We found that when the interrupt bit of the IIC controller is cleared,
the ack/nack bit is also cleared at the same time. After clearing the
interrupt bit in sprd_i2c_isr(), incorrect ack/nack information will be
obtained in sprd_i2c_isr_thread(), resulting in incorrect communication
when nack cannot be recognized. To solve this problem, we used a global
variable to record ack/nack information before clearing the interrupt
bit instead of a local variable.
Signed-off-by: Huangzheng Lai <Huangzheng.Lai@xxxxxxxxxx>
---
drivers/i2c/busses/i2c-sprd.c | 10 +++++-----
1 file changed, 5 insertions(+), 5 deletions(-)
diff --git a/drivers/i2c/busses/i2c-sprd.c b/drivers/i2c/busses/i2c-sprd.c
index 066b3a9c30c8..549b60dd3273 100644
--- a/drivers/i2c/busses/i2c-sprd.c
+++ b/drivers/i2c/busses/i2c-sprd.c
@@ -85,6 +85,7 @@ struct sprd_i2c {
struct clk *clk;
u32 src_clk;
u32 bus_freq;
+ bool ack_flag;
struct completion complete;
struct reset_control *rst;
u8 *buf;
@@ -384,7 +385,6 @@ static irqreturn_t sprd_i2c_isr_thread(int irq, void *dev_id)
{
struct sprd_i2c *i2c_dev = dev_id;
struct i2c_msg *msg = i2c_dev->msg;
- bool ack = !(readl(i2c_dev->base + I2C_STATUS) & I2C_RX_ACK);
u32 i2c_tran;
if (msg->flags & I2C_M_RD)
@@ -400,7 +400,7 @@ static irqreturn_t sprd_i2c_isr_thread(int irq, void *dev_id)
* For reading data, ack is always true, if i2c_tran is not 0 which
* means we still need to contine to read data from slave.
*/
- if (i2c_tran && ack) {
+ if (i2c_tran && i2c_dev->ack_flag) {
sprd_i2c_data_transfer(i2c_dev);
return IRQ_HANDLED;
}
@@ -411,7 +411,7 @@ static irqreturn_t sprd_i2c_isr_thread(int irq, void *dev_id)
* If we did not get one ACK from slave when writing data, we should
* return -EIO to notify users.
*/
- if (!ack)
+ if (!i2c_dev->ack_flag)
i2c_dev->err = -EIO;
else if (msg->flags & I2C_M_RD && i2c_dev->count)
sprd_i2c_read_bytes(i2c_dev, i2c_dev->buf, i2c_dev->count);
@@ -428,7 +428,6 @@ static irqreturn_t sprd_i2c_isr(int irq, void *dev_id)
{
struct sprd_i2c *i2c_dev = dev_id;
struct i2c_msg *msg = i2c_dev->msg;
- bool ack = !(readl(i2c_dev->base + I2C_STATUS) & I2C_RX_ACK);
u32 i2c_tran;
if (msg->flags & I2C_M_RD)
@@ -447,7 +446,8 @@ static irqreturn_t sprd_i2c_isr(int irq, void *dev_id)
* means we can read all data in one time, then we can finish this
* transmission too.
*/
- if (!i2c_tran || !ack) {
+ i2c_dev->ack_flag = !(readl(i2c_dev->base + I2C_STATUS) & I2C_RX_ACK);
+ if (!i2c_tran || !i2c_dev->ack_flag) {
sprd_i2c_clear_start(i2c_dev);
sprd_i2c_clear_irq(i2c_dev);
}
--
2.17.1
