I've got a system with a nvidia chipset running fedora 9 (2.6.25.11)
00:05.0 IDE interface: nVidia Corporation MCP55 SATA Controller (rev
a3) (prog-if 85 [Master SecO PriO])
Subsystem: Sun Microsystems Computer Corp. Unknown device 534d
Flags: bus master, 66MHz, fast devsel, latency 0, IRQ 21
I/O ports at 34c0 [size=8]
I/O ports at 34b4 [size=4]
I/O ports at 34b8 [size=8]
I/O ports at 34b0 [size=4]
I/O ports at 3490 [size=16]
Memory at d0006000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [44] Power Management version 2
Capabilities: [b0] Message Signalled Interrupts: Mask- 64bit+
Queue=0/2 Enable-
Capabilities: [cc] HyperTransport: MSI Mapping Enable+ Fixed+
Kernel driver in use: sata_nv
Kernel modules: ata_generic, sata_nv, pata_acpi
00:05.1 IDE interface: nVidia Corporation MCP55 SATA Controller (rev
a3) (prog-if 85 [Master SecO PriO])
Subsystem: Sun Microsystems Computer Corp. Unknown device 534d
Flags: bus master, 66MHz, fast devsel, latency 0, IRQ 20
I/O ports at 34d8 [size=8]
I/O ports at 34cc [size=4]
I/O ports at 34d0 [size=8]
I/O ports at 34c8 [size=4]
I/O ports at 34a0 [size=16]
Memory at d0007000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [44] Power Management version 2
Capabilities: [b0] Message Signalled Interrupts: Mask- 64bit+
Queue=0/2 Enable-
Capabilities: [cc] HyperTransport: MSI Mapping Enable+ Fixed+
Kernel driver in use: sata_nv
Kernel modules: ata_generic, sata_nv, pata_acpi
I've connected a SATA to eSATA adapter on an internal port and
connected the eSATA port to a Thermaltake docking station:
http://www.thermaltakeusa.com/Product.aspx?C=1346&ID=1731
When I "eject" the drive I see no dmesg output related to hotplug. I
also don't see anything when I plug a drive in.
scsi0 : sata_nv
scsi1 : sata_nv
ata1: SATA max UDMA/133 cmd 0x34c0 ctl 0x34b4 bmdma 0x3490 irq 21
ata2: SATA max UDMA/133 cmd 0x34b8 ctl 0x34b0 bmdma 0x3498 irq 21
ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata1.00: ATA-7: HITACHI HDS7225SCSUN250G 0721BA6TRD, V5DOA7BA, max
UDMA/133
ata1.00: 488390625 sectors, multi 16: LBA48 NCQ (depth 0/32)
ata1.00: configured for UDMA/133
ata2: SATA link down (SStatus 0 SControl 300)
scsi 0:0:0:0: Direct-Access ATA HITACHI HDS7225S V5DO PQ: 0
ANSI: 5
sd 0:0:0:0: [sda] 488390625 512-byte hardware sectors (250056 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't
support DPO or FUA
sd 0:0:0:0: [sda] 488390625 512-byte hardware sectors (250056 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't
support DPO or FUA
sda: sda1 sda2 sda3
sd 0:0:0:0: [sda] Attached SCSI disk
ACPI: PCI Interrupt 0000:00:05.1[B] -> Link [LSI1] -> GSI 20 (level,
low) -> IRQ 20
PCI: Setting latency timer of device 0000:00:05.1 to 64
scsi2 : sata_nv
scsi3 : sata_nv
ata3: SATA max UDMA/133 cmd 0x34d8 ctl 0x34cc bmdma 0x34a0 irq 20
ata4: SATA max UDMA/133 cmd 0x34d0 ctl 0x34c8 bmdma 0x34a8 irq 20
ata3: SATA link down (SStatus 0 SControl 300)
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: ATA-7: ST3808110AS, 3.AAE, max UDMA/133
ata4.00: 156301488 sectors, multi 16: LBA48 NCQ (depth 0/32)
ata4.00: configured for UDMA/133
scsi 3:0:0:0: Direct-Access ATA ST3808110AS 3.AA PQ: 0
ANSI: 5
sd 3:0:0:0: [sdb] 156301488 512-byte hardware sectors (80026 MB)
sd 3:0:0:0: [sdb] Write Protect is off
sd 3:0:0:0: [sdb] Mode Sense: 00 3a 00 00
sd 3:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't
support DPO or FUA
sd 3:0:0:0: [sdb] 156301488 512-byte hardware sectors (80026 MB)
sd 3:0:0:0: [sdb] Write Protect is off
sd 3:0:0:0: [sdb] Mode Sense: 00 3a 00 00
sd 3:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't
support DPO or FUA
sdb: sdb1 sdb2 sdb3 sdb4
sd 3:0:0:0: [sdb] Attached SCSI disk
kjournald starting. Commit interval 5 seconds
Is there something I'm doing wrong w/regards to SATA hotplug support?
- k
--
To unsubscribe from this list: send the line "unsubscribe linux-ide" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
