* All other implementations of ->speedproc return zero on success
and non-zero on failure. Currently it doesn't matter for icside host
driver and isn't a bug per se since:
- ide_set_xfer_rate() return value is ignored by all IDE core users
- icside doesn't (yet!) use ide_tune_dma() in icside_dma_check()
but sooner or later we will need to fix anyway - so lets do it now.
* icside_set_speed() happily accepts unsupported transfer modes which
results in drive->drive_data being set to the maximum value (480)
and drive->current_speed being set to the unsupported transfer mode.
Fix it.
v2:
* The initial version of the patch was broken because it didn't take into
the account (the different from usual) return values of icside_set_speed()
(Noticed by Russell).
v3:
* Remove no longer needed initialization/checking of cycle_time
(Noticed by Sergei).
* No need to set drive->drive_data if DMA is not going to be used
(Noticed by Sergei).
* Remove incorrect setting of drive->current_speed
(Noticed by Sergei).
* Move ide_config_drive_speed() at the end of icside_set_speed().
v4:
* If DMA mode is not found in icside_dma_check() then just return "-1" and
don't call icside_set_speed() (v3 got it wrong and "1" was returned instead).
v5:
* Return "-1"/"0" in icside_set_speed() instead of icside_dma_check() return
value (just like it was before this patch).
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@xxxxxxxxx>
Cc: Russell King <rmk@xxxxxxxxxxxxxxxx>
Cc: Sergei Shtylyov <sshtylyov@xxxxxxxxxxxxx>
---
replacement patch for the one in IDE quilt tree
drivers/ide/arm/icside.c | 21 ++++++++-------------
1 file changed, 8 insertions(+), 13 deletions(-)
Index: b/drivers/ide/arm/icside.c
===================================================================
--- a/drivers/ide/arm/icside.c
+++ b/drivers/ide/arm/icside.c
@@ -250,7 +250,7 @@ static void icside_build_sglist(ide_driv
*/
static int icside_set_speed(ide_drive_t *drive, const u8 xfer_mode)
{
- int on = 0, cycle_time = 0, use_dma_info = 0;
+ int cycle_time, use_dma_info = 0;
switch (xfer_mode) {
case XFER_MW_DMA_2:
@@ -272,6 +272,8 @@ static int icside_set_speed(ide_drive_t
case XFER_SW_DMA_0:
cycle_time = 480;
break;
+ default:
+ return 1;
}
/*
@@ -283,17 +285,10 @@ static int icside_set_speed(ide_drive_t
drive->drive_data = cycle_time;
- if (cycle_time && ide_config_drive_speed(drive, xfer_mode) == 0)
- on = 1;
- else
- drive->drive_data = 480;
-
printk("%s: %s selected (peak %dMB/s)\n", drive->name,
ide_xfer_verbose(xfer_mode), 2000 / drive->drive_data);
- drive->current_speed = xfer_mode;
-
- return on;
+ return ide_config_drive_speed(drive, xfer_mode);
}
static void icside_dma_host_off(ide_drive_t *drive)
@@ -320,8 +315,7 @@ static int icside_dma_check(ide_drive_t
{
struct hd_driveid *id = drive->id;
ide_hwif_t *hwif = HWIF(drive);
- int xfer_mode = XFER_PIO_2;
- int on;
+ int xfer_mode = 0;
if (!(id->capability & 1) || !hwif->autodma)
goto out;
@@ -350,9 +344,10 @@ static int icside_dma_check(ide_drive_t
}
out:
- on = icside_set_speed(drive, xfer_mode);
+ if (xfer_mode == 0)
+ return -1;
- return on ? 0 : -1;
+ return icside_set_speed(drive, xfer_mode) ? -1 : 0;
}
static int icside_dma_end(ide_drive_t *drive)
-
To unsubscribe from this list: send the line "unsubscribe linux-ide" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
