.0 eth0: RTL8169sc/8110sc, 00:23:9e:00:0f:54, XID 98000000, IRQ 36
[ 5.488000] r8169 0000:00:06.0 eth0: jumbo features [frames: 7152 bytes, tx checksumming: ok]
[ 5.492000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 5.496000] ehci-pci: EHCI PCI platform driver
[ 5.500000] ehci-pci 0000:00:0e.5: EHCI Host Controller
[ 5.504000] ehci-pci 0000:00:0e.5: new USB bus registered, assigned bus number 1
[ 5.512000] ehci-pci 0000:00:0e.5: irq 11, io mem 0x50071000
[ 5.732000] ata1.00: ATA-8: WDC WD1600BEVS-00VAT0, 11.01A11, max UDMA/133
[ 5.736000] ata1.00: 312581808 sectors, multi 16: LBA48
[ 5.740000] ata1.00: limited to UDMA/33 due to 40-wire cable
[ 5.884000] scsi 0:0:0:0: Direct-Access ATA WDC WD1600BEVS-0 1A11 PQ: 0 ANSI: 5
[ 5.888000] sd 0:0:0:0: [sda] 312581808 512-byte logical blocks: (160 GB/149 GiB)
[ 5.892000] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 5.920000] sd 0:0:0:0: [sda] Write Protect is off
[ 5.924000] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 5.936000] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 5.952000] ehci-pci 0000:00:0e.5: USB 0.0 started, EHCI 1.00
[ 5.960000] sda: sda1
[ 5.964000] hub 1-0:1.0: USB hub found
[ 5.988000] hub 1-0:1.0: 4 ports detected
[ 5.992000] sd 0:0:0:0: [sda] Attached SCSI disk
[ 6.004000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 6.008000] ohci-pci: OHCI PCI platform driver
[ 6.012000] ohci-pci 0000:00:0e.4: OHCI PCI host controller
[ 6.016000] ohci-pci 0000:00:0e.4: new USB bus registered, assigned bus number 2
[ 6.024000] ohci-pci 0000:00:0e.4: irq 11, io mem 0x50070000
[ 6.120000] hub 2-0:1.0: USB hub found
[ 6.132000] hub 2-0:1.0: 4 ports detected
[ 6.140000] usbcore: registered new interface driver usb-storage
[ 6.144000] loongson2_cpufreq: Loongson-2F CPU frequency driver
[ 6.148000] usbcore: registered new interface driver usbhid
[ 6.152000] usbhid: USB HID core driver
[ 6.156000] NET: Registered protocol family 17
[ 6.228000] Freeing unused kernel memory: 2048K
[ 6.232000] This architecture does not have kernel memory protection.
[ 6.236000] Run /init as init process
[ 10.512000] EXT4-fs (sda1): mounting ext3 file system using the ext4 subsystem
[ 10.576000] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null)
[ 13.196000] Adding 524256k swap on /SWAP. Priority:-2 extents:13 across:145760016k
[ 13.488000] RTL8211B Gigabit Ethernet r8169-30:00: attached PHY driver [RTL8211B Gigabit Ethernet] (mii_bus:phy_addr=r8169-30:00, irq=IGNORE)
[ 16.260000] r8169 0000:00:06.0 eth0: Link is Up - 1Gbps/Full - flow control rx/tx
-----
5) Failing PATA CS5536.
[ 0.000000] Linux version 4.20.0-lemote-los_42599+ (aaro@amd-fx-6350) (gcc version 7.4.0 (GCC)) #1 Sat Jan 26 19:42:09 EET 2019
[ 0.000000] memsize=256, highmemsize=256
[ 0.000000] CpuClock = 797800000
[ 0.000000] printk: bootconsole [early0] enabled
[ 0.000000] CPU0 revision is: 00006303 (ICT Loongson-2)
[ 0.000000] FPU revision is: 00000501
[ 0.000000] Checking for the multiply/shift bug... no.
[ 0.000000] Checking for the daddiu bug... no.
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 0000000010000000 @ 0000000000000000 (usable)
[ 0.000000] memory: 0000000030000000 @ 0000000010000000 (reserved)
[ 0.000000] memory: 0000000010000000 @ 0000000090000000 (usable)
[ 0.000000] memory: 0000000010000000 @ 0000000080000000 (reserved)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Primary instruction cache 64kB, VIPT, direct mapped, linesize 32 bytes.
[ 0.000000] Primary data cache 64kB, 4-way, VIPT, no aliases, linesize 32 bytes
[ 0.000000] Unified secondary cache 512kB 4-way, linesize 32 bytes.
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x0000000000000000-0x000000009fffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000000000-0x000000003fffffff]
[ 0.000000] node 0: [mem 0x0000000080000000-0x000000009fffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x000000009fffffff]
[ 0.000000] On node 0 totalpages: 98304
[ 0.000000] Normal zone: 336 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 98304 pages, LIFO batch:15
[ 0.000000] random: get_random_bytes called from start_kernel+0xa0/0x580 with crng_init=0
[ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[ 0.000000] pcpu-alloc: [0] 0
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 97968
[ 0.000000] Kernel command line: console=tty console=ttyS0,115200
[ 0.000000] Dentry cache hash table entries: 262144 (order: 7, 2097152 bytes)
[ 0.000000] Inode-cache hash table entries: 131072 (order: 6, 1048576 bytes)
[ 0.000000] Memory: 491728K/1572864K available (4782K kernel code, 471K rwdata, 872K rodata, 2048K init, 16620K bss, 1081136K reserved, 0K cma-reserved)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS: 128
[ 0.000000] Console: colour dummy device 80x25
[ 0.000000] printk: console [tty0] enabled
[ 0.000000] sched_clock: 64 bits at 250 Hz, resolution 4000000ns, wraps every 9007199254000000ns
[ 0.004000] Calibrating delay loop... 528.38 BogoMIPS (lpj=1056768)
[ 0.040000] pid_max: default: 32768 minimum: 301
[ 0.044000] Mount-cache hash table entries: 4096 (order: 1, 32768 bytes)
[ 0.048000] Mountpoint-cache hash table entries: 4096 (order: 1, 32768 bytes)
[ 0.052000] Checking for the daddi bug... no.
[ 0.060000] devtmpfs: initialized
[ 0.064000] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
[ 0.068000] futex hash table entries: 256 (order: -2, 6144 bytes)
[ 0.072000] NET: Registered protocol family 16
[ 0.076000] clocksource: mfgpt: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 133486551712 ns
[ 0.124000] SCSI subsystem initialized
[ 0.128000] libata version 3.00 loaded.
[ 0.128000] usbcore: registered new interface driver usbfs
[ 0.132000] usbcore: registered new interface driver hub
[ 0.136000] usbcore: registered new device driver usb
[ 0.140000] PCI host bridge to bus 0000:00
[ 0.144000] pci_bus 0000:00: root bus resource [mem 0x40000000-0x7fffffff]
[ 0.148000] pci_bus 0000:00: root bus resource [io 0x4000-0xffff]
[ 0.152000] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0]
[ 0.156000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[ 0.160000] pci 0000:00:06.0: [10ec:8169] type 00 class 0x020000
[ 0.160000] pci 0000:00:06.0: reg 0x10: [io 0xb100-0xb1ff]
[ 0.160000] pci 0000:00:06.0: reg 0x14: [mem 0x04075000-0x040750ff]
[ 0.160000] pci 0000:00:06.0: reg 0x30: [mem 0x04040000-0x0405ffff pref]
[ 0.164000] pci 0000:00:06.0: supports D1 D2
[ 0.164000] pci 0000:00:06.0: PME# supported from D1 D2 D3hot
[ 0.164000] pci 0000:00:08.0: [1039:0325] type 00 class 0x030000
[ 0.164000] pci 0000:00:08.0: reg 0x10: [mem 0x40000000-0x4fffffff pref]
[ 0.164000] pci 0000:00:08.0: reg 0x14: [mem 0x04000000-0x0403ffff]
[ 0.164000] pci 0000:00:08.0: reg 0x18: [io 0xb300-0xb37f]
[ 0.164000] pci 0000:00:08.0: reg 0x30: [mem 0x04060000-0x0406ffff pref]
[ 0.164000] pci 0000:00:08.0: supports D1 D2
[ 0.164000] pci 0000:00:0e.0: [1022:2090] type 00 class 0x060100
[ 0.164000] pci 0000:00:0e.0: reg 0x10: [io 0xb410-0xb417]
[ 0.164000] pci 0000:00:0e.0: reg 0x14: [io 0xb000-0xb0ff]
[ 0.164000] pci 0000:00:0e.0: reg 0x18: [io 0xb380-0xb3bf]
[ 0.164000] pci 0000:00:0e.0: reg 0x20: [io 0xb280-0xb2ff]
[ 0.164000] pci 0000:00:0e.0: reg 0x24: [io 0xb3c0-0xb3df]
[ 0.164000] pci 0000:00:0e.2: [1022:209a] type 00 class 0x010180
[ 0.164000] pci 0000:00:0e.2: reg 0x20: [io 0xb400-0xb40f]
[ 0.164000] pci 0000:00:0e.2: legacy IDE quirk: reg 0x10: [io 0x01f0-0x01f7]
[ 0.168000] pci 0000:00:0e.2: legacy IDE quirk: reg 0x14: [io 0x03f6]
[ 0.172000] pci 0000:00:0e.2: legacy IDE quirk: reg 0x18: [io 0x0170-0x0177]
[ 0.176000] pci 0000:00:0e.2: legacy IDE quirk: reg 0x1c: [io 0x0376]
[ 0.180000] pci 0000:00:0e.3: [1022:2093] type 00 class 0x040100
[ 0.180000] pci 0000:00:0e.3: reg 0x10: [io 0xb200-0xb27f]
[ 0.180000] pci 0000:00:0e.4: [1022:2094] type 00 class 0x0c0310
[ 0.180000] pci 0000:00:0e.4: reg 0x10: [mem 0x04074000-0x04074fff]
[ 0.180000] pci 0000:00:0e.5: [1022:2095] type 00 class 0x0c0320
[ 0.180000] pci 0000:00:0e.5: reg 0x10: [mem 0x04073000-0x04073fff]
[ 0.180000] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 00
[ 0.180000] pci 0000:00:08.0: BAR 0: assigned [mem 0x40000000-0x4fffffff pref]
[ 0.184000] pci 0000:00:08.0: BAR 1: assigned [mem 0x50000000-0x5003ffff]
[ 0.188000] pci 0000:00:06.0: BAR 6: assigned [mem 0x50040000-0x5005ffff pref]
[ 0.192000] pci 0000:00:08.0: BAR 6: assigned [mem 0x50060000-0x5006ffff pref]
[ 0.196000] pci 0000:00:0e.4: BAR 0: assigned [mem 0x50070000-0x50070fff]
[ 0.200000] pci 0000:00:0e.5: BAR 0: assigned [mem 0x50071000-0x50071fff]
[ 0.204000] pci 0000:00:06.0: BAR 0: assigned [io 0x4000-0x40ff]
[ 0.208000] pci 0000:00:06.0: BAR 1: assigned [mem 0x50072000-0x500720ff]
[ 0.212000] pci 0000:00:0e.0: BAR 1: assigned [io 0x4400-0x44ff]
[ 0.216000] pci 0000:00:08.0: BAR 2: assigned [io 0x4800-0x487f]
[ 0.220000] pci 0000:00:0e.0: BAR 4: assigned [io 0x4880-0x48ff]
[ 0.224000] pci 0000:00:0e.3: BAR 0: assigned [io 0x4c00-0x4c7f]
[ 0.228000] pci 0000:00:0e.0: BAR 2: assigned [io 0x4c80-0x4cbf]
[ 0.232000] pci 0000:00:0e.0: BAR 5: assigned [io 0x4cc0-0x4cdf]
[ 0.236000] pci 0000:00:0e.2: BAR 4: assigned [io 0x4ce0-0x4cef]
[ 0.240000] pci 0000:00:0e.0: BAR 0: assigned [io 0x4cf0-0x4cf7]
[ 0.244000] clocksource: Switched to clocksource mfgpt
[ 0.272000] NET: Registered protocol family 2
[ 0.276000] tcp_listen_portaddr_hash hash table entries: 1024 (order: 0, 16384 bytes)
[ 0.280000] TCP established hash table entries: 16384 (order: 3, 131072 bytes)
[ 0.284000] TCP bind hash table entries: 16384 (order: 3, 131072 bytes)
[ 0.288000] TCP: Hash tables configured (established 16384 bind 16384)
[ 0.292000] UDP hash table entries: 1024 (order: 1, 32768 bytes)
[ 0.296000] UDP-Lite hash table entries: 1024 (order: 1, 32768 bytes)
[ 0.300000] NET: Registered protocol family 1
[ 0.304000] pci 0000:00:0e.4: enabling device (0000 -> 0002)
[ 0.308000] PCI: CLS 32 bytes, default 32
[ 0.896000] random: fast init done
[ 1.732000] workingset: timestamp_bits=62 max_order=15 bucket_order=0
[ 2.160000] NET: Registered protocol family 38
[ 2.164000] io scheduler noop registered
[ 2.168000] io scheduler cfq registered (default)
[ 2.176000] slot: 8, pin: 1, irq: 38
[ 2.176000] sisfb 0000:00:08.0: Invalid PCI ROM header signature: expecting 0xaa55, got 0x3030
[ 2.180000] sisfb: Video ROM not found
[ 2.184000] sisfb: Video RAM at 0x40000000, mapped to 0x9000000040000000, size 32768k
[ 2.188000] sisfb: MMIO at 0x50000000, mapped to 0x9000000050000000, size 256k
[ 2.192000] sisfb: Memory heap starting at 32160K, size 32K
[ 3.472000] sisfb: Detected SiS301C video bridge
[ 3.556000] sisfb: Detected 1280x1024 flat panel
[ 3.636000] sisfb: CRT2 DDC supported
[ 3.640000] sisfb: CRT2 DDC level: 2
[ 3.848000] sisfb: Monitor range H 30-81KHz, V 56-76Hz, Max. dotclock 140MHz
[ 3.852000] sisfb: Default mode is 1280x1024x8 (60Hz)
[ 3.856000] sisfb: Initial vbflags 0x10000022
[ 3.928000] Console: switching to colour frame buffer device 160x64
[ 3.984000] sisfb: 2D acceleration is enabled, y-panning enabled (auto-max)
[ 3.988000] fb0: SiS 315PRO frame buffer device version 1.8.9
[ 3.992000] sisfb: Copyright (C) 2001-2005 Thomas Winischhofer
[ 4.048000] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[ 4.192000] printk: console [ttyS0] disabled
[ 4.200000] serial8250.0: ttyS0 at I/O 0x2f8 (irq = 3, base_baud = 115200) is a 16550A
[ 4.204000] printk: console [ttyS0] enabled
[ 4.208000] printk: bootconsole [early0] disabled
[ 4.820000] brd: module loaded
[ 4.932000] loop: module loaded
[ 5.052000] random: crng init done
[ 5.372000] scsi host0: pata_cs5536
[ 5.664000] scsi host1: pata_cs5536
[ 5.672000] ata1: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0x4ce0 irq 14
[ 5.680000] ata2: DUMMY
[ 5.684000] slot: 6, pin: 1, irq: 36
[ 5.688000] r8169 0000:00:06.0: not PCI Express
[ 5.696000] libphy: r8169: probed
[ 5.704000] r8169 0000:00:06.0 eth0: RTL8169sc/8110sc, 00:23:9e:00:0f:54, XID 98000000, IRQ 36
[ 5.708000] r8169 0000:00:06.0 eth0: jumbo features [frames: 7152 bytes, tx checksumming: ok]
[ 5.712000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 5.716000] ehci-pci: EHCI PCI platform driver
[ 5.720000] ehci-pci 0000:00:0e.5: EHCI Host Controller
[ 5.724000] ehci-pci 0000:00:0e.5: new USB bus registered, assigned bus number 1
[ 5.728000] ehci-pci 0000:00:0e.5: irq 11, io mem 0x50071000
[ 5.920000] irq 14: nobody cared (try booting with the "irqpoll" option)
[ 5.920000] CPU: 0 PID: 568 Comm: hotplug Not tainted 4.20.0-lemote-los_42599+ #1
[ 5.920000] Stack : 00000000000000a4 00000000000000a5 ffffffffcfffffff 980000009f023d78
[ 5.920000] 576a98c906c11500 0000000000000000 0000000000000000 ffffffff81a40000
[ 5.920000] 00000000000000a5 0000000000000007 0000000000000000 ffffffff806d7388
[ 5.920000] 0000000000000000 0000000000000004 0000000000000002 980000009fb42e50
[ 5.920000] 9000000040121b08 ffffffff80790000 ffffff0000000000 000000000000000e
[ 5.920000] 0000000000000003 0000000000000000 0000000000000000 0000000000000000
[ 5.920000] 0000000000000000 ffffffffffffffff 9000000040121b0c 0000000000000000
[ 5.920000] ffffffff80a10000 980000009fc30000 980000009f023d70 0000000000000000
[ 5.920000] ffffffff80262a38 0000000000000000 0000000000000000 0000000000000000
[ 5.920000] 0000000000000000 576a98c906c11500 ffffffff8020f504 576a98c906c11500
[ 5.920000] ...
[ 5.920000] Call Trace:
[ 5.920000] [<ffffffff8020f504>] show_stack+0x90/0x140
[ 5.920000] [<ffffffff80262a38>] __report_bad_irq+0x44/0xf4
[ 5.920000] [<ffffffff80262ddc>] note_interrupt+0x274/0x318
[ 5.920000] [<ffffffff8025fec4>] handle_irq_event_percpu+0x60/0x9c
[ 5.920000] [<ffffffff8025ff3c>] handle_irq_event+0x3c/0x70
[ 5.920000] [<ffffffff80263f78>] handle_level_irq+0x10c/0x148
[ 5.920000] [<ffffffff8025f498>] generic_handle_irq+0x34/0x50
[ 5.920000] [<ffffffff806a9ab8>] do_IRQ+0x18/0x24
[ 5.920000] [<ffffffff80208ec4>] handle_int+0x17c/0x188
[ 5.920000] handlers:
[ 5.920000] [<000000004cce36f4>] ata_bmdma_interrupt
[ 5.920000] Disabling IRQ #14
[ 6.144000] ehci-pci 0000:00:0e.5: USB 0.0 started, EHCI 1.00
[ 6.148000] hub 1-0:1.0: USB hub found
[ 6.160000] hub 1-0:1.0: 4 ports detected
[ 6.168000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 6.172000] ohci-pci: OHCI PCI platform driver
[ 6.176000] ohci-pci 0000:00:0e.4: OHCI PCI host controller
[ 6.180000] ohci-pci 0000:00:0e.4: new USB bus registered, assigned bus number 2
[ 6.184000] ohci-pci 0000:00:0e.4: irq 11, io mem 0x50070000
[ 6.280000] ata1.00: ATA-8: WDC WD1600BEVS-00VAT0, 11.01A11, max UDMA/133
[ 6.284000] ata1.00: 312581808 sectors, multi 16: LBA48
[ 6.288000] ata1.00: limited to UDMA/33 due to 40-wire cable
[ 6.292000] hub 2-0:1.0: USB hub found
[ 6.304000] hub 2-0:1.0: 4 ports detected
[ 6.312000] usbcore: registered new interface driver usb-storage
[ 6.316000] loongson2_cpufreq: Loongson-2F CPU frequency driver
[ 6.320000] usbcore: registered new interface driver usbhid
[ 6.324000] usbhid: USB HID core driver
[ 6.328000] NET: Registered protocol family 17
[ 6.356000] scsi 0:0:0:0: Direct-Access ATA WDC WD1600BEVS-0 1A11 PQ: 0 ANSI: 5
[ 6.404000] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 6.432000] sd 0:0:0:0: [sda] 312581808 512-byte logical blocks: (160 GB/149 GiB)
[ 6.444000] sd 0:0:0:0: [sda] Write Protect is off
[ 6.448000] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 6.448000] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 6.668000] sda: sda1
[ 6.676000] sd 0:0:0:0: [sda] Attached SCSI disk
[ 6.688000] Freeing unused kernel memory: 2048K
[ 6.692000] This architecture does not have kernel memory protection.
[ 6.696000] Run /init as init process
[ 37.036000] EXT4-fs (sda1): mounting ext3 file system using the ext4 subsystem
[ 38.184000] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null)
[ 65.600000] RTL8211B Gigabit Ethernet r8169-30:00: attached PHY driver [RTL8211B Gigabit Ethernet] (mii_bus:phy_addr=r8169-30:00, irq=IGNORE)
[ 68.280000] r8169 0000:00:06.0 eth0: Link is Up - 1Gbps/Full - flow control rx/tx
[ 76.244000] Adding 524256k swap on /SWAP. Priority:-2 extents:13 across:145760016k
-----
A.
