RE: [PATCH v6] libata: pata_samsung: Add Samsung PATA controller driver

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Sergei Shtylyov wrote:
> 
> Hello.

Hi ;-)
> 
> Kukjin Kim wrote:
> 
> > From: Abhilash Kesavan <a.kesavan@xxxxxxxxxxx>
> 
> > Adds support for the Samsung PATA controller. This driver is based on
the
> > Libata subsystem and references the earlier patches sent for IDE
subsystem.
> 
> > Signed-off-by: Abhilash Kesavan <a.kesavan@xxxxxxxxxxx>
> > Signed-off-by: Kukjin Kim <kgene.kim@xxxxxxxxxxx>
> > Cc: Ben Dooks <ben-linux@xxxxxxxxx>
> 
>     There's probably still a place for improvement... sorry that I dind't
> notice before. Other than that:
> 
Ok..will address comments from you and re-submit.

> Acked-by: Sergei Shtylyov <sshtylyov@xxxxxxxxxx>
> 
Will be added above your ack in updated patch.
If any problem, please let me know.

> [...]
> 
> > diff --git a/drivers/ata/pata_samsung_cf.c
b/drivers/ata/pata_samsung_cf.c
> > new file mode 100644
> > index 0000000..5718220
> > --- /dev/null
> > +++ b/drivers/ata/pata_samsung_cf.c
> > @@ -0,0 +1,727 @@
> [...]
> > +/*
> > + * pata_s3c_wait_after_reset - wait for devices to become ready after
reset
> > + */
> > +static int pata_s3c_wait_after_reset(struct ata_link *link,
> > +		unsigned int devmask, unsigned long deadline)
> > +{
> > +	struct ata_port *ap = link->ap;
> > +	struct ata_ioports *ioaddr = &ap->ioaddr;
> > +	unsigned int dev0 = devmask & (1 << 0);
> > +	unsigned int dev1 = devmask & (1 << 1);
> > +	int rc, ret = 0;
> > +
> > +	msleep(ATA_WAIT_AFTER_RESET);
> > +
> > +	/* always check readiness of the master device */
> > +	rc = ata_sff_wait_ready(link, deadline);
> > +	/* -ENODEV means the odd clown forgot the D7 pulldown resistor
> > +	 * and TF status is 0xff, bail out on it too.
> > +	 */
> > +	if (rc)
> > +		return rc;
> > +
> > +	/* if device 1 was found in ata_devchk, wait for register
> > +	 * access briefly, then wait for BSY to clear.
> > +	 */
> 
>     You don't call pata_s3c_devchk() for device 1, so in principle you can
> drop the following block:
> 
> > +	if (dev1) {
> > +		int i;
> > +
> > +		pata_s3c_dev_select(ap, 1);
> > +
> > +		/* Wait for register access.  Some ATAPI devices fail
> > +		 * to set nsect/lbal after reset, so don't waste too
> > +		 * much time on it.  We're gonna wait for !BSY anyway.
> > +		 */
> > +		for (i = 0; i < 2; i++) {
> > +			u8 nsect, lbal;
> > +
> > +			nsect = ata_inb(ap->host, ioaddr->nsect_addr);
> > +			lbal = ata_inb(ap->host, ioaddr->lbal_addr);
> > +			if ((nsect == 1) && (lbal == 1))
> > +				break;
> > +			msleep(50);	/* give drive a breather */
> > +		}
> > +
> > +		rc = ata_sff_wait_ready(link, deadline);
> > +		if (rc) {
> > +			if (rc != -ENODEV)
> > +				return rc;
> > +			ret = rc;
> > +		}
> > +	}
> > +
> > +	/* is all this really necessary? */
> > +	pata_s3c_dev_select(ap, 0);
> > +	if (dev1)
> > +		pata_s3c_dev_select(ap, 1);
> 
>     This too...
> 
> > +	if (dev0)
> > +		pata_s3c_dev_select(ap, 0);
> > +
> > +	return ret;
> > +}
> > +
> [...]
> > +static int pata_s3c_resume(struct device *dev)
> > +{
> > +	struct platform_device *pdev = to_platform_device(dev);
> > +	struct ata_host *host = platform_get_drvdata(pdev);
> > +	struct s3c_ide_platdata *pdata = pdev->dev.platform_data;
> > +	struct s3c_ide_info *info;
> > +
> > +	info = host->private_data;
> 
>     Could be initializer...
> 
> MBR, Sergei


Thanks.

Best regards,
Kgene.
--
Kukjin Kim <kgene.kim@xxxxxxxxxxx>, Senior Engineer,
SW Solution Development Team, Samsung Electronics Co., Ltd.

--
To unsubscribe from this list: send the line "unsubscribe linux-ide" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html


[Index of Archives]     [Linux Filesystems]     [Linux SCSI]     [Linux RAID]     [Git]     [Kernel Newbies]     [Linux Newbie]     [Security]     [Netfilter]     [Bugtraq]     [Yosemite News]     [MIPS Linux]     [ARM Linux]     [Linux Security]     [Samba]     [Device Mapper]

  Powered by Linux