Jeff Garzik írta:
Zoltan Boszormenyi wrote:
Hi,
Jeff Garzik írta:
akpm@xxxxxxxxxxxxxxxxxxxx wrote:
From: Kuan Luo <kluo@xxxxxxxxxx>
Add the Software NCQ support to sata_nv.c for MCP51/MCP55/MCP61 SATA
controller. NCQ function is disable by default, you can enable it
with
'swncq=1'. NCQ will be turned off if the drive is Maxtor on MCP51
or MCP55
rev 0xa2 platform.
[akpm@xxxxxxxxxxxxxxxxxxxx: build fix]
Signed-off-by: Kuan Luo <kluo@xxxxxxxxxx>
Signed-off-by: Peer Chen <pchen@xxxxxxxxxx>
Cc: Zoltan Boszormenyi <zboszor@xxxxxxxxxx>
Signed-off-by: Andrew Morton <akpm@xxxxxxxxxxxxxxxxxxxx>
---
drivers/ata/sata_nv.c | 860 +++++++++++++++++++++++++++++++++++++++-
1 files changed, 851 insertions(+), 9 deletions(-)
I finally gave this a thorough review.
Overall, good work. The state transitions all seem solid. I made
several minor changes and cleanups, and checked it into the
'nv-swncq' branch of
git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev.git
Two hurdles before I'm ready to push upstream:
* someone please verify my minor changes did not break anything; I
don't have real hardware
After reading the diff between the original and your cleaned up version
it seems both the change from 4 individual flags to a single integer
and the
nv_swncq_bmdma_stop() -> __ata_bmdma_stop() transition are obviously
correct.
I attached a small cleanup patch which may make one check a bit more
readable.
However, can you explain this chunk below? Why isn't it needed?
@@ -615,7 +622,6 @@ static const struct ata_port_info nv_por
{
.sht = &nv_swncq_sht,
.flags = ATA_FLAG_SATA | ATA_FLAG_NO_LEGACY,
- .link_flags = ATA_LFLAG_HRST_TO_RESUME,
.pio_mask = NV_PIO_MASK,
.mwdma_mask = NV_MWDMA_MASK,
.udma_mask = NV_UDMA_MASK,
that's a bug. fixed.
I also applied your cleanup.
Thanks, but you took the wrong cleanup patch.
My original, i.e. this chunk below is wrong.
@@ -2291,8
<http://git.kernel.org/?p=linux/kernel/git/jgarzik/libata-dev.git;a=blob;f=drivers/ata/sata_nv.c;h=540f218e10e56c8a85a937bc920a5d96434bcc8f;hb=41f0f8af3edfccd58b5c9d714928d773a072b693#l2291>
+2283,7
<http://git.kernel.org/?p=linux/kernel/git/jgarzik/libata-dev.git;a=blob;f=drivers/ata/sata_nv.c;h=ffd00f5c533d7b58dde67cfef7d2191ca15ea140;hb=5a5a9e1890b8260686218a68862d880daee1a817#l2283>
@@ static void nv_swncq_host_interrupt(struct ata_port *ap, u16 fis)
*/
pp->dhfis_bits |= (0x1 << pp->last_issue_tag);
pp->ncq_flags |= ncq_saw_d2h;
- if ((pp->ncq_flags & ncq_saw_sdb) ||
- (pp->ncq_flags & ncq_saw_backout)) {
+ if (pp->ncq_flags & (ncq_saw_sdb || ncq_saw_backout)) {
ata_ehi_push_desc(ehi, "illegal fis transaction");
ehi->err_mask |= AC_ERR_HSM;
ehi->action |= ATA_EH_HARDRESET;
It should be a binary OR between the flags. This caused immediate
NCQ errors upon boot and lead to disabling NCQ.
My second patch has it corrected.
Best regards,
Zoltán Böszörményi
-
To unsubscribe from this list: send the line "unsubscribe linux-ide" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html