Re: linux: sata_nv: adma support

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Sun, Aug 2, 2015 at 3:08 AM, Pali Rohár <pali.rohar@xxxxxxxxx> wrote:
> On Sunday 02 August 2015 03:45:32 Robert Hancock wrote:
>> On Sat, Aug 1, 2015 at 2:09 PM, Pali Rohár <pali.rohar@xxxxxxxxx>
>> wrote:
>> > On Thursday 25 December 2014 07:22:13 Robert Hancock wrote:
>> >> On Tue, Dec 23, 2014 at 1:51 PM, Pali Rohár <pali.rohar@xxxxxxxxx>
>> >>
>> >> wrote:
>> >> > Hello,
>> >> >
>> >> > I have nvidia nforce4 motherboard with nvidia sata controller:
>> >> >
>> >> > 00:07.0 IDE interface [0101]: NVIDIA Corporation CK804 Serial
>> >> > ATA Controller [10de:0054] (rev f3)
>> >> > 00:08.0 IDE interface [0101]: NVIDIA Corporation CK804 Serial
>> >> > ATA Controller [10de:0055] (rev f3)
>> >> >
>> >> > I manually enabled adma mode (which is disabled by default) by
>> >> > adding sata_nv.adma=1 to grub cmdline. In git history I found
>> >> > that enabling adma mode includes NCQ support and reduced CPU
>> >> > overhead. It looks like adma mode is working, but at every boot
>> >> > I see one same error message in dmesg:
>> >> >
>> >> > [   16.823514] ata1.00: exception Emask 0x1 SAct 0x0 SErr 0x0
>> >> > action 0x0
>> >> > [   16.823520] ata1.00: CPB resp_flags 0x11: , CMD error
>> >> > [   16.823524] ata1.00: failed command: SET FEATURES
>> >> > [   16.823530] ata1.00: cmd ef/05:fe:00:00:00/00:00:00:00:00/40
>> >> > tag 16
>> >> > [   16.823530]          res 51/04:fe:00:00:00/00:00:00:00:00/40
>> >> > Emask 0x1 (device error)
>> >> > [   16.823533] ata1.00: status: { DRDY ERR }
>> >> > [   16.823535] ata1.00: error: { ABRT }
>> >> >
>> >> > When adma is disabled then this error message is not generated.
>> >>
>> >> It looks like something is trying to issue a command to disable
>> >> APM power management on the drive, and the command fails (likely
>> >> because it doesn't support that command). I'm not sure where that
>> >> would be coming from - I'm pretty sure the kernel doesn't issue
>> >> that command itself. Something that's part of your distro
>> >> perhaps?
>> >>
>> >> I don't know why it would only be failing in ADMA mode either,
>> >> though depending on where the command is coming from, maybe it's
>> >> not being issued otherwise for some reason?
>> >>
>> >> > What does that error message means? It is critical? What is that
>> >> > command SET FEATURES doing? Are there any problems with adma
>> >> > mode on nforce4 motherboards? Because I did not see any
>> >> > problems (except that one error message).
>> >> >
>> >> > --
>> >> > Pali Rohár
>> >> > pali.rohar@xxxxxxxxx
>> >
>> > Hello,
>> >
>> > now after long time I did more investigation and that error is
>> > reported for every connected HDD. I identified that it comes from
>> > udev script
>> >
>> >  /lib/udev/rules.d/85-hdparm.rules
>> >
>> > which just call script /lib/udev/hdparm for every one connected
>> > HDD.
>> >
>> > Script /lib/udev/hdparm just call:
>> >  /sbin/hdparm -B254 $DRIVE
>> >
>> > And that -B254 cause above error message in dmesg log. Output from
>> >
>> > hdparm is:
>> >  /dev/sda:
>> >   setting Advanced Power Management level to 0xfe (254)
>> >   APM_level      = not supported
>> >
>> > Any idea why in ADMA mode it cause above error (APM unsupported)
>> > and in non ADMA mode it is working fine? Maybe APM ATA commands
>> > should not be sent via ADMA?
>> >
>> > Here is another output:
>> >  $ sudo hdparm -I /dev/sda | grep -i power
>> >
>> >             *    Power Management feature set
>> >
>> >                  Power-Up In Standby feature set
>> >
>> >             *    SET_FEATURES required to spinup after power up
>> >             *    Host-initiated interface power management
>>
>> The "set features" command is a non-data command so based on our
>> current knowledge, it should work in ADMA mode. However, these NVIDIA
>> SATAs are black boxes, and rather buggy ones at that, so it's
>> possible there's an unknown issue there.
>>
>
> Maybe I should note that hdparm -I did not generated any error message.
> I post is here because it show "Power Management feature set" is
> supported by HDD. This indicate that HDD supports -B (APM) command,
> right?

As far as I know, yes.

>
>> The easiest way to test that would be to take out the condition check
>> for qc->tf.protocol == ATA_PROT_NODATA in nv_adma_use_reg_mode in
>> drivers/ata/sata_nv.c. That would force it to disable ADMA for all
>> non-data commands.
>>
>
> Ok, as now I have just SSH access to that machine, I will do kernel
> patching later (when I have physical access to it).
>
>> I really don't know why Ubuntu is disabling APM on all drives on
>> bootup however. Especially for laptops, that seems like a silly thing
>> to do explicitly. Sounds like one of the silly things Ubuntu is known
>> to do without consulting people.
>
> Looks like this comes from upstream udev/systemd project :-( Anyway, for
> laptops on battery ubuntu has another set of scripts which turn on APM
> (based on connected/disconnected AC adapter).

There's no such scripts in Fedora, so either they removed it, or it's
something that either Debian or Ubuntu has added in.

>
> That udev script which turn off APM is called when any disk is attached
> to system (so at boot time it is called for every one disk).
>
> Now I just masked that udev script and it is no longer called...
>
> Anyway if I call hdparm -B /dev/sda I get output:
>
> APM_level      = not supported
>
> And important is that there is no error message in dmesg. I get it only
> if I call hdparm -B with parameter (set option). But APM should be
> supported, right?

Does the get command work without ADMA enabled?
--
To unsubscribe from this list: send the line "unsubscribe linux-ide" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html



[Index of Archives]     [Linux Filesystems]     [Linux SCSI]     [Linux RAID]     [Git]     [Kernel Newbies]     [Linux Newbie]     [Security]     [Netfilter]     [Bugtraq]     [Yosemite News]     [MIPS Linux]     [ARM Linux]     [Linux Security]     [Samba]     [Device Mapper]

  Powered by Linux