Hi Gurus! Preamble: I've been following this list for several months now trying to spot a similar issue or to gain knowledge to resolve mine. I'm pretty sure the problem is with my setup/configuration, but I've been unable to fix it so far. I would be eternally grateful if someone can help me in resolving the issue. Thanks in advance. Setup: I'm running a fileserver with array of 10 disks (8 Seagate 500GB 7200.9 and 7200.10 plus 2 Maxtors) on 3 Addonics ADSA4R5 (4-port SATA2 PCI on Sil 3124) cards in JBOD configuration. The host is a little bit outdated and is dual AMD Athlon MP 1900+ on Tyan Tiger MPX (S2466N-4M) with 1GB of RAM. SATA cards are in PCI slots, not PCI-X. Most of the time drives are in standby mode (30min timeout), but it does not make any difference with issues I'm seeing. Filesystem used is XFS and all the disks are shared over NFS. Power supply was originally 550 watt Enermax (should be enough power, according to a wattmeter), but to be sure was replaced to 750 watt Coolermaster. The kernel is currently 2.6.23.9, but I tried many other versions from 2.6.21 to 2.6.24. The system is Gentoo, but the kernel is vanilla. Issue #1: I'm seeing lots of resets in the logs for different drives and different exceptions. Sometimes on idle drives, but mostly on those being accessed. Sometimes I can see couple exceptions in a row, but sometimes I don't see any for hours. These are just example exceptions, but I believe I've seen others as well: ata1: failed to read log page 10h (errno=-2) ata1.00: exception Emask 0x1 SAct 0x3 SErr 0x0 action 0x0 ata1.00: irq_stat 0x00060002, device error via SDB FIS ata1.00: cmd 60/80:00:bf:00:00/00:00:00:00:00/40 tag 0 cdb 0x0 data 65536 in res 40/00:00:2f:60:38/00:00:3a:00:00/e0 Emask 0x1 (device error) ata1.00: cmd 60/80:08:3f:00:00/00:00:00:00:00/40 tag 1 cdb 0x0 data 65536 in res 40/00:00:2f:60:38/00:00:3a:00:00/e0 Emask 0x1 (device error) ata1.00: configured for UDMA/100 ata1: EH complete sd 0:0:0:0: [sda] 976773168 512-byte hardware sectors (500108 MB) sd 0:0:0:0: [sda] Write Protect is off sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA ata12: exception Emask 0x10 SAct 0x0 SErr 0x80000 action 0x2 frozen ata12: irq_stat 0x01100010, PHY RDY changed ata12: soft resetting port ata12: softreset failed (timeout) ata12: hard resetting port ata12: SATA link up 3.0 Gbps (SStatus 123 SControl 300) ata12.00: configured for UDMA/100 ata12: EH complete sd 11:0:0:0: [sdj] 976773168 512-byte hardware sectors (500108 MB) sd 11:0:0:0: [sdj] Write Protect is off sd 11:0:0:0: [sdj] Mode Sense: 00 3a 00 00 sd 11:0:0:0: [sdj] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA I'm not sure how critical are those. The side effect of those resets is loosing my standby timeout settings. But I'm rather worried about drives operating optimally and the integrity of my data. Therefore any failure or exception message in the logs is considered bad and means something is wrong and needs attention. Please help me understand/resolve those exceptions. Issue #2: I am also having a performance issue with sata_sil24. I can read data at speeds up to 30 MB/s but write only at speeds around 15 MB/s. When I used Supermicro 8-port sata_mv card, I was able to get speeds at around 40-50 MB/s. Unfortunatelly, sata_mv was not stable at that time and I had to replace it with what was claimed to be the most supported SATA2 chipset under Linux - sata_sil24... I bet the problem is with my setup, but I cannot figure out where or how to fix it. "hdparm -t" reports speeds in the area of 60-80 MB/s though. What I find strange is that the host controller is only recognized as UDMA/100 and all the drives even though they are UDMA/133 configured for UDMA/100. Another strange thing is that all the disks are configured for 16-bit IO_support and cannot be changed to 32-bit: /dev/sda: IO_support = 0 (default 16-bit) readonly = 0 (off) readahead = 256 (on) geometry = 60801/255/63, sectors = 976773168, start = 0 And one more thing - both Maxtor drives have their write cache disabled by default, unlike Seagate drives. Should I be worried about it? The bootup sequence and lspci dump are attached. Please note there is HPT374 2-channel IDE RAID device in the logs, which runs a small RAID5 array, but I tried w/o it before and had same issues. I'd really appreciate if anybody can help me resolve my problems. Thanks in advance! Regards, Denys
Linux version 2.6.23.9 (root@gandalf) (gcc version 3.4.6 (Gentoo 3.4.6-r2, ssp-3.4.6-1.0, pie-8.7.10)) #1 SMP Wed Dec 5 13:18:48 EST 2007 BIOS-provided physical RAM map: BIOS-e820: 0000000000000000 - 0000000000096c00 (usable) BIOS-e820: 0000000000096c00 - 00000000000a0000 (reserved) BIOS-e820: 00000000000ce000 - 0000000000100000 (reserved) BIOS-e820: 0000000000100000 - 000000003fef0000 (usable) BIOS-e820: 000000003fef0000 - 000000003feff000 (ACPI data) BIOS-e820: 000000003feff000 - 000000003ff00000 (ACPI NVS) BIOS-e820: 000000003ff00000 - 000000003ff80000 (usable) BIOS-e820: 000000003ff80000 - 0000000040000000 (reserved) BIOS-e820: 00000000fec00000 - 00000000fec04000 (reserved) BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved) BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved) 127MB HIGHMEM available. 896MB LOWMEM available. found SMP MP-table at 000f7170 Entering add_active_range(0, 0, 262016) 0 entries of 256 used Zone PFN ranges: DMA 0 -> 4096 Normal 4096 -> 229376 HighMem 229376 -> 262016 Movable zone start PFN for each node early_node_map[1] active PFN ranges 0: 0 -> 262016 On node 0 totalpages: 262016 DMA zone: 32 pages used for memmap DMA zone: 0 pages reserved DMA zone: 4064 pages, LIFO batch:0 Normal zone: 1760 pages used for memmap Normal zone: 223520 pages, LIFO batch:31 HighMem zone: 255 pages used for memmap HighMem zone: 32385 pages, LIFO batch:7 Movable zone: 0 pages used for memmap DMI 2.3 present. ACPI: RSDP 000F7100, 0014 (r0 PTLTD ) ACPI: RSDT 3FEFCF28, 002C (r1 PTLTD RSDT 6040000 LTP 0) ACPI: FACP 3FEFEF2E, 0074 (r1 AMD TECATE 6040000 PTL F4240) ACPI: DSDT 3FEFCF54, 1FDA (r1 AMD AMDACPI 6040000 MSFT 100000D) ACPI: FACS 3FEFFFC0, 0040 ACPI: APIC 3FEFEFA2, 005E (r1 PTLTD APIC 6040000 LTP 0) ACPI: PM-Timer IO Port: 0x8008 ACPI: Local APIC address 0xfee00000 ACPI: LAPIC (acpi_id[0x00] lapic_id[0x01] enabled) Processor #1 6:6 APIC version 16 ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled) Processor #0 6:6 APIC version 16 ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1]) ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1]) ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0]) IOAPIC[0]: apic_id 2, version 17, address 0xfec00000, GSI 0-23 ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 high edge) ACPI: IRQ0 used by override. ACPI: IRQ2 used by override. ACPI: IRQ9 used by override. Enabling APIC mode: Flat. Using 1 I/O APICs Using ACPI (MADT) for SMP configuration information Allocating PCI resources starting at 50000000 (gap: 40000000:bec00000) Built 1 zonelists in Zone order. Total pages: 259969 Kernel command line: root=/dev/hda4 mapped APIC to ffffb000 (fee00000) mapped IOAPIC to ffffa000 (fec00000) Enabling fast FPU save and restore... done. Enabling unmasked SIMD FPU exception support... done. Initializing CPU#0 PID hash table entries: 4096 (order: 12, 16384 bytes) Detected 1600.106 MHz processor. Console: colour VGA+ 80x25 console [tty0] enabled Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) Memory: 1031468k/1048064k available (4703k kernel code, 15928k reserved, 1492k data, 228k init, 130496k highmem) virtual kernel memory layout: fixmap : 0xfff9b000 - 0xfffff000 ( 400 kB) pkmap : 0xff800000 - 0xffc00000 (4096 kB) vmalloc : 0xf8800000 - 0xff7fe000 ( 111 MB) lowmem : 0xc0000000 - 0xf8000000 ( 896 MB) .init : 0xc0716000 - 0xc074f000 ( 228 kB) .data : 0xc0597fe0 - 0xc070d138 (1492 kB) .text : 0xc0100000 - 0xc0597fe0 (4703 kB) Checking if this processor honours the WP bit even in supervisor mode... Ok. SLUB: Genslabs=22, HWalign=32, Order=0-1, MinObjects=4, CPUs=2, Nodes=1 Calibrating delay using timer specific routine.. 3203.64 BogoMIPS (lpj=6407286) Mount-cache hash table entries: 512 CPU: After generic identify, caps: 0383fbff c1cbfbff 00000000 00000000 00000000 00000000 00000000 00000000 CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) CPU: L2 Cache: 256K (64 bytes/line) CPU: After all inits, caps: 0383fbff c1cbfbff 00000000 00000420 00000000 00000000 00000000 00000000 Intel machine check architecture supported. Intel machine check reporting enabled on CPU#0. Compat vDSO mapped to ffffe000. Checking 'hlt' instruction... OK. SMP alternatives: switching to UP code ACPI: Core revision 20070126 CPU0: AMD Athlon(tm) MP 1900+ stepping 02 SMP alternatives: switching to SMP code Booting processor 1/0 eip 3000 Initializing CPU#1 Calibrating delay using timer specific routine.. 3200.61 BogoMIPS (lpj=6401239) CPU: After generic identify, caps: 0383fbff c1cbfbff 00000000 00000000 00000000 00000000 00000000 00000000 CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) CPU: L2 Cache: 256K (64 bytes/line) CPU: After all inits, caps: 0383fbff c1cbfbff 00000000 00000420 00000000 00000000 00000000 00000000 Intel machine check architecture supported. Intel machine check reporting enabled on CPU#1. CPU1: AMD Athlon(tm) Processor stepping 02 Total of 2 processors activated (6404.26 BogoMIPS). ENABLING IO-APIC IRQs ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=0 pin2=0 Brought up 2 CPUs xor: automatically using best checksumming function: pIII_sse pIII_sse : 4311.000 MB/sec xor: using function: pIII_sse (4311.000 MB/sec) NET: Registered protocol family 16 ACPI: bus type pci registered PCI: PCI BIOS revision 2.10 entry at 0xfd7d0, last bus=2 PCI: Using configuration type 1 Setting up standard PCI resources mtrr: your CPUs had inconsistent fixed MTRR settings mtrr: probably your BIOS does not setup all CPUs. mtrr: corrected configuration. ACPI: EC: Look up EC in DSDT ACPI: Interpreter enabled ACPI: (supports S0 S1 S5) ACPI: Using IOAPIC for interrupt routing ACPI: PCI Root Bridge [PCI0] (0000:00) ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGP_._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.OP2P._PRT] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 *5 10 11) ACPI: PCI Interrupt Link [LNKB] (IRQs 3 5 10 *11) ACPI: PCI Interrupt Link [LNKC] (IRQs *3 5 10 11) ACPI: PCI Interrupt Link [LNKD] (IRQs 3 5 *10 11) Linux Plug and Play Support v0.97 (c) Adam Belay pnp: PnP ACPI init ACPI: bus type pnp registered pnp: PnP ACPI: found 9 devices ACPI: ACPI bus type pnp unregistered SCSI subsystem initialized libata version 2.21 loaded. usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb PCI: Using ACPI for IRQ routing PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report pnp: 00:00: iomem range 0xfffc0000-0xffffffff could not be reserved pnp: 00:00: iomem range 0xffc00000-0xfff7ffff has been reserved pnp: 00:00: iomem range 0x0-0x9ffff could not be reserved pnp: 00:00: iomem range 0x100000-0x3fffffff could not be reserved pnp: 00:06: ioport range 0x4d0-0x4d1 has been reserved PCI: Bridge: 0000:00:01.0 IO window: disabled. MEM window: f8000000-fbffffff PREFETCH window: 50000000-500fffff PCI: Bridge: 0000:00:10.0 IO window: 2000-2fff MEM window: fc000000-fc0fffff PREFETCH window: 50100000-502fffff NET: Registered protocol family 2 Time: acpi_pm clocksource has been installed. IP route cache hash table entries: 32768 (order: 5, 131072 bytes) TCP established hash table entries: 131072 (order: 8, 1572864 bytes) TCP bind hash table entries: 65536 (order: 7, 524288 bytes) TCP: Hash tables configured (established 131072 bind 65536) TCP reno registered Machine check exception polling timer started. audit: initializing netlink socket (disabled) audit(1203293519.376:1): initialized highmem bounce pool size: 64 pages Installing knfsd (copyright (C) 1996 okir@xxxxxxxxxxxx). NTFS driver 2.1.28 [Flags: R/W]. SGI XFS with large block numbers, no debug enabled async_tx: api initialized (sync-only) io scheduler noop registered io scheduler anticipatory registered (default) io scheduler deadline registered io scheduler cfq registered BIOS failed to enable PCI standards compliance, fixing this error. Boot video device is 0000:01:05.0 input: Power Button (FF) as /class/input/input0 ACPI: Power Button (FF) [PWRF] input: Sleep Button (FF) as /class/input/input1 ACPI: Sleep Button (FF) [SLPF] input: Power Button (CM) as /class/input/input2 ACPI: Power Button (CM) [PWRB] lp: driver loaded but no devices found Linux agpgart interface v0.102 agpgart: Detected AMD 760MP chipset agpgart: AGP aperture is 32M @ 0x0 [drm] Initialized drm 1.1.0 20060810 Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled Intel(R) PRO/1000 Network Driver - version 7.3.20-k2 Copyright (c) 1999-2006 Intel Corporation. ACPI: PCI Interrupt 0000:02:04.0[A] -> GSI 16 (level, low) -> IRQ 16 e1000: 0000:02:04.0: e1000_probe: (PCI:33MHz:32-bit) 00:07:e9:0f:54:22 e1000: eth0: e1000_probe: Intel(R) PRO/1000 Network Connection ACPI: PCI Interrupt 0000:02:08.0[A] -> GSI 19 (level, low) -> IRQ 17 3c59x: Donald Becker and others. 0000:02:08.0: 3Com PCI 3c905C Tornado at f8826c00. Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx AMD7441: IDE controller at PCI slot 0000:00:07.1 AMD7441: chipset revision 4 AMD7441: not 100% native mode: will probe irqs later AMD7441: 0000:00:07.1 (rev 04) UDMA100 controller ide0: BM-DMA at 0xf000-0xf007, BIOS settings: hda:DMA, hdb:DMA ide1: BM-DMA at 0xf008-0xf00f, BIOS settings: hdc:DMA, hdd:pio Probing IDE interface ide0... hda: WDC WD300BB-00AUA1, ATA DISK drive hdb: PIONEER DVD-RW DVR-112D, ATAPI CD/DVD-ROM drive hda: selected mode 0x45 hdb: selected mode 0x44 ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 Probing IDE interface ide1... hdc: WDC WD800JB-00CRA1, ATA DISK drive hdc: selected mode 0x45 ide1 at 0x170-0x177,0x376 on irq 15 hda: max request size: 128KiB hda: 58633344 sectors (30020 MB) w/2048KiB Cache, CHS=58168/16/63, UDMA(100) hda: cache flushes not supported hda: hda1 hda2 hda3 hda4 hdc: max request size: 128KiB hdc: 156301488 sectors (80026 MB) w/8192KiB Cache, CHS=65535/16/63, UDMA(100) hdc: cache flushes not supported hdc: hdc1 hdb: ATAPI 40X DVD-ROM DVD-R CD-R/RW drive, 2000kB Cache, UDMA(66) Uniform CD-ROM driver Revision: 3.20 sata_sil24 0000:02:05.0: version 1.0 ACPI: PCI Interrupt 0000:02:05.0[A] -> GSI 17 (level, low) -> IRQ 18 scsi0 : sata_sil24 scsi1 : sata_sil24 scsi2 : sata_sil24 scsi3 : sata_sil24 ata1: SATA max UDMA/100 cmd 0xf8830000 ctl 0x00000000 bmdma 0x00000000 irq 18 ata2: SATA max UDMA/100 cmd 0xf8832000 ctl 0x00000000 bmdma 0x00000000 irq 18 ata3: SATA max UDMA/100 cmd 0xf8834000 ctl 0x00000000 bmdma 0x00000000 irq 18 ata4: SATA max UDMA/100 cmd 0xf8836000 ctl 0x00000000 bmdma 0x00000000 irq 18 ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) ata1.00: ATA-7: Maxtor 7H500F0, HA431DN0, max UDMA/133 ata1.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 31/32) ata1.00: configured for UDMA/100 ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300) ata2.00: ATA-7: ST3500630AS, 3.AAE, max UDMA/133 ata2.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 31/32) ata2.00: configured for UDMA/100 ata3: SATA link down (SStatus 0 SControl 300) ata4: SATA link down (SStatus 0 SControl 300) scsi 0:0:0:0: Direct-Access ATA Maxtor 7H500F0 HA43 PQ: 0 ANSI: 5 sd 0:0:0:0: [sda] 976773168 512-byte hardware sectors (500108 MB) sd 0:0:0:0: [sda] Write Protect is off sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA sd 0:0:0:0: [sda] 976773168 512-byte hardware sectors (500108 MB) sd 0:0:0:0: [sda] Write Protect is off sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA sda: sda1 sd 0:0:0:0: [sda] Attached SCSI disk sd 0:0:0:0: Attached scsi generic sg0 type 0 scsi 1:0:0:0: Direct-Access ATA ST3500630AS 3.AA PQ: 0 ANSI: 5 sd 1:0:0:0: [sdb] 976773168 512-byte hardware sectors (500108 MB) sd 1:0:0:0: [sdb] Write Protect is off sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00 sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sd 1:0:0:0: [sdb] 976773168 512-byte hardware sectors (500108 MB) sd 1:0:0:0: [sdb] Write Protect is off sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00 sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sdb: sdb1 sd 1:0:0:0: [sdb] Attached SCSI disk sd 1:0:0:0: Attached scsi generic sg1 type 0 ACPI: PCI Interrupt 0000:02:06.0[A] -> GSI 18 (level, low) -> IRQ 19 scsi4 : sata_sil24 scsi5 : sata_sil24 scsi6 : sata_sil24 scsi7 : sata_sil24 ata5: SATA max UDMA/100 cmd 0xf8870000 ctl 0x00000000 bmdma 0x00000000 irq 19 ata6: SATA max UDMA/100 cmd 0xf8872000 ctl 0x00000000 bmdma 0x00000000 irq 19 ata7: SATA max UDMA/100 cmd 0xf8874000 ctl 0x00000000 bmdma 0x00000000 irq 19 ata8: SATA max UDMA/100 cmd 0xf8876000 ctl 0x00000000 bmdma 0x00000000 irq 19 ata5: SATA link up 3.0 Gbps (SStatus 123 SControl 300) ata5.00: ATA-7: ST3500630AS, 3.AAE, max UDMA/133 ata5.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 31/32) ata5.00: configured for UDMA/100 ata6: SATA link up 3.0 Gbps (SStatus 123 SControl 300) ata6.00: ATA-7: Maxtor 7H500F0, HA431DN0, max UDMA/133 ata6.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 31/32) ata6.00: configured for UDMA/100 ata7: SATA link up 3.0 Gbps (SStatus 123 SControl 300) ata7.00: ATA-7: ST3500641AS, 3.AAH, max UDMA/133 ata7.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 31/32) ata7.00: configured for UDMA/100 ata8: SATA link up 3.0 Gbps (SStatus 123 SControl 300) ata8.00: ATA-7: ST3500641AS, 3.AAJ, max UDMA/133 ata8.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 31/32) ata8.00: configured for UDMA/100 scsi 4:0:0:0: Direct-Access ATA ST3500630AS 3.AA PQ: 0 ANSI: 5 sd 4:0:0:0: [sdc] 976773168 512-byte hardware sectors (500108 MB) sd 4:0:0:0: [sdc] Write Protect is off sd 4:0:0:0: [sdc] Mode Sense: 00 3a 00 00 sd 4:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sd 4:0:0:0: [sdc] 976773168 512-byte hardware sectors (500108 MB) sd 4:0:0:0: [sdc] Write Protect is off sd 4:0:0:0: [sdc] Mode Sense: 00 3a 00 00 sd 4:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sdc: sdc1 sd 4:0:0:0: [sdc] Attached SCSI disk sd 4:0:0:0: Attached scsi generic sg2 type 0 scsi 5:0:0:0: Direct-Access ATA Maxtor 7H500F0 HA43 PQ: 0 ANSI: 5 sd 5:0:0:0: [sdd] 976773168 512-byte hardware sectors (500108 MB) sd 5:0:0:0: [sdd] Write Protect is off sd 5:0:0:0: [sdd] Mode Sense: 00 3a 00 00 sd 5:0:0:0: [sdd] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA sd 5:0:0:0: [sdd] 976773168 512-byte hardware sectors (500108 MB) sd 5:0:0:0: [sdd] Write Protect is off sd 5:0:0:0: [sdd] Mode Sense: 00 3a 00 00 sd 5:0:0:0: [sdd] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA sdd: sdd1 sd 5:0:0:0: [sdd] Attached SCSI disk sd 5:0:0:0: Attached scsi generic sg3 type 0 scsi 6:0:0:0: Direct-Access ATA ST3500641AS 3.AA PQ: 0 ANSI: 5 sd 6:0:0:0: [sde] 976773168 512-byte hardware sectors (500108 MB) sd 6:0:0:0: [sde] Write Protect is off sd 6:0:0:0: [sde] Mode Sense: 00 3a 00 00 sd 6:0:0:0: [sde] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sd 6:0:0:0: [sde] 976773168 512-byte hardware sectors (500108 MB) sd 6:0:0:0: [sde] Write Protect is off sd 6:0:0:0: [sde] Mode Sense: 00 3a 00 00 sd 6:0:0:0: [sde] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sde: sde1 sd 6:0:0:0: [sde] Attached SCSI disk sd 6:0:0:0: Attached scsi generic sg4 type 0 scsi 7:0:0:0: Direct-Access ATA ST3500641AS 3.AA PQ: 0 ANSI: 5 sd 7:0:0:0: [sdf] 976773168 512-byte hardware sectors (500108 MB) sd 7:0:0:0: [sdf] Write Protect is off sd 7:0:0:0: [sdf] Mode Sense: 00 3a 00 00 sd 7:0:0:0: [sdf] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sd 7:0:0:0: [sdf] 976773168 512-byte hardware sectors (500108 MB) sd 7:0:0:0: [sdf] Write Protect is off sd 7:0:0:0: [sdf] Mode Sense: 00 3a 00 00 sd 7:0:0:0: [sdf] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sdf: sdf1 sd 7:0:0:0: [sdf] Attached SCSI disk sd 7:0:0:0: Attached scsi generic sg5 type 0 ACPI: PCI Interrupt 0000:02:07.0[A] -> GSI 19 (level, low) -> IRQ 17 scsi8 : sata_sil24 scsi9 : sata_sil24 scsi10 : sata_sil24 scsi11 : sata_sil24 ata9: SATA max UDMA/100 cmd 0xf8880000 ctl 0x00000000 bmdma 0x00000000 irq 17 ata10: SATA max UDMA/100 cmd 0xf8882000 ctl 0x00000000 bmdma 0x00000000 irq 17 ata11: SATA max UDMA/100 cmd 0xf8884000 ctl 0x00000000 bmdma 0x00000000 irq 17 ata12: SATA max UDMA/100 cmd 0xf8886000 ctl 0x00000000 bmdma 0x00000000 irq 17 ata9: SATA link up 3.0 Gbps (SStatus 123 SControl 300) ata9.00: ATA-7: ST3500630AS, 3.AAK, max UDMA/133 ata9.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 31/32) ata9.00: configured for UDMA/100 ata10: SATA link up 3.0 Gbps (SStatus 123 SControl 300) ata10.00: ATA-7: ST3500630AS, 3.AAK, max UDMA/133 ata10.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 31/32) ata10.00: configured for UDMA/100 ata11: SATA link up 3.0 Gbps (SStatus 123 SControl 300) ata11.00: ATA-7: ST3500641AS, 3.AAJ, max UDMA/133 ata11.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 31/32) ata11.00: configured for UDMA/100 ata12: SATA link up 3.0 Gbps (SStatus 123 SControl 300) ata12.00: ATA-7: ST3500630AS, 3.AAK, max UDMA/133 ata12.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 31/32) ata12.00: configured for UDMA/100 scsi 8:0:0:0: Direct-Access ATA ST3500630AS 3.AA PQ: 0 ANSI: 5 sd 8:0:0:0: [sdg] 976773168 512-byte hardware sectors (500108 MB) sd 8:0:0:0: [sdg] Write Protect is off sd 8:0:0:0: [sdg] Mode Sense: 00 3a 00 00 sd 8:0:0:0: [sdg] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sd 8:0:0:0: [sdg] 976773168 512-byte hardware sectors (500108 MB) sd 8:0:0:0: [sdg] Write Protect is off sd 8:0:0:0: [sdg] Mode Sense: 00 3a 00 00 sd 8:0:0:0: [sdg] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sdg: sdg1 sd 8:0:0:0: [sdg] Attached SCSI disk sd 8:0:0:0: Attached scsi generic sg6 type 0 scsi 9:0:0:0: Direct-Access ATA ST3500630AS 3.AA PQ: 0 ANSI: 5 sd 9:0:0:0: [sdh] 976773168 512-byte hardware sectors (500108 MB) sd 9:0:0:0: [sdh] Write Protect is off sd 9:0:0:0: [sdh] Mode Sense: 00 3a 00 00 sd 9:0:0:0: [sdh] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sd 9:0:0:0: [sdh] 976773168 512-byte hardware sectors (500108 MB) sd 9:0:0:0: [sdh] Write Protect is off sd 9:0:0:0: [sdh] Mode Sense: 00 3a 00 00 sd 9:0:0:0: [sdh] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sdh: sdh1 sd 9:0:0:0: [sdh] Attached SCSI disk sd 9:0:0:0: Attached scsi generic sg7 type 0 scsi 10:0:0:0: Direct-Access ATA ST3500641AS 3.AA PQ: 0 ANSI: 5 sd 10:0:0:0: [sdi] 976773168 512-byte hardware sectors (500108 MB) sd 10:0:0:0: [sdi] Write Protect is off sd 10:0:0:0: [sdi] Mode Sense: 00 3a 00 00 sd 10:0:0:0: [sdi] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sd 10:0:0:0: [sdi] 976773168 512-byte hardware sectors (500108 MB) sd 10:0:0:0: [sdi] Write Protect is off sd 10:0:0:0: [sdi] Mode Sense: 00 3a 00 00 sd 10:0:0:0: [sdi] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sdi: sdi1 sd 10:0:0:0: [sdi] Attached SCSI disk sd 10:0:0:0: Attached scsi generic sg8 type 0 scsi 11:0:0:0: Direct-Access ATA ST3500630AS 3.AA PQ: 0 ANSI: 5 sd 11:0:0:0: [sdj] 976773168 512-byte hardware sectors (500108 MB) sd 11:0:0:0: [sdj] Write Protect is off sd 11:0:0:0: [sdj] Mode Sense: 00 3a 00 00 sd 11:0:0:0: [sdj] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sd 11:0:0:0: [sdj] 976773168 512-byte hardware sectors (500108 MB) sd 11:0:0:0: [sdj] Write Protect is off sd 11:0:0:0: [sdj] Mode Sense: 00 3a 00 00 sd 11:0:0:0: [sdj] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sdj: sdj1 sd 11:0:0:0: [sdj] Attached SCSI disk sd 11:0:0:0: Attached scsi generic sg9 type 0 ieee1394: raw1394: /dev/raw1394 device initialized usbmon: debugfs is not available ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver ACPI: PCI Interrupt 0000:02:00.0[D] -> GSI 19 (level, low) -> IRQ 17 ohci_hcd 0000:02:00.0: OHCI Host Controller ohci_hcd 0000:02:00.0: new USB bus registered, assigned bus number 1 ohci_hcd 0000:02:00.0: irq 17, io mem 0xfc018000 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 4 ports detected usb 1-4: new low speed USB device using ohci_hcd and address 2 usb 1-4: device descriptor read/64, error -62 usb 1-4: device descriptor read/64, error -62 usb 1-4: new low speed USB device using ohci_hcd and address 3 usb 1-4: device descriptor read/64, error -62 usb 1-4: device descriptor read/64, error -62 usb 1-4: new low speed USB device using ohci_hcd and address 4 usb 1-4: device not accepting address 4, error -62 usb 1-4: new low speed USB device using ohci_hcd and address 5 usb 1-4: device not accepting address 5, error -62 usbcore: registered new interface driver usblp Initializing USB Mass Storage driver... usbcore: registered new interface driver usb-storage USB Mass Storage support registered. PNP: PS/2 Controller [PNP0303:PS2K] at 0x60,0x64 irq 1 PNP: PS/2 appears to have AUX port disabled, if this is incorrect please boot with i8042.nopnp serio: i8042 KBD port at 0x60,0x64 irq 1 mice: PS/2 mouse device common for all mice input: AT Translated Set 2 keyboard as /class/input/input3 md: raid0 personality registered for level 0 md: raid1 personality registered for level 1 md: raid10 personality registered for level 10 raid6: int32x1 658 MB/s raid6: int32x2 853 MB/s raid6: int32x4 549 MB/s raid6: int32x8 508 MB/s raid6: mmxx1 1311 MB/s raid6: mmxx2 2258 MB/s raid6: sse1x1 468 MB/s raid6: sse1x2 936 MB/s raid6: using algorithm sse1x2 (936 MB/s) md: raid6 personality registered for level 6 md: raid5 personality registered for level 5 md: raid4 personality registered for level 4 device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised: dm-devel@xxxxxxxxxx usbcore: registered new interface driver usbhid drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver Advanced Linux Sound Architecture Driver Version 1.0.14 (Fri Jul 20 09:12:58 2007 UTC). ALSA device list: No soundcards found. Netfilter messages via NETLINK v0.30. nf_conntrack version 0.5.0 (16384 buckets, 65536 max) ctnetlink v0.93: registering with nfnetlink. ip_tables: (C) 2000-2006 Netfilter Core Team ClusterIP Version 0.8 loaded successfully arp_tables: (C) 2002 David S. Miller TCP cubic registered NET: Registered protocol family 1 NET: Registered protocol family 17 Starting balanced_irq Using IPI No-Shortcut mode md: Autodetecting RAID arrays. md: autorun ... md: ... autorun DONE. ReiserFS: hda4: found reiserfs format "3.6" with standard journal ReiserFS: hda4: using ordered data mode ReiserFS: hda4: journal params: device hda4, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30 ReiserFS: hda4: checking transaction log (hda4) ReiserFS: hda4: Using r5 hash to sort names VFS: Mounted root (reiserfs filesystem) readonly. Freeing unused kernel memory: 228k freed AMD768 RNG detected Real Time Clock Driver v1.12ac floppy0: no floppy controllers found hpt374: module license 'Proprietary' taints kernel. HPT374 UDMA/ATA133 RAID Controller driver Version 2.17, Compiled Dec 9 2007 18:19:24 RAID5 write-back enabled ACPI: PCI Interrupt 0000:00:09.0[A] -> GSI 21 (level, low) -> IRQ 20 ACPI: PCI Interrupt 0000:00:09.1[A] -> GSI 21 (level, low) -> IRQ 20 scsi12 : hpt374 scsi 12:0:0:0: Direct-Access HPT3xx RAID 5 Array 3.00 PQ: 0 ANSI: 0 sd 12:0:0:0: [sdk] 976793600 512-byte hardware sectors (500118 MB) sd 12:0:0:0: [sdk] Write Protect is off sd 12:0:0:0: [sdk] Mode Sense: 2f 00 00 00 sd 12:0:0:0: [sdk] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sd 12:0:0:0: [sdk] 976793600 512-byte hardware sectors (500118 MB) sd 12:0:0:0: [sdk] Write Protect is off sd 12:0:0:0: [sdk] Mode Sense: 2f 00 00 00 sd 12:0:0:0: [sdk] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sdk: sdk1 sd 12:0:0:0: [sdk] Attached SCSI disk sd 12:0:0:0: Attached scsi generic sg10 type 0 w83781d 0-002c: The W83627HF chip is better supported by the w83627hf driver, support will be dropped from the w83781d driver soon aufs 20071203 kjournald starting. Commit interval 5 seconds EXT3 FS on hda3, internal journal EXT3-fs: mounted filesystem with ordered data mode. kjournald starting. Commit interval 5 seconds EXT3-fs warning: maximal mount count reached, running e2fsck is recommended EXT3 FS on hdc1, internal journal EXT3-fs: mounted filesystem with ordered data mode. XFS mounting filesystem sdk1 Ending clean XFS mount for filesystem: sdk1 XFS mounting filesystem sdj1 Ending clean XFS mount for filesystem: sdj1 XFS mounting filesystem sdc1 Ending clean XFS mount for filesystem: sdc1 XFS mounting filesystem sdi1 Ending clean XFS mount for filesystem: sdi1 XFS mounting filesystem sdh1 Ending clean XFS mount for filesystem: sdh1 XFS mounting filesystem sdg1 Ending clean XFS mount for filesystem: sdg1 XFS mounting filesystem sdf1 Ending clean XFS mount for filesystem: sdf1 XFS mounting filesystem sda1 Ending clean XFS mount for filesystem: sda1 XFS mounting filesystem sdb1 Ending clean XFS mount for filesystem: sdb1 XFS mounting filesystem sde1 Ending clean XFS mount for filesystem: sde1 XFS mounting filesystem sdd1 Ending clean XFS mount for filesystem: sdd1 Adding 530136k swap on /dev/hda2. Priority:-1 extents:1 across:530136k hda: selected mode 0x45 hdb: selected mode 0x44 hdc: selected mode 0x45 e1000: eth0: e1000_watchdog: NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX eth1: setting half-duplex. NFSD: Using /var/lib/nfs/v4recovery as the NFSv4 state recovery directory NFSD: starting 90-second grace period w83627hf: Found W83627HF chip at 0xc00 PPP generic driver version 2.4.2 PPP BSD Compression module registered
00:00.0 Host bridge: Advanced Micro Devices [AMD] AMD-760 MP [IGD4-2P] System Controller (rev 11) Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx- Latency: 32 Region 0: Memory at <unassigned> (32-bit, prefetchable) Region 1: Memory at fc300000 (32-bit, prefetchable) [size=4K] Region 2: I/O ports at 1810 [disabled] [size=4] Capabilities: [a0] AGP version 2.0 Status: RQ=16 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans- 64bit- FW- AGP3- Rate=x1,x2 Command: RQ=1 ArqSz=0 Cal=0 SBA+ AGP+ GART64- 64bit- FW- Rate=<none> Kernel driver in use: agpgart-amdk7 00:01.0 PCI bridge: Advanced Micro Devices [AMD] AMD-760 MP [IGD4-2P] AGP Bridge (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 99 Bus: primary=00, secondary=01, subordinate=01, sec-latency=64 I/O behind bridge: 0000f000-00000fff Memory behind bridge: f8000000-fbffffff Prefetchable memory behind bridge: 50000000-500fffff Secondary status: 66MHz+ FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR- BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- 00:07.0 ISA bridge: Advanced Micro Devices [AMD] AMD-768 [Opus] ISA (rev 05) Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 00:07.1 IDE interface: Advanced Micro Devices [AMD] AMD-768 [Opus] IDE (rev 04) (prog-if 8a [Master SecP PriP]) Subsystem: Advanced Micro Devices [AMD] AMD-768 [Opus] IDE Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Region 0: [virtual] Memory at 000001f0 (32-bit, non-prefetchable) [disabled] [size=8] Region 1: [virtual] Memory at 000003f0 (type 3, non-prefetchable) [disabled] [size=1] Region 2: [virtual] Memory at 00000170 (32-bit, non-prefetchable) [disabled] [size=8] Region 3: [virtual] Memory at 00000370 (type 3, non-prefetchable) [disabled] [size=1] Region 4: I/O ports at f000 [size=16] Kernel driver in use: AMD_IDE 00:07.3 Bridge: Advanced Micro Devices [AMD] AMD-768 [Opus] ACPI (rev 03) Subsystem: Advanced Micro Devices [AMD] AMD-768 [Opus] ACPI Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Kernel driver in use: amd756_smbus Kernel modules: i2c-amd756, amd-rng 00:09.0 RAID bus controller: Triones Technologies, Inc. HPT374 (rev 07) Subsystem: Triones Technologies, Inc. Unknown device 0001 Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 64 (2000ns min, 2000ns max) Interrupt: pin A routed to IRQ 20 Region 0: I/O ports at 1828 [size=8] Region 1: I/O ports at 1820 [size=4] Region 2: I/O ports at 1818 [size=8] Region 3: I/O ports at 1814 [size=4] Region 4: I/O ports at 1000 [size=256] [virtual] Expansion ROM at 50300000 [disabled] [size=128K] Capabilities: [60] Power Management version 2 Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- 00:09.1 RAID bus controller: Triones Technologies, Inc. HPT374 (rev 07) Subsystem: Triones Technologies, Inc. Unknown device 0001 Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 64 (2000ns min, 2000ns max) Interrupt: pin A routed to IRQ 20 Region 0: I/O ports at 1840 [size=8] Region 1: I/O ports at 1838 [size=4] Region 2: I/O ports at 1830 [size=8] Region 3: I/O ports at 1824 [size=4] Region 4: I/O ports at 1400 [size=256] Capabilities: [60] Power Management version 2 Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- 00:10.0 PCI bridge: Advanced Micro Devices [AMD] AMD-768 [Opus] PCI (rev 05) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx- Latency: 64 Bus: primary=00, secondary=02, subordinate=02, sec-latency=168 I/O behind bridge: 00002000-00002fff Memory behind bridge: fc000000-fc0fffff Prefetchable memory behind bridge: 50100000-502fffff Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- <SERR- <PERR- BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- 01:05.0 VGA compatible controller: S3 Inc. 86c368 [Trio 3D/2X] (rev 02) (prog-if 00 [VGA controller]) Subsystem: S3 Inc. Trio3D/2X Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Region 0: Memory at f8000000 (32-bit, non-prefetchable) [size=64M] [virtual] Expansion ROM at 50000000 [disabled] [size=64K] Capabilities: [dc] Power Management version 1 Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Capabilities: [80] AGP version 1.0 Status: RQ=32 Iso- ArqSz=0 Cal=0 SBA- ITACoh- GART64- HTrans- 64bit- FW- AGP3- Rate=x1,x2 Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64- 64bit- FW- Rate=x2 02:00.0 USB Controller: Advanced Micro Devices [AMD] AMD-768 [Opus] USB (rev 07) (prog-if 10 [OHCI]) Subsystem: Advanced Micro Devices [AMD] AMD-768 [Opus] USB Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 64 (20000ns max) Interrupt: pin D routed to IRQ 17 Region 0: Memory at fc018000 (32-bit, non-prefetchable) [size=4K] Kernel driver in use: ohci_hcd 02:04.0 Ethernet controller: Intel Corporation 82540EM Gigabit Ethernet Controller (rev 02) Subsystem: Intel Corporation PRO/1000 MT Desktop Adapter Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 64 (63750ns min), Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 16 Region 0: Memory at fc040000 (32-bit, non-prefetchable) [size=128K] Region 1: Memory at fc020000 (32-bit, non-prefetchable) [size=128K] Region 2: I/O ports at 2080 [size=64] [virtual] Expansion ROM at 50280000 [disabled] [size=128K] Capabilities: [dc] Power Management version 2 Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=1 PME- Capabilities: [e4] PCI-X non-bridge device Command: DPERE- ERO+ RBC=512 OST=1 Status: Dev=00:00.0 64bit- 133MHz- SCD- USC- DC=simple DMMRBC=2048 DMOST=1 DMCRS=16 RSCEM- 266MHz- 533MHz- Capabilities: [f0] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable- Address: 0000000000000000 Data: 0000 Kernel driver in use: e1000 02:05.0 RAID bus controller: Silicon Image, Inc. SiI 3124 PCI-X Serial ATA Controller (rev 02) Subsystem: Silicon Image, Inc. Unknown device 7124 Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV+ VGASnoop- ParErr- Stepping+ SERR- FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 64, Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 18 Region 0: Memory at fc019000 (64-bit, non-prefetchable) [size=128] Region 2: Memory at fc000000 (64-bit, non-prefetchable) [size=32K] Region 4: I/O ports at 20c0 [size=16] [virtual] Expansion ROM at 50100000 [disabled] [size=512K] Capabilities: [64] Power Management version 2 Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=1 PME- Capabilities: [40] PCI-X non-bridge device Command: DPERE- ERO+ RBC=512 OST=12 Status: Dev=ff:1f.0 64bit+ 133MHz+ SCD- USC- DC=simple DMMRBC=2048 DMOST=12 DMCRS=128 RSCEM- 266MHz- 533MHz- Capabilities: [54] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable- Address: 0000000000000000 Data: 0000 Kernel driver in use: sata_sil24 02:06.0 RAID bus controller: Silicon Image, Inc. SiI 3124 PCI-X Serial ATA Controller (rev 02) Subsystem: Silicon Image, Inc. Unknown device 7124 Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV+ VGASnoop- ParErr- Stepping+ SERR- FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 64, Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 19 Region 0: Memory at fc019400 (64-bit, non-prefetchable) [size=128] Region 2: Memory at fc008000 (64-bit, non-prefetchable) [size=32K] Region 4: I/O ports at 20d0 [size=16] [virtual] Expansion ROM at 50180000 [disabled] [size=512K] Capabilities: [64] Power Management version 2 Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=1 PME- Capabilities: [40] PCI-X non-bridge device Command: DPERE- ERO+ RBC=512 OST=12 Status: Dev=ff:1f.0 64bit+ 133MHz+ SCD- USC- DC=simple DMMRBC=2048 DMOST=12 DMCRS=128 RSCEM- 266MHz- 533MHz- Capabilities: [54] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable- Address: 0000000000000000 Data: 0000 Kernel driver in use: sata_sil24 02:07.0 RAID bus controller: Silicon Image, Inc. SiI 3124 PCI-X Serial ATA Controller (rev 02) Subsystem: Silicon Image, Inc. Unknown device 7124 Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV+ VGASnoop- ParErr- Stepping+ SERR- FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 64, Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 17 Region 0: Memory at fc019800 (64-bit, non-prefetchable) [size=128] Region 2: Memory at fc010000 (64-bit, non-prefetchable) [size=32K] Region 4: I/O ports at 20e0 [size=16] [virtual] Expansion ROM at 50200000 [disabled] [size=512K] Capabilities: [64] Power Management version 2 Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=1 PME- Capabilities: [40] PCI-X non-bridge device Command: DPERE- ERO+ RBC=512 OST=12 Status: Dev=ff:1f.0 64bit+ 133MHz+ SCD- USC- DC=simple DMMRBC=2048 DMOST=12 DMCRS=128 RSCEM- 266MHz- 533MHz- Capabilities: [54] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable- Address: 0000000000000000 Data: 0000 Kernel driver in use: sata_sil24 02:08.0 Ethernet controller: 3Com Corporation 3c905C-TX/TX-M [Tornado] (rev 78) Subsystem: Tyan Computer Tiger MPX S2466 (3C920 Integrated Fast Ethernet Controller) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 80 (2500ns min, 2500ns max), Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 17 Region 0: I/O ports at 2000 [size=128] Region 1: Memory at fc019c00 (32-bit, non-prefetchable) [size=128] [virtual] Expansion ROM at 502a0000 [disabled] [size=128K] Capabilities: [dc] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=2 PME- Kernel driver in use: 3c59x