* Add IDE_HFLAG_ABUSE_{PREFETCH,FAST_DEVSEL,DMA_MODES} flags
and set them in ht6560, cmd640, cmd64x and sc1200 host drivers.
* Add set_pio_mode_abuse() for checking if host driver has a non-standard
->tuneproc() implementation and use it in do_special().
* Add ide_set_pio() for setting PIO mode (it uses hwif->pio_mask to find
the maximum PIO mode supported by the host), also add ide_set_max_pio()
wrapper for ide_set_pio() to use for auto-tuning. Convert users of
->tuneproc to use ide_set{_max}_pio() where possible. This leaves only
do_special(), set_using_pio(), ide_hwif_restore() and ide_set_pio() as
a direct users of ->tuneproc.
* Remove no longer needed ide_get_best_pio_mode() calls and printk-s
reporting PIO mode selected from ->tuneproc implementations.
* Rename ->tuneproc hook to ->set_pio_mode and make 'pio' argument const.
* Remove stale comment from ide_config_drive_speed().
v2:
* Fix "ata_" prefix (Noticed by Jeff).
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@xxxxxxxxx>
Cc: Jeff Garzik <jeff@xxxxxxxxxx>
---
drivers/ide/cris/ide-cris.c | 6 ++--
drivers/ide/ide-io.c | 47 +++++++++++++++++++++++++++++---
drivers/ide/ide-iops.c | 6 ----
drivers/ide/ide-lib.c | 29 +++++++++++++++++++
drivers/ide/ide-probe.c | 6 +---
drivers/ide/ide.c | 5 ++-
drivers/ide/legacy/ali14xx.c | 10 ++----
drivers/ide/legacy/dtc2278.c | 6 +---
drivers/ide/legacy/ht6560b.c | 11 ++++---
drivers/ide/legacy/qd65xx.c | 60 ++++++++++++++++++++++-------------------
drivers/ide/legacy/umc8672.c | 7 ++--
drivers/ide/mips/au1xxx-ide.c | 12 ++------
drivers/ide/pci/aec62xx.c | 7 ++--
drivers/ide/pci/alim15x3.c | 28 +++++++------------
drivers/ide/pci/amd74xx.c | 14 +++------
drivers/ide/pci/atiixp.c | 7 ++--
drivers/ide/pci/cmd640.c | 25 ++++++++---------
drivers/ide/pci/cmd64x.c | 39 ++++++++++++--------------
drivers/ide/pci/cs5520.c | 11 +++----
drivers/ide/pci/cs5530.c | 10 ++----
drivers/ide/pci/cs5535.c | 24 ++++++----------
drivers/ide/pci/cy82c693.c | 20 +------------
drivers/ide/pci/hpt34x.c | 7 ++--
drivers/ide/pci/hpt366.c | 7 ++--
drivers/ide/pci/it8213.c | 15 ++++++----
drivers/ide/pci/it821x.c | 7 ++--
drivers/ide/pci/jmicron.c | 4 +-
drivers/ide/pci/opti621.c | 19 ++++++------
drivers/ide/pci/pdc202xx_new.c | 8 ++---
drivers/ide/pci/pdc202xx_old.c | 14 +++++----
drivers/ide/pci/piix.c | 22 ++++++++-------
drivers/ide/pci/sc1200.c | 14 ++++-----
drivers/ide/pci/scc_pata.c | 40 +++++++--------------------
drivers/ide/pci/serverworks.c | 7 ++--
drivers/ide/pci/sgiioc4.c | 2 -
drivers/ide/pci/siimage.c | 7 ++--
drivers/ide/pci/sis5513.c | 11 +++----
drivers/ide/pci/sl82c105.c | 17 +++--------
drivers/ide/pci/slc90e66.c | 7 ++--
drivers/ide/pci/tc86c001.c | 7 ++--
drivers/ide/pci/triflex.c | 9 ++----
drivers/ide/pci/via82cxxx.c | 16 ++++------
drivers/ide/ppc/mpc8xx.c | 21 ++------------
drivers/ide/ppc/pmac.c | 8 ++---
include/linux/ide.h | 18 ++++++++++--
45 files changed, 333 insertions(+), 344 deletions(-)
Index: b/drivers/ide/cris/ide-cris.c
===================================================================
--- a/drivers/ide/cris/ide-cris.c
+++ b/drivers/ide/cris/ide-cris.c
@@ -686,7 +686,7 @@ static void cris_dma_off(ide_drive_t *dr
{
}
-static void tune_cris_ide(ide_drive_t *drive, u8 pio)
+static void cris_set_pio_mode(ide_drive_t *drive, const u8 pio)
{
int setup, strobe, hold;
@@ -731,7 +731,7 @@ static int speed_cris_ide(ide_drive_t *d
int cyc = 0, dvs = 0, strobe = 0, hold = 0;
if (speed >= XFER_PIO_0 && speed <= XFER_PIO_4) {
- tune_cris_ide(drive, speed - XFER_PIO_0);
+ cris_set_pio_mode(drive, speed - XFER_PIO_0);
return ide_config_drive_speed(drive, speed);
}
@@ -801,7 +801,7 @@ init_e100_ide (void)
ide_register_hw(&hw, 1, &hwif);
hwif->mmio = 1;
hwif->chipset = ide_etrax100;
- hwif->tuneproc = &tune_cris_ide;
+ hwif->set_pio_mode = &cris_set_pio_mode;
hwif->speedproc = &speed_cris_ide;
hwif->ata_input_data = &cris_ide_input_data;
hwif->ata_output_data = &cris_ide_output_data;
Index: b/drivers/ide/ide-io.c
===================================================================
--- a/drivers/ide/ide-io.c
+++ b/drivers/ide/ide-io.c
@@ -196,8 +196,7 @@ static ide_startstop_t ide_start_power_s
return do_rw_taskfile(drive, args);
case idedisk_pm_restore_pio: /* Resume step 1 (restore PIO) */
- if (drive->hwif->tuneproc != NULL)
- drive->hwif->tuneproc(drive, 255);
+ ide_set_max_pio(drive);
/*
* skip idedisk_pm_idle for ATAPI devices
*/
@@ -783,6 +782,38 @@ static ide_startstop_t ide_disk_special(
return ide_started;
}
+/*
+ * handle HDIO_SET_PIO_MODE ioctl abusers here, eventually it will go away
+ */
+static int set_pio_mode_abuse(ide_hwif_t *hwif, u8 req_pio)
+{
+ int abuse;
+
+ switch (req_pio) {
+ case 202:
+ case 201:
+ case 200:
+ case 102:
+ case 101:
+ case 100:
+ abuse = (hwif->host_flags & IDE_HFLAG_ABUSE_DMA_MODES) ? 1 : 0;
+ break;
+ case 9:
+ case 8:
+ abuse = (hwif->host_flags & IDE_HFLAG_ABUSE_PREFETCH) ? 1 : 0;
+ break;
+ case 7:
+ case 6:
+ abuse = (hwif->host_flags & IDE_HFLAG_ABUSE_FAST_DEVSEL) ? 1 : 0;
+ break;
+ default:
+ abuse = 0;
+ break;
+ }
+
+ return abuse;
+}
+
/**
* do_special - issue some special commands
* @drive: drive the command is for
@@ -800,9 +831,17 @@ static ide_startstop_t do_special (ide_d
printk("%s: do_special: 0x%02x\n", drive->name, s->all);
#endif
if (s->b.set_tune) {
+ ide_hwif_t *hwif = drive->hwif;
+ u8 req_pio = drive->tune_req;
+
s->b.set_tune = 0;
- if (HWIF(drive)->tuneproc != NULL)
- HWIF(drive)->tuneproc(drive, drive->tune_req);
+
+ if (set_pio_mode_abuse(drive->hwif, req_pio)) {
+ if (hwif->set_pio_mode)
+ hwif->set_pio_mode(drive, req_pio);
+ } else
+ ide_set_pio(drive, req_pio);
+
return ide_stopped;
} else {
if (drive->media == ide_disk)
Index: b/drivers/ide/ide-iops.c
===================================================================
--- a/drivers/ide/ide-iops.c
+++ b/drivers/ide/ide-iops.c
@@ -746,12 +746,6 @@ int ide_driveid_update (ide_drive_t *dri
/*
* Similar to ide_wait_stat(), except it never calls ide_error internally.
- * This is a kludge to handle the new ide_config_drive_speed() function,
- * and should not otherwise be used anywhere. Eventually, the tuneproc's
- * should be updated to return ide_startstop_t, in which case we can get
- * rid of this abomination again. :) -ml
- *
- * It is gone..........
*
* const char *msg == consider adding for verbose errors.
*/
Index: b/drivers/ide/ide-lib.c
===================================================================
--- a/drivers/ide/ide-lib.c
+++ b/drivers/ide/ide-lib.c
@@ -340,6 +340,35 @@ u8 ide_get_best_pio_mode (ide_drive_t *d
EXPORT_SYMBOL_GPL(ide_get_best_pio_mode);
+/* req_pio == "255" for auto-tune */
+void ide_set_pio(ide_drive_t *drive, u8 req_pio)
+{
+ ide_hwif_t *hwif = drive->hwif;
+ u8 host_pio, pio;
+
+ if (hwif->set_pio_mode == NULL)
+ return;
+
+ BUG_ON(hwif->pio_mask == 0x00);
+
+ host_pio = fls(hwif->pio_mask) - 1;
+
+ pio = ide_get_best_pio_mode(drive, req_pio, host_pio);
+
+ /*
+ * TODO:
+ * - report device max PIO mode
+ * - check req_pio != 255 against device max PIO mode
+ */
+ printk(KERN_DEBUG "%s: host max PIO%d wanted PIO%d%s selected PIO%d\n",
+ drive->name, host_pio, req_pio,
+ req_pio == 255 ? "(auto-tune)" : "", pio);
+
+ hwif->set_pio_mode(drive, pio);
+}
+
+EXPORT_SYMBOL_GPL(ide_set_pio);
+
/**
* ide_toggle_bounce - handle bounce buffering
* @drive: drive to update
Index: b/drivers/ide/ide-probe.c
===================================================================
--- a/drivers/ide/ide-probe.c
+++ b/drivers/ide/ide-probe.c
@@ -827,10 +827,8 @@ static void probe_hwif(ide_hwif_t *hwif,
ide_drive_t *drive = &hwif->drives[unit];
if (drive->present) {
- if (hwif->tuneproc != NULL &&
- drive->autotune == IDE_TUNE_AUTO)
- /* auto-tune PIO mode */
- hwif->tuneproc(drive, 255);
+ if (drive->autotune == IDE_TUNE_AUTO)
+ ide_set_max_pio(drive);
if (drive->autotune != IDE_TUNE_DEFAULT &&
drive->autotune != IDE_TUNE_AUTO)
Index: b/drivers/ide/ide.c
===================================================================
--- a/drivers/ide/ide.c
+++ b/drivers/ide/ide.c
@@ -474,7 +474,7 @@ static void ide_hwif_restore(ide_hwif_t
hwif->cds = tmp_hwif->cds;
#endif
- hwif->tuneproc = tmp_hwif->tuneproc;
+ hwif->set_pio_mode = tmp_hwif->set_pio_mode;
hwif->speedproc = tmp_hwif->speedproc;
hwif->udma_filter = tmp_hwif->udma_filter;
hwif->selectproc = tmp_hwif->selectproc;
@@ -944,8 +944,9 @@ int set_pio_mode(ide_drive_t *drive, int
if (arg < 0 || arg > 255)
return -EINVAL;
- if (!HWIF(drive)->tuneproc)
+ if (drive->hwif->set_pio_mode == NULL)
return -ENOSYS;
+
if (drive->special.b.set_tune)
return -EBUSY;
ide_init_drive_cmd(&rq);
Index: b/drivers/ide/legacy/ali14xx.c
===================================================================
--- a/drivers/ide/legacy/ali14xx.c
+++ b/drivers/ide/legacy/ali14xx.c
@@ -68,8 +68,6 @@ static RegInitializer initData[] __initd
{0x35, 0x03}, {0x00, 0x00}
};
-#define ALI_MAX_PIO 4
-
/* timing parameter registers for each drive */
static struct { u8 reg1, reg2, reg3, reg4; } regTab[4] = {
{0x03, 0x26, 0x04, 0x27}, /* drive 0 */
@@ -109,7 +107,7 @@ static void outReg (u8 data, u8 reg)
* This function computes timing parameters
* and sets controller registers accordingly.
*/
-static void ali14xx_tune_drive (ide_drive_t *drive, u8 pio)
+static void ali14xx_set_pio_mode(ide_drive_t *drive, const u8 pio)
{
int driveNum;
int time1, time2;
@@ -117,8 +115,6 @@ static void ali14xx_tune_drive (ide_driv
unsigned long flags;
int bus_speed = system_bus_clock();
- pio = ide_get_best_pio_mode(drive, pio, ALI_MAX_PIO);
-
/* calculate timing, according to PIO mode */
time1 = ide_pio_cycle_time(drive, pio);
time2 = ide_pio_timings[pio].active_time;
@@ -212,12 +208,12 @@ static int __init ali14xx_probe(void)
hwif->chipset = ide_ali14xx;
hwif->pio_mask = ATA_PIO4;
- hwif->tuneproc = &ali14xx_tune_drive;
+ hwif->set_pio_mode = &ali14xx_set_pio_mode;
hwif->mate = mate;
mate->chipset = ide_ali14xx;
mate->pio_mask = ATA_PIO4;
- mate->tuneproc = &ali14xx_tune_drive;
+ mate->set_pio_mode = &ali14xx_set_pio_mode;
mate->mate = hwif;
mate->channel = 1;
Index: b/drivers/ide/legacy/dtc2278.c
===================================================================
--- a/drivers/ide/legacy/dtc2278.c
+++ b/drivers/ide/legacy/dtc2278.c
@@ -67,12 +67,10 @@ static void sub22 (char b, char c)
}
}
-static void tune_dtc2278 (ide_drive_t *drive, u8 pio)
+static void dtc2278_set_pio_mode(ide_drive_t *drive, const u8 pio)
{
unsigned long flags;
- pio = ide_get_best_pio_mode(drive, pio, 4);
-
if (pio >= 3) {
spin_lock_irqsave(&ide_lock, flags);
/*
@@ -124,7 +122,7 @@ static int __init dtc2278_probe(void)
hwif->serialized = 1;
hwif->chipset = ide_dtc2278;
hwif->pio_mask = ATA_PIO4;
- hwif->tuneproc = &tune_dtc2278;
+ hwif->set_pio_mode = &dtc2278_set_pio_mode;
hwif->drives[0].no_unmask = 1;
hwif->drives[1].no_unmask = 1;
hwif->mate = mate;
Index: b/drivers/ide/legacy/ht6560b.c
===================================================================
--- a/drivers/ide/legacy/ht6560b.c
+++ b/drivers/ide/legacy/ht6560b.c
@@ -199,7 +199,7 @@ static int __init try_to_init_ht6560b(vo
return 1;
}
-static u8 ht_pio2timings(ide_drive_t *drive, u8 pio)
+static u8 ht_pio2timings(ide_drive_t *drive, const u8 pio)
{
int active_time, recovery_time;
int active_cycles, recovery_cycles;
@@ -208,7 +208,6 @@ static u8 ht_pio2timings(ide_drive_t *dr
if (pio) {
unsigned int cycle_time;
- pio = ide_get_best_pio_mode(drive, pio, 5);
cycle_time = ide_pio_cycle_time(drive, pio);
/*
@@ -277,7 +276,7 @@ static void ht_set_prefetch(ide_drive_t
#endif
}
-static void tune_ht6560b (ide_drive_t *drive, u8 pio)
+static void ht6560b_set_pio_mode(ide_drive_t *drive, const u8 pio)
{
unsigned long flags;
u8 timing;
@@ -333,15 +332,17 @@ int __init ht6560b_init(void)
hwif->chipset = ide_ht6560b;
hwif->selectproc = &ht6560b_selectproc;
+ hwif->host_flags = IDE_HFLAG_ABUSE_PREFETCH;
hwif->pio_mask = ATA_PIO5;
- hwif->tuneproc = &tune_ht6560b;
+ hwif->set_pio_mode = &ht6560b_set_pio_mode;
hwif->serialized = 1; /* is this needed? */
hwif->mate = mate;
mate->chipset = ide_ht6560b;
mate->selectproc = &ht6560b_selectproc;
+ mate->host_flags = IDE_HFLAG_ABUSE_PREFETCH;
mate->pio_mask = ATA_PIO5;
- mate->tuneproc = &tune_ht6560b;
+ mate->set_pio_mode = &ht6560b_set_pio_mode;
mate->serialized = 1; /* is this needed? */
mate->mate = hwif;
mate->channel = 1;
Index: b/drivers/ide/legacy/qd65xx.c
===================================================================
--- a/drivers/ide/legacy/qd65xx.c
+++ b/drivers/ide/legacy/qd65xx.c
@@ -224,15 +224,14 @@ static void qd_set_timing (ide_drive_t *
printk(KERN_DEBUG "%s: %#x\n", drive->name, timing);
}
-/*
- * qd6500_tune_drive
- */
-
-static void qd6500_tune_drive (ide_drive_t *drive, u8 pio)
+static void qd6500_set_pio_mode(ide_drive_t *drive, const u8 pio)
{
int active_time = 175;
int recovery_time = 415; /* worst case values from the dos driver */
+ /*
+ * FIXME: use "pio" value
+ */
if (drive->id && !qd_find_disk_type(drive, &active_time, &recovery_time)
&& drive->id->tPIO && (drive->id->field_valid & 0x02)
&& drive->id->eide_pio >= 240) {
@@ -246,11 +245,7 @@ static void qd6500_tune_drive (ide_drive
qd_set_timing(drive, qd6500_compute_timing(HWIF(drive), active_time, recovery_time));
}
-/*
- * qd6580_tune_drive
- */
-
-static void qd6580_tune_drive (ide_drive_t *drive, u8 pio)
+static void qd6580_set_pio_mode(ide_drive_t *drive, const u8 pio)
{
int base = HWIF(drive)->select_data;
unsigned int cycle_time;
@@ -258,7 +253,6 @@ static void qd6580_tune_drive (ide_drive
int recovery_time = 415; /* worst case values from the dos driver */
if (drive->id && !qd_find_disk_type(drive, &active_time, &recovery_time)) {
- pio = ide_get_best_pio_mode(drive, pio, 4);
cycle_time = ide_pio_cycle_time(drive, pio);
switch (pio) {
@@ -335,8 +329,7 @@ static int __init qd_testreg(int port)
*/
static void __init qd_setup(ide_hwif_t *hwif, int base, int config,
- unsigned int data0, unsigned int data1,
- void (*tuneproc) (ide_drive_t *, u8 pio))
+ unsigned int data0, unsigned int data1)
{
hwif->chipset = ide_qd65xx;
hwif->channel = hwif->index;
@@ -347,8 +340,6 @@ static void __init qd_setup(ide_hwif_t *
hwif->drives[0].io_32bit =
hwif->drives[1].io_32bit = 1;
hwif->pio_mask = ATA_PIO4;
- hwif->tuneproc = tuneproc;
- probe_hwif_init(hwif);
}
/*
@@ -361,7 +352,7 @@ static void __exit qd_unsetup(ide_hwif_t
{
u8 config = hwif->config_data;
int base = hwif->select_data;
- void *tuneproc = (void *) hwif->tuneproc;
+ void *set_pio_mode = (void *)hwif->set_pio_mode;
if (hwif->chipset != ide_qd65xx)
return;
@@ -369,12 +360,12 @@ static void __exit qd_unsetup(ide_hwif_t
printk(KERN_NOTICE "%s: back to defaults\n", hwif->name);
hwif->selectproc = NULL;
- hwif->tuneproc = NULL;
+ hwif->set_pio_mode = NULL;
- if (tuneproc == (void *) qd6500_tune_drive) {
+ if (set_pio_mode == (void *)qd6500_tune_drive) {
// will do it for both
qd_write_reg(QD6500_DEF_DATA, QD_TIMREG(&hwif->drives[0]));
- } else if (tuneproc == (void *) qd6580_tune_drive) {
+ } else if (set_pio_mode == (void *)qd6580_tune_drive) {
if (QD_CONTROL(hwif) & QD_CONTR_SEC_DISABLED) {
qd_write_reg(QD6580_DEF_DATA, QD_TIMREG(&hwif->drives[0]));
qd_write_reg(QD6580_DEF_DATA2, QD_TIMREG(&hwif->drives[1]));
@@ -424,8 +415,11 @@ static int __init qd_probe(int base)
return 1;
}
- qd_setup(hwif, base, config, QD6500_DEF_DATA, QD6500_DEF_DATA,
- &qd6500_tune_drive);
+ qd_setup(hwif, base, config, QD6500_DEF_DATA, QD6500_DEF_DATA);
+
+ hwif->set_pio_mode = &qd6500_set_pio_mode;
+
+ probe_hwif_init(hwif);
ide_proc_register_port(hwif);
@@ -455,8 +449,12 @@ static int __init qd_probe(int base)
printk(KERN_INFO "%s: qd6580: single IDE board\n",
hwif->name);
qd_setup(hwif, base, config | (control << 8),
- QD6580_DEF_DATA, QD6580_DEF_DATA2,
- &qd6580_tune_drive);
+ QD6580_DEF_DATA, QD6580_DEF_DATA2);
+
+ hwif->set_pio_mode = &qd6580_set_pio_mode;
+
+ probe_hwif_init(hwif);
+
qd_write_reg(QD_DEF_CONTR,QD_CONTROL_PORT);
ide_proc_register_port(hwif);
@@ -472,11 +470,19 @@ static int __init qd_probe(int base)
hwif->name, mate->name);
qd_setup(hwif, base, config | (control << 8),
- QD6580_DEF_DATA, QD6580_DEF_DATA,
- &qd6580_tune_drive);
+ QD6580_DEF_DATA, QD6580_DEF_DATA);
+
+ hwif->set_pio_mode = &qd6580_set_pio_mode;
+
+ probe_hwif_init(hwif);
+
qd_setup(mate, base, config | (control << 8),
- QD6580_DEF_DATA2, QD6580_DEF_DATA2,
- &qd6580_tune_drive);
+ QD6580_DEF_DATA2, QD6580_DEF_DATA2);
+
+ mate->set_pio_mode = &qd6580_set_pio_mode;
+
+ probe_hwif_init(mate);
+
qd_write_reg(QD_DEF_CONTR,QD_CONTROL_PORT);
ide_proc_register_port(hwif);
Index: b/drivers/ide/legacy/umc8672.c
===================================================================
--- a/drivers/ide/legacy/umc8672.c
+++ b/drivers/ide/legacy/umc8672.c
@@ -105,12 +105,11 @@ static void umc_set_speeds (u8 speeds[])
speeds[0], speeds[1], speeds[2], speeds[3]);
}
-static void tune_umc (ide_drive_t *drive, u8 pio)
+static void umc_set_pio_mode(ide_drive_t *drive, const u8 pio)
{
unsigned long flags;
ide_hwgroup_t *hwgroup = ide_hwifs[HWIF(drive)->index^1].hwgroup;
- pio = ide_get_best_pio_mode(drive, pio, 4);
printk("%s: setting umc8672 to PIO mode%d (speed %d)\n",
drive->name, pio, pio_to_umc[pio]);
spin_lock_irqsave(&ide_lock, flags);
@@ -150,12 +149,12 @@ static int __init umc8672_probe(void)
hwif->chipset = ide_umc8672;
hwif->pio_mask = ATA_PIO4;
- hwif->tuneproc = &tune_umc;
+ hwif->set_pio_mode = &umc_set_pio_mode;
hwif->mate = mate;
mate->chipset = ide_umc8672;
mate->pio_mask = ATA_PIO4;
- mate->tuneproc = &tune_umc;
+ mate->set_pio_mode = &umc_set_pio_mode;
mate->mate = hwif;
mate->channel = 1;
Index: b/drivers/ide/mips/au1xxx-ide.c
===================================================================
--- a/drivers/ide/mips/au1xxx-ide.c
+++ b/drivers/ide/mips/au1xxx-ide.c
@@ -99,18 +99,12 @@ void auide_outsw(unsigned long port, voi
#endif
-static void auide_tune_drive(ide_drive_t *drive, byte pio)
+static void au1xxx_set_pio_mode(ide_drive_t *drive, const u8 pio)
{
int mem_sttime;
int mem_stcfg;
u8 speed;
- /* get the best pio mode for the drive */
- pio = ide_get_best_pio_mode(drive, pio, 4);
-
- printk(KERN_INFO "%s: setting Au1XXX IDE to PIO mode%d\n",
- drive->name, pio);
-
mem_sttime = 0;
mem_stcfg = au_readl(MEM_STCFG2);
@@ -184,7 +178,7 @@ static int auide_tune_chipset (ide_drive
mem_stcfg = au_readl(MEM_STCFG2);
if (speed >= XFER_PIO_0 && speed <= XFER_PIO_4) {
- auide_tune_drive(drive, speed - XFER_PIO_0);
+ au1xxx_set_pio_mode(drive, speed - XFER_PIO_0);
return 0;
}
@@ -712,7 +706,7 @@ static int au_ide_probe(struct device *d
hwif->OUTSW = auide_outsw;
#endif
- hwif->tuneproc = &auide_tune_drive;
+ hwif->set_pio_mode = &au1xxx_set_pio_mode;
hwif->speedproc = &auide_tune_chipset;
#ifdef CONFIG_BLK_DEV_IDE_AU1XXX_MDMA2_DBDMA
Index: b/drivers/ide/pci/aec62xx.c
===================================================================
--- a/drivers/ide/pci/aec62xx.c
+++ b/drivers/ide/pci/aec62xx.c
@@ -140,9 +140,8 @@ static int aec6260_tune_chipset (ide_dri
return(ide_config_drive_speed(drive, speed));
}
-static void aec62xx_tune_drive (ide_drive_t *drive, u8 pio)
+static void aec_set_pio_mode(ide_drive_t *drive, const u8 pio)
{
- pio = ide_get_best_pio_mode(drive, pio, 4);
(void) HWIF(drive)->speedproc(drive, pio + XFER_PIO_0);
}
@@ -152,7 +151,7 @@ static int aec62xx_config_drive_xfer_rat
return 0;
if (ide_use_fast_pio(drive))
- aec62xx_tune_drive(drive, 255);
+ ide_set_max_pio(drive);
return -1;
}
@@ -203,7 +202,7 @@ static void __devinit init_hwif_aec62xx(
u8 reg54 = 0, mask = hwif->channel ? 0xf0 : 0x0f;
unsigned long flags;
- hwif->tuneproc = &aec62xx_tune_drive;
+ hwif->set_pio_mode = &aec_set_pio_mode;
if (dev->device == PCI_DEVICE_ID_ARTOP_ATP850UF) {
if(hwif->mate)
Index: b/drivers/ide/pci/alim15x3.c
===================================================================
--- a/drivers/ide/pci/alim15x3.c
+++ b/drivers/ide/pci/alim15x3.c
@@ -283,17 +283,14 @@ static int ali_get_info (char *buffer, c
#endif /* defined(DISPLAY_ALI_TIMINGS) && defined(CONFIG_IDE_PROC_FS) */
/**
- * ali15x3_tune_pio - set up chipset for PIO mode
+ * ali_tune_pio - set up chipset for PIO mode
* @drive: drive to tune
* @pio: desired mode
*
- * Select the best PIO mode for the drive in question.
- * Then program the controller for this mode.
- *
- * Returns the PIO mode programmed.
+ * Program the controller for @pio PIO mode.
*/
-
-static u8 ali15x3_tune_pio (ide_drive_t *drive, u8 pio)
+
+void ali_tune_pio(ide_drive_t *drive, const u8 pio)
{
ide_hwif_t *hwif = HWIF(drive);
struct pci_dev *dev = hwif->pci_dev;
@@ -306,7 +303,6 @@ static u8 ali15x3_tune_pio (ide_drive_t
u8 cd_dma_fifo = 0;
int unit = drive->select.b.unit & 1;
- pio = ide_get_best_pio_mode(drive, pio, 5);
s_time = ide_pio_timings[pio].setup_time;
a_time = ide_pio_timings[pio].active_time;
if ((s_clc = (s_time * bus_speed + 999) / 1000) >= 8)
@@ -359,22 +355,20 @@ static u8 ali15x3_tune_pio (ide_drive_t
* { 25, 70, 25 }, PIO Mode 4 with IORDY ns
* { 20, 50, 30 } PIO Mode 5 with IORDY (nonstandard)
*/
-
- return pio;
}
/**
- * ali15x3_tune_drive - set up drive for PIO mode
+ * ali_set_pio_mode - set up drive for PIO mode
* @drive: drive to tune
* @pio: desired mode
*
- * Program the controller with the best PIO timing for the given drive.
+ * Program the controller with the desired PIO timing for the given drive.
* Then set up the drive itself.
*/
-static void ali15x3_tune_drive (ide_drive_t *drive, u8 pio)
+static void ali_set_pio_mode(ide_drive_t *drive, const u8 pio)
{
- pio = ali15x3_tune_pio(drive, pio);
+ ali_tune_pio(drive, pio);
(void) ide_config_drive_speed(drive, XFER_PIO_0 + pio);
}
@@ -453,7 +447,7 @@ static int ali15x3_tune_chipset (ide_dri
*/
if (speed < XFER_SW_DMA_0)
- (void) ali15x3_tune_pio(drive, speed - XFER_PIO_0);
+ ali_tune_pio(drive, speed - XFER_PIO_0);
} else {
pci_read_config_byte(dev, m5229_udma, &tmpbyte);
tmpbyte &= (0x0f << ((1-unit) << 2));
@@ -486,7 +480,7 @@ static int ali15x3_config_drive_for_dma(
if (ide_tune_dma(drive))
return 0;
- ali15x3_tune_drive(drive, 255);
+ ide_set_max_pio(drive);
return -1;
}
@@ -709,7 +703,7 @@ static u8 __devinit ata66_ali15x3(ide_hw
static void __devinit init_hwif_common_ali15x3 (ide_hwif_t *hwif)
{
hwif->autodma = 0;
- hwif->tuneproc = &ali15x3_tune_drive;
+ hwif->set_pio_mode = &ali_set_pio_mode;
hwif->speedproc = &ali15x3_tune_chipset;
hwif->udma_filter = &ali_udma_filter;
Index: b/drivers/ide/pci/amd74xx.c
===================================================================
--- a/drivers/ide/pci/amd74xx.c
+++ b/drivers/ide/pci/amd74xx.c
@@ -269,16 +269,12 @@ static int amd_set_drive(ide_drive_t *dr
}
/*
- * amd74xx_tune_drive() is a callback from upper layers for
- * PIO-only tuning.
+ * amd_set_pio_mode() is a callback from upper layers for PIO-only tuning.
*/
-static void amd74xx_tune_drive(ide_drive_t *drive, u8 pio)
+static void amd_set_pio_mode(ide_drive_t *drive, const u8 pio)
{
- if (pio == 255)
- pio = ide_get_best_pio_mode(drive, 255, 5);
-
- amd_set_drive(drive, XFER_PIO_0 + min_t(byte, pio, 5));
+ amd_set_drive(drive, XFER_PIO_0 + pio);
}
static int amd74xx_ide_dma_check(ide_drive_t *drive)
@@ -286,7 +282,7 @@ static int amd74xx_ide_dma_check(ide_dri
u8 speed = ide_max_dma_mode(drive);
if (speed == 0) {
- amd74xx_tune_drive(drive, 255);
+ ide_set_max_pio(drive);
return -1;
}
@@ -413,7 +409,7 @@ static void __devinit init_hwif_amd74xx(
hwif->autodma = 0;
- hwif->tuneproc = &amd74xx_tune_drive;
+ hwif->set_pio_mode = &amd_set_pio_mode;
hwif->speedproc = &amd_set_drive;
for (i = 0; i < 2; i++) {
Index: b/drivers/ide/pci/atiixp.c
===================================================================
--- a/drivers/ide/pci/atiixp.c
+++ b/drivers/ide/pci/atiixp.c
@@ -153,9 +153,8 @@ static void atiixp_tune_pio(ide_drive_t
spin_unlock_irqrestore(&atiixp_lock, flags);
}
-static void atiixp_tuneproc(ide_drive_t *drive, u8 pio)
+static void atiixp_set_pio_mode(ide_drive_t *drive, const u8 pio)
{
- pio = ide_get_best_pio_mode(drive, pio, 4);
atiixp_tune_pio(drive, pio);
(void)ide_config_drive_speed(drive, XFER_PIO_0 + pio);
}
@@ -244,7 +243,7 @@ static int atiixp_dma_check(ide_drive_t
return 0;
if (ide_use_fast_pio(drive))
- atiixp_tuneproc(drive, 255);
+ ide_set_max_pio(drive);
return -1;
}
@@ -267,7 +266,7 @@ static void __devinit init_hwif_atiixp(i
hwif->irq = ch ? 15 : 14;
hwif->autodma = 0;
- hwif->tuneproc = &atiixp_tuneproc;
+ hwif->set_pio_mode = &atiixp_set_pio_mode;
hwif->speedproc = &atiixp_speedproc;
hwif->drives[0].autotune = 1;
hwif->drives[1].autotune = 1;
Index: b/drivers/ide/pci/cmd640.c
===================================================================
--- a/drivers/ide/pci/cmd640.c
+++ b/drivers/ide/pci/cmd640.c
@@ -628,21 +628,19 @@ static void cmd640_set_mode (unsigned in
program_drive_counts (index);
}
-/*
- * Drive PIO mode selection:
- */
-static void cmd640_tune_drive (ide_drive_t *drive, u8 mode_wanted)
+static void cmd640_set_pio_mode(ide_drive_t *drive, const u8 pio)
{
unsigned int index = 0, cycle_time;
u8 b;
while (drive != cmd_drives[index]) {
if (++index > 3) {
- printk("%s: bad news in cmd640_tune_drive\n", drive->name);
+ printk(KERN_ERR "%s: bad news in %s\n",
+ drive->name, __FUNCTION__);
return;
}
}
- switch (mode_wanted) {
+ switch (pio) {
case 6: /* set fast-devsel off */
case 7: /* set fast-devsel on */
mode_wanted &= 1;
@@ -661,12 +659,11 @@ static void cmd640_tune_drive (ide_drive
return;
}
- mode_wanted = ide_get_best_pio_mode(drive, mode_wanted, 5);
- cycle_time = ide_pio_cycle_time(drive, mode_wanted);
- cmd640_set_mode(index, mode_wanted, cycle_time);
+ cycle_time = ide_pio_cycle_time(drive, pio);
+ cmd640_set_mode(index, pio, cycle_time);
printk("%s: selected cmd640 PIO mode%d (%dns)",
- drive->name, mode_wanted, cycle_time);
+ drive->name, pio, cycle_time);
display_clocks(index);
}
@@ -766,8 +763,10 @@ int __init ide_probe_for_cmd640x (void)
cmd_hwif0->name, 'a' + cmd640_chip_version - 1, bus_type, cfr);
cmd_hwif0->chipset = ide_cmd640;
#ifdef CONFIG_BLK_DEV_CMD640_ENHANCED
+ cmd_hwif0->host_flags = IDE_HFLAG_ABUSE_PREFETCH |
+ IDE_HFLAG_ABUSE_FAST_DEVSEL;
cmd_hwif0->pio_mask = ATA_PIO5;
- cmd_hwif0->tuneproc = &cmd640_tune_drive;
+ cmd_hwif0->set_pio_mode = &cmd640_set_pio_mode;
#endif /* CONFIG_BLK_DEV_CMD640_ENHANCED */
/*
@@ -822,8 +821,10 @@ int __init ide_probe_for_cmd640x (void)
cmd_hwif1->mate = cmd_hwif0;
cmd_hwif1->channel = 1;
#ifdef CONFIG_BLK_DEV_CMD640_ENHANCED
+ cmd_hwif1->host_flags = IDE_HFLAG_ABUSE_PREFETCH |
+ IDE_HFLAG_ABUSE_FAST_DEVSEL;
cmd_hwif1->pio_mask = ATA_PIO5;
- cmd_hwif1->tuneproc = &cmd640_tune_drive;
+ cmd_hwif1->set_pio_mode = &cmd640_set_pio_mode;
#endif /* CONFIG_BLK_DEV_CMD640_ENHANCED */
}
printk(KERN_INFO "%s: %sserialized, secondary interface %s\n", cmd_hwif1->name,
Index: b/drivers/ide/pci/cmd64x.c
===================================================================
--- a/drivers/ide/pci/cmd64x.c
+++ b/drivers/ide/pci/cmd64x.c
@@ -216,28 +216,25 @@ static void program_cycle_times (ide_dri
}
/*
- * This routine selects drive's best PIO mode and writes into the chipset
- * registers setup/active/recovery timings.
+ * This routine writes into the chipset registers
+ * PIO setup/active/recovery timings.
*/
-static u8 cmd64x_tune_pio (ide_drive_t *drive, u8 mode_wanted)
+static void cmd64x_tune_pio(ide_drive_t *drive, const u8 pio)
{
ide_hwif_t *hwif = HWIF(drive);
struct pci_dev *dev = hwif->pci_dev;
unsigned int cycle_time;
- u8 pio_mode, setup_count, arttim = 0;
+ u8 setup_count, arttim = 0;
+
static const u8 setup_values[] = {0x40, 0x40, 0x40, 0x80, 0, 0xc0};
static const u8 arttim_regs[4] = {ARTTIM0, ARTTIM1, ARTTIM23, ARTTIM23};
- pio_mode = ide_get_best_pio_mode(drive, mode_wanted, 5);
- cycle_time = ide_pio_cycle_time(drive, pio_mode);
-
- cmdprintk("%s: PIO mode wanted %d, selected %d (%d ns)\n",
- drive->name, mode_wanted, pio_mode, cycle_time);
+ cycle_time = ide_pio_cycle_time(drive, pio);
program_cycle_times(drive, cycle_time,
- ide_pio_timings[pio_mode].active_time);
+ ide_pio_timings[pio].active_time);
- setup_count = quantize_timing(ide_pio_timings[pio_mode].setup_time,
+ setup_count = quantize_timing(ide_pio_timings[pio].setup_time,
1000 / system_bus_clock());
/*
@@ -268,16 +265,14 @@ static u8 cmd64x_tune_pio (ide_drive_t *
arttim |= setup_values[setup_count];
(void) pci_write_config_byte(dev, arttim_regs[drive->dn], arttim);
cmdprintk("Write 0x%02x to reg 0x%x\n", arttim, arttim_regs[drive->dn]);
-
- return pio_mode;
}
/*
* Attempts to set drive's PIO mode.
- * Special cases are 8: prefetch off, 9: prefetch on (both never worked),
- * and 255: auto-select best mode (used at boot time).
+ * Special cases are 8: prefetch off, 9: prefetch on (both never worked)
*/
-static void cmd64x_tune_drive (ide_drive_t *drive, u8 pio)
+
+static void cmd64x_set_pio_mode(ide_drive_t *drive, const u8 pio)
{
/*
* Filter out the prefetch control values
@@ -286,7 +281,7 @@ static void cmd64x_tune_drive (ide_drive
if (pio == 8 || pio == 9)
return;
- pio = cmd64x_tune_pio(drive, pio);
+ cmd64x_tune_pio(drive, pio);
(void) ide_config_drive_speed(drive, XFER_PIO_0 + pio);
}
@@ -338,7 +333,7 @@ static int cmd64x_tune_chipset (ide_driv
case XFER_PIO_2:
case XFER_PIO_1:
case XFER_PIO_0:
- (void) cmd64x_tune_pio(drive, speed - XFER_PIO_0);
+ cmd64x_tune_pio(drive, speed - XFER_PIO_0);
break;
default:
return 1;
@@ -356,7 +351,7 @@ static int cmd64x_config_drive_for_dma (
return 0;
if (ide_use_fast_pio(drive))
- cmd64x_tune_drive(drive, 255);
+ ide_set_max_pio(drive);
return -1;
}
@@ -540,7 +535,7 @@ static void __devinit init_hwif_cmd64x(i
pci_read_config_byte(dev, PCI_REVISION_ID, &rev);
- hwif->tuneproc = &cmd64x_tune_drive;
+ hwif->set_pio_mode = &cmd64x_set_pio_mode;
hwif->speedproc = &cmd64x_tune_chipset;
hwif->drives[0].autotune = hwif->drives[1].autotune = 1;
@@ -627,6 +622,7 @@ static ide_pci_device_t cmd64x_chipsets[
.autodma = AUTODMA,
.enablebits = {{0x00,0x00,0x00}, {0x51,0x08,0x08}},
.bootable = ON_BOARD,
+ .host_flags = IDE_HFLAG_ABUSE_PREFETCH,
.pio_mask = ATA_PIO5,
.udma_mask = 0x00, /* no udma */
},{ /* 1 */
@@ -637,6 +633,7 @@ static ide_pci_device_t cmd64x_chipsets[
.autodma = AUTODMA,
.enablebits = {{0x51,0x04,0x04}, {0x51,0x08,0x08}},
.bootable = ON_BOARD,
+ .host_flags = IDE_HFLAG_ABUSE_PREFETCH,
.pio_mask = ATA_PIO5,
.udma_mask = 0x07, /* udma0-2 */
},{ /* 2 */
@@ -647,6 +644,7 @@ static ide_pci_device_t cmd64x_chipsets[
.autodma = AUTODMA,
.enablebits = {{0x51,0x04,0x04}, {0x51,0x08,0x08}},
.bootable = ON_BOARD,
+ .host_flags = IDE_HFLAG_ABUSE_PREFETCH,
.pio_mask = ATA_PIO5,
.udma_mask = 0x1f, /* udma0-4 */
},{ /* 3 */
@@ -657,6 +655,7 @@ static ide_pci_device_t cmd64x_chipsets[
.autodma = AUTODMA,
.enablebits = {{0x51,0x04,0x04}, {0x51,0x08,0x08}},
.bootable = ON_BOARD,
+ .host_flags = IDE_HFLAG_ABUSE_PREFETCH,
.pio_mask = ATA_PIO5,
.udma_mask = 0x3f, /* udma0-5 */
}
Index: b/drivers/ide/pci/cs5520.c
===================================================================
--- a/drivers/ide/pci/cs5520.c
+++ b/drivers/ide/pci/cs5520.c
@@ -123,17 +123,16 @@ static int cs5520_tune_chipset(ide_drive
return error;
}
-
-static void cs5520_tune_drive(ide_drive_t *drive, u8 pio)
+
+static void cs5520_set_pio_mode(ide_drive_t *drive, const u8 pio)
{
- pio = ide_get_best_pio_mode(drive, pio, 4);
cs5520_tune_chipset(drive, (XFER_PIO_0 + pio));
}
static int cs5520_config_drive_xfer_rate(ide_drive_t *drive)
{
- /* Tune the drive for PIO modes up to PIO 4 */
- cs5520_tune_drive(drive, 4);
+ /* FIXME: tune the drive for PIO modes up to PIO 4 */
+ cs5520_set_pio_mode(drive, 4);
/* Then tell the core to use DMA operations */
return 0;
@@ -165,7 +164,7 @@ static int cs5520_dma_on(ide_drive_t *dr
static void __devinit init_hwif_cs5520(ide_hwif_t *hwif)
{
- hwif->tuneproc = &cs5520_tune_drive;
+ hwif->set_pio_mode = &cs5520_set_pio_mode;
hwif->speedproc = &cs5520_tune_chipset;
hwif->ide_dma_check = &cs5520_config_drive_xfer_rate;
hwif->ide_dma_on = &cs5520_dma_on;
Index: b/drivers/ide/pci/cs5530.c
===================================================================
--- a/drivers/ide/pci/cs5530.c
+++ b/drivers/ide/pci/cs5530.c
@@ -71,19 +71,17 @@ static void cs5530_tunepio(ide_drive_t *
}
/**
- * cs5530_tuneproc - select/set PIO modes
+ * cs5530_set_pio_mode - set PIO mode
*
- * cs5530_tuneproc() handles selection/setting of PIO modes
+ * cs5530_set_pio_mode() handles setting of PIO mode
* for both the chipset and drive.
*
* The ide_init_cs5530() routine guarantees that all drives
* will have valid default PIO timings set up before we get here.
*/
-static void cs5530_tuneproc (ide_drive_t *drive, u8 pio) /* pio=255 means "autotune" */
+static void cs5530_set_pio_mode(ide_drive_t *drive, const u8 pio)
{
- pio = ide_get_best_pio_mode(drive, pio, 4);
-
if (cs5530_set_xfer_mode(drive, XFER_PIO_0 + pio) == 0)
cs5530_tunepio(drive, pio);
}
@@ -305,7 +303,7 @@ static void __devinit init_hwif_cs5530 (
if (hwif->mate)
hwif->serialized = hwif->mate->serialized = 1;
- hwif->tuneproc = &cs5530_tuneproc;
+ hwif->set_pio_mode = &cs5530_set_pio_mode;
hwif->speedproc = &cs5530_tune_chipset;
basereg = CS5530_BASEREG(hwif);
Index: b/drivers/ide/pci/cs5535.c
===================================================================
--- a/drivers/ide/pci/cs5535.c
+++ b/drivers/ide/pci/cs5535.c
@@ -144,24 +144,20 @@ static int cs5535_set_drive(ide_drive_t
return 0;
}
-/****
- * cs5535_tuneproc - PIO setup
+/**
+ * cs5535_set_pio_mode - PIO setup
+ *
* @drive: drive to set up
- * @pio: mode to use (255 for 'best possible')
+ * @pio: PIO mode to use
*
* A callback from the upper layers for PIO-only tuning.
*/
-static void cs5535_tuneproc(ide_drive_t *drive, u8 xferspeed)
-{
- u8 modes[] = { XFER_PIO_0, XFER_PIO_1, XFER_PIO_2, XFER_PIO_3,
- XFER_PIO_4 };
- /* cs5535 max pio is pio 4, best_pio will check the blacklist.
- i think we don't need to rate_filter the incoming xferspeed
- since we know we're only going to choose pio */
- xferspeed = ide_get_best_pio_mode(drive, xferspeed, 4);
- ide_config_drive_speed(drive, modes[xferspeed]);
- cs5535_set_speed(drive, xferspeed);
+static void cs5535_set_pio_mode(ide_drive_t *drive, const u8 pio)
+{
+ ide_config_drive_speed(drive, XFER_PIO_0 + pio);
+ /* FIXME: "XFER_PIO_0 + pio" should be passed instead of "pio" */
+ cs5535_set_speed(drive, pio);
}
static int cs5535_dma_check(ide_drive_t *drive)
@@ -205,7 +201,7 @@ static void __devinit init_hwif_cs5535(i
hwif->autodma = 0;
- hwif->tuneproc = &cs5535_tuneproc;
+ hwif->set_pio_mode = &cs5535_set_pio_mode;
hwif->speedproc = &cs5535_set_drive;
hwif->ide_dma_check = &cs5535_dma_check;
Index: b/drivers/ide/pci/cy82c693.c
===================================================================
--- a/drivers/ide/pci/cy82c693.c
+++ b/drivers/ide/pci/cy82c693.c
@@ -97,9 +97,6 @@
#define CY82_INDEX_CHANNEL1 0x31
#define CY82_INDEX_TIMEOUT 0x32
-/* the max PIO mode - from datasheet */
-#define CY82C693_MAX_PIO 4
-
/* the min and max PCI bus speed in MHz - from datasheet */
#define CY82C963_MIN_BUS_SPEED 25
#define CY82C963_MAX_BUS_SPEED 33
@@ -148,9 +145,6 @@ static void compute_clocks (u8 pio, pio_
* so you can play with the idebus=xx parameter
*/
- if (pio > CY82C693_MAX_PIO)
- pio = CY82C693_MAX_PIO;
-
/* let's calc the address setup time clocks */
p_pclk->address_time = (u8)calc_clk(ide_pio_timings[pio].setup_time, bus_speed);
@@ -269,10 +263,7 @@ static int cy82c693_ide_dma_on (ide_driv
return __ide_dma_on(drive);
}
-/*
- * tune ide drive - set PIO mode
- */
-static void cy82c693_tune_drive (ide_drive_t *drive, u8 pio)
+static void cy82c693_set_pio_mode(ide_drive_t *drive, const u8 pio)
{
ide_hwif_t *hwif = HWIF(drive);
struct pci_dev *dev = hwif->pci_dev;
@@ -329,13 +320,6 @@ static void cy82c693_tune_drive (ide_dri
addrCtrl, pclk.time_16r, pclk.time_16w, pclk.time_8);
#endif /* CY82C693_DEBUG_LOGS */
- /* first let's calc the pio modes */
- pio = ide_get_best_pio_mode(drive, pio, CY82C693_MAX_PIO);
-
-#if CY82C693_DEBUG_INFO
- printk (KERN_INFO "%s: Selected PIO mode %d\n", drive->name, pio);
-#endif /* CY82C693_DEBUG_INFO */
-
/* let's calc the values for this PIO mode */
compute_clocks(pio, &pclk);
@@ -447,7 +431,7 @@ static void __devinit init_hwif_cy82c693
hwif->autodma = 0;
hwif->chipset = ide_cy82c693;
- hwif->tuneproc = &cy82c693_tune_drive;
+ hwif->set_pio_mode = &cy82c693_set_pio_mode;
if (!hwif->dma_base) {
hwif->drives[0].autotune = 1;
Index: b/drivers/ide/pci/hpt34x.c
===================================================================
--- a/drivers/ide/pci/hpt34x.c
+++ b/drivers/ide/pci/hpt34x.c
@@ -78,9 +78,8 @@ static int hpt34x_tune_chipset (ide_driv
return(ide_config_drive_speed(drive, speed));
}
-static void hpt34x_tune_drive (ide_drive_t *drive, u8 pio)
+static void hpt34x_set_pio_mode(ide_drive_t *drive, const u8 pio)
{
- pio = ide_get_best_pio_mode(drive, pio, 5);
(void) hpt34x_tune_chipset(drive, (XFER_PIO_0 + pio));
}
@@ -96,7 +95,7 @@ static int hpt34x_config_drive_xfer_rate
#endif
if (ide_use_fast_pio(drive))
- hpt34x_tune_drive(drive, 255);
+ ide_set_max_pio(drive);
return -1;
}
@@ -150,7 +149,7 @@ static void __devinit init_hwif_hpt34x(i
hwif->autodma = 0;
- hwif->tuneproc = &hpt34x_tune_drive;
+ hwif->set_pio_mode = &hpt34x_set_pio_mode;
hwif->speedproc = &hpt34x_tune_chipset;
hwif->drives[0].autotune = 1;
hwif->drives[1].autotune = 1;
Index: b/drivers/ide/pci/hpt366.c
===================================================================
--- a/drivers/ide/pci/hpt366.c
+++ b/drivers/ide/pci/hpt366.c
@@ -650,9 +650,8 @@ static int hpt3xx_tune_chipset(ide_drive
return hpt36x_tune_chipset(drive, speed);
}
-static void hpt3xx_tune_drive(ide_drive_t *drive, u8 pio)
+static void hpt3xx_set_pio_mode(ide_drive_t *drive, const u8 pio)
{
- pio = ide_get_best_pio_mode(drive, pio, 4);
(void) hpt3xx_tune_chipset (drive, XFER_PIO_0 + pio);
}
@@ -714,7 +713,7 @@ static int hpt366_config_drive_xfer_rate
return 0;
if (ide_use_fast_pio(drive))
- hpt3xx_tune_drive(drive, 255);
+ ide_set_max_pio(drive);
return -1;
}
@@ -1228,7 +1227,7 @@ static void __devinit init_hwif_hpt366(i
/* Cache the channel's MISC. control registers' offset */
hwif->select_data = hwif->channel ? 0x54 : 0x50;
- hwif->tuneproc = &hpt3xx_tune_drive;
+ hwif->set_pio_mode = &hpt3xx_set_pio_mode;
hwif->speedproc = &hpt3xx_tune_chipset;
hwif->quirkproc = &hpt3xx_quirkproc;
hwif->intrproc = &hpt3xx_intrproc;
Index: b/drivers/ide/pci/it8213.c
===================================================================
--- a/drivers/ide/pci/it8213.c
+++ b/drivers/ide/pci/it8213.c
@@ -4,6 +4,8 @@
* Copyright (C) 2006 Jack Lee
* Copyright (C) 2006 Alan Cox
* Copyright (C) 2007 Bartlomiej Zolnierkiewicz
+ *
+ * TODO: make ->set_pio_mode method set transfer mode on the device
*/
#include <linux/kernel.h>
@@ -55,14 +57,15 @@ static u8 it8213_dma_2_pio (u8 xfer_rate
}
/*
- * it8213_tuneproc - tune a drive
+ * it8213_set_pio_mode - set PIO mode
+ *
* @drive: drive to tune
* @pio: desired PIO mode
*
* Set the interface PIO mode.
*/
-static void it8213_tuneproc (ide_drive_t *drive, u8 pio)
+static void it8213_set_pio_mode(ide_drive_t *drive, const u8 pio)
{
ide_hwif_t *hwif = HWIF(drive);
struct pci_dev *dev = hwif->pci_dev;
@@ -82,8 +85,6 @@ static void it8213_tuneproc (ide_drive_t
{ 2, 1 },
{ 2, 3 }, };
- pio = ide_get_best_pio_mode(drive, pio, 4);
-
spin_lock_irqsave(&tune_lock, flags);
pci_read_config_word(dev, master_port, &master_data);
@@ -193,7 +194,9 @@ static int it8213_tune_chipset (ide_driv
if (reg55 & w_flag)
pci_write_config_byte(dev, 0x55, (u8) reg55 & ~w_flag);
}
- it8213_tuneproc(drive, it8213_dma_2_pio(speed));
+
+ it8213_set_pio_mode(drive, it8213_dma_2_pio(speed));
+
return ide_config_drive_speed(drive, speed);
}
@@ -234,7 +237,7 @@ static void __devinit init_hwif_it8213(i
u8 reg42h = 0;
hwif->speedproc = &it8213_tune_chipset;
- hwif->tuneproc = &it8213_tuneproc;
+ hwif->set_pio_mode = &it8213_set_pio_mode;
hwif->autodma = 0;
Index: b/drivers/ide/pci/it821x.c
===================================================================
--- a/drivers/ide/pci/it821x.c
+++ b/drivers/ide/pci/it821x.c
@@ -274,9 +274,8 @@ static int it821x_tunepio(ide_drive_t *d
return ide_config_drive_speed(drive, XFER_PIO_0 + set_pio);
}
-static void it821x_tuneproc(ide_drive_t *drive, u8 pio)
+static void it821x_set_pio_mode(ide_drive_t *drive, const u8 pio)
{
- pio = ide_get_best_pio_mode(drive, pio, 4);
(void)it821x_tunepio(drive, pio);
}
@@ -477,7 +476,7 @@ static int it821x_config_drive_for_dma (
if (ide_tune_dma(drive))
return 0;
- it821x_tuneproc(drive, 255);
+ ide_set_max_pio(drive);
return -1;
}
@@ -644,7 +643,7 @@ static void __devinit init_hwif_it821x(i
}
hwif->speedproc = &it821x_tune_chipset;
- hwif->tuneproc = &it821x_tuneproc;
+ hwif->set_pio_mode = &it821x_set_pio_mode;
/* MWDMA/PIO clock switching for pass through mode */
if(!idev->smart) {
Index: b/drivers/ide/pci/jmicron.c
===================================================================
--- a/drivers/ide/pci/jmicron.c
+++ b/drivers/ide/pci/jmicron.c
@@ -83,7 +83,7 @@ static u8 __devinit ata66_jmicron(ide_hw
return ATA_CBL_PATA80;
}
-static void jmicron_tuneproc (ide_drive_t *drive, byte mode_wanted)
+static void jmicron_set_pio_mode(ide_drive_t *drive, const u8 pio)
{
return;
}
@@ -147,7 +147,7 @@ static int jmicron_config_drive_for_dma
static void __devinit init_hwif_jmicron(ide_hwif_t *hwif)
{
hwif->speedproc = &jmicron_tune_chipset;
- hwif->tuneproc = &jmicron_tuneproc;
+ hwif->set_pio_mode = &jmicron_set_pio_mode;
hwif->drives[0].autotune = 1;
hwif->drives[1].autotune = 1;
Index: b/drivers/ide/pci/opti621.c
===================================================================
--- a/drivers/ide/pci/opti621.c
+++ b/drivers/ide/pci/opti621.c
@@ -47,7 +47,7 @@
* The main problem with OPTi is that some timings for master
* and slave must be the same. For example, if you have master
* PIO 3 and slave PIO 0, driver have to set some timings of
- * master for PIO 0. Second problem is that opti621_tune_drive
+ * master for PIO 0. Second problem is that opti621_set_pio_mode
* got only one drive to set, but have to set both drives.
* This is solved in compute_pios. If you don't set
* the second drive, compute_pios use ide_get_best_pio_mode
@@ -103,7 +103,7 @@
#include <asm/io.h>
-#define OPTI621_MAX_PIO 3
+//#define OPTI621_MAX_PIO 3
/* In fact, I do not have any PIO 4 drive
* (address: 25 ns, data: 70 ns, recovery: 35 ns),
* but OPTi 82C621 is programmable and it can do (minimal values):
@@ -136,8 +136,8 @@ static int reg_base;
#define PIO_NOT_EXIST 254
#define PIO_DONT_KNOW 255
-/* there are stored pio numbers from other calls of opti621_tune_drive */
-static void compute_pios(ide_drive_t *drive, u8 pio)
+/* there are stored pio numbers from other calls of opti621_set_pio_mode */
+static void compute_pios(ide_drive_t *drive, const u8 pio)
/* Store values into drive->drive_data
* second_contr - 0 for primary controller, 1 for secondary
* slave_drive - 0 -> pio is for master, 1 -> pio is for slave
@@ -147,12 +147,13 @@ static void compute_pios(ide_drive_t *dr
int d;
ide_hwif_t *hwif = HWIF(drive);
- drive->drive_data = ide_get_best_pio_mode(drive, pio, OPTI621_MAX_PIO);
+ drive->drive_data = pio;
+
for (d = 0; d < 2; ++d) {
drive = &hwif->drives[d];
if (drive->present) {
if (drive->drive_data == PIO_DONT_KNOW)
- drive->drive_data = ide_get_best_pio_mode(drive, 255, OPTI621_MAX_PIO);
+ drive->drive_data = ide_get_best_pio_mode(drive, 255, 3);
#ifdef OPTI621_DEBUG
printk("%s: Selected PIO mode %d\n",
drive->name, drive->drive_data);
@@ -240,8 +241,7 @@ static void compute_clocks(int pio, pio_
}
-/* Main tune procedure, called from tuneproc. */
-static void opti621_tune_drive (ide_drive_t *drive, u8 pio)
+static void opti621_set_pio_mode(ide_drive_t *drive, const u8 pio)
{
/* primary and secondary drives share some registers,
* so we have to program both drives
@@ -331,7 +331,8 @@ static void __devinit init_hwif_opti621
hwif->autodma = 0;
hwif->drives[0].drive_data = PIO_DONT_KNOW;
hwif->drives[1].drive_data = PIO_DONT_KNOW;
- hwif->tuneproc = &opti621_tune_drive;
+
+ hwif->set_pio_mode = &opti621_set_pio_mode;
if (!(hwif->dma_base))
return;
Index: b/drivers/ide/pci/pdc202xx_new.c
===================================================================
--- a/drivers/ide/pci/pdc202xx_new.c
+++ b/drivers/ide/pci/pdc202xx_new.c
@@ -217,9 +217,8 @@ static int pdcnew_tune_chipset(ide_drive
return err;
}
-static void pdcnew_tune_drive(ide_drive_t *drive, u8 pio)
+static void pdc_set_pio_mode(ide_drive_t *drive, const u8 pio)
{
- pio = ide_get_best_pio_mode(drive, pio, 4);
(void)pdcnew_tune_chipset(drive, XFER_PIO_0 + pio);
}
@@ -239,7 +238,7 @@ static int pdcnew_config_drive_xfer_rate
return 0;
if (ide_use_fast_pio(drive))
- pdcnew_tune_drive(drive, 255);
+ ide_set_max_pio(drive);
return -1;
}
@@ -483,7 +482,8 @@ static void __devinit init_hwif_pdc202ne
{
hwif->autodma = 0;
- hwif->tuneproc = &pdcnew_tune_drive;
+ hwif->set_pio_mode = &pdc_set_pio_mode;
+
hwif->quirkproc = &pdcnew_quirkproc;
hwif->speedproc = &pdcnew_tune_chipset;
hwif->resetproc = &pdcnew_reset;
Index: b/drivers/ide/pci/pdc202xx_old.c
===================================================================
--- a/drivers/ide/pci/pdc202xx_old.c
+++ b/drivers/ide/pci/pdc202xx_old.c
@@ -143,9 +143,8 @@ static int pdc202xx_tune_chipset (ide_dr
return ide_config_drive_speed(drive, speed);
}
-static void pdc202xx_tune_drive(ide_drive_t *drive, u8 pio)
+static void pdc_set_pio_mode(ide_drive_t *drive, const u8 pio)
{
- pio = ide_get_best_pio_mode(drive, pio, 4);
pdc202xx_tune_chipset(drive, XFER_PIO_0 + pio);
}
@@ -191,7 +190,7 @@ static int pdc202xx_config_drive_xfer_ra
return 0;
if (ide_use_fast_pio(drive))
- pdc202xx_tune_drive(drive, 255);
+ ide_set_max_pio(drive);
return -1;
}
@@ -307,10 +306,11 @@ static void pdc202xx_reset (ide_drive_t
{
ide_hwif_t *hwif = HWIF(drive);
ide_hwif_t *mate = hwif->mate;
-
+
pdc202xx_reset_host(hwif);
pdc202xx_reset_host(mate);
- pdc202xx_tune_drive(drive, 255);
+
+ ide_set_max_pio(drive);
}
static unsigned int __devinit init_chipset_pdc202xx(struct pci_dev *dev,
@@ -329,7 +329,9 @@ static void __devinit init_hwif_pdc202xx
hwif->rqsize = 256;
hwif->autodma = 0;
- hwif->tuneproc = &pdc202xx_tune_drive;
+
+ hwif->set_pio_mode = &pdc_set_pio_mode;
+
hwif->quirkproc = &pdc202xx_quirkproc;
if (hwif->pci_dev->device != PCI_DEVICE_ID_PROMISE_20246)
Index: b/drivers/ide/pci/piix.c
===================================================================
--- a/drivers/ide/pci/piix.c
+++ b/drivers/ide/pci/piix.c
@@ -17,11 +17,11 @@
* 41
* 43
*
- * | PIO 0 | c0 | 80 | 0 | piix_tune_drive(drive, 0);
- * | PIO 2 | SW2 | d0 | 90 | 4 | piix_tune_drive(drive, 2);
- * | PIO 3 | MW1 | e1 | a1 | 9 | piix_tune_drive(drive, 3);
- * | PIO 4 | MW2 | e3 | a3 | b | piix_tune_drive(drive, 4);
- *
+ * | PIO 0 | c0 | 80 | 0 |
+ * | PIO 2 | SW2 | d0 | 90 | 4 |
+ * | PIO 3 | MW1 | e1 | a1 | 9 |
+ * | PIO 4 | MW2 | e3 | a3 | b |
+ *
* sitre = word40 & 0x4000; primary
* sitre = word42 & 0x4000; secondary
*
@@ -210,16 +210,17 @@ static void piix_tune_pio (ide_drive_t *
}
/**
- * piix_tune_drive - tune a drive attached to PIIX
+ * piix_set_pio_mode - set PIO mode
+ *
* @drive: drive to tune
* @pio: desired PIO mode
*
* Set the drive's PIO mode (might be useful if drive is not registered
* in CMOS for any reason).
*/
-static void piix_tune_drive (ide_drive_t *drive, u8 pio)
+
+static void piix_set_pio_mode(ide_drive_t *drive, const u8 pio)
{
- pio = ide_get_best_pio_mode(drive, pio, 4);
piix_tune_pio(drive, pio);
(void) ide_config_drive_speed(drive, XFER_PIO_0 + pio);
}
@@ -319,7 +320,7 @@ static int piix_config_drive_xfer_rate (
return 0;
if (ide_use_fast_pio(drive))
- piix_tune_drive(drive, 255);
+ ide_set_max_pio(drive);
return -1;
}
@@ -456,7 +457,8 @@ static void __devinit init_hwif_piix(ide
}
hwif->autodma = 0;
- hwif->tuneproc = &piix_tune_drive;
+
+ hwif->set_pio_mode = &piix_set_pio_mode;
hwif->speedproc = &piix_tune_chipset;
hwif->drives[0].autotune = 1;
hwif->drives[1].autotune = 1;
Index: b/drivers/ide/pci/sc1200.c
===================================================================
--- a/drivers/ide/pci/sc1200.c
+++ b/drivers/ide/pci/sc1200.c
@@ -274,19 +274,20 @@ static int sc1200_ide_dma_end (ide_drive
}
/*
- * sc1200_tuneproc() handles selection/setting of PIO modes
+ * sc1200_set_pio_mode() handles setting of PIO modes
* for both the chipset and drive.
*
* All existing BIOSs for this chipset guarantee that all drives
* will have valid default PIO timings set up before we get here.
*/
-static void sc1200_tuneproc (ide_drive_t *drive, byte pio) /* mode=255 means "autotune" */
+
+static void sc1200_set_pio_mode(ide_drive_t *drive, const u8 pio)
{
ide_hwif_t *hwif = HWIF(drive);
int mode = -1;
/*
- * bad abuse of ->tuneproc interface
+ * bad abuse of ->set_pio_mode interface
*/
switch (pio) {
case 200: mode = XFER_UDMA_0; break;
@@ -304,9 +305,6 @@ static void sc1200_tuneproc (ide_drive_t
return;
}
- pio = ide_get_best_pio_mode(drive, pio, 4);
- printk("SC1200: %s: setting PIO mode%d\n", drive->name, pio);
-
if (sc1200_set_xfer_mode(drive, XFER_PIO_0 + pio) == 0)
sc1200_tunepio(drive, pio);
}
@@ -422,7 +420,8 @@ static void __devinit init_hwif_sc1200 (
hwif->ide_dma_end = &sc1200_ide_dma_end;
if (!noautodma)
hwif->autodma = 1;
- hwif->tuneproc = &sc1200_tuneproc;
+
+ hwif->set_pio_mode = &sc1200_set_pio_mode;
hwif->speedproc = &sc1200_tune_chipset;
}
hwif->atapi_dma = 1;
@@ -438,6 +437,7 @@ static ide_pci_device_t sc1200_chipset _
.init_hwif = init_hwif_sc1200,
.autodma = AUTODMA,
.bootable = ON_BOARD,
+ .host_flags = IDE_HFLAG_ABUSE_DMA_MODES,
.pio_mask = ATA_PIO4,
};
Index: b/drivers/ide/pci/scc_pata.c
===================================================================
--- a/drivers/ide/pci/scc_pata.c
+++ b/drivers/ide/pci/scc_pata.c
@@ -190,15 +190,16 @@ scc_ide_outsl(unsigned long port, void *
}
/**
- * scc_tuneproc - tune a drive PIO mode
+ * scc_set_pio_mode - tune a drive PIO mode
+ *
* @drive: drive to tune
- * @mode_wanted: the target operating mode
+ * @pio the target operating mode
*
* Load the timing settings for this device mode into the
* controller.
*/
-static void scc_tuneproc(ide_drive_t *drive, byte mode_wanted)
+static void scc_set_pio_mode(ide_drive_t *drive, const u8 pio)
{
ide_hwif_t *hwif = HWIF(drive);
struct scc_ports *ports = ide_get_hwifdata(hwif);
@@ -207,41 +208,22 @@ static void scc_tuneproc(ide_drive_t *dr
unsigned long piosht_port = ctl_base + 0x000;
unsigned long pioct_port = ctl_base + 0x004;
unsigned long reg;
- unsigned char speed = XFER_PIO_0;
int offset;
- mode_wanted = ide_get_best_pio_mode(drive, mode_wanted, 4);
- switch (mode_wanted) {
- case 4:
- speed = XFER_PIO_4;
- break;
- case 3:
- speed = XFER_PIO_3;
- break;
- case 2:
- speed = XFER_PIO_2;
- break;
- case 1:
- speed = XFER_PIO_1;
- break;
- case 0:
- default:
- speed = XFER_PIO_0;
- break;
- }
-
reg = in_be32((void __iomem *)cckctrl_port);
if (reg & CCKCTRL_ATACLKOEN) {
offset = 1; /* 133MHz */
} else {
offset = 0; /* 100MHz */
}
- reg = JCHSTtbl[offset][mode_wanted] << 16 | JCHHTtbl[offset][mode_wanted];
+
+ reg = JCHSTtbl[offset][pio] << 16 | JCHHTtbl[offset][pio];
out_be32((void __iomem *)piosht_port, reg);
- reg = JCHCTtbl[offset][mode_wanted];
+
+ reg = JCHCTtbl[offset][pio];
out_be32((void __iomem *)pioct_port, reg);
- ide_config_drive_speed(drive, speed);
+ ide_config_drive_speed(drive, XFER_PIO_0 + pio);
}
/**
@@ -338,7 +320,7 @@ static int scc_config_drive_for_dma(ide_
return 0;
if (ide_use_fast_pio(drive))
- scc_tuneproc(drive, 4);
+ scc_set_pio_mode(drive, 4); /* FIXME */
return -1;
}
@@ -699,7 +681,7 @@ static void __devinit init_hwif_scc(ide_
hwif->dma_setup = scc_dma_setup;
hwif->ide_dma_end = scc_ide_dma_end;
hwif->speedproc = scc_tune_chipset;
- hwif->tuneproc = scc_tuneproc;
+ hwif->set_pio_mode = scc_set_pio_mode;
hwif->ide_dma_check = scc_config_drive_for_dma;
hwif->ide_dma_test_irq = scc_dma_test_irq;
Index: b/drivers/ide/pci/serverworks.c
===================================================================
--- a/drivers/ide/pci/serverworks.c
+++ b/drivers/ide/pci/serverworks.c
@@ -207,9 +207,8 @@ static int svwks_tune_chipset (ide_drive
return (ide_config_drive_speed(drive, speed));
}
-static void svwks_tune_drive (ide_drive_t *drive, u8 pio)
+static void svwks_set_pio_mode(ide_drive_t *drive, const u8 pio)
{
- pio = ide_get_best_pio_mode(drive, pio, 4);
svwks_tune_pio(drive, pio);
(void)ide_config_drive_speed(drive, XFER_PIO_0 + pio);
}
@@ -222,7 +221,7 @@ static int svwks_config_drive_xfer_rate
return 0;
if (ide_use_fast_pio(drive))
- svwks_tune_drive(drive, 255);
+ ide_set_max_pio(drive);
return -1;
}
@@ -397,7 +396,7 @@ static void __devinit init_hwif_svwks (i
if (!hwif->irq)
hwif->irq = hwif->channel ? 15 : 14;
- hwif->tuneproc = &svwks_tune_drive;
+ hwif->set_pio_mode = &svwks_set_pio_mode;
hwif->speedproc = &svwks_tune_chipset;
hwif->udma_filter = &svwks_udma_filter;
Index: b/drivers/ide/pci/sgiioc4.c
===================================================================
--- a/drivers/ide/pci/sgiioc4.c
+++ b/drivers/ide/pci/sgiioc4.c
@@ -587,7 +587,7 @@ ide_init_sgiioc4(ide_hwif_t * hwif)
hwif->mwdma_mask = 0x2; /* Multimode-2 DMA */
hwif->swdma_mask = 0x2;
hwif->pio_mask = 0x00;
- hwif->tuneproc = NULL; /* Sets timing for PIO mode */
+ hwif->set_pio_mode = NULL; /* Sets timing for PIO mode */
hwif->speedproc = NULL; /* Sets timing for DMA &/or PIO modes */
hwif->selectproc = NULL;/* Use the default routine to select drive */
hwif->reset_poll = NULL;/* No HBA specific reset_poll needed */
Index: b/drivers/ide/pci/siimage.c
===================================================================
--- a/drivers/ide/pci/siimage.c
+++ b/drivers/ide/pci/siimage.c
@@ -219,9 +219,8 @@ static void sil_tune_pio(ide_drive_t *dr
}
}
-static void sil_tuneproc(ide_drive_t *drive, u8 pio)
+static void sil_set_pio_mode(ide_drive_t *drive, const u8 pio)
{
- pio = ide_get_best_pio_mode(drive, pio, 4);
sil_tune_pio(drive, pio);
(void)ide_config_drive_speed(drive, XFER_PIO_0 + pio);
}
@@ -331,7 +330,7 @@ static int siimage_config_drive_for_dma
return 0;
if (ide_use_fast_pio(drive))
- sil_tuneproc(drive, 255);
+ ide_set_max_pio(drive);
return -1;
}
@@ -902,7 +901,7 @@ static void __devinit init_hwif_siimage(
hwif->resetproc = &siimage_reset;
hwif->speedproc = &siimage_tune_chipset;
- hwif->tuneproc = &sil_tuneproc;
+ hwif->set_pio_mode = &sil_set_pio_mode;
hwif->reset_poll = &siimage_reset_poll;
hwif->pre_reset = &siimage_pre_reset;
hwif->udma_filter = &sil_udma_filter;
Index: b/drivers/ide/pci/sis5513.c
===================================================================
--- a/drivers/ide/pci/sis5513.c
+++ b/drivers/ide/pci/sis5513.c
@@ -519,14 +519,13 @@ static void config_art_rwp_pio (ide_driv
}
}
-static int sis5513_tune_drive(ide_drive_t *drive, u8 pio)
+static int sis5513_tune_drive(ide_drive_t *drive, const u8 pio)
{
- pio = ide_get_best_pio_mode(drive, pio, 4);
config_art_rwp_pio(drive, pio);
return ide_config_drive_speed(drive, XFER_PIO_0 + pio);
}
-static void sis5513_tuneproc(ide_drive_t *drive, u8 pio)
+static void sis_set_pio_mode(ide_drive_t *drive, const u8 pio)
{
(void)sis5513_tune_drive(drive, pio);
}
@@ -627,7 +626,7 @@ static int sis5513_config_xfer_rate(ide_
/*
* TODO: always set PIO mode and remove this
*/
- sis5513_tuneproc(drive, 255);
+ ide_set_max_pio(drive);
drive->init_speed = 0;
@@ -635,7 +634,7 @@ static int sis5513_config_xfer_rate(ide_
return 0;
if (ide_use_fast_pio(drive))
- sis5513_tuneproc(drive, 255);
+ ide_set_max_pio(drive);
return -1;
}
@@ -847,7 +846,7 @@ static void __devinit init_hwif_sis5513
if (!hwif->irq)
hwif->irq = hwif->channel ? 15 : 14;
- hwif->tuneproc = &sis5513_tuneproc;
+ hwif->set_pio_mode = &sis_set_pio_mode;
hwif->speedproc = &sis5513_tune_chipset;
if (!(hwif->dma_base)) {
Index: b/drivers/ide/pci/sl82c105.c
===================================================================
--- a/drivers/ide/pci/sl82c105.c
+++ b/drivers/ide/pci/sl82c105.c
@@ -75,16 +75,12 @@ static unsigned int get_pio_timings(ide_
/*
* Configure the chipset for PIO mode.
*/
-static u8 sl82c105_tune_pio(ide_drive_t *drive, u8 pio)
+static void sl82c105_tune_pio(ide_drive_t *drive, const u8 pio)
{
struct pci_dev *dev = HWIF(drive)->pci_dev;
int reg = 0x44 + drive->dn * 4;
u16 drv_ctrl;
- DBG(("sl82c105_tune_pio(drive:%s, pio:%u)\n", drive->name, pio));
-
- pio = ide_get_best_pio_mode(drive, pio, 5);
-
drv_ctrl = get_pio_timings(drive, pio);
/*
@@ -106,8 +102,6 @@ static u8 sl82c105_tune_pio(ide_drive_t
printk(KERN_DEBUG "%s: selected %s (%dns) (%04X)\n", drive->name,
ide_xfer_verbose(pio + XFER_PIO_0),
ide_pio_cycle_time(drive, pio), drv_ctrl);
-
- return pio;
}
/*
@@ -153,7 +147,7 @@ static int sl82c105_tune_chipset(ide_dri
case XFER_PIO_2:
case XFER_PIO_1:
case XFER_PIO_0:
- (void) sl82c105_tune_pio(drive, speed - XFER_PIO_0);
+ sl82c105_tune_pio(drive, speed - XFER_PIO_0);
break;
default:
return -1;
@@ -327,11 +321,10 @@ static void sl82c105_resetproc(ide_drive
* We only deal with PIO mode here - DMA mode 'using_dma' is not
* initialised at the point that this function is called.
*/
-static void sl82c105_tune_drive(ide_drive_t *drive, u8 pio)
+static void sl82c105_set_pio_mode(ide_drive_t *drive, const u8 pio)
{
- DBG(("sl82c105_tune_drive(drive:%s, pio:%u)\n", drive->name, pio));
+ sl82c105_tune_pio(drive, pio);
- pio = sl82c105_tune_pio(drive, pio);
(void) ide_config_drive_speed(drive, XFER_PIO_0 + pio);
}
@@ -401,7 +394,7 @@ static void __devinit init_hwif_sl82c105
DBG(("init_hwif_sl82c105(hwif: ide%d)\n", hwif->index));
- hwif->tuneproc = &sl82c105_tune_drive;
+ hwif->set_pio_mode = &sl82c105_set_pio_mode;
hwif->speedproc = &sl82c105_tune_chipset;
hwif->selectproc = &sl82c105_selectproc;
hwif->resetproc = &sl82c105_resetproc;
Index: b/drivers/ide/pci/slc90e66.c
===================================================================
--- a/drivers/ide/pci/slc90e66.c
+++ b/drivers/ide/pci/slc90e66.c
@@ -101,9 +101,8 @@ static void slc90e66_tune_pio (ide_drive
spin_unlock_irqrestore(&ide_lock, flags);
}
-static void slc90e66_tune_drive (ide_drive_t *drive, u8 pio)
+static void slc90e66_set_pio_mode(ide_drive_t *drive, const u8 pio)
{
- pio = ide_get_best_pio_mode(drive, pio, 4);
slc90e66_tune_pio(drive, pio);
(void) ide_config_drive_speed(drive, XFER_PIO_0 + pio);
}
@@ -168,7 +167,7 @@ static int slc90e66_config_drive_xfer_ra
return 0;
if (ide_use_fast_pio(drive))
- slc90e66_tune_drive(drive, 255);
+ ide_set_max_pio(drive);
return -1;
}
@@ -184,7 +183,7 @@ static void __devinit init_hwif_slc90e66
hwif->irq = hwif->channel ? 15 : 14;
hwif->speedproc = &slc90e66_tune_chipset;
- hwif->tuneproc = &slc90e66_tune_drive;
+ hwif->set_pio_mode = &slc90e66_set_pio_mode;
pci_read_config_byte(hwif->pci_dev, 0x47, ®47);
Index: b/drivers/ide/pci/tc86c001.c
===================================================================
--- a/drivers/ide/pci/tc86c001.c
+++ b/drivers/ide/pci/tc86c001.c
@@ -45,9 +45,8 @@ static int tc86c001_tune_chipset(ide_dri
return ide_config_drive_speed(drive, speed);
}
-static void tc86c001_tune_drive(ide_drive_t *drive, u8 pio)
+static void tc86c001_set_pio_mode(ide_drive_t *drive, const u8 pio)
{
- pio = ide_get_best_pio_mode(drive, pio, 4);
(void) tc86c001_tune_chipset(drive, XFER_PIO_0 + pio);
}
@@ -173,7 +172,7 @@ static int tc86c001_config_drive_xfer_ra
return 0;
if (ide_use_fast_pio(drive))
- tc86c001_tune_drive(drive, 255);
+ ide_set_max_pio(drive);
return -1;
}
@@ -195,7 +194,7 @@ static void __devinit init_hwif_tc86c001
/* Store the system control register base for convenience... */
hwif->config_data = sc_base;
- hwif->tuneproc = &tc86c001_tune_drive;
+ hwif->set_pio_mode = &tc86c001_set_pio_mode;
hwif->speedproc = &tc86c001_tune_chipset;
hwif->busproc = &tc86c001_busproc;
Index: b/drivers/ide/pci/triflex.c
===================================================================
--- a/drivers/ide/pci/triflex.c
+++ b/drivers/ide/pci/triflex.c
@@ -94,10 +94,9 @@ static int triflex_tune_chipset(ide_driv
return (ide_config_drive_speed(drive, speed));
}
-static void triflex_tune_drive(ide_drive_t *drive, u8 pio)
+static void triflex_set_pio_mode(ide_drive_t *drive, const u8 pio)
{
- int use_pio = ide_get_best_pio_mode(drive, pio, 4);
- (void) triflex_tune_chipset(drive, (XFER_PIO_0 + use_pio));
+ (void)triflex_tune_chipset(drive, XFER_PIO_0 + pio);
}
static int triflex_config_drive_xfer_rate(ide_drive_t *drive)
@@ -105,14 +104,14 @@ static int triflex_config_drive_xfer_rat
if (ide_tune_dma(drive))
return 0;
- triflex_tune_drive(drive, 255);
+ ide_set_max_pio(drive);
return -1;
}
static void __devinit init_hwif_triflex(ide_hwif_t *hwif)
{
- hwif->tuneproc = &triflex_tune_drive;
+ hwif->set_pio_mode = &triflex_set_pio_mode;
hwif->speedproc = &triflex_tune_chipset;
hwif->atapi_dma = 1;
Index: b/drivers/ide/pci/via82cxxx.c
===================================================================
--- a/drivers/ide/pci/via82cxxx.c
+++ b/drivers/ide/pci/via82cxxx.c
@@ -194,19 +194,17 @@ static int via_set_drive(ide_drive_t *dr
}
/**
- * via82cxxx_tune_drive - PIO setup
+ * via_set_pio_mode - PIO setup
+ *
* @drive: drive to set up
- * @pio: mode to use (255 for 'best possible')
+ * @pio: mode to use
*
* A callback from the upper layers for PIO-only tuning.
*/
-static void via82cxxx_tune_drive(ide_drive_t *drive, u8 pio)
+static void via_set_pio_mode(ide_drive_t *drive, const u8 pio)
{
- if (pio == 255)
- pio = ide_get_best_pio_mode(drive, 255, 5);
-
- via_set_drive(drive, XFER_PIO_0 + min_t(u8, pio, 5));
+ via_set_drive(drive, XFER_PIO_0 + pio);
}
/**
@@ -222,7 +220,7 @@ static int via82cxxx_ide_dma_check (ide_
u8 speed = ide_max_dma_mode(drive);
if (speed == 0) {
- via82cxxx_tune_drive(drive, 255);
+ ide_set_max_pio(drive);
return -1;
}
@@ -460,7 +458,7 @@ static void __devinit init_hwif_via82cxx
hwif->autodma = 0;
- hwif->tuneproc = &via82cxxx_tune_drive;
+ hwif->set_pio_mode = &via_set_pio_mode;
hwif->speedproc = &via_set_drive;
Index: b/drivers/ide/ppc/mpc8xx.c
===================================================================
--- a/drivers/ide/ppc/mpc8xx.c
+++ b/drivers/ide/ppc/mpc8xx.c
@@ -46,7 +46,7 @@ static void print_funcid (int func);
static int check_ide_device (unsigned long base);
static void ide_interrupt_ack (void *dev);
-static void m8xx_ide_tuneproc(ide_drive_t *drive, u8 pio);
+static void m8xx_ide_set_pio_mode(ide_drive_t *drive, const u8 pio);
typedef struct ide_ioport_desc {
unsigned long base_off; /* Offset to PCMCIA memory */
@@ -315,9 +315,8 @@ m8xx_ide_init_hwif_ports(hw_regs_t *hw,
#endif /* CONFIG_IDE_8xx_PCCARD */
}
- /* register routine to tune PIO mode */
ide_hwifs[data_port].pio_mask = ATA_PIO4;
- ide_hwifs[data_port].tuneproc = m8xx_ide_tuneproc;
+ ide_hwifs[data_port].set_pio_mode = m8xx_ide_set_pio_mode;
hw->ack_intr = (ide_ack_intr_t *) ide_interrupt_ack;
/* Enable Harddisk Interrupt,
@@ -402,9 +401,8 @@ void m8xx_ide_init_hwif_ports (hw_regs_t
*irq = ioport_dsc[data_port].irq;
}
- /* register routine to tune PIO mode */
ide_hwifs[data_port].pio_mask = ATA_PIO4;
- ide_hwifs[data_port].tuneproc = m8xx_ide_tuneproc;
+ ide_hwifs[data_port].set_pio_mode = m8xx_ide_set_pio_mode;
hw->ack_intr = (ide_ack_intr_t *) ide_interrupt_ack;
/* Enable Harddisk Interrupt,
@@ -428,24 +426,13 @@ void m8xx_ide_init_hwif_ports (hw_regs_t
#define PCMCIA_SL(t) ((t==32) ? 0 : ((t & 0x1F)<<7)) /* Strobe Length */
#endif
-
/* Calculate PIO timings */
-static void
-m8xx_ide_tuneproc(ide_drive_t *drive, u8 pio)
+static void m8xx_ide_set_pio_mode(ide_drive_t *drive, const u8 pio)
{
#if defined(CONFIG_IDE_8xx_PCCARD) || defined(CONFIG_IDE_8xx_DIRECT)
volatile pcmconf8xx_t *pcmp;
ulong timing, mask, reg;
-#endif
-
- pio = ide_get_best_pio_mode(drive, pio, 4);
-#if 1
- printk("%s[%d] %s: best PIO mode: %d\n",
- __FILE__,__LINE__,__FUNCTION__, pio);
-#endif
-
-#if defined(CONFIG_IDE_8xx_PCCARD) || defined(CONFIG_IDE_8xx_DIRECT)
pcmp = (pcmconf8xx_t *)(&(((immap_t *)IMAP_ADDR)->im_pcmcia));
mask = ~(PCMCIA_SHT(0xFF) | PCMCIA_SST(0xFF) | PCMCIA_SL(0xFF));
Index: b/drivers/ide/ppc/pmac.c
===================================================================
--- a/drivers/ide/ppc/pmac.c
+++ b/drivers/ide/ppc/pmac.c
@@ -412,7 +412,6 @@ kauai_lookup_timing(struct kauai_timing*
static void pmac_ide_setup_dma(pmac_ide_hwif_t *pmif, ide_hwif_t *hwif);
static int pmac_ide_build_dmatable(ide_drive_t *drive, struct request *rq);
static int pmac_ide_tune_chipset(ide_drive_t *drive, u8 speed);
-static void pmac_ide_tuneproc(ide_drive_t *drive, u8 pio);
static void pmac_ide_selectproc(ide_drive_t *drive);
static void pmac_ide_kauai_selectproc(ide_drive_t *drive);
@@ -613,7 +612,7 @@ out:
* Old tuning functions (called on hdparm -p), sets up drive PIO timings
*/
static void
-pmac_ide_tuneproc(ide_drive_t *drive, u8 pio)
+pmac_ide_set_pio_mode(ide_drive_t *drive, const u8 pio)
{
u32 *timings;
unsigned accessTicks, recTicks;
@@ -627,7 +626,6 @@ pmac_ide_tuneproc(ide_drive_t *drive, u8
/* which drive is it ? */
timings = &pmif->timings[drive->select.b.unit & 0x01];
- pio = ide_get_best_pio_mode(drive, pio, 4);
cycle_time = ide_pio_cycle_time(drive, pio);
switch (pmif->kind) {
@@ -973,7 +971,7 @@ pmac_ide_tune_chipset (ide_drive_t *driv
case XFER_PIO_2:
case XFER_PIO_1:
case XFER_PIO_0:
- pmac_ide_tuneproc(drive, speed & 0x07);
+ pmac_ide_set_pio_mode(drive, speed & 0x07);
break;
default:
ret = 1;
@@ -1249,7 +1247,7 @@ pmac_ide_setup_device(pmac_ide_hwif_t *p
hwif->drives[0].unmask = 1;
hwif->drives[1].unmask = 1;
hwif->pio_mask = ATA_PIO4;
- hwif->tuneproc = pmac_ide_tuneproc;
+ hwif->set_pio_mode = pmac_ide_set_pio_mode;
if (pmif->kind == controller_un_ata6
|| pmif->kind == controller_k2_ata6
|| pmif->kind == controller_sh_ata6)
Index: b/include/linux/ide.h
===================================================================
--- a/include/linux/ide.h
+++ b/include/linux/ide.h
@@ -634,7 +634,7 @@ typedef struct ide_drive_s {
unsigned int bios_cyl; /* BIOS/fdisk/LILO number of cyls */
unsigned int cyl; /* "real" number of cyls */
- unsigned int drive_data; /* use by tuneproc/selectproc */
+ unsigned int drive_data; /* use by set_pio_mode/selectproc */
unsigned int failures; /* current failure count */
unsigned int max_failures; /* maximum allowed failure count */
u64 probed_capacity;/* initial reported media capacity (ide-cd only currently) */
@@ -702,8 +702,8 @@ typedef struct hwif_s {
#if 0
ide_hwif_ops_t *hwifops;
#else
- /* routine to tune PIO mode for drives */
- void (*tuneproc)(ide_drive_t *, u8);
+ /* routine to set PIO mode for drives */
+ void (*set_pio_mode)(ide_drive_t *, const u8);
/* routine to retune DMA modes for drives */
int (*speedproc)(ide_drive_t *, u8);
/* tweaks hardware to select drive */
@@ -1255,6 +1255,12 @@ enum {
IDE_HFLAG_PIO_NO_BLACKLIST = (1 << 2),
/* don't use conservative PIO "downgrade" */
IDE_HFLAG_PIO_NO_DOWNGRADE = (1 << 3),
+ /* use PIO8/9 for prefetch off/on */
+ IDE_HFLAG_ABUSE_PREFETCH = (1 << 4),
+ /* use PIO6/7 for fast-devsel off/on */
+ IDE_HFLAG_ABUSE_FAST_DEVSEL = (1 << 5),
+ /* use 100-102 and 200-202 PIO values to set DMA modes */
+ IDE_HFLAG_ABUSE_DMA_MODES = (1 << 6),
};
typedef struct ide_pci_device_s {
@@ -1391,6 +1397,12 @@ unsigned int ide_pio_cycle_time(ide_driv
u8 ide_get_best_pio_mode(ide_drive_t *, u8, u8);
extern const ide_pio_timings_t ide_pio_timings[6];
+void ide_set_pio(ide_drive_t *, u8);
+
+static inline void ide_set_max_pio(ide_drive_t *drive)
+{
+ ide_set_pio(drive, 255);
+}
extern spinlock_t ide_lock;
extern struct mutex ide_cfg_mtx;
-
To unsubscribe from this list: send the line "unsubscribe linux-ide" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
