Re: [PATCH] i2c: i2c-qcom-geni: Serve transfer during early resume stage

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Tue, Apr 02, 2024 at 03:57:41PM +0530, Mukesh Kumar Savaliya wrote:
> pm_runtime_get_sync() function fails during PM early resume and returning
> -EACCES because runtime PM for the device is disabled at the early stage
> causing i2c transfer to fail. Make changes to serve transfer with force
> resume.
> 

I'm guessing that this is caused by some other driver that wants to
perform an I2C access during early resume? If so, can you describe what
that use case is?

Regards,
Bjorn

> 1. Register interrupt with IRQF_EARLY_RESUME and IRQF_NO_SUSPEND flags
>    to avoid timeout of transfer when IRQ is not enabled during early stage.
> 2. Do force resume if pm_runtime_get_sync() is failing after system
>    suspend when runtime PM is not enabled.
> 3. Increment power usage count after forced resume to balance
>    it against regular runtime suspend.
> 
> Co-developed-by: Viken Dadhaniya <quic_vdadhani@xxxxxxxxxxx>
> Signed-off-by: Viken Dadhaniya <quic_vdadhani@xxxxxxxxxxx>
> Signed-off-by: Mukesh Kumar Savaliya <quic_msavaliy@xxxxxxxxxxx>
> ---
> v1 -> v2:
> - Changed gi2c->se.dev to dev during dev_dbg() calls.
> - Addressed review comments from Andi.
> ---
>  drivers/i2c/busses/i2c-qcom-geni.c | 55 ++++++++++++++++++++++++------
>  1 file changed, 45 insertions(+), 10 deletions(-)
> 
> diff --git a/drivers/i2c/busses/i2c-qcom-geni.c b/drivers/i2c/busses/i2c-qcom-geni.c
> index da94df466e83..30c335b02ac4 100644
> --- a/drivers/i2c/busses/i2c-qcom-geni.c
> +++ b/drivers/i2c/busses/i2c-qcom-geni.c
> @@ -134,6 +134,8 @@ struct geni_i2c_clk_fld {
>  	u8	t_cycle_cnt;
>  };
>  
> +static int geni_i2c_runtime_resume(struct device *dev);
> +
>  /*
>   * Hardware uses the underlying formula to calculate time periods of
>   * SCL clock cycle. Firmware uses some additional cycles excluded from the
> @@ -677,22 +679,48 @@ static int geni_i2c_fifo_xfer(struct geni_i2c_dev *gi2c,
>  	return num;
>  }
>  
> +static int geni_i2c_force_resume(struct geni_i2c_dev *gi2c)
> +{
> +	struct device *dev = gi2c->se.dev;
> +	int ret;
> +
> +	ret = geni_i2c_runtime_resume(dev);
> +	if (ret) {
> +		dev_err(gi2c->se.dev, "Error turning SE resources:%d\n", ret);
> +		pm_runtime_put_noidle(dev);
> +		pm_runtime_set_suspended(dev);
> +		return ret;
> +	}
> +	pm_runtime_get_noresume(dev);
> +	pm_runtime_set_active(dev);
> +	return ret;
> +}
> +
>  static int geni_i2c_xfer(struct i2c_adapter *adap,
>  			 struct i2c_msg msgs[],
>  			 int num)
>  {
>  	struct geni_i2c_dev *gi2c = i2c_get_adapdata(adap);
> +	struct device *dev = gi2c->se.dev;
>  	int ret;
>  
>  	gi2c->err = 0;
>  	reinit_completion(&gi2c->done);
> -	ret = pm_runtime_get_sync(gi2c->se.dev);
> -	if (ret < 0) {
> -		dev_err(gi2c->se.dev, "error turning SE resources:%d\n", ret);
> -		pm_runtime_put_noidle(gi2c->se.dev);
> -		/* Set device in suspended since resume failed */
> -		pm_runtime_set_suspended(gi2c->se.dev);
> -		return ret;
> +
> +	if (!pm_runtime_enabled(dev) && gi2c->suspended) {
> +		dev_dbg(dev, "RT_PM disabled, Do force resume, pm_usage_count: %d\n",
> +			atomic_read(&dev->power.usage_count));
> +		ret = geni_i2c_force_resume(gi2c);
> +		if (ret)
> +			return ret;
> +	} else {
> +		ret = pm_runtime_get_sync(dev);
> +		if (ret == -EACCES && gi2c->suspended) {
> +			dev_dbg(dev, "PM get_sync() failed-%d, force resume\n", ret);
> +			ret = geni_i2c_force_resume(gi2c);
> +			if (ret)
> +				return ret;
> +		}
>  	}
>  
>  	qcom_geni_i2c_conf(gi2c);
> @@ -702,8 +730,15 @@ static int geni_i2c_xfer(struct i2c_adapter *adap,
>  	else
>  		ret = geni_i2c_fifo_xfer(gi2c, msgs, num);
>  
> -	pm_runtime_mark_last_busy(gi2c->se.dev);
> -	pm_runtime_put_autosuspend(gi2c->se.dev);
> +	if (!pm_runtime_enabled(dev) && !gi2c->suspended) {
> +		pm_runtime_put_noidle(dev);
> +		pm_runtime_set_suspended(dev);
> +		gi2c->suspended = 0;
> +	} else {
> +		pm_runtime_mark_last_busy(gi2c->se.dev);
> +		pm_runtime_put_autosuspend(gi2c->se.dev);
> +	}
> +
>  	gi2c->cur = NULL;
>  	gi2c->err = 0;
>  	return ret;
> @@ -820,7 +855,7 @@ static int geni_i2c_probe(struct platform_device *pdev)
>  	init_completion(&gi2c->done);
>  	spin_lock_init(&gi2c->lock);
>  	platform_set_drvdata(pdev, gi2c);
> -	ret = devm_request_irq(dev, gi2c->irq, geni_i2c_irq, 0,
> +	ret = devm_request_irq(dev, gi2c->irq, geni_i2c_irq, IRQF_EARLY_RESUME | IRQF_NO_SUSPEND,
>  			       dev_name(dev), gi2c);
>  	if (ret) {
>  		dev_err(dev, "Request_irq failed:%d: err:%d\n",
> -- 
> 2.25.1
> 




[Index of Archives]     [Linux GPIO]     [Linux SPI]     [Linux Hardward Monitoring]     [LM Sensors]     [Linux USB Devel]     [Linux Media]     [Video for Linux]     [Linux Audio Users]     [Yosemite News]     [Linux Kernel]     [Linux SCSI]

  Powered by Linux