* Check IDEFLOPPY_FLAG_ZIP_DRIVE flag in idefloppy_transfer_pc1()
and skip idefloppy_transfer_pc2()-phase if the flag is not set.
* Always use idefloppy_transfer_pc1() in idefloppy_issue_pc()
and remove no longer needed idefloppy_transfer_pc().
There should be no functional changes caused by this patch.
Cc: Borislav Petkov <petkovbb@xxxxxxxxx>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@xxxxxxxxx>
---
drivers/ide/ide-floppy.c | 65 ++++++++++++-----------------------------------
1 file changed, 17 insertions(+), 48 deletions(-)
Index: b/drivers/ide/ide-floppy.c
===================================================================
--- a/drivers/ide/ide-floppy.c
+++ b/drivers/ide/ide-floppy.c
@@ -522,40 +522,6 @@ static ide_startstop_t idefloppy_pc_intr
}
/*
- * This is the original routine that did the packet transfer.
- * It fails at high speeds on the Iomega ZIP drive, so there's a slower version
- * for that drive below. The algorithm is chosen based on drive type
- */
-static ide_startstop_t idefloppy_transfer_pc(ide_drive_t *drive)
-{
- ide_hwif_t *hwif = drive->hwif;
- ide_startstop_t startstop;
- idefloppy_floppy_t *floppy = drive->driver_data;
- u8 ireason;
-
- if (ide_wait_stat(&startstop, drive, DRQ_STAT, BUSY_STAT, WAIT_READY)) {
- printk(KERN_ERR "ide-floppy: Strange, packet command "
- "initiated yet DRQ isn't asserted\n");
- return startstop;
- }
- ireason = hwif->INB(hwif->io_ports.nsect_addr);
- if ((ireason & CD) == 0 || (ireason & IO)) {
- printk(KERN_ERR "ide-floppy: (IO,CoD) != (0,1) while "
- "issuing a packet command\n");
- return ide_do_reset(drive);
- }
-
- /* Set the interrupt routine */
- ide_set_handler(drive, &idefloppy_pc_intr, IDEFLOPPY_WAIT_CMD, NULL);
-
- /* Send the actual packet */
- hwif->output_data(drive, NULL, floppy->pc->c, 12);
-
- return ide_started;
-}
-
-
-/*
* What we have here is a classic case of a top half / bottom half interrupt
* service routine. In interrupt mode, the device sends an interrupt to signal
* that it is ready to receive a packet. However, we need to delay about 2-3
@@ -580,6 +546,8 @@ static ide_startstop_t idefloppy_transfe
{
ide_hwif_t *hwif = drive->hwif;
idefloppy_floppy_t *floppy = drive->driver_data;
+ ide_expiry_t *expiry;
+ unsigned int timeout;
ide_startstop_t startstop;
u8 ireason;
@@ -602,9 +570,20 @@ static ide_startstop_t idefloppy_transfe
* 40 and 50msec work well. idefloppy_pc_intr will not be actually
* used until after the packet is moved in about 50 msec.
*/
+ if (floppy->flags & IDEFLOPPY_FLAG_ZIP_DRIVE) {
+ timeout = floppy->ticks;
+ expiry = &idefloppy_transfer_pc2;
+ } else {
+ timeout = IDEFLOPPY_WAIT_CMD;
+ expiry = NULL;
+ }
+
+ ide_set_handler(drive, &idefloppy_pc_intr, timeout, expiry);
+
+ if ((floppy->flags & IDEFLOPPY_FLAG_ZIP_DRIVE) == 0)
+ /* Send the actual packet */
+ hwif->output_data(drive, NULL, floppy->pc->c, 12);
- ide_set_handler(drive, &idefloppy_pc_intr, floppy->ticks,
- &idefloppy_transfer_pc2);
return ide_started;
}
@@ -629,7 +608,6 @@ static ide_startstop_t idefloppy_issue_p
{
idefloppy_floppy_t *floppy = drive->driver_data;
ide_hwif_t *hwif = drive->hwif;
- ide_handler_t *pkt_xfer_routine;
u16 bcount;
u8 dma;
@@ -675,26 +653,17 @@ static ide_startstop_t idefloppy_issue_p
hwif->dma_ops->dma_start(drive);
}
- /* Can we transfer the packet when we get the interrupt or wait? */
- if (floppy->flags & IDEFLOPPY_FLAG_ZIP_DRIVE) {
- /* wait */
- pkt_xfer_routine = &idefloppy_transfer_pc1;
- } else {
- /* immediate */
- pkt_xfer_routine = &idefloppy_transfer_pc;
- }
-
if (floppy->flags & IDEFLOPPY_FLAG_DRQ_INTERRUPT) {
/* Issue the packet command */
ide_execute_command(drive, WIN_PACKETCMD,
- pkt_xfer_routine,
+ &idefloppy_transfer_pc1,
IDEFLOPPY_WAIT_CMD,
NULL);
return ide_started;
} else {
/* Issue the packet command */
ide_execute_pkt_cmd(drive);
- return (*pkt_xfer_routine) (drive);
+ return idefloppy_transfer_pc1(drive);
}
}
--
To unsubscribe from this list: send the line "unsubscribe linux-ide" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
