On Tue 10 Sep 2024 at 09:48, Krzysztof Kozlowski <krzk@xxxxxxxxxx> wrote: > On Mon, Sep 09, 2024 at 05:39:03PM +0200, Jerome Brunet wrote: >> Add DT binding documentation for the Texas Instruments TPS25990 eFuse >> >> Signed-off-by: Jerome Brunet <jbrunet@xxxxxxxxxxxx> >> --- >> .../bindings/hwmon/pmbus/ti,tps25990.yaml | 73 ++++++++++++++++++++++ >> 1 file changed, 73 insertions(+) >> > > A nit, subject: drop second/last, redundant "documentation". The > "dt-bindings" prefix is already stating that these are bindings/docs. > See also: > https://elixir.bootlin.com/linux/v6.7-rc8/source/Documentation/devicetree/bindings/submitting-patches.rst#L18 > >> diff --git a/Documentation/devicetree/bindings/hwmon/pmbus/ti,tps25990.yaml b/Documentation/devicetree/bindings/hwmon/pmbus/ti,tps25990.yaml >> new file mode 100644 >> index 000000000000..e717942b3598 >> --- /dev/null >> +++ b/Documentation/devicetree/bindings/hwmon/pmbus/ti,tps25990.yaml >> @@ -0,0 +1,73 @@ >> +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) >> +%YAML 1.2 >> +--- >> + > > Drop blank line. > >> +$id: http://devicetree.org/schemas/hwmon/pmbus/ti,tps25990.yaml# >> +$schema: http://devicetree.org/meta-schemas/core.yaml# >> + >> +title: Texas Instruments TPS25990 Stackable eFuse >> + >> +maintainers: >> + - Jerome Brunet <jbrunet@xxxxxxxxxxxx> >> + >> +description: | > > Do not need '|' unless you need to preserve formatting. > >> + The TI TPS25990 is an integrated, high-current circuit >> + protection and power management device with PMBUS interface >> + >> +properties: >> + compatible: >> + const: ti,tps25990 >> + >> + reg: >> + maxItems: 1 >> + >> + ti,rimon-milli-ohms: >> + description: >> + milli Ohms value of the resistance installed between the Imon pin >> + and the ground reference. > > Ohms is not enough? We don't have mOhm in property units. > https://github.com/devicetree-org/dt-schema/blob/main/dtschema/schemas/property-units.yaml > Same discussion as we've had on the driver change. At the moment Ohms is enough for the cases I've seen. Will it be, not sure. Using mOhms is' way to avoid "S**t, R is 80.2 Ohms, I need another digit to not loose precision " kind of situation and introduce a second property just for that. No idea if Rimon will get that low. Probably not. I'll switch to Ohms. >> + >> + interrupts: >> + description: PMBUS SMB Alert Interrupt. >> + maxItems: 1 >> + >> + regulators: >> + type: object >> + description: >> + list of regulators provided by this controller. > > You have just one regulator, so drop "regulators" node and use directly > vout here. Just took the example the other pmbus device and did the same for consistency. In that case, there other (possible) regulator called gpdac1 and gpdac2. I haven't even tried to implement the support for those. Since it would not break old DTs to add that later, I thought it would be OK to add them later. Should I add them now ? > >> + >> + properties: >> + vout: >> + $ref: /schemas/regulator/regulator.yaml# >> + type: object >> + unevaluatedProperties: false >> + additionalProperties: false >> + >> +required: >> + - compatible >> + - reg >> + - ti,rimon-milli-ohms >> + >> +additionalProperties: false > > Best regards, > Krzysztof -- Jerome
