----- Original Message ----- From: "Michael S. Tsirkin" <mst@xxxxxxxxxxxxxx>
To: "Roland Dreier" <rdreier@xxxxxxxxx>Cc: <linux-kernel@xxxxxxxxxxxxxxx>; <linux-ia64@xxxxxxxxxxxxxxx>; <jeff@xxxxxxxxxx>; <matthew@xxxxxx>; <openib-general@xxxxxxxxxx>; <linux-pci@xxxxxxxxxxxxxxxxxxxxxxxx>; "David Miller" <davem@xxxxxxxxxxxxx>
Sent: Tuesday, October 31, 2006 2:53 PM Subject: Re: Ordering between PCI config space writes and MMIO reads?
Quoting r. Roland Dreier <rdreier@xxxxxxxxx>:Subject: Re: Ordering between PCI config space writes and MMIO reads? The discussion fizzled out without really reaching a definitive answer, so I'm going to apply the original patch (below), since I pretty much convinced myself that only the driver doing the config access has enough information to fix this reliably. - R. Author: John Partridge <johnip@xxxxxxx> Date: Tue Oct 31 11:00:04 2006 -0800IB/mthca: Make sure all PCI config writes reach device before doing MMIODuring initialization, mthca writes some PCI config space registersand then does an MMIO read from one of the BARs it just enabled. ThisMMIO read sometimes failed and caused a crash on SGI Altix machines, because the PCI-X host bridge (legitimately, according to the PCIspec) allowed the MMIO read to start before the config write completed.To fix this, add a config read after all config writes to make sure they are all done before starting the MMIO read. Signed-off-by: John Partridge <johnip@xxxxxxx> Signed-off-by: Roland Dreier <rolandd@xxxxxxxxx>diff --git a/drivers/infiniband/hw/mthca/mthca_reset.c b/drivers/infiniband/hw/mthca/mthca_reset.cindex 91934f2..578dc7c 100644 --- a/drivers/infiniband/hw/mthca/mthca_reset.c +++ b/drivers/infiniband/hw/mthca/mthca_reset.c @@ -281,6 +281,20 @@ good: goto out; } + /* + * Perform a "flush" of the PCI config writes here by reading + * the PCI_COMMAND register. This is needed to make sure that + * we don't try to touch other PCI BARs before the config + * writes are done -- otherwise an MMIO cycle could start + * before the config writes are done and reach the HCA before + * the BAR is actually enabled. + */ + if (pci_read_config_dword(mdev->pdev, PCI_COMMAND, hca_header)) { + err = -ENODEV; + mthca_err(mdev, "Couldn't access HCA memory after restoring, " + "aborting.\n"); + } + out: if (bridge) pci_dev_put(bridge);Here's what I don't understand: according to PCI rules, pci config read can bypass pci config write (both are non-posted). So why does doing it help flush the writes as the comment claims? Isn't this more the case of /* pci_config_write seems to complete asynchronously on Altix systems. * This is probably broken but its not clear what's the best * thing to do is - for now, do pci_read_config_dword which seems to flush * everything out. */
If you write to the PCI bus and then you read the result, the read __might__ be the read that flushes any posted writes rather than the read of device registers that
would occur after the BARs were configured (hardware may be slower thanthe CPU). So, it's best to do the required configuration cycles first, then after all is done, read something before you actually need to use data from subsequent
read/write cycles.
-- MST - To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html Please read the FAQ at http://www.tux.org/lkml/
Cheers, Dick Johnson Penguin : Linux version 2.6.16.24 (somewhere) New Book: http://www.AbominableFirebug.com - To unsubscribe from this list: send the line "unsubscribe linux-ia64" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
![]() |