Add functions to perform block read and write operations. This applies
for cases where the requested operation is for >8 bytes of data.
When not using the block mode transfer, the driver will attempt a series
of 8 byte i2c operations until it reaches the desired total. For
example, for a 40 byte request the driver will complete 5 separate
transactions. This results in large transactions taking a
significant amount of time to process.
Add block mode such that the driver can request larger transactions, up
to 1024 bytes per transfer.
Many aspects of the block mode transfer is common with the regular 8
byte operations. Use generic functions for parts of the message
construction and sending the message. The key difference for the block
mode is the usage of separate FIFO buffer to store data.d
Write to this buffer in the case of a write (before command send).
Read from this buffer in the case of a read (after command send).
Data is written into this buffer by placing data into the MSB onwards.
This means the bottom 8 bits of the data will match the top 8 bits, and
so on and so forth.
Set specific bits in message for block mode, enable block mode transfers
from global i2c management registers, construct message, send message,
read or write from FIFO buffer as required.
The block-mode transactions result in a significant speed increase in
large i2c requests.
Signed-off-by: Aryan Srivastava <aryan.srivastava@xxxxxxxxxxxxxxxxxxx>
---
drivers/i2c/busses/i2c-octeon-core.c | 146 ++++++++++++++++++++++-
drivers/i2c/busses/i2c-octeon-core.h | 14 +++
drivers/i2c/busses/i2c-thunderx-pcidrv.c | 4 +
3 files changed, 158 insertions(+), 6 deletions(-)
diff --git a/drivers/i2c/busses/i2c-octeon-core.c b/drivers/i2c/busses/i2c-octeon-core.c
index 6772359ca6c8..03d30e179728 100644
--- a/drivers/i2c/busses/i2c-octeon-core.c
+++ b/drivers/i2c/busses/i2c-octeon-core.c
@@ -130,6 +130,25 @@ static void octeon_i2c_hlc_disable(struct octeon_i2c *i2c)
octeon_i2c_ctl_write(i2c, TWSI_CTL_ENAB);
}
+static void octeon_i2c_block_enable(struct octeon_i2c *i2c)
+{
+ if (i2c->block_enabled || !TWSI_BLOCK_CTL(i2c))
+ return;
+
+ i2c->block_enabled = true;
+ octeon_i2c_writeq_flush(TWSI_MODE_STRETCH
+ | TWSI_MODE_BLOCK_MODE, i2c->twsi_base + TWSI_MODE(i2c));
+}
+
+static void octeon_i2c_block_disable(struct octeon_i2c *i2c)
+{
+ if (!i2c->block_enabled || !TWSI_BLOCK_CTL(i2c))
+ return;
+
+ i2c->block_enabled = false;
+ octeon_i2c_writeq_flush(TWSI_MODE_STRETCH, i2c->twsi_base + TWSI_MODE(i2c));
+}
+
/**
* octeon_i2c_hlc_wait - wait for an HLC operation to complete
* @i2c: The struct octeon_i2c
@@ -268,6 +287,7 @@ static int octeon_i2c_start(struct octeon_i2c *i2c)
u8 stat;
octeon_i2c_hlc_disable(i2c);
+ octeon_i2c_block_disable(i2c);
octeon_i2c_ctl_write(i2c, TWSI_CTL_ENAB | TWSI_CTL_STA);
ret = octeon_i2c_wait(i2c);
@@ -606,6 +626,112 @@ static int octeon_i2c_hlc_comp_write(struct octeon_i2c *i2c, struct i2c_msg *msg
return ret;
}
+/**
+ * octeon_i2c_hlc_block_comp_read - high-level-controller composite block read
+ * @i2c: The struct octeon_i2c
+ * @msgs: msg[0] contains address, place read data into msg[1]
+ *
+ * i2c core command is constructed and written into the SW_TWSI register.
+ * The execution of the command will result in requested data being
+ * placed into a FIFO buffer, ready to be read.
+ * Used in the case where the i2c xfer is for greater than 8 bytes of read data.
+ *
+ * Returns 0 on success, otherwise a negative errno.
+ */
+static int octeon_i2c_hlc_block_comp_read(struct octeon_i2c *i2c, struct i2c_msg *msgs)
+{
+ int len, ret = 0;
+ u64 cmd = 0;
+
+ octeon_i2c_hlc_enable(i2c);
+ octeon_i2c_block_enable(i2c);
+
+ /* Write (size - 1) into block control register */
+ len = msgs[1].len - 1;
+ octeon_i2c_writeq_flush((u64)(len), i2c->twsi_base + TWSI_BLOCK_CTL(i2c));
+
+ /* Prepare core command */
+ cmd = SW_TWSI_V | SW_TWSI_R | SW_TWSI_SOVR;
+ cmd |= (u64)(msgs[0].addr & 0x7full) << SW_TWSI_ADDR_SHIFT;
+
+ /* Send core command */
+ ret = octeon_i2c_hlc_cmd(i2c, msgs[0], cmd);
+ if (ret)
+ return ret;
+
+ cmd = __raw_readq(i2c->twsi_base + SW_TWSI(i2c));
+ if ((cmd & SW_TWSI_R) == 0)
+ return octeon_i2c_check_status(i2c, false);
+
+ /* read data in FIFO */
+ octeon_i2c_writeq_flush(TWSI_BLOCK_STS_RESET_PTR, i2c->twsi_base + TWSI_BLOCK_STS(i2c));
+ for (int i = 0; i < len; i += 8) {
+ u64 rd = __raw_readq(i2c->twsi_base + TWSI_BLOCK_FIFO(i2c));
+ /* Place data into msg buf from FIFO, MSB onwards */
+ for (int j = 7; j >= 0; j--)
+ msgs[1].buf[i + (7 - j)] = (rd >> (8 * j)) & 0xff;
+ }
+
+ octeon_i2c_block_disable(i2c);
+ return ret;
+}
+
+/**
+ * octeon_i2c_hlc_block_comp_write - high-level-controller composite block write
+ * @i2c: The struct octeon_i2c
+ * @msgs: msg[0] contains address, msg[1] contains data to be written
+ *
+ * i2c core command is constructed and write data is written into the FIFO buffer.
+ * The execution of the command will result in HW write, using the data in FIFO.
+ * Used in the case where the i2c xfer is for greater than 8 bytes of write data.
+ *
+ * Returns 0 on success, otherwise a negative errno.
+ */
+static int octeon_i2c_hlc_block_comp_write(struct octeon_i2c *i2c, struct i2c_msg *msgs)
+{
+ bool set_ext = false;
+ int len, ret = 0;
+ u64 cmd, ext = 0;
+
+ octeon_i2c_hlc_enable(i2c);
+ octeon_i2c_block_enable(i2c);
+
+ /* Write (size - 1) into block control register */
+ len = msgs[1].len - 1;
+ octeon_i2c_writeq_flush((u64)(len), i2c->twsi_base + TWSI_BLOCK_CTL(i2c));
+
+ /* Prepare core command */
+ cmd = SW_TWSI_V | SW_TWSI_SOVR;
+ cmd |= (u64)(msgs[0].addr & 0x7full) << SW_TWSI_ADDR_SHIFT;
+
+ /* Set parameters for extended message (if required) */
+ set_ext = octeon_i2c_hlc_ext(i2c, msgs[0], &cmd, &ext);
+
+ /* Write msg into FIFO buffer */
+ octeon_i2c_writeq_flush(TWSI_BLOCK_STS_RESET_PTR, i2c->twsi_base + TWSI_BLOCK_STS(i2c));
+ for (int i = 0; i < len; i += 8) {
+ u64 buf = 0;
+ /* Place data from msg buf into FIFO, MSB onwards */
+ for (int j = 7; j >= 0; j--)
+ buf |= (msgs[1].buf[i + (7 - j)] << (8 * j));
+ octeon_i2c_writeq_flush(buf, i2c->twsi_base + TWSI_BLOCK_FIFO(i2c));
+ }
+ if (set_ext)
+ octeon_i2c_writeq_flush(ext, i2c->twsi_base + SW_TWSI_EXT(i2c));
+
+ /* Send command to core (send data in FIFO) */
+ ret = octeon_i2c_hlc_cmd_send(i2c, cmd);
+ if (ret)
+ return ret;
+
+ cmd = __raw_readq(i2c->twsi_base + SW_TWSI(i2c));
+ if ((cmd & SW_TWSI_R) == 0)
+ return octeon_i2c_check_status(i2c, false);
+
+ octeon_i2c_block_disable(i2c);
+ return ret;
+}
+
/**
* octeon_i2c_xfer - The driver's master_xfer function
* @adap: Pointer to the i2c_adapter structure
@@ -631,13 +757,21 @@ int octeon_i2c_xfer(struct i2c_adapter *adap, struct i2c_msg *msgs, int num)
if ((msgs[0].flags & I2C_M_RD) == 0 &&
(msgs[1].flags & I2C_M_RECV_LEN) == 0 &&
msgs[0].len > 0 && msgs[0].len <= 2 &&
- msgs[1].len > 0 && msgs[1].len <= 8 &&
+ msgs[1].len > 0 &&
msgs[0].addr == msgs[1].addr) {
- if (msgs[1].flags & I2C_M_RD)
- ret = octeon_i2c_hlc_comp_read(i2c, msgs);
- else
- ret = octeon_i2c_hlc_comp_write(i2c, msgs);
- goto out;
+ if (msgs[1].len <= 8) {
+ if (msgs[1].flags & I2C_M_RD)
+ ret = octeon_i2c_hlc_comp_read(i2c, msgs);
+ else
+ ret = octeon_i2c_hlc_comp_write(i2c, msgs);
+ goto out;
+ } else if (msgs[1].len <= 1024 && TWSI_BLOCK_CTL(i2c)) {
+ if (msgs[1].flags & I2C_M_RD)
+ ret = octeon_i2c_hlc_block_comp_read(i2c, msgs);
+ else
+ ret = octeon_i2c_hlc_block_comp_write(i2c, msgs);
+ goto out;
+ }
}
}
diff --git a/drivers/i2c/busses/i2c-octeon-core.h b/drivers/i2c/busses/i2c-octeon-core.h
index 9bb9f64fdda0..81fcf413c890 100644
--- a/drivers/i2c/busses/i2c-octeon-core.h
+++ b/drivers/i2c/busses/i2c-octeon-core.h
@@ -85,6 +85,11 @@
#define TWSI_INT_SDA BIT_ULL(10)
#define TWSI_INT_SCL BIT_ULL(11)
+#define TWSI_MODE_STRETCH BIT_ULL(1)
+#define TWSI_MODE_BLOCK_MODE BIT_ULL(2)
+
+#define TWSI_BLOCK_STS_RESET_PTR BIT_ULL(0)
+#define TWSI_BLOCK_STS_BUSY BIT_ULL(1)
#define I2C_OCTEON_EVENT_WAIT 80 /* microseconds */
/* Register offsets */
@@ -92,11 +97,19 @@ struct octeon_i2c_reg_offset {
unsigned int sw_twsi;
unsigned int twsi_int;
unsigned int sw_twsi_ext;
+ unsigned int twsi_mode;
+ unsigned int twsi_block_ctl;
+ unsigned int twsi_block_sts;
+ unsigned int twsi_block_fifo;
};
#define SW_TWSI(x) (x->roff.sw_twsi)
#define TWSI_INT(x) (x->roff.twsi_int)
#define SW_TWSI_EXT(x) (x->roff.sw_twsi_ext)
+#define TWSI_MODE(x) (x->roff.twsi_mode)
+#define TWSI_BLOCK_CTL(x) (x->roff.twsi_block_ctl)
+#define TWSI_BLOCK_STS(x) (x->roff.twsi_block_sts)
+#define TWSI_BLOCK_FIFO(x) (x->roff.twsi_block_fifo)
struct octeon_i2c {
wait_queue_head_t queue;
@@ -110,6 +123,7 @@ struct octeon_i2c {
void __iomem *twsi_base;
struct device *dev;
bool hlc_enabled;
+ bool block_enabled;
bool broken_irq_mode;
bool broken_irq_check;
void (*int_enable)(struct octeon_i2c *);
diff --git a/drivers/i2c/busses/i2c-thunderx-pcidrv.c b/drivers/i2c/busses/i2c-thunderx-pcidrv.c
index a77cd86fe75e..abde98117d7e 100644
--- a/drivers/i2c/busses/i2c-thunderx-pcidrv.c
+++ b/drivers/i2c/busses/i2c-thunderx-pcidrv.c
@@ -165,6 +165,10 @@ static int thunder_i2c_probe_pci(struct pci_dev *pdev,
i2c->roff.sw_twsi = 0x1000;
i2c->roff.twsi_int = 0x1010;
i2c->roff.sw_twsi_ext = 0x1018;
+ i2c->roff.twsi_mode = 0x1038;
+ i2c->roff.twsi_block_ctl = 0x1048;
+ i2c->roff.twsi_block_sts = 0x1050;
+ i2c->roff.twsi_block_fifo = 0x1058;
i2c->dev = dev;
pci_set_drvdata(pdev, i2c);
--
2.43.2
