Implement ahci_[de]init_port() and use it during initialization and
de-initialization. ahci_[de]init_port() are supersets of what used to
be done during driver [de-]initialization. This patch makes the
following behavior changes.
* Per-port IRQ mask is cleared on driver load as done in other
drivers. The mask will be configured properly during probe.
* During init_one(), HOST_IRQ_STAT is cleared after masking port IRQs
such that there is no race window.
* CMD_SPIN_UP is cleared during init_one() instead of being set. It
is set in port_start(). This is more consistent with overall
structure of initialization. Note that CMD_SPIN_UP simply controls
PHY activation.
* Slumber and staggered spin-up are handled properly.
* All init/deinit operations are done in step-by-step manner as
described in the spec instead of issued as single merged command.
Original implementation is from Zhao, Forrest <forrest.zhao@xxxxxxxxx>
Signed-off-by: Tejun Heo <htejun@xxxxxxxxx>
Signed-off-by: Zhao, Forrest <forrest.zhao@xxxxxxxxx>
---
drivers/scsi/ahci.c | 202 ++++++++++++++++++++++++++++++++++++++-------------
1 files changed, 151 insertions(+), 51 deletions(-)
d773d83a6f3c558226b24a09131b0afa83e0ac02
diff --git a/drivers/scsi/ahci.c b/drivers/scsi/ahci.c
index e02b9c6..fb71fa7 100644
--- a/drivers/scsi/ahci.c
+++ b/drivers/scsi/ahci.c
@@ -92,7 +92,9 @@ enum {
HOST_AHCI_EN = (1 << 31), /* AHCI enabled */
/* HOST_CAP bits */
+ HOST_CAP_SSC = (1 << 14), /* Slumber capable */
HOST_CAP_CLO = (1 << 24), /* Command List Override support */
+ HOST_CAP_SSS = (1 << 27), /* Staggered Spin-up */
HOST_CAP_NCQ = (1 << 30), /* Native Command Queueing */
HOST_CAP_64 = (1 << 31), /* PCI DAC (64-bit DMA) support */
@@ -155,6 +157,7 @@ enum {
PORT_CMD_SPIN_UP = (1 << 1), /* Spin up device */
PORT_CMD_START = (1 << 0), /* Enable port DMA engine */
+ PORT_CMD_ICC_MASK = (0xf << 28), /* i/f ICC state mask */
PORT_CMD_ICC_ACTIVE = (0x1 << 28), /* Put i/f in active state */
PORT_CMD_ICC_PARTIAL = (0x2 << 28), /* Put i/f in partial state */
PORT_CMD_ICC_SLUMBER = (0x6 << 28), /* Put i/f in slumber state */
@@ -440,6 +443,135 @@ static int ahci_stop_engine(void __iomem
return 0;
}
+static void ahci_start_fis_rx(void __iomem *port_mmio, u32 cap,
+ dma_addr_t cmd_slot_dma, dma_addr_t rx_fis_dma)
+{
+ u32 tmp;
+
+ /* set FIS registers */
+ if (cap & HOST_CAP_64)
+ writel((cmd_slot_dma >> 16) >> 16, port_mmio + PORT_LST_ADDR_HI);
+ writel(cmd_slot_dma & 0xffffffff, port_mmio + PORT_LST_ADDR);
+
+ if (cap & HOST_CAP_64)
+ writel((rx_fis_dma >> 16) >> 16, port_mmio + PORT_FIS_ADDR_HI);
+ writel(rx_fis_dma & 0xffffffff, port_mmio + PORT_FIS_ADDR);
+
+ /* enable FIS reception */
+ tmp = readl(port_mmio + PORT_CMD);
+ tmp |= PORT_CMD_FIS_RX;
+ writel(tmp, port_mmio + PORT_CMD);
+
+ /* flush */
+ readl(port_mmio + PORT_CMD);
+}
+
+static int ahci_stop_fis_rx(void __iomem *port_mmio)
+{
+ u32 tmp;
+
+ /* disable FIS reception */
+ tmp = readl(port_mmio + PORT_CMD);
+ tmp &= ~PORT_CMD_FIS_RX;
+ writel(tmp, port_mmio + PORT_CMD);
+
+ /* wait for completion, spec says 500ms, give it 1000 */
+ tmp = ata_wait_register(port_mmio + PORT_CMD, PORT_CMD_FIS_ON,
+ PORT_CMD_FIS_ON, 10, 1000);
+ if (tmp & PORT_CMD_FIS_ON)
+ return -EBUSY;
+
+ return 0;
+}
+
+static void ahci_power_up(void __iomem *port_mmio, u32 cap)
+{
+ u32 cmd;
+
+ cmd = readl(port_mmio + PORT_CMD) & ~PORT_CMD_ICC_MASK;
+
+ /* spin up device */
+ if (cap & HOST_CAP_SSS) {
+ cmd |= PORT_CMD_SPIN_UP;
+ writel(cmd, port_mmio + PORT_CMD);
+ }
+
+ /* wake up link */
+ writel(cmd | PORT_CMD_ICC_ACTIVE, port_mmio + PORT_CMD);
+}
+
+static void ahci_power_down(void __iomem *port_mmio, u32 cap)
+{
+ u32 cmd, scontrol;
+
+ cmd = readl(port_mmio + PORT_CMD) & ~PORT_CMD_ICC_MASK;
+
+ if (cap & HOST_CAP_SSC) {
+ /* enable transitions to slumber mode */
+ scontrol = readl(port_mmio + PORT_SCR_CTL);
+ if ((scontrol & 0x0f00) > 0x100) {
+ scontrol &= ~0xf00;
+ writel(scontrol, port_mmio + PORT_SCR_CTL);
+ }
+
+ /* put device into slumber mode */
+ writel(cmd | PORT_CMD_ICC_SLUMBER, port_mmio + PORT_CMD);
+
+ /* wait for the transition to complete */
+ ata_wait_register(port_mmio + PORT_CMD, PORT_CMD_ICC_SLUMBER,
+ PORT_CMD_ICC_SLUMBER, 1, 50);
+ }
+
+ /* put device into listen mode */
+ if (cap & HOST_CAP_SSS) {
+ /* first set PxSCTL.DET to 0 */
+ scontrol = readl(port_mmio + PORT_SCR_CTL);
+ scontrol &= ~0xf;
+ writel(scontrol, port_mmio + PORT_SCR_CTL);
+
+ /* then set PxCMD.SUD to 0 */
+ cmd &= ~PORT_CMD_SPIN_UP;
+ writel(cmd, port_mmio + PORT_CMD);
+ }
+}
+
+static void ahci_init_port(void __iomem *port_mmio, u32 cap,
+ dma_addr_t cmd_slot_dma, dma_addr_t rx_fis_dma)
+{
+ /* power up */
+ ahci_power_up(port_mmio, cap);
+
+ /* enable FIS reception */
+ ahci_start_fis_rx(port_mmio, cap, cmd_slot_dma, rx_fis_dma);
+
+ /* enable DMA */
+ ahci_start_engine(port_mmio);
+}
+
+static int ahci_deinit_port(void __iomem *port_mmio, u32 cap, const char **emsg)
+{
+ int rc;
+
+ /* disable DMA */
+ rc = ahci_stop_engine(port_mmio);
+ if (rc) {
+ *emsg = "failed to stop engine";
+ return rc;
+ }
+
+ /* disable FIS reception */
+ rc = ahci_stop_fis_rx(port_mmio);
+ if (rc) {
+ *emsg = "failed stop FIS RX";
+ return rc;
+ }
+
+ /* put device into slumber mode */
+ ahci_power_down(port_mmio, cap);
+
+ return 0;
+}
+
static unsigned int ahci_dev_classify(struct ata_port *ap)
{
void __iomem *port_mmio = (void __iomem *) ap->ioaddr.cmd_addr;
@@ -1037,20 +1169,8 @@ static int ahci_port_start(struct ata_po
ap->private_data = pp;
- if (hpriv->cap & HOST_CAP_64)
- writel((pp->cmd_slot_dma >> 16) >> 16, port_mmio + PORT_LST_ADDR_HI);
- writel(pp->cmd_slot_dma & 0xffffffff, port_mmio + PORT_LST_ADDR);
- readl(port_mmio + PORT_LST_ADDR); /* flush */
-
- if (hpriv->cap & HOST_CAP_64)
- writel((pp->rx_fis_dma >> 16) >> 16, port_mmio + PORT_FIS_ADDR_HI);
- writel(pp->rx_fis_dma & 0xffffffff, port_mmio + PORT_FIS_ADDR);
- readl(port_mmio + PORT_FIS_ADDR); /* flush */
-
- writel(PORT_CMD_ICC_ACTIVE | PORT_CMD_FIS_RX |
- PORT_CMD_POWER_ON | PORT_CMD_SPIN_UP |
- PORT_CMD_START, port_mmio + PORT_CMD);
- readl(port_mmio + PORT_CMD); /* flush */
+ /* initialize port */
+ ahci_init_port(port_mmio, hpriv->cap, pp->cmd_slot_dma, pp->rx_fis_dma);
return 0;
}
@@ -1058,20 +1178,17 @@ static int ahci_port_start(struct ata_po
static void ahci_port_stop(struct ata_port *ap)
{
struct device *dev = ap->host_set->dev;
+ struct ahci_host_priv *hpriv = ap->host_set->private_data;
struct ahci_port_priv *pp = ap->private_data;
void __iomem *mmio = ap->host_set->mmio_base;
void __iomem *port_mmio = ahci_port_base(mmio, ap->port_no);
- u32 tmp;
-
- tmp = readl(port_mmio + PORT_CMD);
- tmp &= ~(PORT_CMD_START | PORT_CMD_FIS_RX);
- writel(tmp, port_mmio + PORT_CMD);
- readl(port_mmio + PORT_CMD); /* flush */
+ const char *emsg = NULL;
+ int rc;
- /* spec says 500 msecs for each PORT_CMD_{START,FIS_RX} bit, so
- * this is slightly incorrect.
- */
- msleep(500);
+ /* de-initialize port */
+ rc = ahci_deinit_port(port_mmio, hpriv->cap, &emsg);
+ if (rc)
+ ata_port_printk(ap, KERN_WARNING, "%s (%d)\n", emsg, rc);
ap->private_data = NULL;
dma_free_coherent(dev, AHCI_PORT_PRIV_DMA_SZ,
@@ -1099,7 +1216,7 @@ static int ahci_host_init(struct ata_pro
struct pci_dev *pdev = to_pci_dev(probe_ent->dev);
void __iomem *mmio = probe_ent->mmio_base;
u32 tmp, cap_save;
- unsigned int i, j, using_dac;
+ unsigned int i, using_dac;
int rc;
void __iomem *port_mmio;
@@ -1175,6 +1292,8 @@ static int ahci_host_init(struct ata_pro
}
for (i = 0; i < probe_ent->n_ports; i++) {
+ const char *emsg = NULL;
+
#if 0 /* BIOSen initialize this incorrectly */
if (!(hpriv->port_map & (1 << i)))
continue;
@@ -1187,43 +1306,24 @@ #endif
(unsigned long) mmio, i);
/* make sure port is not active */
- tmp = readl(port_mmio + PORT_CMD);
- VPRINTK("PORT_CMD 0x%x\n", tmp);
- if (tmp & (PORT_CMD_LIST_ON | PORT_CMD_FIS_ON |
- PORT_CMD_FIS_RX | PORT_CMD_START)) {
- tmp &= ~(PORT_CMD_LIST_ON | PORT_CMD_FIS_ON |
- PORT_CMD_FIS_RX | PORT_CMD_START);
- writel(tmp, port_mmio + PORT_CMD);
- readl(port_mmio + PORT_CMD); /* flush */
-
- /* spec says 500 msecs for each bit, so
- * this is slightly incorrect.
- */
- msleep(500);
- }
-
- writel(PORT_CMD_SPIN_UP, port_mmio + PORT_CMD);
-
- j = 0;
- while (j < 100) {
- msleep(10);
- tmp = readl(port_mmio + PORT_SCR_STAT);
- if ((tmp & 0xf) == 0x3)
- break;
- j++;
- }
+ rc = ahci_deinit_port(port_mmio, hpriv->cap, &emsg);
+ if (rc)
+ dev_printk(KERN_WARNING, &pdev->dev,
+ "%s (%d)\n", emsg, rc);
+ /* clear SError */
tmp = readl(port_mmio + PORT_SCR_ERR);
VPRINTK("PORT_SCR_ERR 0x%x\n", tmp);
writel(tmp, port_mmio + PORT_SCR_ERR);
- /* ack any pending irq events for this port */
+ /* clear & turn off port IRQ */
tmp = readl(port_mmio + PORT_IRQ_STAT);
VPRINTK("PORT_IRQ_STAT 0x%x\n", tmp);
if (tmp)
writel(tmp, port_mmio + PORT_IRQ_STAT);
writel(1 << i, mmio + HOST_IRQ_STAT);
+ writel(0, port_mmio + PORT_IRQ_MASK);
}
tmp = readl(mmio + HOST_CTL);
--
1.3.2
-
: send the line "unsubscribe linux-ide" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
