On 05/14/2014 08:12 PM, Arnd Bergmann wrote:
> On Wednesday 14 May 2014 19:57:46 Sebastian Hesselbarth wrote:
>> On 05/14/2014 06:57 PM, Antoine Ténart wrote:
>>> On Wed, May 14, 2014 at 06:11:24PM +0200, Arnd Bergmann wrote:
>>>> On Wednesday 14 May 2014 17:49:29 Antoine Ténart wrote:
>>>>> On Wed, May 14, 2014 at 05:31:24PM +0200, Arnd Bergmann wrote:
>>
>> From what I understand from the conversation, we have a single PHY
>> register set dealing with both SATA ports available on the SoC.
>> Also, from the name of the PHY bits we assume the PHY may be able
>> to work in different modes than just SATA. And we currently have
>> an AHCI-compatible SATA IP that supports up to two ports, with one
>> actually connected to a SATA plug on the DMP board.
>>
>> Now, thinking about the PHY binding and the (possible) multi-protocol
>> support, it can be possible that on BG2Q there is a generic 2-lane
>> LVDS PHY that can be configured to support SATA or PCIe. Both are
>> electrically and bit-level compatible, so they could be internally
>> wired-up with AHCI and PCIe controller.
>
> Sounds like a reasonable guess. We have other PHY drivers doing the
> same thing already.
Well, I based that on what I know about FPGA LVDS transceivers, so
I wasn't guessing out of the blue ;)
>> From a DT point-of-view, we need a way to (a) link each SATA or PCIe
>> port to the PHY, (b) specify the PHY lane to be used, and (c) specify
>> the protocol to be used on that lane. If I got it right, Arnd already
>> mentioned to use the phy-specifier to deal with it:
>>
>> e.g. phy = <&genphy 0 MODE_SATA> or phy = <&genphy 1 MODE_PCIE>
>
> Right.
>
>> Let's assume we have one dual-port SATA controller and one PCIe
>> controller with either x1 or x2 support. The only sane DT binding,
>> I can think of then would be:
>>
>> berlin2q.dtsi:
>>
>> genphy: lvds@ea00ff {
>> compatible = "marvell,berlin-lvds-phy";
>> reg = <0xea00ff 0x100>;
>> #phy-cells = <2>;
>> };
>>
>> sata: sata@ab00ff {
>> compatible = "ahci-platform";
>> reg = <0xab00ff 0x100>;
>>
>> sata0: sata-port@0 {
>> reg = <0>;
>> phy = <&genphy 0 MODE_SATA>;
>> status = "disabled";
>> };
>>
>> sata1: sata-port@1 {
>> reg = <1>;
>> phy = <&genphy 1 MODE_SATA>;
>> status = "disabled";
>> };
>> };
>>
>> pcie: pcie@ab01ff {
>> compatible = "marvell,berlin-pcie";
>> reg = <0xab01ff 0x100>;
>>
>> pcie0: pcie-port@0 {
>> reg = <0>;
>> /* set phy on a per-board basis */
>> /* PCIe x1 on Lane 0 : phy = <&genphy 0 MODE_PCIE>; */
>> /* PCIe x2 on Lane 0 and 1 : phy = <&genphy 0 MODE_PCIE>, <&genphy 1
>> MODE_PCIE>; */
>> status = "disabled";
>> };
>> };
>>
>> berlin2q-dmp.dts:
>>
>> &sata1 {
>> status = "okay";
>> };
>>
>> &pcie0 {
>> phy = <&genphy 1 MODE_PCIE>;
>> };
>>
>> berlin2q-foo.dts:
>>
>> &pcie0 {
>> phy = <&genphy 0 MODE_PCIE>, <&genphy 1 MODE_PCIE>;
>> };
>
> Exactly. I would also be fine with keeping the sub-nodes of the
> phy device as in v3 and using #phy-cells=<1> instead of #phy-cells.
> The result would be pretty much the same, it just depends on how
> closely connected the two logical phys are.
>
> IIRC for the ST microelectronics PHY we recently reviewed, the
> same PHY could be driving multiple SATA ports, or a single
> multi-lane PCIe. In that case, it makes more sense to have
> #phy-cells=<2>, like your example.
I guess the final call is up to Kishon, but I personally prefer
#phy-cells = <2>. It makes no functional difference though.
>> For the driver, Antoine then would have to squeeze all PHY register
>> mangling in phy-berlin2.c and see how to make ahci-platform aware of
>> individual port nodes (I haven't looked up if it already exists, sorry)
>> and announce only enabled port child nodes, right?
>
> I've been thinking some more about this aspect. I don't actually have
> a strong opinion on whether it's better to use the generic ahci-platform
> driver, or to keep the multi-phy support as a special variant for
> berlin. If we do the latter, it would however be good to define the
> binding in a way that lets us later merge things into the generic phy
> driver in case we get more of the same.
Hmm, IMHO multi-phy support is orthogonal to ahci-platform, isn't it?
ahci-platform needs to know about the phy property and calls some
helper that deals with the phy-specifier?
About a generic _phy_ driver, I am not so sure if berlin is the best
template right now ;)
So, my call would be:
- make ahci-platform aware of port sub-nodes and phy properties
- have a berlin specific PHY driver
Sebastian
--
To unsubscribe from this list: send the line "unsubscribe linux-ide" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
