Hi- My XPS 13 9350 laptop has an nvme drive. It has on-chip ahci capability, but the M.2 port isn't using it due to the aforementioned nvme drive using the same signal pins. It is very unhappy: [ 0.230455] libata version 3.00 loaded. [ 1.039360] ahci 0000:00:17.0: version 3.0 [ 1.039386] ahci 0000:00:17.0: forcing PORTS_IMPL to 0xff [ 1.539388] ahci 0000:00:17.0: failed to stop engine (-5) [ 2.039392] ahci 0000:00:17.0: failed to stop engine (-5) [ 2.539402] ahci 0000:00:17.0: failed to stop engine (-5) [ 2.539437] ahci 0000:00:17.0: AHCI 0001.0301 32 slots 8 ports 6 Gbps 0xff impl SATA mode [ 2.539440] ahci 0000:00:17.0: flags: 64bit ncq pm led clo only pio slum part deso sadm sds apst [ 2.540855] scsi host0: ahci [ 2.541455] scsi host1: ahci [ 2.541972] scsi host2: ahci [ 2.542504] scsi host3: ahci [ 2.543027] scsi host4: ahci [ 2.543550] scsi host5: ahci [ 2.544035] scsi host6: ahci [ 2.544565] scsi host7: ahci [ 2.544641] ata1: SATA max UDMA/133 abar m2048@0xdc333000 port 0xdc333100 irq 122 [ 2.544645] ata2: SATA max UDMA/133 abar m2048@0xdc333000 port 0xdc333180 irq 122 [ 2.544648] ata3: SATA max UDMA/133 abar m2048@0xdc333000 port 0xdc333200 irq 122 [ 2.544652] ata4: SATA max UDMA/133 abar m2048@0xdc333000 port 0xdc333280 irq 122 [ 2.544656] ata5: SATA max UDMA/133 abar m2048@0xdc333000 port 0xdc333300 irq 122 [ 2.544659] ata6: SATA max UDMA/133 abar m2048@0xdc333000 port 0xdc333380 irq 122 [ 2.544662] ata7: SATA max UDMA/133 abar m2048@0xdc333000 port 0xdc333400 irq 122 [ 2.544666] ata8: SATA max UDMA/133 abar m2048@0xdc333000 port 0xdc333480 irq 122 [ 3.552450] ata8: failed to resume link (SControl 0) [ 3.552471] ata8: SATA link down (SStatus 0 SControl 0) [ 3.552491] ata7: failed to resume link (SControl 0) [ 3.552508] ata7: SATA link down (SStatus 0 SControl 0) [ 3.552528] ata6: failed to resume link (SControl 0) [ 3.552548] ata6: SATA link down (SStatus 0 SControl 0) [ 3.552567] ata5: failed to resume link (SControl 0) [ 3.552585] ata5: SATA link down (SStatus 0 SControl 0) [ 3.552602] ata4: failed to resume link (SControl 0) [ 3.552616] ata4: SATA link down (SStatus 0 SControl 0) [ 4.051472] ata2: failed to resume link (SControl FFFFFFFF) [ 4.051493] ata2: SATA link down (SStatus FFFFFFFF SControl FFFFFFFF) [ 4.052349] ata1: failed to resume link (SControl FFFFFFFF) [ 4.052370] ata1: SATA link down (SStatus FFFFFFFF SControl FFFFFFFF) [ 4.052394] ata3: failed to resume link (SControl FFFFFFFF) [ 4.052414] ata3: SATA link down (SStatus FFFFFFFF SControl FFFFFFFF) [ 4.556598] Write protecting the kernel read-only data: 14336k [ 12.410784] EXT4-fs (dm-1): mounted filesystem with ordered data mode. Opts: (null) [ 13.471239] EXT4-fs (nvme0n1p2): mounted filesystem with ordered data mode. Opts: (null) It has Alpine Ridge, but I don't think there's such thing as SATA over USB Type C. I'd guess that that what's going on is that the ahci controller genuinely has zero ports enabled and the workaround for port_map == 0 is firing incorrectly. This is Linux 4.4. --Andy -- To unsubscribe from this list: send the line "unsubscribe linux-ide" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
