Re: [PATCH 2/4] hpt366: UltraDMA filter for SATA cards (take 3)

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Bartlomiej Zolnierkiewicz wrote:

The Marvell bridge chips used on HighPoint SATA cards do not seem to support
the UltraDMA modes 1, 2, and 3 as well as any MWDMA modes, so the driver needs
to account for this in the udma_filter() method.  In order to achieve that, do
the following changes:

- install the method for all chips, not only HPT36x/370 and impove the code
 formatting by killing the extra tabs while at it;

- add to the end of the 'switch' statement in the method cases for HPT372[AN]
 and HPT374 chips upon which the known SATA cards are based;

- use hwif->ultra_mask as a default mask for the ide_dma_filter() method to
 behave correctly;

- move the HPT370[A] cases below the HPT36x case for consistency...

Signed-off-by: Sergei Shtylyov <sshtylyov@xxxxxxxxxxxxx>

---
Argh!  I've managed to put = instead of &= here and there, so please disregard
the take #2... :-/

Not to mention that there was already take #2 on Aug 19 2007
(the version of the patch which is currently in IDE quilt tree)...

I've just changed my mind about which series it'd beliong too -- propply need to post [0/n] message before the series....

This version doesn't use explicit UltraDMA masks, so converting them to the
ATA_UDMA* is left for another, global patch.  This patch against the current

I have already other patches which are based on the previous version of the
patch and I don't find the idea of re-doing them especially tempting...

   Too bad. :-)
I don't find the idea if the open coded masks depnding on HPT3*_ALLOW_ATA* for a catch all udma_filter() method especially tempting to. :-)

Linus' tree and unfortunately I was able to only compile test it since that
tree gives MODPOST warning and dies early on bootup.

Index: linux-2.6/drivers/ide/pci/hpt366.c
===================================================================
--- linux-2.6.orig/drivers/ide/pci/hpt366.c
+++ linux-2.6/drivers/ide/pci/hpt366.c
@@ -1,5 +1,5 @@
/*
- * linux/drivers/ide/pci/hpt366.c		Version 1.11	Aug 11, 2007
+ * linux/drivers/ide/pci/hpt366.c		Version 1.12	Aug 25, 2007
 *
 * Copyright (C) 1999-2003		Andre Hedrick <andre@xxxxxxxxxxxxx>
 * Portions Copyright (C) 2001	        Sun Microsystems, Inc.
@@ -114,6 +114,7 @@
 *   unify HPT36x/37x timing setup code and the speedproc handlers by joining
 *   the register setting lists into the table indexed by the clock selected
 * - set the correct hwif->ultra_mask for each individual chip
+ * - add UltraDMA mode filtering for the HPT37[24] based SATA cards
 *	Sergei Shtylyov, <sshtylyov@xxxxxxxxxxxxx> or <source@xxxxxxxxxx>
 */

@@ -524,36 +525,38 @@ static int check_in_drive_list(ide_drive

(the real) take #2 also updated hpt3xx_udma_filter() comment

I've probably dropped that part in anticipation of adding mdma_filter... I agree -- future has always come. B-)

static u8 hpt3xx_udma_filter(ide_drive_t *drive)
{
-	struct hpt_info *info	= pci_get_drvdata(HWIF(drive)->pci_dev);
-	u8 mask;
+	ide_hwif_t *hwif	= HWIF(drive);
+	struct hpt_info *info	= pci_get_drvdata(hwif->pci_dev);
+	u8 mask 		= hwif->ultra_mask;

	switch (info->chip_type) {
-	case HPT370A:
-		if (!HPT370_ALLOW_ATA100_5 ||
-		    check_in_drive_list(drive, bad_ata100_5))
-			return 0x1f;
-		else
-			return 0x3f;
-	case HPT370:
-		if (!HPT370_ALLOW_ATA100_5 ||
-		    check_in_drive_list(drive, bad_ata100_5))
-			mask = 0x1f;
-		else
-			mask = 0x3f;
-		break;
	case HPT36x:
-		if (!HPT366_ALLOW_ATA66_4 ||
+		if (HPT366_ALLOW_ATA66_4 &&
		    check_in_drive_list(drive, bad_ata66_4))
-			mask = 0x0f;
-		else
-			mask = 0x1f;
+			mask &= ~0x10;

-		if (!HPT366_ALLOW_ATA66_3 ||
+		if (HPT366_ALLOW_ATA66_3 &&
		    check_in_drive_list(drive, bad_ata66_3))
-			mask = 0x07;
+			mask &= ~0x08;
		break;
+	case HPT370 :
+	case HPT370A:
+		if (HPT370_ALLOW_ATA100_5 &&
+		    check_in_drive_list(drive, bad_ata100_5))
+			mask &= ~0x20;
+
+		if (info->chip_type == HPT370A)
+			return mask;
+		break;
+	case HPT372 :
+	case HPT372A:
+	case HPT372N:
+	case HPT374 :
+		if (ide_dev_is_sata(drive->id))
+			mask &= ~0x0e;
+		/* Fall thru */
	default:
-		return 0x7f;
+		return mask;
	}

I really don't see the advantage of "mask &=" over the previous

   Considered the smaller code? ;-)

code ("mask = ATA_UDMA*") which was just more readable IMO.

Like I said, I don't want to be tied by HPT3*_ALLOW_ATA* here and there (BTW, this approach was in revision #0 which I've never published :-).

I'm staying with (the real) take #2 of this patch for now.

   I'll respin RSN... but not take #2, alas. B-)

Bart

MBR, Sergei
-
To unsubscribe from this list: send the line "unsubscribe linux-ide" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html

[Index of Archives]     [Linux Filesystems]     [Linux SCSI]     [Linux RAID]     [Git]     [Kernel Newbies]     [Linux Newbie]     [Security]     [Netfilter]     [Bugtraq]     [Yosemite News]     [MIPS Linux]     [ARM Linux]     [Linux Security]     [Samba]     [Device Mapper]

  Powered by Linux