Re: [PATCH v2 2/2] i2c: dwsignware: determine HS tHIGH and tLOW based on HW parameters

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Fri, Sep 27, 2024 at 12:22:17PM +0800, Michael Wu wrote:
> In commit 35eba185fd1a ("i2c: designware: Calculate SCL timing parameter
> for High Speed Mode") hs_hcnt and hs_lcnt are calculated based on fixed
> tHIGH = 160 and tLOW = 120. However, the set of these fixed values only
> applies to the combination of hardware parameters IC_CAP_LOADING = 400pF
> and IC_CLK_FREQ_OPTIMIZATION = 1. Outside of this combination, if these
> fixed tHIGH = 160 and tLOW = 120 are still used, the calculated hs_hcnt
> and hs_lcnt may not be small enough, making it impossible for the SCL
> frequency to reach 3.4 MHz.
> 
> Section 3.15.4.5 in DesignWare DW_apb_i2b Databook v2.03 says that when
> IC_CLK_FREQ_OPTIMIZATION = 0,
> 
>     MIN_SCL_HIGHtime = 60 ns for 3.4 Mbps, bus loading = 100pF
> 		     = 120 ns for 3.4 Mbps, bus loading = 400pF
>     MIN_SCL_LOWtime = 160 ns for 3.4 Mbps, bus loading = 100pF
> 		    = 320 ns for 3.4 Mbps, bus loading = 400pF
> 
> and section 3.15.4.6 says that when IC_CLK_FREQ_OPTIMIZATION = 1,
> 
>     MIN_SCL_HIGHtime = 60 ns for 3.4 Mbps, bus loading = 100pF
> 		     = 160 ns for 3.4 Mbps, bus loading = 400pF
>     MIN_SCL_LOWtime = 120 ns for 3.4 Mbps, bus loading = 100pF
> 		    = 320 ns for 3.4 Mbps, bus loading = 400pF
> 
> In order to calculate more accurate hs_hcnt amd hs_lcnt, two hardware
> parameters IC_CAP_LOADING and IC_CLK_FREQ_OPTIMIZATION must be
> considered together.

...

> +static void i2c_dw_fw_parse_hw_params(struct dw_i2c_dev *dev)

Separate function is an overkill. Just inline its contents...

...

> +	ret = device_property_read_u32(device, "bus-capacitance-pf", &dev->bus_capacitance_pf);
> +	if (ret || dev->bus_capacitance_pf < 400)
> +		dev->bus_capacitance_pf = 100;
> +	else
> +		dev->bus_capacitance_pf = 400;
> +
> +	dev->clk_freq_optimized = device_property_read_bool(device, "clk-freq-optimized");

...

>  	i2c_parse_fw_timings(device, t, false);
>  
> +	i2c_dw_fw_parse_hw_params(dev);

...here.

>  	i2c_dw_adjust_bus_speed(dev);

...

> + * @bus_capacitance_pf: bus capacitance in picofarad

picofarads

...

> +			u32 t_high, t_low;
> +
> +			if (dev->bus_capacitance_pf == 400) {
> +				t_high = dev->clk_freq_optimized ? 160 : 120;
> +				t_low = 320;
> +			} else {

Yeah, this has no protection against wrong values in the DT/ACPI.
So, perhaps

			} else if (...) {

and assign defaults or bail out with an error?

> +				t_high = 60;
> +				t_low = dev->clk_freq_optimized ? 120 : 160;
> +			}

-- 
With Best Regards,
Andy Shevchenko






[Index of Archives]     [Linux GPIO]     [Linux SPI]     [Linux Hardward Monitoring]     [LM Sensors]     [Linux USB Devel]     [Linux Media]     [Video for Linux]     [Linux Audio Users]     [Yosemite News]     [Linux Kernel]     [Linux SCSI]

  Powered by Linux