Please pull from 'upstream-linus' branch of
master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev.git upstream-linus
to receive the following updates:
arch/arm/mach-rpc/riscpc.c | 2 +-
arch/blackfin/mach-bf527/boards/ezkit.c | 2 +-
arch/blackfin/mach-bf533/boards/H8606.c | 2 +-
arch/blackfin/mach-bf533/boards/cm_bf533.c | 2 +-
arch/blackfin/mach-bf533/boards/ezkit.c | 2 +-
arch/blackfin/mach-bf533/boards/stamp.c | 2 +-
arch/blackfin/mach-bf537/boards/cm_bf537.c | 2 +-
arch/blackfin/mach-bf537/boards/generic_board.c | 2 +-
arch/blackfin/mach-bf537/boards/minotaur.c | 2 +-
arch/blackfin/mach-bf537/boards/stamp.c | 2 +-
arch/blackfin/mach-bf561/boards/cm_bf561.c | 2 +-
arch/blackfin/mach-bf561/boards/ezkit.c | 2 +-
arch/sh/boards/landisk/setup.c | 2 +-
arch/sh/boards/lboxre2/setup.c | 2 +-
arch/sh/boards/renesas/r7780rp/setup.c | 2 +-
arch/sh/boards/renesas/rts7751r2d/setup.c | 2 +-
arch/sh/boards/renesas/sdk7780/setup.c | 2 +-
arch/sh/boards/se/7722/setup.c | 2 +-
drivers/ata/ahci.c | 35 +-
drivers/ata/ata_piix.c | 3 +-
drivers/ata/libata-core.c | 2 -
drivers/ata/pata_of_platform.c | 2 +-
drivers/ata/pata_platform.c | 2 +-
drivers/ata/sata_fsl.c | 4 +-
drivers/ata/sata_mv.c | 366 ++++++++++++++++++---
drivers/ata/sata_nv.c | 78 ++++-
drivers/ata/sata_via.c | 2 -
drivers/ide/legacy/ide_platform.c | 2 +-
include/linux/{pata_platform.h => ata_platform.h} | 13 +-
include/linux/libata.h | 2 -
30 files changed, 440 insertions(+), 107 deletions(-)
rename include/linux/{pata_platform.h => ata_platform.h} (75%)
Adrian Bunk (1):
ata_piix.c:piix_init_one() must be __devinit
Alejandro Riveira Fernández (1):
sata_via.c: Remove missleading comment.
Andrew Morton (1):
ata: drivers/ata/sata_mv.c needs dmapool.h
David Milburn (1):
libata-core: unblacklist HITACHI drives
James Bottomley (1):
libata: kill now unused n_iter and fix sata_fsl
Jeff Garzik (1):
Rename: linux/pata_platform.h to linux/ata_platform.h
Robert Hancock (1):
sata_nv: fix ATAPI issues with memory over 4GB (v7)
Saeed Bishara (1):
sata_mv: Support SoC controllers
Tejun Heo (1):
ahci: fix CAP.NP and PI handling
diff --git a/arch/arm/mach-rpc/riscpc.c b/arch/arm/mach-rpc/riscpc.c
index a454451..eca558c 100644
--- a/arch/arm/mach-rpc/riscpc.c
+++ b/arch/arm/mach-rpc/riscpc.c
@@ -17,7 +17,7 @@
#include <linux/sched.h>
#include <linux/device.h>
#include <linux/serial_8250.h>
-#include <linux/pata_platform.h>
+#include <linux/ata_platform.h>
#include <asm/elf.h>
#include <asm/io.h>
diff --git a/arch/blackfin/mach-bf527/boards/ezkit.c b/arch/blackfin/mach-bf527/boards/ezkit.c
index f8c411a..1795aab 100644
--- a/arch/blackfin/mach-bf527/boards/ezkit.c
+++ b/arch/blackfin/mach-bf527/boards/ezkit.c
@@ -37,7 +37,7 @@
#if defined(CONFIG_USB_ISP1362_HCD) || defined(CONFIG_USB_ISP1362_HCD_MODULE)
#include <linux/usb/isp1362.h>
#endif
-#include <linux/pata_platform.h>
+#include <linux/ata_platform.h>
#include <linux/irq.h>
#include <linux/interrupt.h>
#include <linux/usb/sl811.h>
diff --git a/arch/blackfin/mach-bf533/boards/H8606.c b/arch/blackfin/mach-bf533/boards/H8606.c
index a72c7a6..97378b0 100644
--- a/arch/blackfin/mach-bf533/boards/H8606.c
+++ b/arch/blackfin/mach-bf533/boards/H8606.c
@@ -38,7 +38,7 @@
#if defined(CONFIG_USB_ISP1362_HCD) || defined(CONFIG_USB_ISP1362_HCD_MODULE)
#include <linux/usb/isp1362.h>
#endif
-#include <linux/pata_platform.h>
+#include <linux/ata_platform.h>
#include <linux/irq.h>
#include <asm/dma.h>
diff --git a/arch/blackfin/mach-bf533/boards/cm_bf533.c b/arch/blackfin/mach-bf533/boards/cm_bf533.c
index 21df2f3..886f260 100644
--- a/arch/blackfin/mach-bf533/boards/cm_bf533.c
+++ b/arch/blackfin/mach-bf533/boards/cm_bf533.c
@@ -34,7 +34,7 @@
#include <linux/spi/spi.h>
#include <linux/spi/flash.h>
#include <linux/usb/isp1362.h>
-#include <linux/pata_platform.h>
+#include <linux/ata_platform.h>
#include <linux/irq.h>
#include <asm/dma.h>
#include <asm/bfin5xx_spi.h>
diff --git a/arch/blackfin/mach-bf533/boards/ezkit.c b/arch/blackfin/mach-bf533/boards/ezkit.c
index c37dd45..4026c2f 100644
--- a/arch/blackfin/mach-bf533/boards/ezkit.c
+++ b/arch/blackfin/mach-bf533/boards/ezkit.c
@@ -35,7 +35,7 @@
#include <linux/spi/spi.h>
#include <linux/spi/flash.h>
#include <linux/usb/isp1362.h>
-#include <linux/pata_platform.h>
+#include <linux/ata_platform.h>
#include <linux/irq.h>
#include <asm/dma.h>
#include <asm/bfin5xx_spi.h>
diff --git a/arch/blackfin/mach-bf533/boards/stamp.c b/arch/blackfin/mach-bf533/boards/stamp.c
index ac52b04..0185350 100644
--- a/arch/blackfin/mach-bf533/boards/stamp.c
+++ b/arch/blackfin/mach-bf533/boards/stamp.c
@@ -38,7 +38,7 @@
#if defined(CONFIG_USB_ISP1362_HCD) || defined(CONFIG_USB_ISP1362_HCD_MODULE)
#include <linux/usb/isp1362.h>
#endif
-#include <linux/pata_platform.h>
+#include <linux/ata_platform.h>
#include <linux/irq.h>
#include <asm/dma.h>
#include <asm/bfin5xx_spi.h>
diff --git a/arch/blackfin/mach-bf537/boards/cm_bf537.c b/arch/blackfin/mach-bf537/boards/cm_bf537.c
index 8703b67..f7c1f96 100644
--- a/arch/blackfin/mach-bf537/boards/cm_bf537.c
+++ b/arch/blackfin/mach-bf537/boards/cm_bf537.c
@@ -36,7 +36,7 @@
#include <linux/spi/spi.h>
#include <linux/spi/flash.h>
#include <linux/usb/isp1362.h>
-#include <linux/pata_platform.h>
+#include <linux/ata_platform.h>
#include <linux/irq.h>
#include <asm/dma.h>
#include <asm/bfin5xx_spi.h>
diff --git a/arch/blackfin/mach-bf537/boards/generic_board.c b/arch/blackfin/mach-bf537/boards/generic_board.c
index 3e52f3f..8a3397d 100644
--- a/arch/blackfin/mach-bf537/boards/generic_board.c
+++ b/arch/blackfin/mach-bf537/boards/generic_board.c
@@ -38,7 +38,7 @@
#if defined(CONFIG_USB_ISP1362_HCD) || defined(CONFIG_USB_ISP1362_HCD_MODULE)
#include <linux/usb/isp1362.h>
#endif
-#include <linux/pata_platform.h>
+#include <linux/ata_platform.h>
#include <linux/irq.h>
#include <linux/interrupt.h>
#include <linux/usb/sl811.h>
diff --git a/arch/blackfin/mach-bf537/boards/minotaur.c b/arch/blackfin/mach-bf537/boards/minotaur.c
index b8bbba8..d71e0be 100644
--- a/arch/blackfin/mach-bf537/boards/minotaur.c
+++ b/arch/blackfin/mach-bf537/boards/minotaur.c
@@ -10,7 +10,7 @@
#if defined(CONFIG_USB_ISP1362_HCD) || defined(CONFIG_USB_ISP1362_HCD_MODULE)
#include <linux/usb_isp1362.h>
#endif
-#include <linux/pata_platform.h>
+#include <linux/ata_platform.h>
#include <linux/irq.h>
#include <linux/interrupt.h>
#include <linux/usb_sl811.h>
diff --git a/arch/blackfin/mach-bf537/boards/stamp.c b/arch/blackfin/mach-bf537/boards/stamp.c
index 7725415..119e6ea 100644
--- a/arch/blackfin/mach-bf537/boards/stamp.c
+++ b/arch/blackfin/mach-bf537/boards/stamp.c
@@ -38,7 +38,7 @@
#if defined(CONFIG_USB_ISP1362_HCD) || defined(CONFIG_USB_ISP1362_HCD_MODULE)
#include <linux/usb/isp1362.h>
#endif
-#include <linux/pata_platform.h>
+#include <linux/ata_platform.h>
#include <linux/irq.h>
#include <linux/interrupt.h>
#include <linux/usb/sl811.h>
diff --git a/arch/blackfin/mach-bf561/boards/cm_bf561.c b/arch/blackfin/mach-bf561/boards/cm_bf561.c
index 3a79a90..bf9e738 100644
--- a/arch/blackfin/mach-bf561/boards/cm_bf561.c
+++ b/arch/blackfin/mach-bf561/boards/cm_bf561.c
@@ -34,7 +34,7 @@
#include <linux/spi/spi.h>
#include <linux/spi/flash.h>
#include <linux/usb/isp1362.h>
-#include <linux/pata_platform.h>
+#include <linux/ata_platform.h>
#include <linux/irq.h>
#include <asm/dma.h>
#include <asm/bfin5xx_spi.h>
diff --git a/arch/blackfin/mach-bf561/boards/ezkit.c b/arch/blackfin/mach-bf561/boards/ezkit.c
index 7601c3b..ed863ce 100644
--- a/arch/blackfin/mach-bf561/boards/ezkit.c
+++ b/arch/blackfin/mach-bf561/boards/ezkit.c
@@ -35,7 +35,7 @@
#include <linux/spi/spi.h>
#include <linux/irq.h>
#include <linux/interrupt.h>
-#include <linux/pata_platform.h>
+#include <linux/ata_platform.h>
#include <asm/dma.h>
#include <asm/bfin5xx_spi.h>
#include <asm/portmux.h>
diff --git a/arch/sh/boards/landisk/setup.c b/arch/sh/boards/landisk/setup.c
index eda7176..2b708ec 100644
--- a/arch/sh/boards/landisk/setup.c
+++ b/arch/sh/boards/landisk/setup.c
@@ -14,7 +14,7 @@
*/
#include <linux/init.h>
#include <linux/platform_device.h>
-#include <linux/pata_platform.h>
+#include <linux/ata_platform.h>
#include <linux/pm.h>
#include <linux/mm.h>
#include <asm/machvec.h>
diff --git a/arch/sh/boards/lboxre2/setup.c b/arch/sh/boards/lboxre2/setup.c
index 9c830fd..c74440d 100644
--- a/arch/sh/boards/lboxre2/setup.c
+++ b/arch/sh/boards/lboxre2/setup.c
@@ -13,7 +13,7 @@
#include <linux/init.h>
#include <linux/platform_device.h>
-#include <linux/pata_platform.h>
+#include <linux/ata_platform.h>
#include <asm/machvec.h>
#include <asm/addrspace.h>
#include <asm/lboxre2.h>
diff --git a/arch/sh/boards/renesas/r7780rp/setup.c b/arch/sh/boards/renesas/r7780rp/setup.c
index a43b477..f7a8d5c 100644
--- a/arch/sh/boards/renesas/r7780rp/setup.c
+++ b/arch/sh/boards/renesas/r7780rp/setup.c
@@ -15,7 +15,7 @@
*/
#include <linux/init.h>
#include <linux/platform_device.h>
-#include <linux/pata_platform.h>
+#include <linux/ata_platform.h>
#include <linux/types.h>
#include <net/ax88796.h>
#include <asm/machvec.h>
diff --git a/arch/sh/boards/renesas/rts7751r2d/setup.c b/arch/sh/boards/renesas/rts7751r2d/setup.c
index 3452b07..a0ef81b 100644
--- a/arch/sh/boards/renesas/rts7751r2d/setup.c
+++ b/arch/sh/boards/renesas/rts7751r2d/setup.c
@@ -10,7 +10,7 @@
*/
#include <linux/init.h>
#include <linux/platform_device.h>
-#include <linux/pata_platform.h>
+#include <linux/ata_platform.h>
#include <linux/serial_8250.h>
#include <linux/sm501.h>
#include <linux/sm501-regs.h>
diff --git a/arch/sh/boards/renesas/sdk7780/setup.c b/arch/sh/boards/renesas/sdk7780/setup.c
index 5df32f2..acc5932 100644
--- a/arch/sh/boards/renesas/sdk7780/setup.c
+++ b/arch/sh/boards/renesas/sdk7780/setup.c
@@ -11,7 +11,7 @@
#include <linux/init.h>
#include <linux/types.h>
#include <linux/platform_device.h>
-#include <linux/pata_platform.h>
+#include <linux/ata_platform.h>
#include <asm/machvec.h>
#include <asm/sdk7780.h>
#include <asm/heartbeat.h>
diff --git a/arch/sh/boards/se/7722/setup.c b/arch/sh/boards/se/7722/setup.c
index eb97dca..b1a3d9d 100644
--- a/arch/sh/boards/se/7722/setup.c
+++ b/arch/sh/boards/se/7722/setup.c
@@ -12,7 +12,7 @@
*/
#include <linux/init.h>
#include <linux/platform_device.h>
-#include <linux/pata_platform.h>
+#include <linux/ata_platform.h>
#include <asm/machvec.h>
#include <asm/se7722.h>
#include <asm/io.h>
diff --git a/drivers/ata/ahci.c b/drivers/ata/ahci.c
index 27c8d56..29e71bd 100644
--- a/drivers/ata/ahci.c
+++ b/drivers/ata/ahci.c
@@ -679,24 +679,20 @@ static void ahci_save_initial_config(struct pci_dev *pdev,
/* cross check port_map and cap.n_ports */
if (port_map) {
- u32 tmp_port_map = port_map;
- int n_ports = ahci_nr_ports(cap);
+ int map_ports = 0;
- for (i = 0; i < AHCI_MAX_PORTS && n_ports; i++) {
- if (tmp_port_map & (1 << i)) {
- n_ports--;
- tmp_port_map &= ~(1 << i);
- }
- }
+ for (i = 0; i < AHCI_MAX_PORTS; i++)
+ if (port_map & (1 << i))
+ map_ports++;
- /* If n_ports and port_map are inconsistent, whine and
- * clear port_map and let it be generated from n_ports.
+ /* If PI has more ports than n_ports, whine, clear
+ * port_map and let it be generated from n_ports.
*/
- if (n_ports || tmp_port_map) {
+ if (map_ports > ahci_nr_ports(cap)) {
dev_printk(KERN_WARNING, &pdev->dev,
- "nr_ports (%u) and implemented port map "
- "(0x%x) don't match, using nr_ports\n",
- ahci_nr_ports(cap), port_map);
+ "implemented port map (0x%x) contains more "
+ "ports than nr_ports (%u), using nr_ports\n",
+ port_map, ahci_nr_ports(cap));
port_map = 0;
}
}
@@ -2201,7 +2197,7 @@ static int ahci_init_one(struct pci_dev *pdev, const struct pci_device_id *ent)
struct device *dev = &pdev->dev;
struct ahci_host_priv *hpriv;
struct ata_host *host;
- int i, rc;
+ int n_ports, i, rc;
VPRINTK("ENTER\n");
@@ -2255,7 +2251,14 @@ static int ahci_init_one(struct pci_dev *pdev, const struct pci_device_id *ent)
if (hpriv->cap & HOST_CAP_PMP)
pi.flags |= ATA_FLAG_PMP;
- host = ata_host_alloc_pinfo(&pdev->dev, ppi, fls(hpriv->port_map));
+ /* CAP.NP sometimes indicate the index of the last enabled
+ * port, at other times, that of the last possible port, so
+ * determining the maximum port number requires looking at
+ * both CAP.NP and port_map.
+ */
+ n_ports = max(ahci_nr_ports(hpriv->cap), fls(hpriv->port_map));
+
+ host = ata_host_alloc_pinfo(&pdev->dev, ppi, n_ports);
if (!host)
return -ENOMEM;
host->iomap = pcim_iomap_table(pdev);
diff --git a/drivers/ata/ata_piix.c b/drivers/ata/ata_piix.c
index 4b99ed0..9c2515f 100644
--- a/drivers/ata/ata_piix.c
+++ b/drivers/ata/ata_piix.c
@@ -1603,7 +1603,8 @@ static void piix_iocfg_bit18_quirk(struct pci_dev *pdev)
* Zero on success, or -ERRNO value.
*/
-static int piix_init_one(struct pci_dev *pdev, const struct pci_device_id *ent)
+static int __devinit piix_init_one(struct pci_dev *pdev,
+ const struct pci_device_id *ent)
{
static int printed_version;
struct device *dev = &pdev->dev;
diff --git a/drivers/ata/libata-core.c b/drivers/ata/libata-core.c
index 361cf50..3011919 100644
--- a/drivers/ata/libata-core.c
+++ b/drivers/ata/libata-core.c
@@ -4154,8 +4154,6 @@ static const struct ata_blacklist_entry ata_device_blacklist [] = {
/* NCQ is broken */
{ "Maxtor *", "BANC*", ATA_HORKAGE_NONCQ },
{ "Maxtor 7V300F0", "VA111630", ATA_HORKAGE_NONCQ },
- { "HITACHI HDS7250SASUN500G*", NULL, ATA_HORKAGE_NONCQ },
- { "HITACHI HDS7225SBSUN250G*", NULL, ATA_HORKAGE_NONCQ },
{ "ST380817AS", "3.42", ATA_HORKAGE_NONCQ },
{ "ST3160023AS", "3.42", ATA_HORKAGE_NONCQ },
diff --git a/drivers/ata/pata_of_platform.c b/drivers/ata/pata_of_platform.c
index 938f48a..408da30 100644
--- a/drivers/ata/pata_of_platform.c
+++ b/drivers/ata/pata_of_platform.c
@@ -12,7 +12,7 @@
#include <linux/kernel.h>
#include <linux/module.h>
#include <linux/of_platform.h>
-#include <linux/pata_platform.h>
+#include <linux/ata_platform.h>
static int __devinit pata_of_platform_probe(struct of_device *ofdev,
const struct of_device_id *match)
diff --git a/drivers/ata/pata_platform.c b/drivers/ata/pata_platform.c
index 224bb6c..aad7adc 100644
--- a/drivers/ata/pata_platform.c
+++ b/drivers/ata/pata_platform.c
@@ -19,7 +19,7 @@
#include <linux/ata.h>
#include <linux/libata.h>
#include <linux/platform_device.h>
-#include <linux/pata_platform.h>
+#include <linux/ata_platform.h>
#define DRV_NAME "pata_platform"
#define DRV_VERSION "1.2"
diff --git a/drivers/ata/sata_fsl.c b/drivers/ata/sata_fsl.c
index 922d7b2..efcb66b 100644
--- a/drivers/ata/sata_fsl.c
+++ b/drivers/ata/sata_fsl.c
@@ -355,8 +355,8 @@ static unsigned int sata_fsl_fill_sg(struct ata_queued_cmd *qc, void *cmd_desc,
ata_port_printk(qc->ap, KERN_ERR,
"s/g len unaligned : 0x%x\n", sg_len);
- if ((num_prde == (SATA_FSL_MAX_PRD_DIRECT - 1)) &&
- (qc->n_iter + 1 != qc->n_elem)) {
+ if (num_prde == (SATA_FSL_MAX_PRD_DIRECT - 1) &&
+ sg_next(sg) != NULL) {
VPRINTK("setting indirect prde\n");
prd_ptr_to_indirect_ext = prd;
prd->dba = cpu_to_le32(indirect_ext_segment_paddr);
diff --git a/drivers/ata/sata_mv.c b/drivers/ata/sata_mv.c
index 3c1b5c9..080b836 100644
--- a/drivers/ata/sata_mv.c
+++ b/drivers/ata/sata_mv.c
@@ -69,8 +69,11 @@
#include <linux/blkdev.h>
#include <linux/delay.h>
#include <linux/interrupt.h>
+#include <linux/dmapool.h>
#include <linux/dma-mapping.h>
#include <linux/device.h>
+#include <linux/platform_device.h>
+#include <linux/ata_platform.h>
#include <scsi/scsi_host.h>
#include <scsi/scsi_cmnd.h>
#include <scsi/scsi_device.h>
@@ -179,6 +182,8 @@ enum {
HC_MAIN_IRQ_CAUSE_OFS = 0x1d60,
HC_MAIN_IRQ_MASK_OFS = 0x1d64,
+ HC_SOC_MAIN_IRQ_CAUSE_OFS = 0x20020,
+ HC_SOC_MAIN_IRQ_MASK_OFS = 0x20024,
PORT0_ERR = (1 << 0), /* shift by port # */
PORT0_DONE = (1 << 1), /* shift by port # */
HC0_IRQ_PEND = 0x1ff, /* bits 0-8 = HC0's ports */
@@ -194,11 +199,13 @@ enum {
TWSI_INT = (1 << 24),
HC_MAIN_RSVD = (0x7f << 25), /* bits 31-25 */
HC_MAIN_RSVD_5 = (0x1fff << 19), /* bits 31-19 */
+ HC_MAIN_RSVD_SOC = (0x3fffffb << 6), /* bits 31-9, 7-6 */
HC_MAIN_MASKED_IRQS = (TRAN_LO_DONE | TRAN_HI_DONE |
PORTS_0_7_COAL_DONE | GPIO_INT | TWSI_INT |
HC_MAIN_RSVD),
HC_MAIN_MASKED_IRQS_5 = (PORTS_0_3_COAL_DONE | PORTS_4_7_COAL_DONE |
HC_MAIN_RSVD_5),
+ HC_MAIN_MASKED_IRQS_SOC = (PORTS_0_3_COAL_DONE | HC_MAIN_RSVD_SOC),
/* SATAHC registers */
HC_CFG_OFS = 0,
@@ -368,6 +375,7 @@ enum chip_type {
chip_608x,
chip_6042,
chip_7042,
+ chip_soc,
};
/* Command ReQuest Block: 32B */
@@ -424,6 +432,10 @@ struct mv_host_priv {
u32 hp_flags;
struct mv_port_signal signal[8];
const struct mv_hw_ops *ops;
+ int n_ports;
+ void __iomem *base;
+ void __iomem *main_cause_reg_addr;
+ void __iomem *main_mask_reg_addr;
u32 irq_cause_ofs;
u32 irq_mask_ofs;
u32 unmask_all_irqs;
@@ -482,6 +494,15 @@ static void mv6_read_preamp(struct mv_host_priv *hpriv, int idx,
static int mv6_reset_hc(struct mv_host_priv *hpriv, void __iomem *mmio,
unsigned int n_hc);
static void mv6_reset_flash(struct mv_host_priv *hpriv, void __iomem *mmio);
+static void mv_soc_enable_leds(struct mv_host_priv *hpriv,
+ void __iomem *mmio);
+static void mv_soc_read_preamp(struct mv_host_priv *hpriv, int idx,
+ void __iomem *mmio);
+static int mv_soc_reset_hc(struct mv_host_priv *hpriv,
+ void __iomem *mmio, unsigned int n_hc);
+static void mv_soc_reset_flash(struct mv_host_priv *hpriv,
+ void __iomem *mmio);
+static void mv_soc_reset_bus(struct ata_host *host, void __iomem *mmio);
static void mv_reset_pci_bus(struct ata_host *host, void __iomem *mmio);
static void mv_channel_reset(struct mv_host_priv *hpriv, void __iomem *mmio,
unsigned int port_no);
@@ -661,6 +682,12 @@ static const struct ata_port_info mv_port_info[] = {
.udma_mask = ATA_UDMA6,
.port_ops = &mv_iie_ops,
},
+ { /* chip_soc */
+ .flags = MV_COMMON_FLAGS | MV_FLAG_SOC,
+ .pio_mask = 0x1f, /* pio0-4 */
+ .udma_mask = ATA_UDMA6,
+ .port_ops = &mv_iie_ops,
+ },
};
static const struct pci_device_id mv_pci_tbl[] = {
@@ -711,6 +738,15 @@ static const struct mv_hw_ops mv6xxx_ops = {
.reset_bus = mv_reset_pci_bus,
};
+static const struct mv_hw_ops mv_soc_ops = {
+ .phy_errata = mv6_phy_errata,
+ .enable_leds = mv_soc_enable_leds,
+ .read_preamp = mv_soc_read_preamp,
+ .reset_hc = mv_soc_reset_hc,
+ .reset_flash = mv_soc_reset_flash,
+ .reset_bus = mv_soc_reset_bus,
+};
+
/*
* Functions
*/
@@ -749,9 +785,15 @@ static inline void __iomem *mv_port_base(void __iomem *base, unsigned int port)
(mv_hardport_from_port(port) * MV_PORT_REG_SZ);
}
+static inline void __iomem *mv_host_base(struct ata_host *host)
+{
+ struct mv_host_priv *hpriv = host->private_data;
+ return hpriv->base;
+}
+
static inline void __iomem *mv_ap_base(struct ata_port *ap)
{
- return mv_port_base(ap->host->iomap[MV_PRIMARY_BAR], ap->port_no);
+ return mv_port_base(mv_host_base(ap->host), ap->port_no);
}
static inline int mv_get_hc_count(unsigned long port_flags)
@@ -1649,16 +1691,21 @@ static void mv_intr_edma(struct ata_port *ap)
*/
static void mv_host_intr(struct ata_host *host, u32 relevant, unsigned int hc)
{
- void __iomem *mmio = host->iomap[MV_PRIMARY_BAR];
+ struct mv_host_priv *hpriv = host->private_data;
+ void __iomem *mmio = hpriv->base;
void __iomem *hc_mmio = mv_hc_base(mmio, hc);
u32 hc_irq_cause;
- int port, port0;
+ int port, port0, last_port;
if (hc == 0)
port0 = 0;
else
port0 = MV_PORTS_PER_HC;
+ if (HAS_PCI(host))
+ last_port = port0 + MV_PORTS_PER_HC;
+ else
+ last_port = port0 + hpriv->n_ports;
/* we'll need the HC success int register in most cases */
hc_irq_cause = readl(hc_mmio + HC_IRQ_CAUSE_OFS);
if (!hc_irq_cause)
@@ -1669,7 +1716,7 @@ static void mv_host_intr(struct ata_host *host, u32 relevant, unsigned int hc)
VPRINTK("ENTER, hc%u relevant=0x%08x HC IRQ cause=0x%08x\n",
hc, relevant, hc_irq_cause);
- for (port = port0; port < port0 + MV_PORTS_PER_HC; port++) {
+ for (port = port0; port < port0 + last_port; port++) {
struct ata_port *ap = host->ports[port];
struct mv_port_priv *pp = ap->private_data;
int have_err_bits, hard_port, shift;
@@ -1764,13 +1811,15 @@ static void mv_pci_error(struct ata_host *host, void __iomem *mmio)
static irqreturn_t mv_interrupt(int irq, void *dev_instance)
{
struct ata_host *host = dev_instance;
+ struct mv_host_priv *hpriv = host->private_data;
unsigned int hc, handled = 0, n_hcs;
- void __iomem *mmio = host->iomap[MV_PRIMARY_BAR];
+ void __iomem *mmio = hpriv->base;
u32 irq_stat, irq_mask;
spin_lock(&host->lock);
- irq_stat = readl(mmio + HC_MAIN_IRQ_CAUSE_OFS);
- irq_mask = readl(mmio + HC_MAIN_IRQ_MASK_OFS);
+
+ irq_stat = readl(hpriv->main_cause_reg_addr);
+ irq_mask = readl(hpriv->main_mask_reg_addr);
/* check the cases where we either have nothing pending or have read
* a bogus register value which can indicate HW removal or PCI fault
@@ -1827,7 +1876,8 @@ static unsigned int mv5_scr_offset(unsigned int sc_reg_in)
static int mv5_scr_read(struct ata_port *ap, unsigned int sc_reg_in, u32 *val)
{
- void __iomem *mmio = ap->host->iomap[MV_PRIMARY_BAR];
+ struct mv_host_priv *hpriv = ap->host->private_data;
+ void __iomem *mmio = hpriv->base;
void __iomem *addr = mv5_phy_base(mmio, ap->port_no);
unsigned int ofs = mv5_scr_offset(sc_reg_in);
@@ -1840,7 +1890,8 @@ static int mv5_scr_read(struct ata_port *ap, unsigned int sc_reg_in, u32 *val)
static int mv5_scr_write(struct ata_port *ap, unsigned int sc_reg_in, u32 val)
{
- void __iomem *mmio = ap->host->iomap[MV_PRIMARY_BAR];
+ struct mv_host_priv *hpriv = ap->host->private_data;
+ void __iomem *mmio = hpriv->base;
void __iomem *addr = mv5_phy_base(mmio, ap->port_no);
unsigned int ofs = mv5_scr_offset(sc_reg_in);
@@ -2178,6 +2229,93 @@ static void mv6_phy_errata(struct mv_host_priv *hpriv, void __iomem *mmio,
writel(m2, port_mmio + PHY_MODE2);
}
+/* TODO: use the generic LED interface to configure the SATA Presence */
+/* & Acitivy LEDs on the board */
+static void mv_soc_enable_leds(struct mv_host_priv *hpriv,
+ void __iomem *mmio)
+{
+ return;
+}
+
+static void mv_soc_read_preamp(struct mv_host_priv *hpriv, int idx,
+ void __iomem *mmio)
+{
+ void __iomem *port_mmio;
+ u32 tmp;
+
+ port_mmio = mv_port_base(mmio, idx);
+ tmp = readl(port_mmio + PHY_MODE2);
+
+ hpriv->signal[idx].amps = tmp & 0x700; /* bits 10:8 */
+ hpriv->signal[idx].pre = tmp & 0xe0; /* bits 7:5 */
+}
+
+#undef ZERO
+#define ZERO(reg) writel(0, port_mmio + (reg))
+static void mv_soc_reset_hc_port(struct mv_host_priv *hpriv,
+ void __iomem *mmio, unsigned int port)
+{
+ void __iomem *port_mmio = mv_port_base(mmio, port);
+
+ writelfl(EDMA_DS, port_mmio + EDMA_CMD_OFS);
+
+ mv_channel_reset(hpriv, mmio, port);
+
+ ZERO(0x028); /* command */
+ writel(0x101f, port_mmio + EDMA_CFG_OFS);
+ ZERO(0x004); /* timer */
+ ZERO(0x008); /* irq err cause */
+ ZERO(0x00c); /* irq err mask */
+ ZERO(0x010); /* rq bah */
+ ZERO(0x014); /* rq inp */
+ ZERO(0x018); /* rq outp */
+ ZERO(0x01c); /* respq bah */
+ ZERO(0x024); /* respq outp */
+ ZERO(0x020); /* respq inp */
+ ZERO(0x02c); /* test control */
+ writel(0xbc, port_mmio + EDMA_IORDY_TMOUT);
+}
+
+#undef ZERO
+
+#define ZERO(reg) writel(0, hc_mmio + (reg))
+static void mv_soc_reset_one_hc(struct mv_host_priv *hpriv,
+ void __iomem *mmio)
+{
+ void __iomem *hc_mmio = mv_hc_base(mmio, 0);
+
+ ZERO(0x00c);
+ ZERO(0x010);
+ ZERO(0x014);
+
+}
+
+#undef ZERO
+
+static int mv_soc_reset_hc(struct mv_host_priv *hpriv,
+ void __iomem *mmio, unsigned int n_hc)
+{
+ unsigned int port;
+
+ for (port = 0; port < hpriv->n_ports; port++)
+ mv_soc_reset_hc_port(hpriv, mmio, port);
+
+ mv_soc_reset_one_hc(hpriv, mmio);
+
+ return 0;
+}
+
+static void mv_soc_reset_flash(struct mv_host_priv *hpriv,
+ void __iomem *mmio)
+{
+ return;
+}
+
+static void mv_soc_reset_bus(struct ata_host *host, void __iomem *mmio)
+{
+ return;
+}
+
static void mv_channel_reset(struct mv_host_priv *hpriv, void __iomem *mmio,
unsigned int port_no)
{
@@ -2342,7 +2480,7 @@ static int mv_hardreset(struct ata_link *link, unsigned int *class,
{
struct ata_port *ap = link->ap;
struct mv_host_priv *hpriv = ap->host->private_data;
- void __iomem *mmio = ap->host->iomap[MV_PRIMARY_BAR];
+ void __iomem *mmio = hpriv->base;
mv_stop_dma(ap);
@@ -2383,7 +2521,7 @@ static void mv_error_handler(struct ata_port *ap)
static void mv_eh_freeze(struct ata_port *ap)
{
- void __iomem *mmio = ap->host->iomap[MV_PRIMARY_BAR];
+ struct mv_host_priv *hpriv = ap->host->private_data;
unsigned int hc = (ap->port_no > 3) ? 1 : 0;
u32 tmp, mask;
unsigned int shift;
@@ -2397,13 +2535,14 @@ static void mv_eh_freeze(struct ata_port *ap)
mask = 0x3 << shift;
/* disable assertion of portN err, done events */
- tmp = readl(mmio + HC_MAIN_IRQ_MASK_OFS);
- writelfl(tmp & ~mask, mmio + HC_MAIN_IRQ_MASK_OFS);
+ tmp = readl(hpriv->main_mask_reg_addr);
+ writelfl(tmp & ~mask, hpriv->main_mask_reg_addr);
}
static void mv_eh_thaw(struct ata_port *ap)
{
- void __iomem *mmio = ap->host->iomap[MV_PRIMARY_BAR];
+ struct mv_host_priv *hpriv = ap->host->private_data;
+ void __iomem *mmio = hpriv->base;
unsigned int hc = (ap->port_no > 3) ? 1 : 0;
void __iomem *hc_mmio = mv_hc_base(mmio, hc);
void __iomem *port_mmio = mv_ap_base(ap);
@@ -2430,8 +2569,8 @@ static void mv_eh_thaw(struct ata_port *ap)
writel(hc_irq_cause, hc_mmio + HC_IRQ_CAUSE_OFS);
/* enable assertion of portN err, done events */
- tmp = readl(mmio + HC_MAIN_IRQ_MASK_OFS);
- writelfl(tmp | mask, mmio + HC_MAIN_IRQ_MASK_OFS);
+ tmp = readl(hpriv->main_mask_reg_addr);
+ writelfl(tmp | mask, hpriv->main_mask_reg_addr);
}
/**
@@ -2598,9 +2737,13 @@ static int mv_chip_id(struct ata_host *host, unsigned int board_idx)
break;
}
break;
+ case chip_soc:
+ hpriv->ops = &mv_soc_ops;
+ hp_flags |= MV_HP_ERRATA_60X1C0;
+ break;
default:
- dev_printk(KERN_ERR, &pdev->dev,
+ dev_printk(KERN_ERR, host->dev,
"BUG: invalid board index %u\n", board_idx);
return 1;
}
@@ -2633,15 +2776,25 @@ static int mv_chip_id(struct ata_host *host, unsigned int board_idx)
static int mv_init_host(struct ata_host *host, unsigned int board_idx)
{
int rc = 0, n_hc, port, hc;
- void __iomem *mmio = host->iomap[MV_PRIMARY_BAR];
struct mv_host_priv *hpriv = host->private_data;
-
- /* global interrupt mask */
- writel(0, mmio + HC_MAIN_IRQ_MASK_OFS);
+ void __iomem *mmio = hpriv->base;
rc = mv_chip_id(host, board_idx);
if (rc)
- goto done;
+ goto done;
+
+ if (HAS_PCI(host)) {
+ hpriv->main_cause_reg_addr = hpriv->base +
+ HC_MAIN_IRQ_CAUSE_OFS;
+ hpriv->main_mask_reg_addr = hpriv->base + HC_MAIN_IRQ_MASK_OFS;
+ } else {
+ hpriv->main_cause_reg_addr = hpriv->base +
+ HC_SOC_MAIN_IRQ_CAUSE_OFS;
+ hpriv->main_mask_reg_addr = hpriv->base +
+ HC_SOC_MAIN_IRQ_MASK_OFS;
+ }
+ /* global interrupt mask */
+ writel(0, hpriv->main_mask_reg_addr);
n_hc = mv_get_hc_count(host->ports[0]->flags);
@@ -2672,13 +2825,15 @@ static int mv_init_host(struct ata_host *host, unsigned int board_idx)
for (port = 0; port < host->n_ports; port++) {
struct ata_port *ap = host->ports[port];
void __iomem *port_mmio = mv_port_base(mmio, port);
- unsigned int offset = port_mmio - mmio;
mv_port_init(&ap->ioaddr, port_mmio);
#ifdef CONFIG_PCI
- ata_port_pbar_desc(ap, MV_PRIMARY_BAR, -1, "mmio");
- ata_port_pbar_desc(ap, MV_PRIMARY_BAR, offset, "port");
+ if (HAS_PCI(host)) {
+ unsigned int offset = port_mmio - mmio;
+ ata_port_pbar_desc(ap, MV_PRIMARY_BAR, -1, "mmio");
+ ata_port_pbar_desc(ap, MV_PRIMARY_BAR, offset, "port");
+ }
#endif
}
@@ -2694,35 +2849,141 @@ static int mv_init_host(struct ata_host *host, unsigned int board_idx)
writelfl(0, hc_mmio + HC_IRQ_CAUSE_OFS);
}
- /* Clear any currently outstanding host interrupt conditions */
- writelfl(0, mmio + hpriv->irq_cause_ofs);
+ if (HAS_PCI(host)) {
+ /* Clear any currently outstanding host interrupt conditions */
+ writelfl(0, mmio + hpriv->irq_cause_ofs);
- /* and unmask interrupt generation for host regs */
- writelfl(hpriv->unmask_all_irqs, mmio + hpriv->irq_mask_ofs);
+ /* and unmask interrupt generation for host regs */
+ writelfl(hpriv->unmask_all_irqs, mmio + hpriv->irq_mask_ofs);
+ if (IS_GEN_I(hpriv))
+ writelfl(~HC_MAIN_MASKED_IRQS_5,
+ hpriv->main_mask_reg_addr);
+ else
+ writelfl(~HC_MAIN_MASKED_IRQS,
+ hpriv->main_mask_reg_addr);
+
+ VPRINTK("HC MAIN IRQ cause/mask=0x%08x/0x%08x "
+ "PCI int cause/mask=0x%08x/0x%08x\n",
+ readl(hpriv->main_cause_reg_addr),
+ readl(hpriv->main_mask_reg_addr),
+ readl(mmio + hpriv->irq_cause_ofs),
+ readl(mmio + hpriv->irq_mask_ofs));
+ } else {
+ writelfl(~HC_MAIN_MASKED_IRQS_SOC,
+ hpriv->main_mask_reg_addr);
+ VPRINTK("HC MAIN IRQ cause/mask=0x%08x/0x%08x\n",
+ readl(hpriv->main_cause_reg_addr),
+ readl(hpriv->main_mask_reg_addr));
+ }
+done:
+ return rc;
+}
- if (IS_GEN_I(hpriv))
- writelfl(~HC_MAIN_MASKED_IRQS_5, mmio + HC_MAIN_IRQ_MASK_OFS);
- else
- writelfl(~HC_MAIN_MASKED_IRQS, mmio + HC_MAIN_IRQ_MASK_OFS);
+/**
+ * mv_platform_probe - handle a positive probe of an soc Marvell
+ * host
+ * @pdev: platform device found
+ *
+ * LOCKING:
+ * Inherited from caller.
+ */
+static int mv_platform_probe(struct platform_device *pdev)
+{
+ static int printed_version;
+ const struct mv_sata_platform_data *mv_platform_data;
+ const struct ata_port_info *ppi[] =
+ { &mv_port_info[chip_soc], NULL };
+ struct ata_host *host;
+ struct mv_host_priv *hpriv;
+ struct resource *res;
+ int n_ports, rc;
- VPRINTK("HC MAIN IRQ cause/mask=0x%08x/0x%08x "
- "PCI int cause/mask=0x%08x/0x%08x\n",
- readl(mmio + HC_MAIN_IRQ_CAUSE_OFS),
- readl(mmio + HC_MAIN_IRQ_MASK_OFS),
- readl(mmio + hpriv->irq_cause_ofs),
- readl(mmio + hpriv->irq_mask_ofs));
+ if (!printed_version++)
+ dev_printk(KERN_INFO, &pdev->dev, "version " DRV_VERSION "\n");
-done:
- return rc;
+ /*
+ * Simple resource validation ..
+ */
+ if (unlikely(pdev->num_resources != 2)) {
+ dev_err(&pdev->dev, "invalid number of resources\n");
+ return -EINVAL;
+ }
+
+ /*
+ * Get the register base first
+ */
+ res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ if (res == NULL)
+ return -EINVAL;
+
+ /* allocate host */
+ mv_platform_data = pdev->dev.platform_data;
+ n_ports = mv_platform_data->n_ports;
+
+ host = ata_host_alloc_pinfo(&pdev->dev, ppi, n_ports);
+ hpriv = devm_kzalloc(&pdev->dev, sizeof(*hpriv), GFP_KERNEL);
+
+ if (!host || !hpriv)
+ return -ENOMEM;
+ host->private_data = hpriv;
+ hpriv->n_ports = n_ports;
+
+ host->iomap = NULL;
+ hpriv->base = ioremap(res->start, res->end - res->start + 1);
+ hpriv->base -= MV_SATAHC0_REG_BASE;
+
+ /* initialize adapter */
+ rc = mv_init_host(host, chip_soc);
+ if (rc)
+ return rc;
+
+ dev_printk(KERN_INFO, &pdev->dev,
+ "slots %u ports %d\n", (unsigned)MV_MAX_Q_DEPTH,
+ host->n_ports);
+
+ return ata_host_activate(host, platform_get_irq(pdev, 0), mv_interrupt,
+ IRQF_SHARED, &mv6_sht);
+}
+
+/*
+ *
+ * mv_platform_remove - unplug a platform interface
+ * @pdev: platform device
+ *
+ * A platform bus SATA device has been unplugged. Perform the needed
+ * cleanup. Also called on module unload for any active devices.
+ */
+static int __devexit mv_platform_remove(struct platform_device *pdev)
+{
+ struct device *dev = &pdev->dev;
+ struct ata_host *host = dev_get_drvdata(dev);
+ struct mv_host_priv *hpriv = host->private_data;
+ void __iomem *base = hpriv->base;
+
+ ata_host_detach(host);
+ iounmap(base);
+ return 0;
}
+static struct platform_driver mv_platform_driver = {
+ .probe = mv_platform_probe,
+ .remove = __devexit_p(mv_platform_remove),
+ .driver = {
+ .name = DRV_NAME,
+ .owner = THIS_MODULE,
+ },
+};
+
+
#ifdef CONFIG_PCI
-static int mv_init_one(struct pci_dev *pdev, const struct pci_device_id *ent);
+static int mv_pci_init_one(struct pci_dev *pdev,
+ const struct pci_device_id *ent);
+
static struct pci_driver mv_pci_driver = {
.name = DRV_NAME,
.id_table = mv_pci_tbl,
- .probe = mv_init_one,
+ .probe = mv_pci_init_one,
.remove = ata_pci_remove_one,
};
@@ -2828,14 +3089,15 @@ static int mv_create_dma_pools(struct mv_host_priv *hpriv, struct device *dev)
}
/**
- * mv_init_one - handle a positive probe of a Marvell host
+ * mv_pci_init_one - handle a positive probe of a PCI Marvell host
* @pdev: PCI device found
* @ent: PCI device ID entry for the matched host
*
* LOCKING:
* Inherited from caller.
*/
-static int mv_init_one(struct pci_dev *pdev, const struct pci_device_id *ent)
+static int mv_pci_init_one(struct pci_dev *pdev,
+ const struct pci_device_id *ent)
{
static int printed_version;
unsigned int board_idx = (unsigned int)ent->driver_data;
@@ -2855,6 +3117,7 @@ static int mv_init_one(struct pci_dev *pdev, const struct pci_device_id *ent)
if (!host || !hpriv)
return -ENOMEM;
host->private_data = hpriv;
+ hpriv->n_ports = n_ports;
/* acquire resources */
rc = pcim_enable_device(pdev);
@@ -2867,6 +3130,7 @@ static int mv_init_one(struct pci_dev *pdev, const struct pci_device_id *ent)
if (rc)
return rc;
host->iomap = pcim_iomap_table(pdev);
+ hpriv->base = host->iomap[MV_PRIMARY_BAR];
rc = pci_go_64(pdev);
if (rc)
@@ -2895,11 +3159,22 @@ static int mv_init_one(struct pci_dev *pdev, const struct pci_device_id *ent)
}
#endif
+static int mv_platform_probe(struct platform_device *pdev);
+static int __devexit mv_platform_remove(struct platform_device *pdev);
+
static int __init mv_init(void)
{
int rc = -ENODEV;
#ifdef CONFIG_PCI
rc = pci_register_driver(&mv_pci_driver);
+ if (rc < 0)
+ return rc;
+#endif
+ rc = platform_driver_register(&mv_platform_driver);
+
+#ifdef CONFIG_PCI
+ if (rc < 0)
+ pci_unregister_driver(&mv_pci_driver);
#endif
return rc;
}
@@ -2909,6 +3184,7 @@ static void __exit mv_exit(void)
#ifdef CONFIG_PCI
pci_unregister_driver(&mv_pci_driver);
#endif
+ platform_driver_unregister(&mv_platform_driver);
}
MODULE_AUTHOR("Brett Russ");
diff --git a/drivers/ata/sata_nv.c b/drivers/ata/sata_nv.c
index bfe92a4..ed5473b 100644
--- a/drivers/ata/sata_nv.c
+++ b/drivers/ata/sata_nv.c
@@ -247,6 +247,7 @@ struct nv_adma_port_priv {
void __iomem *ctl_block;
void __iomem *gen_block;
void __iomem *notifier_clear_block;
+ u64 adma_dma_mask;
u8 flags;
int last_issue_ncq;
};
@@ -715,9 +716,10 @@ static int nv_adma_slave_config(struct scsi_device *sdev)
{
struct ata_port *ap = ata_shost_to_port(sdev->host);
struct nv_adma_port_priv *pp = ap->private_data;
+ struct nv_adma_port_priv *port0, *port1;
+ struct scsi_device *sdev0, *sdev1;
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
- u64 bounce_limit;
- unsigned long segment_boundary;
+ unsigned long segment_boundary, flags;
unsigned short sg_tablesize;
int rc;
int adma_enable;
@@ -729,6 +731,8 @@ static int nv_adma_slave_config(struct scsi_device *sdev)
/* Not a proper libata device, ignore */
return rc;
+ spin_lock_irqsave(ap->lock, flags);
+
if (ap->link.device[sdev->id].class == ATA_DEV_ATAPI) {
/*
* NVIDIA reports that ADMA mode does not support ATAPI commands.
@@ -737,7 +741,6 @@ static int nv_adma_slave_config(struct scsi_device *sdev)
* Restrict DMA parameters as required by the legacy interface
* when an ATAPI device is connected.
*/
- bounce_limit = ATA_DMA_MASK;
segment_boundary = ATA_DMA_BOUNDARY;
/* Subtract 1 since an extra entry may be needed for padding, see
libata-scsi.c */
@@ -748,7 +751,6 @@ static int nv_adma_slave_config(struct scsi_device *sdev)
adma_enable = 0;
nv_adma_register_mode(ap);
} else {
- bounce_limit = *ap->dev->dma_mask;
segment_boundary = NV_ADMA_DMA_BOUNDARY;
sg_tablesize = NV_ADMA_SGTBL_TOTAL_LEN;
adma_enable = 1;
@@ -774,12 +776,49 @@ static int nv_adma_slave_config(struct scsi_device *sdev)
if (current_reg != new_reg)
pci_write_config_dword(pdev, NV_MCP_SATA_CFG_20, new_reg);
- blk_queue_bounce_limit(sdev->request_queue, bounce_limit);
+ port0 = ap->host->ports[0]->private_data;
+ port1 = ap->host->ports[1]->private_data;
+ sdev0 = ap->host->ports[0]->link.device[0].sdev;
+ sdev1 = ap->host->ports[1]->link.device[0].sdev;
+ if ((port0->flags & NV_ADMA_ATAPI_SETUP_COMPLETE) ||
+ (port1->flags & NV_ADMA_ATAPI_SETUP_COMPLETE)) {
+ /** We have to set the DMA mask to 32-bit if either port is in
+ ATAPI mode, since they are on the same PCI device which is
+ used for DMA mapping. If we set the mask we also need to set
+ the bounce limit on both ports to ensure that the block
+ layer doesn't feed addresses that cause DMA mapping to
+ choke. If either SCSI device is not allocated yet, it's OK
+ since that port will discover its correct setting when it
+ does get allocated.
+ Note: Setting 32-bit mask should not fail. */
+ if (sdev0)
+ blk_queue_bounce_limit(sdev0->request_queue,
+ ATA_DMA_MASK);
+ if (sdev1)
+ blk_queue_bounce_limit(sdev1->request_queue,
+ ATA_DMA_MASK);
+
+ pci_set_dma_mask(pdev, ATA_DMA_MASK);
+ } else {
+ /** This shouldn't fail as it was set to this value before */
+ pci_set_dma_mask(pdev, pp->adma_dma_mask);
+ if (sdev0)
+ blk_queue_bounce_limit(sdev0->request_queue,
+ pp->adma_dma_mask);
+ if (sdev1)
+ blk_queue_bounce_limit(sdev1->request_queue,
+ pp->adma_dma_mask);
+ }
+
blk_queue_segment_boundary(sdev->request_queue, segment_boundary);
blk_queue_max_hw_segments(sdev->request_queue, sg_tablesize);
ata_port_printk(ap, KERN_INFO,
- "bounce limit 0x%llX, segment boundary 0x%lX, hw segs %hu\n",
- (unsigned long long)bounce_limit, segment_boundary, sg_tablesize);
+ "DMA mask 0x%llX, segment boundary 0x%lX, hw segs %hu\n",
+ (unsigned long long)*ap->host->dev->dma_mask,
+ segment_boundary, sg_tablesize);
+
+ spin_unlock_irqrestore(ap->lock, flags);
+
return rc;
}
@@ -1140,10 +1179,20 @@ static int nv_adma_port_start(struct ata_port *ap)
void *mem;
dma_addr_t mem_dma;
void __iomem *mmio;
+ struct pci_dev *pdev = to_pci_dev(dev);
u16 tmp;
VPRINTK("ENTER\n");
+ /* Ensure DMA mask is set to 32-bit before allocating legacy PRD and
+ pad buffers */
+ rc = pci_set_dma_mask(pdev, DMA_BIT_MASK(32));
+ if (rc)
+ return rc;
+ rc = pci_set_consistent_dma_mask(pdev, DMA_BIT_MASK(32));
+ if (rc)
+ return rc;
+
rc = ata_port_start(ap);
if (rc)
return rc;
@@ -1159,6 +1208,15 @@ static int nv_adma_port_start(struct ata_port *ap)
pp->notifier_clear_block = pp->gen_block +
NV_ADMA_NOTIFIER_CLEAR + (4 * ap->port_no);
+ /* Now that the legacy PRD and padding buffer are allocated we can
+ safely raise the DMA mask to allocate the CPB/APRD table.
+ These are allowed to fail since we store the value that ends up
+ being used to set as the bounce limit in slave_config later if
+ needed. */
+ pci_set_dma_mask(pdev, DMA_BIT_MASK(64));
+ pci_set_consistent_dma_mask(pdev, DMA_BIT_MASK(64));
+ pp->adma_dma_mask = *dev->dma_mask;
+
mem = dmam_alloc_coherent(dev, NV_ADMA_PORT_PRIV_DMA_SZ,
&mem_dma, GFP_KERNEL);
if (!mem)
@@ -2417,12 +2475,6 @@ static int nv_init_one(struct pci_dev *pdev, const struct pci_device_id *ent)
hpriv->type = type;
host->private_data = hpriv;
- /* set 64bit dma masks, may fail */
- if (type == ADMA) {
- if (pci_set_dma_mask(pdev, DMA_64BIT_MASK) == 0)
- pci_set_consistent_dma_mask(pdev, DMA_64BIT_MASK);
- }
-
/* request and iomap NV_MMIO_BAR */
rc = pcim_iomap_regions(pdev, 1 << NV_MMIO_BAR, DRV_NAME);
if (rc)
diff --git a/drivers/ata/sata_via.c b/drivers/ata/sata_via.c
index 3ef072f..30caa03 100644
--- a/drivers/ata/sata_via.c
+++ b/drivers/ata/sata_via.c
@@ -30,8 +30,6 @@
* Hardware documentation available under NDA.
*
*
- * To-do list:
- * - VT6421 PATA support
*
*/
diff --git a/drivers/ide/legacy/ide_platform.c b/drivers/ide/legacy/ide_platform.c
index 26c82ce..688fcae 100644
--- a/drivers/ide/legacy/ide_platform.c
+++ b/drivers/ide/legacy/ide_platform.c
@@ -17,7 +17,7 @@
#include <linux/ide.h>
#include <linux/ioport.h>
#include <linux/module.h>
-#include <linux/pata_platform.h>
+#include <linux/ata_platform.h>
#include <linux/platform_device.h>
#include <linux/io.h>
diff --git a/include/linux/ata_platform.h b/include/linux/ata_platform.h
new file mode 100644
index 0000000..b856a2a
--- /dev/null
+++ b/include/linux/ata_platform.h
@@ -0,0 +1,34 @@
+#ifndef __LINUX_ATA_PLATFORM_H
+#define __LINUX_ATA_PLATFORM_H
+
+struct pata_platform_info {
+ /*
+ * I/O port shift, for platforms with ports that are
+ * constantly spaced and need larger than the 1-byte
+ * spacing used by ata_std_ports().
+ */
+ unsigned int ioport_shift;
+ /*
+ * Indicate platform specific irq types and initial
+ * IRQ flags when call request_irq()
+ */
+ unsigned int irq_flags;
+};
+
+extern int __devinit __pata_platform_probe(struct device *dev,
+ struct resource *io_res,
+ struct resource *ctl_res,
+ struct resource *irq_res,
+ unsigned int ioport_shift,
+ int __pio_mask);
+
+extern int __devexit __pata_platform_remove(struct device *dev);
+
+/*
+ * Marvell SATA private data
+ */
+struct mv_sata_platform_data {
+ int n_ports; /* number of sata ports */
+};
+
+#endif /* __LINUX_ATA_PLATFORM_H */
diff --git a/include/linux/libata.h b/include/linux/libata.h
index 4374c42..bc5a8d0 100644
--- a/include/linux/libata.h
+++ b/include/linux/libata.h
@@ -457,7 +457,6 @@ struct ata_queued_cmd {
unsigned long flags; /* ATA_QCFLAG_xxx */
unsigned int tag;
unsigned int n_elem;
- unsigned int n_iter;
unsigned int mapped_n_elem;
int dma_dir;
@@ -1367,7 +1366,6 @@ static inline void ata_qc_reinit(struct ata_queued_cmd *qc)
qc->nbytes = qc->raw_nbytes = qc->curbytes = 0;
qc->n_elem = 0;
qc->mapped_n_elem = 0;
- qc->n_iter = 0;
qc->err_mask = 0;
qc->pad_len = 0;
qc->last_sg = NULL;
diff --git a/include/linux/pata_platform.h b/include/linux/pata_platform.h
deleted file mode 100644
index 6a7a92d..0000000
--- a/include/linux/pata_platform.h
+++ /dev/null
@@ -1,27 +0,0 @@
-#ifndef __LINUX_PATA_PLATFORM_H
-#define __LINUX_PATA_PLATFORM_H
-
-struct pata_platform_info {
- /*
- * I/O port shift, for platforms with ports that are
- * constantly spaced and need larger than the 1-byte
- * spacing used by ata_std_ports().
- */
- unsigned int ioport_shift;
- /*
- * Indicate platform specific irq types and initial
- * IRQ flags when call request_irq()
- */
- unsigned int irq_flags;
-};
-
-extern int __devinit __pata_platform_probe(struct device *dev,
- struct resource *io_res,
- struct resource *ctl_res,
- struct resource *irq_res,
- unsigned int ioport_shift,
- int __pio_mask);
-
-extern int __devexit __pata_platform_remove(struct device *dev);
-
-#endif /* __LINUX_PATA_PLATFORM_H */
-
To unsubscribe from this list: send the line "unsubscribe linux-ide" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
