IDE mode of MCP89 on MBP 7,1 doesn't set DMA enable bits in the BMDMA
status register. Make the following changes to work around the problem.
* Instead of using hard coded 1 in id->driver_data as class code
match, use ATA_GEN_CLASS_MATCH and carry the matched id in
host->private_data.
* Instead of matching PCI_VENDOR_ID_CENATEK, use ATA_GEN_FORCE_DMA
flag in id instead.
* Add ATA_GEN_FORCE_DMA to the id entry of MBP 7,1.
Signed-off-by: Tejun Heo <tj@xxxxxxxxxx>
Cc: Peer Chen <pchen@xxxxxxxxxx>
Cc: stable@xxxxxxxxxx
Reported-by: Anders Østhus <grapz666@xxxxxxxxx>
Reported-by: Andreas Graf <andreas_graf@xxxxxxxxx>
Reported-by: Benoit Gschwind <gschwind@xxxxxxxxxxx>
Reported-by: Damien Cassou <damien.cassou@xxxxxxxxx>
Reported-by: tixetsal@xxxxxxxx
---
drivers/ata/ata_generic.c | 26 +++++++++++++++++++-------
1 file changed, 19 insertions(+), 7 deletions(-)
Index: ata/drivers/ata/ata_generic.c
===================================================================
--- ata.orig/drivers/ata/ata_generic.c
+++ ata/drivers/ata/ata_generic.c
@@ -32,6 +32,11 @@
* A generic parallel ATA driver using libata
*/
+enum {
+ ATA_GEN_CLASS_MATCH = (1 << 0),
+ ATA_GEN_FORCE_DMA = (1 << 1),
+};
+
/**
* generic_set_mode - mode setting
* @link: link to set up
@@ -46,13 +51,17 @@
static int generic_set_mode(struct ata_link *link, struct ata_device **unused)
{
struct ata_port *ap = link->ap;
+ const struct pci_device_id *id = ap->host->private_data;
int dma_enabled = 0;
struct ata_device *dev;
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
- /* Bits 5 and 6 indicate if DMA is active on master/slave */
- if (ap->ioaddr.bmdma_addr)
+ if (id->driver_data & ATA_GEN_FORCE_DMA) {
+ dma_enabled = 0xff;
+ } else if (ap->ioaddr.bmdma_addr) {
+ /* Bits 5 and 6 indicate if DMA is active on master/slave */
dma_enabled = ioread8(ap->ioaddr.bmdma_addr + ATA_DMA_STATUS);
+ }
if (pdev->vendor == PCI_VENDOR_ID_CENATEK)
dma_enabled = 0xFF;
@@ -126,7 +135,7 @@ static int ata_generic_init_one(struct p
const struct ata_port_info *ppi[] = { &info, NULL };
/* Don't use the generic entry unless instructed to do so */
- if (id->driver_data == 1 && all_generic_ide == 0)
+ if ((id->driver_data & ATA_GEN_CLASS_MATCH) && all_generic_ide == 0)
return -ENODEV;
/* Devices that need care */
@@ -155,7 +164,7 @@ static int ata_generic_init_one(struct p
return rc;
pcim_pin_device(dev);
}
- return ata_pci_bmdma_init_one(dev, ppi, &generic_sht, NULL, 0);
+ return ata_pci_bmdma_init_one(dev, ppi, &generic_sht, (void *)id, 0);
}
static struct pci_device_id ata_generic[] = {
@@ -167,13 +176,15 @@ static struct pci_device_id ata_generic[
{ PCI_DEVICE(PCI_VENDOR_ID_HINT, PCI_DEVICE_ID_HINT_VXPROII_IDE), },
{ PCI_DEVICE(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_82C561), },
{ PCI_DEVICE(PCI_VENDOR_ID_OPTI, PCI_DEVICE_ID_OPTI_82C558), },
- { PCI_DEVICE(PCI_VENDOR_ID_CENATEK,PCI_DEVICE_ID_CENATEK_IDE), },
+ { PCI_DEVICE(PCI_VENDOR_ID_CENATEK,PCI_DEVICE_ID_CENATEK_IDE),
+ .driver_data = ATA_GEN_FORCE_DMA },
/*
* For some reason, MCP89 on MacBook 7,1 doesn't work with
* ahci, use ata_generic instead.
*/
{ PCI_VENDOR_ID_NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE_MCP89_SATA,
- PCI_VENDOR_ID_APPLE, 0xcb89, },
+ PCI_VENDOR_ID_APPLE, 0xcb89,
+ .driver_data = ATA_GEN_FORCE_DMA },
#if !defined(CONFIG_PATA_TOSHIBA) && !defined(CONFIG_PATA_TOSHIBA_MODULE)
{ PCI_DEVICE(PCI_VENDOR_ID_TOSHIBA,PCI_DEVICE_ID_TOSHIBA_PICCOLO_1), },
{ PCI_DEVICE(PCI_VENDOR_ID_TOSHIBA,PCI_DEVICE_ID_TOSHIBA_PICCOLO_2), },
@@ -181,7 +192,8 @@ static struct pci_device_id ata_generic[
{ PCI_DEVICE(PCI_VENDOR_ID_TOSHIBA,PCI_DEVICE_ID_TOSHIBA_PICCOLO_5), },
#endif
/* Must come last. If you add entries adjust this table appropriately */
- { PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID, PCI_CLASS_STORAGE_IDE << 8, 0xFFFFFF00UL, 1},
+ { PCI_DEVICE_CLASS(PCI_CLASS_STORAGE_IDE << 8, 0xFFFFFF00UL),
+ .driver_data = ATA_GEN_CLASS_MATCH },
{ 0, },
};
--
To unsubscribe from this list: send the line "unsubscribe linux-ide" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
