The old IDE cmd64x checks the status of the CNTRL register to see if
the ports are enabled before probing them. pata_cmd64x doesn't do
this, which causes a HPMC on parisc when it tries to poke at the
secondary port because apparently the BAR isn't wired up (and a
non-responding piece of memory causes a HPMC).
Fix this by porting the CNTRL register port detection logic from IDE
cmd64x. In addition, following converns from Alan Cox, add a check to
see if a mobility electronics bridge is the immediate parent and forgo
the check if it is (prevents problems on hotplug controllers).
Signed-off-by: James Bottomley <James.Bottomley@xxxxxxx>
---
drivers/ata/pata_cmd64x.c | 42 ++++++++++++++++++++++++++++++++++++++----
include/linux/pci_ids.h | 2 ++
2 files changed, 40 insertions(+), 4 deletions(-)
diff --git a/drivers/ata/pata_cmd64x.c b/drivers/ata/pata_cmd64x.c
index 905ff76..7bafc16 100644
--- a/drivers/ata/pata_cmd64x.c
+++ b/drivers/ata/pata_cmd64x.c
@@ -41,6 +41,9 @@
enum {
CFR = 0x50,
CFR_INTR_CH0 = 0x04,
+ CNTRL = 0x51,
+ CNTRL_CH0 = 0x04,
+ CNTRL_CH1 = 0x08,
CMDTIM = 0x52,
ARTTIM0 = 0x53,
DRWTIM0 = 0x54,
@@ -328,9 +331,19 @@ static int cmd64x_init_one(struct pci_dev *pdev, const struct pci_device_id *id)
.port_ops = &cmd648_port_ops
}
};
- const struct ata_port_info *ppi[] = { &cmd_info[id->driver_data], NULL };
- u8 mrdmode;
+ const struct ata_port_info *ppi[] = {
+ &cmd_info[id->driver_data],
+ &cmd_info[id->driver_data],
+ NULL
+ };
+ u8 mrdmode, reg;
int rc;
+ struct pci_dev *bridge = pdev->bus->self;
+ /* mobility split bridges don't report enabled ports correctly */
+ int port_ok = !(bridge && bridge->vendor ==
+ PCI_VENDOR_ID_MOBILITY_ELECTRONICS);
+ /* all (with exceptions below) apart from 643 have CNTRL_CH0 bit */
+ int cntrl_ch0_ok = (id->driver_data != 0);
rc = pcim_enable_device(pdev);
if (rc)
@@ -341,11 +354,18 @@ static int cmd64x_init_one(struct pci_dev *pdev, const struct pci_device_id *id)
if (pdev->device == PCI_DEVICE_ID_CMD_646) {
/* Does UDMA work ? */
- if (pdev->revision > 4)
+ if (pdev->revision > 4) {
ppi[0] = &cmd_info[2];
+ ppi[1] = &cmd_info[2];
+ }
/* Early rev with other problems ? */
- else if (pdev->revision == 1)
+ else if (pdev->revision == 1) {
ppi[0] = &cmd_info[3];
+ ppi[1] = &cmd_info[3];
+ }
+ /* revs 1,2 have no CNTRL_CH0 */
+ if (pdev->revision < 3)
+ cntrl_ch0_ok = 0;
}
pci_write_config_byte(pdev, PCI_LATENCY_TIMER, 64);
@@ -354,6 +374,20 @@ static int cmd64x_init_one(struct pci_dev *pdev, const struct pci_device_id *id)
mrdmode |= 0x02; /* Memory read line enable */
pci_write_config_byte(pdev, MRDMODE, mrdmode);
+ /* check for enabled ports */
+ pci_read_config_byte(pdev, CNTRL, ®);
+ if (!port_ok)
+ dev_printk(KERN_NOTICE, &pdev->dev, "Mobility Bridge detected, ignoring CNTRL port enable/disable\n");
+ if (port_ok && cntrl_ch0_ok && !(reg & CNTRL_CH0)) {
+ dev_printk(KERN_NOTICE, &pdev->dev, "Primary port is disabled\n");
+ ppi[0] = &ata_dummy_port_info;
+
+ }
+ if (port_ok && !(reg & CNTRL_CH1)) {
+ dev_printk(KERN_NOTICE, &pdev->dev, "Secondary port is disabled\n");
+ ppi[1] = &ata_dummy_port_info;
+ }
+
/* Force PIO 0 here.. */
/* PPC specific fixup copied from old driver */
diff --git a/include/linux/pci_ids.h b/include/linux/pci_ids.h
index 4e2c915..7a0ac45 100644
--- a/include/linux/pci_ids.h
+++ b/include/linux/pci_ids.h
@@ -608,6 +608,8 @@
#define PCI_DEVICE_ID_MATROX_G550 0x2527
#define PCI_DEVICE_ID_MATROX_VIA 0x4536
+#define PCI_VENDOR_ID_MOBILITY_ELECTRONICS 0x14f2
+
#define PCI_VENDOR_ID_CT 0x102c
#define PCI_DEVICE_ID_CT_69000 0x00c0
#define PCI_DEVICE_ID_CT_65545 0x00d8
--
1.7.4.1
--
To unsubscribe from this list: send the line "unsubscribe linux-ide" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
