On Wednesday 09 July 2014 03:06 PM, Srinivas Kandagatla wrote:
> Hi Kishon,
>
> Could you please consider this for v3.17?
>
sure.. please send the dt binding docs along with this patch.
Cheers
Kishon
>
> Thanks,
> srini
>
> On 23/06/14 19:00, Srinivas Kandagatla wrote:
>> Add a PHY driver for uses with AHCI based SATA controller driver on the
>> APQ8064 family of SoCs.
>>
>> This patch is a forward port plus separating PHY code of SATA driver
>> from Qualcomm's v3.4 andriod kernel.
>>
>> Tested on IFC6410 board.
>>
>> CC: Sujit Reddy Thumma <sthumma@xxxxxxxxxxxxxx>
>> Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@xxxxxxxxxx>
>> ---
>> drivers/phy/Kconfig | 7 +
>> drivers/phy/Makefile | 1 +
>> drivers/phy/phy-qcom-apq8064-sata.c | 358 ++++++++++++++++++++++++++++++++++++
>> 3 files changed, 366 insertions(+)
>> create mode 100644 drivers/phy/phy-qcom-apq8064-sata.c
>>
>> diff --git a/drivers/phy/Kconfig b/drivers/phy/Kconfig
>> index b7b6bce..39083c7 100644
>> --- a/drivers/phy/Kconfig
>> +++ b/drivers/phy/Kconfig
>> @@ -178,6 +178,13 @@ config PHY_XGENE
>> help
>> This option enables support for APM X-Gene SoC multi-purpose PHY.
>>
>> +config PHY_QCOM_APQ8064_SATA
>> + tristate "Qualcomm APQ8064 SATA SerDes/PHY driver"
>> + depends on ARCH_QCOM
>> + depends on HAS_IOMEM
>> + depends on OF
>> + select GENERIC_PHY
>> +
>> config PHY_QCOM_IPQ806X_SATA
>> tristate "Qualcomm IPQ806x SATA SerDes/PHY driver"
>> depends on ARCH_QCOM
>> diff --git a/drivers/phy/Makefile b/drivers/phy/Makefile
>> index d950317..8782088 100644
>> --- a/drivers/phy/Makefile
>> +++ b/drivers/phy/Makefile
>> @@ -20,4 +20,5 @@ phy-exynos-usb2-$(CONFIG_PHY_EXYNOS4X12_USB2) +=
>> phy-exynos4x12-usb2.o
>> phy-exynos-usb2-$(CONFIG_PHY_EXYNOS5250_USB2) += phy-exynos5250-usb2.o
>> obj-$(CONFIG_PHY_EXYNOS5_USBDRD) += phy-exynos5-usbdrd.o
>> obj-$(CONFIG_PHY_XGENE) += phy-xgene.o
>> +obj-$(CONFIG_PHY_QCOM_APQ8064_SATA) += phy-qcom-apq8064-sata.o
>> obj-$(CONFIG_PHY_QCOM_IPQ806X_SATA) += phy-qcom-ipq806x-sata.o
>> diff --git a/drivers/phy/phy-qcom-apq8064-sata.c
>> b/drivers/phy/phy-qcom-apq8064-sata.c
>> new file mode 100644
>> index 0000000..e9e59e2
>> --- /dev/null
>> +++ b/drivers/phy/phy-qcom-apq8064-sata.c
>> @@ -0,0 +1,358 @@
>> +/*
>> + * Copyright (c) 2014, The Linux Foundation. All rights reserved.
>> + *
>> + * This program is free software; you can redistribute it and/or modify
>> + * it under the terms of the GNU General Public License version 2 and
>> + * only version 2 as published by the Free Software Foundation.
>> + *
>> + * This program is distributed in the hope that it will be useful,
>> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
>> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
>> + * GNU General Public License for more details.
>> + */
>> +
>> +#include <linux/io.h>
>> +#include <linux/kernel.h>
>> +#include <linux/module.h>
>> +#include <linux/of.h>
>> +#include <linux/time.h>
>> +#include <linux/delay.h>
>> +#include <linux/clk.h>
>> +#include <linux/slab.h>
>> +#include <linux/platform_device.h>
>> +#include <linux/phy/phy.h>
>> +
>> +/* PHY registers */
>> +#define UNIPHY_PLL_REFCLK_CFG 0x000
>> +#define UNIPHY_PLL_POSTDIV1_CFG 0x004
>> +#define UNIPHY_PLL_CHGPUMP_CFG 0x008
>> +#define UNIPHY_PLL_VCOLPF_CFG 0x00C
>> +#define UNIPHY_PLL_VREG_CFG 0x010
>> +#define UNIPHY_PLL_PWRGEN_CFG 0x014
>> +#define UNIPHY_PLL_DMUX_CFG 0x018
>> +#define UNIPHY_PLL_AMUX_CFG 0x01C
>> +#define UNIPHY_PLL_GLB_CFG 0x020
>> +#define UNIPHY_PLL_POSTDIV2_CFG 0x024
>> +#define UNIPHY_PLL_POSTDIV3_CFG 0x028
>> +#define UNIPHY_PLL_LPFR_CFG 0x02C
>> +#define UNIPHY_PLL_LPFC1_CFG 0x030
>> +#define UNIPHY_PLL_LPFC2_CFG 0x034
>> +#define UNIPHY_PLL_SDM_CFG0 0x038
>> +#define UNIPHY_PLL_SDM_CFG1 0x03C
>> +#define UNIPHY_PLL_SDM_CFG2 0x040
>> +#define UNIPHY_PLL_SDM_CFG3 0x044
>> +#define UNIPHY_PLL_SDM_CFG4 0x048
>> +#define UNIPHY_PLL_SSC_CFG0 0x04C
>> +#define UNIPHY_PLL_SSC_CFG1 0x050
>> +#define UNIPHY_PLL_SSC_CFG2 0x054
>> +#define UNIPHY_PLL_SSC_CFG3 0x058
>> +#define UNIPHY_PLL_LKDET_CFG0 0x05C
>> +#define UNIPHY_PLL_LKDET_CFG1 0x060
>> +#define UNIPHY_PLL_LKDET_CFG2 0x064
>> +#define UNIPHY_PLL_TEST_CFG 0x068
>> +#define UNIPHY_PLL_CAL_CFG0 0x06C
>> +#define UNIPHY_PLL_CAL_CFG1 0x070
>> +#define UNIPHY_PLL_CAL_CFG2 0x074
>> +#define UNIPHY_PLL_CAL_CFG3 0x078
>> +#define UNIPHY_PLL_CAL_CFG4 0x07C
>> +#define UNIPHY_PLL_CAL_CFG5 0x080
>> +#define UNIPHY_PLL_CAL_CFG6 0x084
>> +#define UNIPHY_PLL_CAL_CFG7 0x088
>> +#define UNIPHY_PLL_CAL_CFG8 0x08C
>> +#define UNIPHY_PLL_CAL_CFG9 0x090
>> +#define UNIPHY_PLL_CAL_CFG10 0x094
>> +#define UNIPHY_PLL_CAL_CFG11 0x098
>> +#define UNIPHY_PLL_EFUSE_CFG 0x09C
>> +#define UNIPHY_PLL_DEBUG_BUS_SEL 0x0A0
>> +#define UNIPHY_PLL_CTRL_42 0x0A4
>> +#define UNIPHY_PLL_CTRL_43 0x0A8
>> +#define UNIPHY_PLL_CTRL_44 0x0AC
>> +#define UNIPHY_PLL_CTRL_45 0x0B0
>> +#define UNIPHY_PLL_CTRL_46 0x0B4
>> +#define UNIPHY_PLL_CTRL_47 0x0B8
>> +#define UNIPHY_PLL_CTRL_48 0x0BC
>> +#define UNIPHY_PLL_STATUS 0x0C0
>> +#define UNIPHY_PLL_DEBUG_BUS0 0x0C4
>> +#define UNIPHY_PLL_DEBUG_BUS1 0x0C8
>> +#define UNIPHY_PLL_DEBUG_BUS2 0x0CC
>> +#define UNIPHY_PLL_DEBUG_BUS3 0x0D0
>> +#define UNIPHY_PLL_CTRL_54 0x0D4
>> +
>> +#define SATA_PHY_SER_CTRL 0x100
>> +#define SATA_PHY_TX_DRIV_CTRL0 0x104
>> +#define SATA_PHY_TX_DRIV_CTRL1 0x108
>> +#define SATA_PHY_TX_DRIV_CTRL2 0x10C
>> +#define SATA_PHY_TX_DRIV_CTRL3 0x110
>> +#define SATA_PHY_TX_IMCAL0 0x11C
>> +#define SATA_PHY_TX_IMCAL1 0x120
>> +#define SATA_PHY_TX_IMCAL2 0x124
>> +#define SATA_PHY_RX_IMCAL0 0x128
>> +#define SATA_PHY_RX_IMCAL1 0x12C
>> +#define SATA_PHY_RX_IMCAL2 0x130
>> +#define SATA_PHY_RX_TERM 0x134
>> +#define SATA_PHY_EQUAL 0x13C
>> +#define SATA_PHY_OOB_TERM 0x144
>> +#define SATA_PHY_CDR_CTRL0 0x148
>> +#define SATA_PHY_CDR_CTRL1 0x14C
>> +#define SATA_PHY_CDR_CTRL2 0x150
>> +#define SATA_PHY_CDR_CTRL3 0x154
>> +#define SATA_PHY_CDR_CTRL4 0x158
>> +#define SATA_PHY_FA_LOAD0 0x15C
>> +#define SATA_PHY_FA_LOAD1 0x160
>> +#define SATA_PHY_PI_CTRL0 0x168
>> +#define SATA_PHY_PI_CTRL1 0x16C
>> +#define SATA_PHY_AD_TPA_CTRL 0x178
>> +#define SATA_PHY_REFCLK_CTRL 0x17C
>> +#define SATA_PHY_POW_DWN_CTRL0 0x180
>> +#define SATA_PHY_POW_DWN_CTRL1 0x184
>> +#define SATA_PHY_TX_DATA_CTRL 0x188
>> +#define SATA_PHY_BIST_GEN0 0x18C
>> +#define SATA_PHY_BIST_GEN1 0x190
>> +#define SATA_PHY_BIST_GEN2 0x194
>> +#define SATA_PHY_BIST_GEN3 0x198
>> +#define SATA_PHY_LBK_CTRL 0x19C
>> +#define SATA_PHY_TEST_DEBUG_CTRL 0x1A0
>> +#define SATA_PHY_ALIGNP 0x1A4
>> +#define SATA_PHY_PRBS_CFG0 0x1A8
>> +#define SATA_PHY_PRBS_CFG1 0x1AC
>> +#define SATA_PHY_PRBS_CFG2 0x1B0
>> +#define SATA_PHY_PRBS_CFG3 0x1B4
>> +#define SATA_PHY_CHAN_COMP_CHK_CNT 0x1B8
>> +#define SATA_PHY_RESET_CTRL 0x1BC
>> +#define SATA_PHY_RX_CLR 0x1C0
>> +#define SATA_PHY_RX_EBUF_CTRL 0x1C4
>> +#define SATA_PHY_ID0 0x1C8
>> +#define SATA_PHY_ID1 0x1CC
>> +#define SATA_PHY_ID2 0x1D0
>> +#define SATA_PHY_ID3 0x1D4
>> +#define SATA_PHY_RX_CHK_ERR_CNT0 0x1D8
>> +#define SATA_PHY_RX_CHK_ERR_CNT1 0x1DC
>> +#define SATA_PHY_RX_CHK_STAT 0x1E0
>> +#define SATA_PHY_TX_IMCAL_STAT 0x1E4
>> +#define SATA_PHY_RX_IMCAL_STAT 0x1E8
>> +#define SATA_PHY_RX_EBUF_STAT 0x1EC
>> +#define SATA_PHY_DEBUG_BUS_STAT0 0x1F0
>> +#define SATA_PHY_DEBUG_BUS_STAT1 0x1F4
>> +#define SATA_PHY_DEBUG_BUS_STAT2 0x1F8
>> +#define SATA_PHY_DEBUG_BUS_STAT3 0x1FC
>> +
>> +#define UNIPHY_PLL_LOCK BIT(0)
>> +#define SATA_PHY_TX_CAL BIT(0)
>> +#define SATA_PHY_RX_CAL BIT(0)
>> +
>> +/* default timeout set to 1 sec */
>> +#define TIMEOUT_MS 10000
>> +
>> +struct qcom_apq8064_sata_phy {
>> + void __iomem *mmio;
>> + struct clk *cfg_clk;
>> + struct device *dev;
>> +};
>> +
>> +/* Helper function to do poll and timeout */
>> +static int read_poll_timeout(void __iomem *addr, u32 mask)
>> +{
>> + unsigned long timeout = jiffies + msecs_to_jiffies(TIMEOUT_MS);
>> + u32 val;
>> +
>> + do {
>> + cpu_relax();
>> + val = readl_relaxed(addr);
>> + if (val & mask)
>> + break;
>> + } while (!time_after(jiffies, timeout));
>> +
>> + return (val & mask) ? 0 : -ETIMEDOUT;
>> +}
>> +
>> +static int qcom_apq8064_sata_phy_init(struct phy *generic_phy)
>> +{
>> + struct qcom_apq8064_sata_phy *phy = phy_get_drvdata(generic_phy);
>> + void __iomem *base = phy->mmio;
>> + int ret = 0;
>> +
>> + /* SATA phy initialization */
>> + writel_relaxed(0x01, base + SATA_PHY_SER_CTRL);
>> + writel_relaxed(0xB1, base + SATA_PHY_POW_DWN_CTRL0);
>> + /* Make sure the power down happens before power up */
>> + mb();
>> + usleep_range(10, 60);
>> +
>> + writel_relaxed(0x01, base + SATA_PHY_POW_DWN_CTRL0);
>> + writel_relaxed(0x3E, base + SATA_PHY_POW_DWN_CTRL1);
>> + writel_relaxed(0x01, base + SATA_PHY_RX_IMCAL0);
>> + writel_relaxed(0x01, base + SATA_PHY_TX_IMCAL0);
>> + writel_relaxed(0x02, base + SATA_PHY_TX_IMCAL2);
>> +
>> + /* Write UNIPHYPLL registers to configure PLL */
>> + writel_relaxed(0x04, base + UNIPHY_PLL_REFCLK_CFG);
>> + writel_relaxed(0x00, base + UNIPHY_PLL_PWRGEN_CFG);
>> +
>> + writel_relaxed(0x0A, base + UNIPHY_PLL_CAL_CFG0);
>> + writel_relaxed(0xF3, base + UNIPHY_PLL_CAL_CFG8);
>> + writel_relaxed(0x01, base + UNIPHY_PLL_CAL_CFG9);
>> + writel_relaxed(0xED, base + UNIPHY_PLL_CAL_CFG10);
>> + writel_relaxed(0x02, base + UNIPHY_PLL_CAL_CFG11);
>> +
>> + writel_relaxed(0x36, base + UNIPHY_PLL_SDM_CFG0);
>> + writel_relaxed(0x0D, base + UNIPHY_PLL_SDM_CFG1);
>> + writel_relaxed(0xA3, base + UNIPHY_PLL_SDM_CFG2);
>> + writel_relaxed(0xF0, base + UNIPHY_PLL_SDM_CFG3);
>> + writel_relaxed(0x00, base + UNIPHY_PLL_SDM_CFG4);
>> +
>> + writel_relaxed(0x19, base + UNIPHY_PLL_SSC_CFG0);
>> + writel_relaxed(0xE1, base + UNIPHY_PLL_SSC_CFG1);
>> + writel_relaxed(0x00, base + UNIPHY_PLL_SSC_CFG2);
>> + writel_relaxed(0x11, base + UNIPHY_PLL_SSC_CFG3);
>> +
>> + writel_relaxed(0x04, base + UNIPHY_PLL_LKDET_CFG0);
>> + writel_relaxed(0xFF, base + UNIPHY_PLL_LKDET_CFG1);
>> +
>> + writel_relaxed(0x02, base + UNIPHY_PLL_GLB_CFG);
>> + /* make sure global config LDO power down happens before power up */
>> + mb();
>> +
>> + writel_relaxed(0x03, base + UNIPHY_PLL_GLB_CFG);
>> + writel_relaxed(0x05, base + UNIPHY_PLL_LKDET_CFG2);
>> +
>> + /* PLL Lock wait */
>> + ret = read_poll_timeout(base + UNIPHY_PLL_STATUS, UNIPHY_PLL_LOCK);
>> + if (ret) {
>> + dev_err(phy->dev, "poll timeout UNIPHY_PLL_STATUS\n");
>> + return ret;
>> + }
>> +
>> + /* TX Calibration */
>> + ret = read_poll_timeout(base + SATA_PHY_TX_IMCAL_STAT, SATA_PHY_TX_CAL);
>> + if (ret) {
>> + dev_err(phy->dev, "poll timeout SATA_PHY_TX_IMCAL_STAT\n");
>> + return ret;
>> + }
>> +
>> + /* RX Calibration */
>> + ret = read_poll_timeout(base + SATA_PHY_RX_IMCAL_STAT, SATA_PHY_RX_CAL);
>> + if (ret) {
>> + dev_err(phy->dev, "poll timeout SATA_PHY_RX_IMCAL_STAT\n");
>> + return ret;
>> + }
>> +
>> + /* SATA phy calibrated succesfully, power up to functional mode */
>> + writel_relaxed(0x3E, base + SATA_PHY_POW_DWN_CTRL1);
>> + writel_relaxed(0x01, base + SATA_PHY_RX_IMCAL0);
>> + writel_relaxed(0x01, base + SATA_PHY_TX_IMCAL0);
>> +
>> + writel_relaxed(0x00, base + SATA_PHY_POW_DWN_CTRL1);
>> + writel_relaxed(0x59, base + SATA_PHY_CDR_CTRL0);
>> + writel_relaxed(0x04, base + SATA_PHY_CDR_CTRL1);
>> + writel_relaxed(0x00, base + SATA_PHY_CDR_CTRL2);
>> + writel_relaxed(0x00, base + SATA_PHY_PI_CTRL0);
>> + writel_relaxed(0x00, base + SATA_PHY_CDR_CTRL3);
>> + writel_relaxed(0x01, base + SATA_PHY_POW_DWN_CTRL0);
>> +
>> + writel_relaxed(0x11, base + SATA_PHY_TX_DATA_CTRL);
>> + writel_relaxed(0x43, base + SATA_PHY_ALIGNP);
>> + writel_relaxed(0x04, base + SATA_PHY_OOB_TERM);
>> +
>> + writel_relaxed(0x01, base + SATA_PHY_EQUAL);
>> + writel_relaxed(0x09, base + SATA_PHY_TX_DRIV_CTRL0);
>> + writel_relaxed(0x09, base + SATA_PHY_TX_DRIV_CTRL1);
>> +
>> + return 0;
>> +}
>> +
>> +static int qcom_apq8064_sata_phy_exit(struct phy *generic_phy)
>> +{
>> + struct qcom_apq8064_sata_phy *phy = phy_get_drvdata(generic_phy);
>> + void __iomem *base = phy->mmio;
>> +
>> + /* Power down PHY */
>> + writel_relaxed(0xF8, base + SATA_PHY_POW_DWN_CTRL0);
>> + writel_relaxed(0xFE, base + SATA_PHY_POW_DWN_CTRL1);
>> +
>> + /* Power down PLL block */
>> + writel_relaxed(0x00, base + UNIPHY_PLL_GLB_CFG);
>> +
>> + return 0;
>> +}
>> +
>> +static struct phy_ops qcom_apq8064_sata_phy_ops = {
>> + .init = qcom_apq8064_sata_phy_init,
>> + .exit = qcom_apq8064_sata_phy_exit,
>> + .owner = THIS_MODULE,
>> +};
>> +
>> +static int qcom_apq8064_sata_phy_probe(struct platform_device *pdev)
>> +{
>> + struct qcom_apq8064_sata_phy *phy;
>> + struct device *dev = &pdev->dev;
>> + struct resource *res;
>> + struct phy_provider *phy_provider;
>> + struct phy *generic_phy;
>> + int ret;
>> +
>> + phy = devm_kzalloc(dev, sizeof(*phy), GFP_KERNEL);
>> + if (!phy)
>> + return -ENOMEM;
>> +
>> + res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
>> + phy->mmio = devm_ioremap_resource(dev, res);
>> + if (IS_ERR(phy->mmio))
>> + return PTR_ERR(phy->mmio);
>> +
>> + generic_phy = devm_phy_create(dev, &qcom_apq8064_sata_phy_ops, NULL);
>> + if (IS_ERR(generic_phy)) {
>> + dev_err(dev, "%s: failed to create phy\n", __func__);
>> + return PTR_ERR(generic_phy);
>> + }
>> +
>> + phy->dev = dev;
>> + phy_set_drvdata(generic_phy, phy);
>> +
>> + phy->cfg_clk = devm_clk_get(dev, "cfg");
>> + if (IS_ERR(phy->cfg_clk)) {
>> + dev_err(dev, "Failed to get sata cfg clock\n");
>> + return PTR_ERR(phy->cfg_clk);
>> + }
>> +
>> + ret = clk_prepare_enable(phy->cfg_clk);
>> + if (ret)
>> + return ret;
>> +
>> + phy_provider = devm_of_phy_provider_register(dev, of_phy_simple_xlate);
>> + if (IS_ERR(phy_provider)) {
>> + clk_disable_unprepare(phy->cfg_clk);
>> + dev_err(dev, "%s: failed to register phy\n", __func__);
>> + return PTR_ERR(phy_provider);
>> + }
>> +
>> + return 0;
>> +}
>> +
>> +static int qcom_apq8064_sata_phy_remove(struct platform_device *pdev)
>> +{
>> + struct qcom_apq8064_sata_phy *phy = platform_get_drvdata(pdev);
>> +
>> + clk_disable_unprepare(phy->cfg_clk);
>> +
>> + return 0;
>> +}
>> +
>> +static const struct of_device_id qcom_apq8064_sata_phy_of_match[] = {
>> + { .compatible = "qcom,apq8064-sata-phy" },
>> + { },
>> +};
>> +MODULE_DEVICE_TABLE(of, qcom_apq8064_sata_phy_of_match);
>> +
>> +static struct platform_driver qcom_apq8064_sata_phy_driver = {
>> + .probe = qcom_apq8064_sata_phy_probe,
>> + .remove = qcom_apq8064_sata_phy_remove,
>> + .driver = {
>> + .name = "qcom-apq8064-sata-phy",
>> + .owner = THIS_MODULE,
>> + .of_match_table = qcom_apq8064_sata_phy_of_match,
>> + }
>> +};
>> +module_platform_driver(qcom_apq8064_sata_phy_driver);
>> +
>> +MODULE_DESCRIPTION("QCOM apq8064 SATA PHY driver");
>> +MODULE_LICENSE("GPL v2");
>>
--
To unsubscribe from this list: send the line "unsubscribe linux-ide" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
