....JW----- Original Message ----- From: "Roland Dreier" <rdreier@xxxxxxxxx>
To: <linux-pci@xxxxxxxxxxxxxxxxxxxxxxxx>; <linux-ia64@xxxxxxxxxxxxxxx> Cc: <linux-kernel@xxxxxxxxxxxxxxx>; <openib-general@xxxxxxxxxx> Sent: Tuesday, October 24, 2006 2:13 PMSubject: [openib-general] Ordering between PCI config space writes and MMIO reads?
John Partridge found an interesting bug involving mthca (Mellanox InfiniBand HCA driver) on IA64/Altix systems. Basically, during initialization, mthca does: - do some config writes, including enabling BARs - then start a firmware command - read an MMIO register from a BAR (to check if FW is busy) However, John found that the Altix PCI-X bridge was allowing the MMIO read to start before the config write was done (which is allowed by the PCI spec). The PCI trace looked like:23454: Config Write REG = 01 TYPE = 1 BE = 0000 Req = (0,0,0) Tag = 1 Bus = 1 Device = 0 Function = 0 WAIT = 2 23462: Memory Rd DW A = 00280698 BE = 0000 Req = (0,0,0) Tag = 0 WAIT = 2 23470: Split compl. Lower A = 00 Req = (0,0,0) Tag = 0 Comp = (0,2,0) WAIT = 1 (Error completion) 23476: Split compl. Lower A = 00 Req = (0,0,0) Tag = 1 Comp = (0,2,0) WAIT = 1 (Normal completion of WRITE)and that "Error completion" leads to a crash. John proposed the following patch to fix this, which looks good to me. However, I have a couple of questions about this situation: 1) Is this something that should be fixed in the driver? The PCI spec allows MMIO cycles to start before an earlier config cycle completed, but do we want to expose this fact to drivers? Would it be better for ia64 to use some sort of barrier to make sure pci_write_config_xxx() is strongly ordered with MMIO? 2) Is this issue lurking in other drivers? Thanks, Roland commit 424b50b6360b325ce642ece687756a600c25d28a Author: John Partridge <johnip@xxxxxxx> Date: Tue Oct 24 11:54:16 2006 -0700IB/mthca: Make sure all PCI config writes reach device before doing MMIODuring initialization, mthca writes some PCI config space registers and then does an MMIO read from one of the BARs it just enabled. This MMIO read sometimes failed and caused a crash on SGI Altix machines, because the PCI-X host bridge (legitimately, according to the PCI spec) allowed the MMIO read to start before the config write completed. To fix this, add a config read after all config writes to make sure they are all done before starting the MMIO read. Signed-off-by: John Partridge <johnip@xxxxxxx> Signed-off-by: Roland Dreier <rolandd@xxxxxxxxx>diff --git a/drivers/infiniband/hw/mthca/mthca_reset.c b/drivers/infiniband/hw/mthca/mthca_reset.cindex 91934f2..578dc7c 100644 --- a/drivers/infiniband/hw/mthca/mthca_reset.c +++ b/drivers/infiniband/hw/mthca/mthca_reset.c @@ -281,6 +281,20 @@ good: goto out; } + /* + * Perform a "flush" of the PCI config writes here by reading + * the PCI_COMMAND register. This is needed to make sure that + * we don't try to touch other PCI BARs before the config + * writes are done -- otherwise an MMIO cycle could start + * before the config writes are done and reach the HCA before + * the BAR is actually enabled. + */ + if (pci_read_config_dword(mdev->pdev, PCI_COMMAND, hca_header)) { + err = -ENODEV; + mthca_err(mdev, "Couldn't access HCA memory after restoring, " + "aborting.\n"); + } + out: if (bridge) pci_dev_put(bridge); _______________________________________________ openib-general mailing list openib-general@xxxxxxxxxx http://openib.org/mailman/listinfo/openib-generalTo unsubscribe, please visit http://openib.org/mailman/listinfo/openib-general
- To unsubscribe from this list: send the line "unsubscribe linux-ia64" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
![]() |