[RFC: 2.6 patch] remove BLK_DEV_HD_ONLY

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



This was the oldest and most limited of the three IDE drivers we ship.

Signed-off-by: Adrian Bunk <bunk@xxxxxxxxxx>

---

 drivers/ide/Kconfig     |   25 -
 drivers/ide/Makefile    |    5 
 drivers/ide/legacy/hd.c |  815 ----------------------------------------
 3 files changed, 845 deletions(-)

421b85dab5d56e609b1bdddb2e7d89d78c0eb1d0 diff --git a/drivers/ide/Kconfig b/drivers/ide/Kconfig
index b4f3aef..c2ea153 100644
--- a/drivers/ide/Kconfig
+++ b/drivers/ide/Kconfig
@@ -1026,29 +1026,4 @@ config BLK_DEV_IDEDMA
 
 endif
 
-config BLK_DEV_HD_ONLY
-	bool "Old hard disk (MFM/RLL/IDE) driver"
-	help
-	  There are two drivers for MFM/RLL/IDE hard disks. Most people use
-	  the newer enhanced driver, but this old one is still around for two
-	  reasons. Some older systems have strange timing problems and seem to
-	  work only with the old driver (which itself does not work with some
-	  newer systems). The other reason is that the old driver is smaller,
-	  since it lacks the enhanced functionality of the new one. This makes
-	  it a good choice for systems with very tight memory restrictions, or
-	  for systems with only older MFM/RLL/ESDI drives. Choosing the old
-	  driver can save 13 KB or so of kernel memory.
-
-	  If you want to use this driver together with the new one you have
-	  to use "hda=noprobe hdb=noprobe" kernel parameters to prevent the new
-	  driver from probing the primary interface.
-
-	  If you are unsure, then just choose the Enhanced IDE/MFM/RLL driver
-	  instead of this one. For more detailed information, read the
-	  Disk-HOWTO, available from
-	  <http://www.tldp.org/docs.html#howto>.
-
-config BLK_DEV_HD
-	def_bool BLK_DEV_HD_ONLY
-
 endif # IDE
diff --git a/drivers/ide/Makefile b/drivers/ide/Makefile
index f94b679..1309f85 100644
--- a/drivers/ide/Makefile
+++ b/drivers/ide/Makefile
@@ -59,8 +59,3 @@ endif
 
 obj-$(CONFIG_BLK_DEV_IDE)		+= arm/ mips/
 
-# old hd driver must be last
-ifeq ($(CONFIG_BLK_DEV_HD), y)
-	hd-core-y += legacy/hd.o
-	obj-y += hd-core.o
-endif
diff --git a/drivers/ide/legacy/hd.c b/drivers/ide/legacy/hd.c
deleted file mode 100644
index abdedf5..0000000
--- a/drivers/ide/legacy/hd.c
+++ /dev/null
@@ -1,815 +0,0 @@
-/*
- *  Copyright (C) 1991, 1992  Linus Torvalds
- *
- * This is the low-level hd interrupt support. It traverses the
- * request-list, using interrupts to jump between functions. As
- * all the functions are called within interrupts, we may not
- * sleep. Special care is recommended.
- *
- *  modified by Drew Eckhardt to check nr of hd's from the CMOS.
- *
- *  Thanks to Branko Lankester, lankeste@xxxxxxxxxx, who found a bug
- *  in the early extended-partition checks and added DM partitions
- *
- *  IRQ-unmask, drive-id, multiple-mode, support for ">16 heads",
- *  and general streamlining by Mark Lord.
- *
- *  Removed 99% of above. Use Mark's ide driver for those options.
- *  This is now a lightweight ST-506 driver. (Paul Gortmaker)
- *
- *  Modified 1995 Russell King for ARM processor.
- *
- *  Bugfix: max_sectors must be <= 255 or the wheels tend to come
- *  off in a hurry once you queue things up - Paul G. 02/2001
- */
-
-/* Uncomment the following if you want verbose error reports. */
-/* #define VERBOSE_ERRORS */
-
-#include <linux/blkdev.h>
-#include <linux/errno.h>
-#include <linux/signal.h>
-#include <linux/interrupt.h>
-#include <linux/timer.h>
-#include <linux/fs.h>
-#include <linux/kernel.h>
-#include <linux/genhd.h>
-#include <linux/slab.h>
-#include <linux/string.h>
-#include <linux/ioport.h>
-#include <linux/mc146818rtc.h> /* CMOS defines */
-#include <linux/init.h>
-#include <linux/blkpg.h>
-#include <linux/hdreg.h>
-
-#define REALLY_SLOW_IO
-#include <asm/system.h>
-#include <asm/io.h>
-#include <asm/uaccess.h>
-
-#ifdef __arm__
-#undef  HD_IRQ
-#endif
-#include <asm/irq.h>
-#ifdef __arm__
-#define HD_IRQ IRQ_HARDDISK
-#endif
-
-/* Hd controller regster ports */
-
-#define HD_DATA		0x1f0		/* _CTL when writing */
-#define HD_ERROR	0x1f1		/* see err-bits */
-#define HD_NSECTOR	0x1f2		/* nr of sectors to read/write */
-#define HD_SECTOR	0x1f3		/* starting sector */
-#define HD_LCYL		0x1f4		/* starting cylinder */
-#define HD_HCYL		0x1f5		/* high byte of starting cyl */
-#define HD_CURRENT	0x1f6		/* 101dhhhh , d=drive, hhhh=head */
-#define HD_STATUS	0x1f7		/* see status-bits */
-#define HD_FEATURE	HD_ERROR	/* same io address, read=error, write=feature */
-#define HD_PRECOMP	HD_FEATURE	/* obsolete use of this port - predates IDE */
-#define HD_COMMAND	HD_STATUS	/* same io address, read=status, write=cmd */
-
-#define HD_CMD		0x3f6		/* used for resets */
-#define HD_ALTSTATUS	0x3f6		/* same as HD_STATUS but doesn't clear irq */
-
-/* Bits of HD_STATUS */
-#define ERR_STAT		0x01
-#define INDEX_STAT		0x02
-#define ECC_STAT		0x04	/* Corrected error */
-#define DRQ_STAT		0x08
-#define SEEK_STAT		0x10
-#define SERVICE_STAT		SEEK_STAT
-#define WRERR_STAT		0x20
-#define READY_STAT		0x40
-#define BUSY_STAT		0x80
-
-/* Bits for HD_ERROR */
-#define MARK_ERR		0x01	/* Bad address mark */
-#define TRK0_ERR		0x02	/* couldn't find track 0 */
-#define ABRT_ERR		0x04	/* Command aborted */
-#define MCR_ERR			0x08	/* media change request */
-#define ID_ERR			0x10	/* ID field not found */
-#define MC_ERR			0x20	/* media changed */
-#define ECC_ERR			0x40	/* Uncorrectable ECC error */
-#define BBD_ERR			0x80	/* pre-EIDE meaning:  block marked bad */
-#define ICRC_ERR		0x80	/* new meaning:  CRC error during transfer */
-
-static DEFINE_SPINLOCK(hd_lock);
-static struct request_queue *hd_queue;
-
-#define MAJOR_NR HD_MAJOR
-#define QUEUE (hd_queue)
-#define CURRENT elv_next_request(hd_queue)
-
-#define TIMEOUT_VALUE	(6*HZ)
-#define	HD_DELAY	0
-
-#define MAX_ERRORS     16	/* Max read/write errors/sector */
-#define RESET_FREQ      8	/* Reset controller every 8th retry */
-#define RECAL_FREQ      4	/* Recalibrate every 4th retry */
-#define MAX_HD		2
-
-#define STAT_OK		(READY_STAT|SEEK_STAT)
-#define OK_STATUS(s)	(((s)&(STAT_OK|(BUSY_STAT|WRERR_STAT|ERR_STAT)))==STAT_OK)
-
-static void recal_intr(void);
-static void bad_rw_intr(void);
-
-static int reset;
-static int hd_error;
-
-/*
- *  This struct defines the HD's and their types.
- */
-struct hd_i_struct {
-	unsigned int head, sect, cyl, wpcom, lzone, ctl;
-	int unit;
-	int recalibrate;
-	int special_op;
-};
-
-#ifdef HD_TYPE
-static struct hd_i_struct hd_info[] = { HD_TYPE };
-static int NR_HD = ARRAY_SIZE(hd_info);
-#else
-static struct hd_i_struct hd_info[MAX_HD];
-static int NR_HD;
-#endif
-
-static struct gendisk *hd_gendisk[MAX_HD];
-
-static struct timer_list device_timer;
-
-#define TIMEOUT_VALUE (6*HZ)
-
-#define SET_TIMER							\
-	do {								\
-		mod_timer(&device_timer, jiffies + TIMEOUT_VALUE);	\
-	} while (0)
-
-static void (*do_hd)(void) = NULL;
-#define SET_HANDLER(x) \
-if ((do_hd = (x)) != NULL) \
-	SET_TIMER; \
-else \
-	del_timer(&device_timer);
-
-
-#if (HD_DELAY > 0)
-
-#include <asm/i8253.h>
-
-unsigned long last_req;
-
-unsigned long read_timer(void)
-{
-	unsigned long t, flags;
-	int i;
-
-	spin_lock_irqsave(&i8253_lock, flags);
-	t = jiffies * 11932;
-	outb_p(0, 0x43);
-	i = inb_p(0x40);
-	i |= inb(0x40) << 8;
-	spin_unlock_irqrestore(&i8253_lock, flags);
-	return(t - i);
-}
-#endif
-
-static void __init hd_setup(char *str, int *ints)
-{
-	int hdind = 0;
-
-	if (ints[0] != 3)
-		return;
-	if (hd_info[0].head != 0)
-		hdind = 1;
-	hd_info[hdind].head = ints[2];
-	hd_info[hdind].sect = ints[3];
-	hd_info[hdind].cyl = ints[1];
-	hd_info[hdind].wpcom = 0;
-	hd_info[hdind].lzone = ints[1];
-	hd_info[hdind].ctl = (ints[2] > 8 ? 8 : 0);
-	NR_HD = hdind+1;
-}
-
-static void dump_status(const char *msg, unsigned int stat)
-{
-	char *name = "hd?";
-	if (CURRENT)
-		name = CURRENT->rq_disk->disk_name;
-
-#ifdef VERBOSE_ERRORS
-	printk("%s: %s: status=0x%02x { ", name, msg, stat & 0xff);
-	if (stat & BUSY_STAT)	printk("Busy ");
-	if (stat & READY_STAT)	printk("DriveReady ");
-	if (stat & WRERR_STAT)	printk("WriteFault ");
-	if (stat & SEEK_STAT)	printk("SeekComplete ");
-	if (stat & DRQ_STAT)	printk("DataRequest ");
-	if (stat & ECC_STAT)	printk("CorrectedError ");
-	if (stat & INDEX_STAT)	printk("Index ");
-	if (stat & ERR_STAT)	printk("Error ");
-	printk("}\n");
-	if ((stat & ERR_STAT) == 0) {
-		hd_error = 0;
-	} else {
-		hd_error = inb(HD_ERROR);
-		printk("%s: %s: error=0x%02x { ", name, msg, hd_error & 0xff);
-		if (hd_error & BBD_ERR)		printk("BadSector ");
-		if (hd_error & ECC_ERR)		printk("UncorrectableError ");
-		if (hd_error & ID_ERR)		printk("SectorIdNotFound ");
-		if (hd_error & ABRT_ERR)	printk("DriveStatusError ");
-		if (hd_error & TRK0_ERR)	printk("TrackZeroNotFound ");
-		if (hd_error & MARK_ERR)	printk("AddrMarkNotFound ");
-		printk("}");
-		if (hd_error & (BBD_ERR|ECC_ERR|ID_ERR|MARK_ERR)) {
-			printk(", CHS=%d/%d/%d", (inb(HD_HCYL)<<8) + inb(HD_LCYL),
-				inb(HD_CURRENT) & 0xf, inb(HD_SECTOR));
-			if (CURRENT)
-				printk(", sector=%ld", CURRENT->sector);
-		}
-		printk("\n");
-	}
-#else
-	printk("%s: %s: status=0x%02x.\n", name, msg, stat & 0xff);
-	if ((stat & ERR_STAT) == 0) {
-		hd_error = 0;
-	} else {
-		hd_error = inb(HD_ERROR);
-		printk("%s: %s: error=0x%02x.\n", name, msg, hd_error & 0xff);
-	}
-#endif
-}
-
-static void check_status(void)
-{
-	int i = inb_p(HD_STATUS);
-
-	if (!OK_STATUS(i)) {
-		dump_status("check_status", i);
-		bad_rw_intr();
-	}
-}
-
-static int controller_busy(void)
-{
-	int retries = 100000;
-	unsigned char status;
-
-	do {
-		status = inb_p(HD_STATUS);
-	} while ((status & BUSY_STAT) && --retries);
-	return status;
-}
-
-static int status_ok(void)
-{
-	unsigned char status = inb_p(HD_STATUS);
-
-	if (status & BUSY_STAT)
-		return 1;	/* Ancient, but does it make sense??? */
-	if (status & WRERR_STAT)
-		return 0;
-	if (!(status & READY_STAT))
-		return 0;
-	if (!(status & SEEK_STAT))
-		return 0;
-	return 1;
-}
-
-static int controller_ready(unsigned int drive, unsigned int head)
-{
-	int retry = 100;
-
-	do {
-		if (controller_busy() & BUSY_STAT)
-			return 0;
-		outb_p(0xA0 | (drive<<4) | head, HD_CURRENT);
-		if (status_ok())
-			return 1;
-	} while (--retry);
-	return 0;
-}
-
-static void hd_out(struct hd_i_struct *disk,
-		   unsigned int nsect,
-		   unsigned int sect,
-		   unsigned int head,
-		   unsigned int cyl,
-		   unsigned int cmd,
-		   void (*intr_addr)(void))
-{
-	unsigned short port;
-
-#if (HD_DELAY > 0)
-	while (read_timer() - last_req < HD_DELAY)
-		/* nothing */;
-#endif
-	if (reset)
-		return;
-	if (!controller_ready(disk->unit, head)) {
-		reset = 1;
-		return;
-	}
-	SET_HANDLER(intr_addr);
-	outb_p(disk->ctl, HD_CMD);
-	port = HD_DATA;
-	outb_p(disk->wpcom >> 2, ++port);
-	outb_p(nsect, ++port);
-	outb_p(sect, ++port);
-	outb_p(cyl, ++port);
-	outb_p(cyl >> 8, ++port);
-	outb_p(0xA0 | (disk->unit << 4) | head, ++port);
-	outb_p(cmd, ++port);
-}
-
-static void hd_request (void);
-
-static int drive_busy(void)
-{
-	unsigned int i;
-	unsigned char c;
-
-	for (i = 0; i < 500000 ; i++) {
-		c = inb_p(HD_STATUS);
-		if ((c & (BUSY_STAT | READY_STAT | SEEK_STAT)) == STAT_OK)
-			return 0;
-	}
-	dump_status("reset timed out", c);
-	return 1;
-}
-
-static void reset_controller(void)
-{
-	int	i;
-
-	outb_p(4, HD_CMD);
-	for (i = 0; i < 1000; i++) barrier();
-	outb_p(hd_info[0].ctl & 0x0f, HD_CMD);
-	for (i = 0; i < 1000; i++) barrier();
-	if (drive_busy())
-		printk("hd: controller still busy\n");
-	else if ((hd_error = inb(HD_ERROR)) != 1)
-		printk("hd: controller reset failed: %02x\n", hd_error);
-}
-
-static void reset_hd(void)
-{
-	static int i;
-
-repeat:
-	if (reset) {
-		reset = 0;
-		i = -1;
-		reset_controller();
-	} else {
-		check_status();
-		if (reset)
-			goto repeat;
-	}
-	if (++i < NR_HD) {
-		struct hd_i_struct *disk = &hd_info[i];
-		disk->special_op = disk->recalibrate = 1;
-		hd_out(disk, disk->sect, disk->sect, disk->head-1,
-			disk->cyl, WIN_SPECIFY, &reset_hd);
-		if (reset)
-			goto repeat;
-	} else
-		hd_request();
-}
-
-/*
- * Ok, don't know what to do with the unexpected interrupts: on some machines
- * doing a reset and a retry seems to result in an eternal loop. Right now I
- * ignore it, and just set the timeout.
- *
- * On laptops (and "green" PCs), an unexpected interrupt occurs whenever the
- * drive enters "idle", "standby", or "sleep" mode, so if the status looks
- * "good", we just ignore the interrupt completely.
- */
-static void unexpected_hd_interrupt(void)
-{
-	unsigned int stat = inb_p(HD_STATUS);
-
-	if (stat & (BUSY_STAT|DRQ_STAT|ECC_STAT|ERR_STAT)) {
-		dump_status("unexpected interrupt", stat);
-		SET_TIMER;
-	}
-}
-
-/*
- * bad_rw_intr() now tries to be a bit smarter and does things
- * according to the error returned by the controller.
- * -Mika Liljeberg (liljeber@xxxxxxxxxxxxxx)
- */
-static void bad_rw_intr(void)
-{
-	struct request *req = CURRENT;
-	if (req != NULL) {
-		struct hd_i_struct *disk = req->rq_disk->private_data;
-		if (++req->errors >= MAX_ERRORS || (hd_error & BBD_ERR)) {
-			end_request(req, 0);
-			disk->special_op = disk->recalibrate = 1;
-		} else if (req->errors % RESET_FREQ == 0)
-			reset = 1;
-		else if ((hd_error & TRK0_ERR) || req->errors % RECAL_FREQ == 0)
-			disk->special_op = disk->recalibrate = 1;
-		/* Otherwise just retry */
-	}
-}
-
-static inline int wait_DRQ(void)
-{
-	int retries;
-	int stat;
-
-	for (retries = 0; retries < 100000; retries++) {
-		stat = inb_p(HD_STATUS);
-		if (stat & DRQ_STAT)
-			return 0;
-	}
-	dump_status("wait_DRQ", stat);
-	return -1;
-}
-
-static void read_intr(void)
-{
-	struct request *req;
-	int i, retries = 100000;
-
-	do {
-		i = (unsigned) inb_p(HD_STATUS);
-		if (i & BUSY_STAT)
-			continue;
-		if (!OK_STATUS(i))
-			break;
-		if (i & DRQ_STAT)
-			goto ok_to_read;
-	} while (--retries > 0);
-	dump_status("read_intr", i);
-	bad_rw_intr();
-	hd_request();
-	return;
-ok_to_read:
-	req = CURRENT;
-	insw(HD_DATA, req->buffer, 256);
-	req->sector++;
-	req->buffer += 512;
-	req->errors = 0;
-	i = --req->nr_sectors;
-	--req->current_nr_sectors;
-#ifdef DEBUG
-	printk("%s: read: sector %ld, remaining = %ld, buffer=%p\n",
-		req->rq_disk->disk_name, req->sector, req->nr_sectors,
-		req->buffer+512);
-#endif
-	if (req->current_nr_sectors <= 0)
-		end_request(req, 1);
-	if (i > 0) {
-		SET_HANDLER(&read_intr);
-		return;
-	}
-	(void) inb_p(HD_STATUS);
-#if (HD_DELAY > 0)
-	last_req = read_timer();
-#endif
-	if (elv_next_request(QUEUE))
-		hd_request();
-	return;
-}
-
-static void write_intr(void)
-{
-	struct request *req = CURRENT;
-	int i;
-	int retries = 100000;
-
-	do {
-		i = (unsigned) inb_p(HD_STATUS);
-		if (i & BUSY_STAT)
-			continue;
-		if (!OK_STATUS(i))
-			break;
-		if ((req->nr_sectors <= 1) || (i & DRQ_STAT))
-			goto ok_to_write;
-	} while (--retries > 0);
-	dump_status("write_intr", i);
-	bad_rw_intr();
-	hd_request();
-	return;
-ok_to_write:
-	req->sector++;
-	i = --req->nr_sectors;
-	--req->current_nr_sectors;
-	req->buffer += 512;
-	if (!i || (req->bio && req->current_nr_sectors <= 0))
-		end_request(req, 1);
-	if (i > 0) {
-		SET_HANDLER(&write_intr);
-		outsw(HD_DATA, req->buffer, 256);
-		local_irq_enable();
-	} else {
-#if (HD_DELAY > 0)
-		last_req = read_timer();
-#endif
-		hd_request();
-	}
-	return;
-}
-
-static void recal_intr(void)
-{
-	check_status();
-#if (HD_DELAY > 0)
-	last_req = read_timer();
-#endif
-	hd_request();
-}
-
-/*
- * This is another of the error-routines I don't know what to do with. The
- * best idea seems to just set reset, and start all over again.
- */
-static void hd_times_out(unsigned long dummy)
-{
-	char *name;
-
-	do_hd = NULL;
-
-	if (!CURRENT)
-		return;
-
-	disable_irq(HD_IRQ);
-	local_irq_enable();
-	reset = 1;
-	name = CURRENT->rq_disk->disk_name;
-	printk("%s: timeout\n", name);
-	if (++CURRENT->errors >= MAX_ERRORS) {
-#ifdef DEBUG
-		printk("%s: too many errors\n", name);
-#endif
-		end_request(CURRENT, 0);
-	}
-	local_irq_disable();
-	hd_request();
-	enable_irq(HD_IRQ);
-}
-
-static int do_special_op(struct hd_i_struct *disk, struct request *req)
-{
-	if (disk->recalibrate) {
-		disk->recalibrate = 0;
-		hd_out(disk, disk->sect, 0, 0, 0, WIN_RESTORE, &recal_intr);
-		return reset;
-	}
-	if (disk->head > 16) {
-		printk("%s: cannot handle device with more than 16 heads - giving up\n", req->rq_disk->disk_name);
-		end_request(req, 0);
-	}
-	disk->special_op = 0;
-	return 1;
-}
-
-/*
- * The driver enables interrupts as much as possible.  In order to do this,
- * (a) the device-interrupt is disabled before entering hd_request(),
- * and (b) the timeout-interrupt is disabled before the sti().
- *
- * Interrupts are still masked (by default) whenever we are exchanging
- * data/cmds with a drive, because some drives seem to have very poor
- * tolerance for latency during I/O. The IDE driver has support to unmask
- * interrupts for non-broken hardware, so use that driver if required.
- */
-static void hd_request(void)
-{
-	unsigned int block, nsect, sec, track, head, cyl;
-	struct hd_i_struct *disk;
-	struct request *req;
-
-	if (do_hd)
-		return;
-repeat:
-	del_timer(&device_timer);
-	local_irq_enable();
-
-	req = CURRENT;
-	if (!req) {
-		do_hd = NULL;
-		return;
-	}
-
-	if (reset) {
-		local_irq_disable();
-		reset_hd();
-		return;
-	}
-	disk = req->rq_disk->private_data;
-	block = req->sector;
-	nsect = req->nr_sectors;
-	if (block >= get_capacity(req->rq_disk) ||
-	    ((block+nsect) > get_capacity(req->rq_disk))) {
-		printk("%s: bad access: block=%d, count=%d\n",
-			req->rq_disk->disk_name, block, nsect);
-		end_request(req, 0);
-		goto repeat;
-	}
-
-	if (disk->special_op) {
-		if (do_special_op(disk, req))
-			goto repeat;
-		return;
-	}
-	sec   = block % disk->sect + 1;
-	track = block / disk->sect;
-	head  = track % disk->head;
-	cyl   = track / disk->head;
-#ifdef DEBUG
-	printk("%s: %sing: CHS=%d/%d/%d, sectors=%d, buffer=%p\n",
-		req->rq_disk->disk_name,
-		req_data_dir(req) == READ ? "read" : "writ",
-		cyl, head, sec, nsect, req->buffer);
-#endif
-	if (blk_fs_request(req)) {
-		switch (rq_data_dir(req)) {
-		case READ:
-			hd_out(disk, nsect, sec, head, cyl, WIN_READ,
-				&read_intr);
-			if (reset)
-				goto repeat;
-			break;
-		case WRITE:
-			hd_out(disk, nsect, sec, head, cyl, WIN_WRITE,
-				&write_intr);
-			if (reset)
-				goto repeat;
-			if (wait_DRQ()) {
-				bad_rw_intr();
-				goto repeat;
-			}
-			outsw(HD_DATA, req->buffer, 256);
-			break;
-		default:
-			printk("unknown hd-command\n");
-			end_request(req, 0);
-			break;
-		}
-	}
-}
-
-static void do_hd_request(struct request_queue *q)
-{
-	disable_irq(HD_IRQ);
-	hd_request();
-	enable_irq(HD_IRQ);
-}
-
-static int hd_getgeo(struct block_device *bdev, struct hd_geometry *geo)
-{
-	struct hd_i_struct *disk = bdev->bd_disk->private_data;
-
-	geo->heads = disk->head;
-	geo->sectors = disk->sect;
-	geo->cylinders = disk->cyl;
-	return 0;
-}
-
-/*
- * Releasing a block device means we sync() it, so that it can safely
- * be forgotten about...
- */
-
-static irqreturn_t hd_interrupt(int irq, void *dev_id)
-{
-	void (*handler)(void) = do_hd;
-
-	do_hd = NULL;
-	del_timer(&device_timer);
-	if (!handler)
-		handler = unexpected_hd_interrupt;
-	handler();
-	local_irq_enable();
-	return IRQ_HANDLED;
-}
-
-static struct block_device_operations hd_fops = {
-	.getgeo =	hd_getgeo,
-};
-
-/*
- * This is the hard disk IRQ description. The IRQF_DISABLED in sa_flags
- * means we run the IRQ-handler with interrupts disabled:  this is bad for
- * interrupt latency, but anything else has led to problems on some
- * machines.
- *
- * We enable interrupts in some of the routines after making sure it's
- * safe.
- */
-
-static int __init hd_init(void)
-{
-	int drive;
-
-	if (register_blkdev(MAJOR_NR, "hd"))
-		return -1;
-
-	hd_queue = blk_init_queue(do_hd_request, &hd_lock);
-	if (!hd_queue) {
-		unregister_blkdev(MAJOR_NR, "hd");
-		return -ENOMEM;
-	}
-
-	blk_queue_max_sectors(hd_queue, 255);
-	init_timer(&device_timer);
-	device_timer.function = hd_times_out;
-	blk_queue_hardsect_size(hd_queue, 512);
-
-	if (!NR_HD) {
-		/*
-		 * We don't know anything about the drive.  This means
-		 * that you *MUST* specify the drive parameters to the
-		 * kernel yourself.
-		 *
-		 * If we were on an i386, we used to read this info from
-		 * the BIOS or CMOS.  This doesn't work all that well,
-		 * since this assumes that this is a primary or secondary
-		 * drive, and if we're using this legacy driver, it's
-		 * probably an auxilliary controller added to recover
-		 * legacy data off an ST-506 drive.  Either way, it's
-		 * definitely safest to have the user explicitly specify
-		 * the information.
-		 */
-		printk("hd: no drives specified - use hd=cyl,head,sectors"
-			" on kernel command line\n");
-		goto out;
-	}
-
-	for (drive = 0 ; drive < NR_HD ; drive++) {
-		struct gendisk *disk = alloc_disk(64);
-		struct hd_i_struct *p = &hd_info[drive];
-		if (!disk)
-			goto Enomem;
-		disk->major = MAJOR_NR;
-		disk->first_minor = drive << 6;
-		disk->fops = &hd_fops;
-		sprintf(disk->disk_name, "hd%c", 'a'+drive);
-		disk->private_data = p;
-		set_capacity(disk, p->head * p->sect * p->cyl);
-		disk->queue = hd_queue;
-		p->unit = drive;
-		hd_gendisk[drive] = disk;
-		printk("%s: %luMB, CHS=%d/%d/%d\n",
-			disk->disk_name, (unsigned long)get_capacity(disk)/2048,
-			p->cyl, p->head, p->sect);
-	}
-
-	if (request_irq(HD_IRQ, hd_interrupt, IRQF_DISABLED, "hd", NULL)) {
-		printk("hd: unable to get IRQ%d for the hard disk driver\n",
-			HD_IRQ);
-		goto out1;
-	}
-	if (!request_region(HD_DATA, 8, "hd")) {
-		printk(KERN_WARNING "hd: port 0x%x busy\n", HD_DATA);
-		goto out2;
-	}
-	if (!request_region(HD_CMD, 1, "hd(cmd)")) {
-		printk(KERN_WARNING "hd: port 0x%x busy\n", HD_CMD);
-		goto out3;
-	}
-
-	/* Let them fly */
-	for (drive = 0; drive < NR_HD; drive++)
-		add_disk(hd_gendisk[drive]);
-
-	return 0;
-
-out3:
-	release_region(HD_DATA, 8);
-out2:
-	free_irq(HD_IRQ, NULL);
-out1:
-	for (drive = 0; drive < NR_HD; drive++)
-		put_disk(hd_gendisk[drive]);
-	NR_HD = 0;
-out:
-	del_timer(&device_timer);
-	unregister_blkdev(MAJOR_NR, "hd");
-	blk_cleanup_queue(hd_queue);
-	return -1;
-Enomem:
-	while (drive--)
-		put_disk(hd_gendisk[drive]);
-	goto out;
-}
-
-static int __init parse_hd_setup(char *line)
-{
-	int ints[6];
-
-	(void) get_options(line, ARRAY_SIZE(ints), ints);
-	hd_setup(NULL, ints);
-
-	return 1;
-}
-__setup("hd=", parse_hd_setup);
-
-module_init(hd_init);

--
To unsubscribe from this list: send the line "unsubscribe linux-ide" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html

[Index of Archives]     [Linux Filesystems]     [Linux SCSI]     [Linux RAID]     [Git]     [Kernel Newbies]     [Linux Newbie]     [Security]     [Netfilter]     [Bugtraq]     [Yosemite News]     [MIPS Linux]     [ARM Linux]     [Linux Security]     [Samba]     [Device Mapper]

  Powered by Linux