(ccing linux-ide)
Tejun, another one of these reset issues?
Konstantin Kletschke wrote:
Hello!
I found to references regarding this problem in this list. Many Maxwell
reported this and Tejo asked if his supposed fix helps out.
Another reference by Jeff suggests bisecting a git commit. Since I am
very unexperienced in the git stuff I hope it is okay to start another
initial mail about this to ask
1.) What I should try out on the code to trace this further down
2.) I would extend this problem on >2.6.25 version of kernel.
I have an "nForce3 250 chipset" on an Asrock K8Upgrade-NF3 Motherboard
00:00.0 Host bridge: nVidia Corporation nForce3 250Gb Host Bridge (rev a1)
00:01.0 ISA bridge: nVidia Corporation nForce3 250Gb LPC Bridge (rev a2)
00:01.1 SMBus: nVidia Corporation nForce 250Gb PCI System Management (rev a1)
00:02.0 USB Controller: nVidia Corporation CK8S USB Controller (rev a1)
00:02.1 USB Controller: nVidia Corporation CK8S USB Controller (rev a1)
00:02.2 USB Controller: nVidia Corporation nForce3 EHCI USB 2.0 Controller (rev a2)
00:05.0 Bridge: nVidia Corporation CK8S Ethernet Controller (rev a2)
00:06.0 Multimedia audio controller: nVidia Corporation nForce3 250Gb AC'97 Audio Controller (rev a1)
00:08.0 IDE interface: nVidia Corporation CK8S Parallel ATA Controller (v2.5) (rev a2)
00:0a.0 IDE interface: nVidia Corporation CK8S Serial ATA Controller (v2.5) (rev a2)
00:0b.0 PCI bridge: nVidia Corporation nForce3 250Gb AGP Host to PCI Bridge (rev a2)
00:0e.0 PCI bridge: nVidia Corporation nForce3 250Gb PCI-to-PCI Bridge (rev a2)
00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration
00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map
00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller
00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control
01:00.0 VGA compatible controller: nVidia Corporation NV34 [GeForce FX 5200] (rev a1)
02:06.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10)
While 2.6.25 works very fine I experienced this with 2.6.26_rc7 at first
(I skipped versions between). Cold Boot yields into the described error,
I sadly only have real screenshots of this:
http://ludenkalle.de/sata
After a reset the Kernel was not able to do anything useful with the
SATA interface anymore (this description is a bit vague, IIRC it stuck
immediately around "SATA Link down..."). Only powercycling helped out,
then it booted with SATA.
Now I have 2.6.27-rc3, same error but config netconsole enabled.
Normal Boot:
ata1: SATA link down (SStatus 0 SControl 300)
ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata2.00: ATA-7: SAMSUNG HD753LJ, 1AA01106, max UDMA7
ata2.00: 1465149168 sectors, multi 16: LBA48 NCQ (depth 0/32)
ata2.00: configured for UDMA/133
isa bounce pool size: 16 pages
scsi 1:0:0:0: Direct-Access ATA SAMSUNG HD753LJ 1AA0 PQ: 0 ANSI: 5
sd 1:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
sd 1:0:0:0: [sda] Write Protect is off
sd 1:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 1:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
sd 1:0:0:0: [sda] Write Protect is off
sd 1:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sda: sda1 sda2 sda3 sda4 < sda5 sda6 sda7 sda8 sda9 >
sd 1:0:0:0: [sda] Attached SCSI disk
PNP: No PS/2 controller found. Probing ports directly.
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
TCP cubic registered
NET: Registered protocol family 17
XFS mounting filesystem sda1
VFS: Mounted root (xfs filesystem) readonly.
Freeing unused kernel memory: 220k freed
Cold Boot:
ata1: SATA link down (SStatus 0 SControl 300)
ata2: link is slow to respond, please be patient (ready=0)
ata2: COMRESET failed (errno=-16)
ata2: link is slow to respond, please be patient (ready=0)
ata2: COMRESET failed (errno=-16)
ata2: link is slow to respond, please be patient (ready=0)
ata2: COMRESET failed (errno=-16)
ata2: limiting SATA link speed to 1.5 Gbps
ata2: COMRESET failed (errno=-16)
ata2: reset failed, giving up
PNP: No PS/2 controller found. Probing ports directly.
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
TCP cubic registered
NET: Registered protocol family 17
VFS: Cannot open root device "801" or unknown-block(8,1)
Please append a correct "root=" boot option; here are the available partitions:
Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(8,1)
Hmn, thats it. Where should I poke into?
Kind Regards, Konsti
--
To unsubscribe from this list: send the line "unsubscribe linux-ide" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
