Simplify UltraDMA mode filtering in the driver:
- make use of the newly introduced 'udma_mask' field of 'ide_pci_device_t' to
set the correct hwif->ultra_mask, modifying init_setup_hpt366() to select
the correct mask based on the chip revision;
- replace 'max_mode' field of the 'struct hpt_info' with 'max_ultra' specifying
the maximum UltraDMA mode allowed;
- rewrite hpt3xx_udma_filter() to differ the filters based on the 'chip_type'
field, and only use it for HPT366 and HPT370[A] where it's really necessary.
Signed-off-by: Sergei Shtylyov <sshtylyov@xxxxxxxxxxxxx>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@xxxxxxxxx>
---
This patch is against the top of the pata-2.6. I had to change it a bit due to
a fixes going in ahead. Tested on HPT370, will try to test on HPT371N later...
drivers/ide/pci/hpt366.c | 150 +++++++++++++++++++++++++----------------------
1 files changed, 80 insertions(+), 70 deletions(-)
Index: linux-2.6/drivers/ide/pci/hpt366.c
===================================================================
--- linux-2.6.orig/drivers/ide/pci/hpt366.c
+++ linux-2.6/drivers/ide/pci/hpt366.c
@@ -1,5 +1,5 @@
/*
- * linux/drivers/ide/pci/hpt366.c Version 1.04 Jun 4, 2007
+ * linux/drivers/ide/pci/hpt366.c Version 1.10 Jun 6, 2007
*
* Copyright (C) 1999-2003 Andre Hedrick <andre@xxxxxxxxxxxxx>
* Portions Copyright (C) 2001 Sun Microsystems, Inc.
@@ -77,7 +77,7 @@
* since they may tamper with its fields
* - prefix the driver startup messages with the real chip name
* - claim the extra 240 bytes of I/O space for all chips
- * - optimize the rate masking/filtering and the drive list lookup code
+ * - optimize the UltraDMA filtering and the drive list lookup code
* - use pci_get_slot() to get to the function 1 of HPT36x/374
* - cache offset of the channel's misc. control registers (MCRs) being used
* throughout the driver
@@ -99,9 +99,9 @@
* stop duplicating it for each channel by storing the pointer in the pci_dev
* structure: first, at the init_setup stage, point it to a static "template"
* with only the chip type and its specific base DPLL frequency, the highest
- * supported DMA mode, and the chip settings table pointer filled, then, at
- * the init_chipset stage, allocate per-chip instance and fill it with the
- * rest of the necessary information
+ * UltraDMA mode, and the chip settings table pointer filled, then, at the
+ * init_chipset stage, allocate per-chip instance and fill it with the rest
+ * of the necessary information
* - get rid of the constant thresholds in the HPT37x PCI clock detection code,
* switch to calculating PCI clock frequency based on the chip's base DPLL
* frequency
@@ -112,6 +112,7 @@
* also fixing the interchanged 25/40 MHz PCI clock cases for HPT36x chips;
* unify HPT36x/37x timing setup code and the speedproc handlers by joining
* the register setting lists into the table indexed by the clock selected
+ * - set the correct hwif->ultra_mask for each individual chip
* Sergei Shtylyov, <sshtylyov@xxxxxxxxxxxxx> or <source@xxxxxxxxxx>
*/
@@ -390,7 +391,7 @@ enum ata_clock {
struct hpt_info {
u8 chip_type; /* Chip type */
- u8 max_mode; /* Speeds allowed */
+ u8 max_ultra; /* Max. UltraDMA mode allowed */
u8 dpll_clk; /* DPLL clock in MHz */
u8 pci_clk; /* PCI clock in MHz */
u32 **settings; /* Chipset settings table */
@@ -429,77 +430,77 @@ static u32 *hpt37x_settings[NUM_ATA_CLOC
static struct hpt_info hpt36x __devinitdata = {
.chip_type = HPT36x,
- .max_mode = (HPT366_ALLOW_ATA66_4 || HPT366_ALLOW_ATA66_3) ? 2 : 1,
+ .max_ultra = HPT366_ALLOW_ATA66_3 ? (HPT366_ALLOW_ATA66_4 ? 4 : 3) : 2,
.dpll_clk = 0, /* no DPLL */
.settings = hpt36x_settings
};
static struct hpt_info hpt370 __devinitdata = {
.chip_type = HPT370,
- .max_mode = HPT370_ALLOW_ATA100_5 ? 3 : 2,
+ .max_ultra = HPT370_ALLOW_ATA100_5 ? 5 : 4,
.dpll_clk = 48,
.settings = hpt37x_settings
};
static struct hpt_info hpt370a __devinitdata = {
.chip_type = HPT370A,
- .max_mode = HPT370_ALLOW_ATA100_5 ? 3 : 2,
+ .max_ultra = HPT370_ALLOW_ATA100_5 ? 5 : 4,
.dpll_clk = 48,
.settings = hpt37x_settings
};
static struct hpt_info hpt374 __devinitdata = {
.chip_type = HPT374,
- .max_mode = 3,
+ .max_ultra = 5,
.dpll_clk = 48,
.settings = hpt37x_settings
};
static struct hpt_info hpt372 __devinitdata = {
.chip_type = HPT372,
- .max_mode = HPT372_ALLOW_ATA133_6 ? 4 : 3,
+ .max_ultra = HPT372_ALLOW_ATA133_6 ? 6 : 5,
.dpll_clk = 55,
.settings = hpt37x_settings
};
static struct hpt_info hpt372a __devinitdata = {
.chip_type = HPT372A,
- .max_mode = HPT372_ALLOW_ATA133_6 ? 4 : 3,
+ .max_ultra = HPT372_ALLOW_ATA133_6 ? 6 : 5,
.dpll_clk = 66,
.settings = hpt37x_settings
};
static struct hpt_info hpt302 __devinitdata = {
.chip_type = HPT302,
- .max_mode = HPT302_ALLOW_ATA133_6 ? 4 : 3,
+ .max_ultra = HPT372_ALLOW_ATA133_6 ? 6 : 5,
.dpll_clk = 66,
.settings = hpt37x_settings
};
static struct hpt_info hpt371 __devinitdata = {
.chip_type = HPT371,
- .max_mode = HPT371_ALLOW_ATA133_6 ? 4 : 3,
+ .max_ultra = HPT371_ALLOW_ATA133_6 ? 6 : 5,
.dpll_clk = 66,
.settings = hpt37x_settings
};
static struct hpt_info hpt372n __devinitdata = {
.chip_type = HPT372N,
- .max_mode = HPT372_ALLOW_ATA133_6 ? 4 : 3,
+ .max_ultra = HPT372_ALLOW_ATA133_6 ? 6 : 5,
.dpll_clk = 77,
.settings = hpt37x_settings
};
static struct hpt_info hpt302n __devinitdata = {
.chip_type = HPT302N,
- .max_mode = HPT302_ALLOW_ATA133_6 ? 4 : 3,
+ .max_ultra = HPT302_ALLOW_ATA133_6 ? 6 : 5,
.dpll_clk = 77,
.settings = hpt37x_settings
};
static struct hpt_info hpt371n __devinitdata = {
.chip_type = HPT371N,
- .max_mode = HPT371_ALLOW_ATA133_6 ? 4 : 3,
+ .max_ultra = HPT371_ALLOW_ATA133_6 ? 6 : 5,
.dpll_clk = 77,
.settings = hpt37x_settings
};
@@ -522,53 +523,38 @@ static int check_in_drive_list(ide_drive
static u8 hpt3xx_udma_filter(ide_drive_t *drive)
{
struct hpt_info *info = pci_get_drvdata(HWIF(drive)->pci_dev);
- u8 chip_type = info->chip_type;
- u8 mode = info->max_mode;
u8 mask;
- switch (mode) {
- case 0x04:
- mask = 0x7f;
- break;
- case 0x03:
+ switch (info->chip_type) {
+ case HPT370A:
+ if (!HPT370_ALLOW_ATA100_5 ||
+ check_in_drive_list(drive, bad_ata100_5))
+ return 0x1f;
+ else
+ return 0x3f;
+ case HPT370:
+ if (!HPT370_ALLOW_ATA100_5 ||
+ check_in_drive_list(drive, bad_ata100_5))
+ mask = 0x1f;
+ else
mask = 0x3f;
- if (chip_type >= HPT374)
- break;
- if (!check_in_drive_list(drive, bad_ata100_5))
- goto check_bad_ata33;
- /* fall thru */
- case 0x02:
+ break;
+ case HPT36x:
+ if (!HPT366_ALLOW_ATA66_4 ||
+ check_in_drive_list(drive, bad_ata66_4))
+ mask = 0x0f;
+ else
mask = 0x1f;
- /*
- * CHECK ME, Does this need to be changed to HPT374 ??
- */
- if (chip_type >= HPT370)
- goto check_bad_ata33;
- if (HPT366_ALLOW_ATA66_4 &&
- !check_in_drive_list(drive, bad_ata66_4))
- goto check_bad_ata33;
-
- mask = 0x0f;
- if (HPT366_ALLOW_ATA66_3 &&
- !check_in_drive_list(drive, bad_ata66_3))
- goto check_bad_ata33;
- /* fall thru */
- case 0x01:
+ if (!HPT366_ALLOW_ATA66_3 ||
+ check_in_drive_list(drive, bad_ata66_3))
mask = 0x07;
-
- check_bad_ata33:
- if (chip_type >= HPT370A)
- break;
- if (!check_in_drive_list(drive, bad_ata33))
- break;
- /* fall thru */
- case 0x00:
- default:
- mask = 0x00;
- break;
+ break;
+ default:
+ return 0x7f;
}
- return mask;
+
+ return check_in_drive_list(drive, bad_ata33) ? 0x00 : mask;
}
static u32 get_speed_setting(u8 speed, struct hpt_info *info)
@@ -1149,7 +1135,7 @@ static unsigned int __devinit init_chips
* Select 66 MHz DPLL clock only if UltraATA/133 mode is
* supported/enabled, use 50 MHz DPLL clock otherwise...
*/
- if (info->max_mode == 0x04) {
+ if (info->max_ultra == 6) {
dpll_clk = 66;
clock = ATA_CLOCK_66MHZ;
} else if (dpll_clk) { /* HPT36x chips don't have DPLL */
@@ -1242,7 +1228,7 @@ static void __devinit init_hwif_hpt366(i
struct pci_dev *dev = hwif->pci_dev;
struct hpt_info *info = pci_get_drvdata(dev);
int serialize = HPT_SERIALIZE_IO;
- u8 scr1 = 0, ata66 = (hwif->channel) ? 0x01 : 0x02;
+ u8 scr1 = 0, ata66 = hwif->channel ? 0x01 : 0x02;
u8 chip_type = info->chip_type;
u8 new_mcr, old_mcr = 0;
@@ -1255,7 +1241,9 @@ static void __devinit init_hwif_hpt366(i
hwif->intrproc = &hpt3xx_intrproc;
hwif->maskproc = &hpt3xx_maskproc;
hwif->busproc = &hpt3xx_busproc;
- hwif->udma_filter = &hpt3xx_udma_filter;
+
+ if (chip_type <= HPT370A)
+ hwif->udma_filter = &hpt3xx_udma_filter;
/*
* HPT3xxN chips have some complications:
@@ -1304,7 +1292,7 @@ static void __devinit init_hwif_hpt366(i
return;
}
- hwif->ultra_mask = 0x7f;
+ hwif->ultra_mask = hwif->cds->udma_mask;
hwif->mwdma_mask = 0x07;
/*
@@ -1502,9 +1490,33 @@ static int __devinit init_setup_hpt366(s
pci_read_config_byte(dev, PCI_REVISION_ID, &rev);
- if (rev > 6)
+ switch (rev) {
+ case 0:
+ case 1:
+ case 2:
+ /*
+ * HPT36x chips are single channel and
+ * do not seem to have the channel enable bit...
+ */
+ d->channels = 1;
+ d->enablebits[0].reg = 0;
+
+ d->udma_mask = HPT366_ALLOW_ATA66_3 ?
+ (HPT366_ALLOW_ATA66_4 ? 0x1f : 0x0f) : 0x07;
+ break;
+ case 3:
+ case 4:
+ d->udma_mask = HPT370_ALLOW_ATA100_5 ? 0x3f : 0x1f;
+ break;
+ default:
rev = 6;
-
+ /* fall thru */
+ case 5:
+ case 6:
+ d->udma_mask = HPT372_ALLOW_ATA133_6 ? 0x7f : 0x3f;
+ break;
+ }
+
d->name = chipset_names[rev];
pci_set_drvdata(dev, info[rev]);
@@ -1512,13 +1524,6 @@ static int __devinit init_setup_hpt366(s
if (rev > 2)
goto init_single;
- /*
- * HPT36x chips are single channel and
- * do not seem to have the channel enable bit...
- */
- d->channels = 1;
- d->enablebits[0].reg = 0;
-
if ((dev2 = pci_get_slot(dev->bus, dev->devfn + 1)) != NULL) {
u8 pin1 = 0, pin2 = 0;
int ret;
@@ -1562,6 +1567,7 @@ static ide_pci_device_t hpt366_chipsets[
.channels = 2,
.autodma = AUTODMA,
.enablebits = {{0x50,0x04,0x04}, {0x54,0x04,0x04}},
+ .udma_mask = HPT372_ALLOW_ATA133_6 ? 0x7f : 0x3f,
.bootable = OFF_BOARD,
.extra = 240
},{ /* 2 */
@@ -1573,6 +1579,7 @@ static ide_pci_device_t hpt366_chipsets[
.channels = 2,
.autodma = AUTODMA,
.enablebits = {{0x50,0x04,0x04}, {0x54,0x04,0x04}},
+ .udma_mask = HPT302_ALLOW_ATA133_6 ? 0x7f : 0x3f,
.bootable = OFF_BOARD,
.extra = 240
},{ /* 3 */
@@ -1584,6 +1591,7 @@ static ide_pci_device_t hpt366_chipsets[
.channels = 2,
.autodma = AUTODMA,
.enablebits = {{0x50,0x04,0x04}, {0x54,0x04,0x04}},
+ .udma_mask = HPT371_ALLOW_ATA133_6 ? 0x7f : 0x3f,
.bootable = OFF_BOARD,
.extra = 240
},{ /* 4 */
@@ -1595,6 +1603,7 @@ static ide_pci_device_t hpt366_chipsets[
.channels = 2, /* 4 */
.autodma = AUTODMA,
.enablebits = {{0x50,0x04,0x04}, {0x54,0x04,0x04}},
+ .udma_mask = 0x3f,
.bootable = OFF_BOARD,
.extra = 240
},{ /* 5 */
@@ -1606,6 +1615,7 @@ static ide_pci_device_t hpt366_chipsets[
.channels = 2, /* 4 */
.autodma = AUTODMA,
.enablebits = {{0x50,0x04,0x04}, {0x54,0x04,0x04}},
+ .udma_mask = HPT372_ALLOW_ATA133_6 ? 0x7f : 0x3f,
.bootable = OFF_BOARD,
.extra = 240
}
-
To unsubscribe from this list: send the line "unsubscribe linux-ide" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
