Re: [PATCH v6 10/11] ARM: dts: stm32: add ETZPC as a system bus for STM32MP15x boards

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Hi Rob,

On 10/12/23 17:30, Rob Herring wrote:
On Wed, Oct 11, 2023 at 10:49:58AM +0200, Gatien CHEVALLIER wrote:
Hi Rob,

On 10/10/23 20:42, Rob Herring wrote:
On Tue, Oct 10, 2023 at 02:57:18PM +0200, Gatien Chevallier wrote:
ETZPC is a firewall controller. Put all peripherals filtered by the
ETZPC as ETZPC subnodes and reference ETZPC as an
access-control-provider.

For more information on which peripheral is securable or supports MCU
isolation, please read the STM32MP15 reference manual.

Signed-off-by: Gatien Chevallier <gatien.chevallier@xxxxxxxxxxx>
---

Changes in V6:
      	- Renamed access-controller to access-controllers
      	- Removal of access-control-provider property

Changes in V5:
      	- Renamed feature-domain* to access-control*

   arch/arm/boot/dts/st/stm32mp151.dtsi  | 2756 +++++++++++++------------
   arch/arm/boot/dts/st/stm32mp153.dtsi  |   52 +-
   arch/arm/boot/dts/st/stm32mp15xc.dtsi |   19 +-
   3 files changed, 1450 insertions(+), 1377 deletions(-)

This is not reviewable. Change the indentation and any non-functional
change in one patch and then actual changes in another.

Ok, I'll make it easier to read.


This is also an ABI break. Though I'm not sure it's avoidable. All the
devices below the ETZPC node won't probe on existing kernel. A
simple-bus fallback for ETZPC node should solve that.


I had one issue when trying with a simple-bus fallback that was the
drivers were probing even though the access rights aren't correct.
Hence the removal of the simple-bus compatible in the STM32MP25 patch.

But it worked before, right? So the difference is you have either added
new devices which need setup or your firmware changed how devices are
setup (or not setup). Certainly can't fix the latter case. You just need
to be explicit about what you are doing to users.


I should've specified it was during a test where I deliberately set
incorrect rights on a peripheral and enabled its node to see if the
firewall would allow the creation of the device.


Even though a node is tagged with the OF_POPULATED flag when checking
the access rights with the firewall controller, it seems that when
simple-bus is probing, there's no check of this flag.

It shouldn't. Those flags are for creating the devices (or not) and
removing only devices of_platform_populate() created.


About the "simple-bus" being a fallback, I think I understood why I saw
that the devices were created.

All devices under a node whose compatible is "simple-bus" are created
in of_platform_device_create_pdata(), called by
of_platform_default_populate_init() at arch_initcall level. This
before the firewall-controller has a chance to populate it's bus.

Therefore, when I flag nodes when populating the firewall-bus, the
devices are already created. The "simple-bus" mechanism is not a
fallback here as it precedes the driver probe.

Is there a safe way to safely remove/disable a device created this way?
Devices that are under the firewall controller (simple-bus) node
should not be probed before it as they're child of it.

Best regards,
Gatien

of_platform_populate() checks and sets the OF_POPULATED_BUS flag.
Maybe that is my error and the firewall bus populate should set
OF_POPULATED_BUS instead of OF_POPULATED. Is that correct?

Shrug. Off hand, I'd say probably not, but am not certain.

Rob



[Index of Archives]     [Linux GPIO]     [Linux SPI]     [Linux Hardward Monitoring]     [LM Sensors]     [Linux USB Devel]     [Linux Media]     [Video for Linux]     [Linux Audio Users]     [Yosemite News]     [Linux Kernel]     [Linux SCSI]

  Powered by Linux