[PATCH v9 2/2] i2c: aspeed: support ast2600 i2c new register mode driver

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Add i2c new register mode driver to support AST2600 i2c
new register mode. AST2600 i2c controller have legacy and
new register mode. The new register mode have global register
support 4 base clock for scl clock selection, and new clock
divider mode. The i2c new register mode have separate register
set to control i2c master and slave.

Signed-off-by: Ryan Chen <ryan_chen@xxxxxxxxxxxxxx>
---
 MAINTAINERS                      |    9 +
 drivers/i2c/busses/Kconfig       |   11 +
 drivers/i2c/busses/Makefile      |    1 +
 drivers/i2c/busses/i2c-ast2600.c | 1602 ++++++++++++++++++++++++++++++
 4 files changed, 1623 insertions(+)
 create mode 100644 drivers/i2c/busses/i2c-ast2600.c

diff --git a/MAINTAINERS b/MAINTAINERS
index 749710e22b4d..433ec2309441 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -1924,6 +1924,15 @@ F:	Documentation/devicetree/bindings/interrupt-controller/aspeed,ast2400-i2c-ic.
 F:	drivers/i2c/busses/i2c-aspeed.c
 F:	drivers/irqchip/irq-aspeed-i2c-ic.c
 
+ARM/ASPEED I2CV2 DRIVER
+M:	Ryan Chen <ryan_chen@xxxxxxxxxxxxxx>
+R:	Andrew Jeffery <andrew@xxxxxxxx>
+L:	linux-i2c@xxxxxxxxxxxxxxx
+L:	openbmc@xxxxxxxxxxxxxxxx (moderated for non-subscribers)
+S:	Maintained
+F:	Documentation/devicetree/bindings/i2c/aspeed,i2c.yaml
+F:	drivers/i2c/busses/i2c-ast2600.c
+
 ARM/ASPEED MACHINE SUPPORT
 M:	Joel Stanley <joel@xxxxxxxxx>
 R:	Andrew Jeffery <andrew@xxxxxxxx>
diff --git a/drivers/i2c/busses/Kconfig b/drivers/i2c/busses/Kconfig
index 7284206b278b..4f6935866257 100644
--- a/drivers/i2c/busses/Kconfig
+++ b/drivers/i2c/busses/Kconfig
@@ -389,6 +389,17 @@ config I2C_ALTERA
 	  This driver can also be built as a module.  If so, the module
 	  will be called i2c-altera.
 
+config I2C_AST2600
+	tristate "Aspeed I2C v2 Controller"
+	depends on ARCH_ASPEED || COMPILE_TEST
+	select I2C_SMBUS
+	help
+	  If you say yes to this option, support will be included for the
+	  Aspeed I2C controller with new register set.
+
+	  This driver can also be built as a module.  If so, the module
+	  will be called i2c-ast2600.
+
 config I2C_ASPEED
 	tristate "Aspeed I2C Controller"
 	depends on ARCH_ASPEED || COMPILE_TEST
diff --git a/drivers/i2c/busses/Makefile b/drivers/i2c/busses/Makefile
index c5cac15f075c..d0ab4d45781c 100644
--- a/drivers/i2c/busses/Makefile
+++ b/drivers/i2c/busses/Makefile
@@ -38,6 +38,7 @@ obj-$(CONFIG_I2C_POWERMAC)	+= i2c-powermac.o
 obj-$(CONFIG_I2C_ALTERA)	+= i2c-altera.o
 obj-$(CONFIG_I2C_AMD_MP2)	+= i2c-amd-mp2-pci.o i2c-amd-mp2-plat.o
 obj-$(CONFIG_I2C_ASPEED)	+= i2c-aspeed.o
+obj-$(CONFIG_I2C_AST2600)	+= i2c-ast2600.o
 obj-$(CONFIG_I2C_AT91)		+= i2c-at91.o
 i2c-at91-objs			:= i2c-at91-core.o i2c-at91-master.o
 ifeq ($(CONFIG_I2C_AT91_SLAVE_EXPERIMENTAL),y)
diff --git a/drivers/i2c/busses/i2c-ast2600.c b/drivers/i2c/busses/i2c-ast2600.c
new file mode 100644
index 000000000000..c8817fe9b23f
--- /dev/null
+++ b/drivers/i2c/busses/i2c-ast2600.c
@@ -0,0 +1,1602 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * ASPEED AST2600 new register set I2C controller driver
+ *
+ * Copyright (C) ASPEED Technology Inc.
+ */
+#include <linux/clk.h>
+#include <linux/err.h>
+#include <linux/i2c.h>
+#include <linux/io.h>
+#include <linux/slab.h>
+#include <linux/delay.h>
+#include <linux/reset.h>
+#include <linux/module.h>
+#include <linux/interrupt.h>
+#include <linux/completion.h>
+#include <linux/of.h>
+#include <linux/of_irq.h>
+#include <linux/mfd/syscon.h>
+#include <linux/regmap.h>
+#include <linux/of_device.h>
+#include <linux/dma-mapping.h>
+#include <linux/i2c-smbus.h>
+
+/*
+ * APB clk : 100Mhz
+ * div	: scl		: baseclk [APB/((div/2) + 1)] : tBuf [1/bclk * 16]
+ * I2CG10[31:24] base clk4 for i2c auto recovery timeout counter (0xC6)
+ * I2CG10[23:16] base clk3 for Standard-mode (100Khz) min tBuf 4.7us
+ * 0x3c : 100.8Khz	: 3.225Mhz					  : 4.96us
+ * 0x3d : 99.2Khz	: 3.174Mhz					  : 5.04us
+ * 0x3e : 97.65Khz	: 3.125Mhz					  : 5.12us
+ * 0x40 : 97.75Khz	: 3.03Mhz					  : 5.28us
+ * 0x41 : 99.5Khz	: 2.98Mhz					  : 5.36us (default)
+ * I2CG10[15:8] base clk2 for Fast-mode (400Khz) min tBuf 1.3us
+ * 0x12 : 400Khz	: 10Mhz						  : 1.6us
+ * I2CG10[7:0] base clk1 for Fast-mode Plus (1Mhz) min tBuf 0.5us
+ * 0x08 : 1Mhz		: 20Mhz						  : 0.8us
+ */
+#define AST2600_I2CG_ISR			0x00
+#define AST2600_I2CG_SLAVE_ISR		0x04
+#define AST2600_I2CG_OWNER		0x08
+#define AST2600_I2CG_CTRL		0x0C
+#define AST2600_I2CG_CLK_DIV_CTRL	0x10
+
+#define AST2600_I2CG_SLAVE_PKT_NAK	BIT(4)
+#define AST2600_I2CG_M_S_SEPARATE_INTR	BIT(3)
+#define AST2600_I2CG_CTRL_NEW_REG	BIT(2)
+#define AST2600_I2CG_CTRL_NEW_CLK_DIV	BIT(1)
+
+#define AST2600_GLOBAL_INIT				\
+			(AST2600_I2CG_CTRL_NEW_REG |	\
+			AST2600_I2CG_CTRL_NEW_CLK_DIV)
+#define I2CCG_DIV_CTRL 0xC6411208
+
+/* 0x00 : I2CC Master/Slave Function Control Register  */
+#define AST2600_I2CC_FUN_CTRL		0x00
+#define AST2600_I2CC_SLAVE_ADDR_RX_EN		BIT(20)
+#define AST2600_I2CC_MASTER_RETRY_MASK		GENMASK(19, 18)
+#define AST2600_I2CC_MASTER_RETRY(x)		(((x) & GENMASK(1, 0)) << 18)
+#define AST2600_I2CC_BUS_AUTO_RELEASE		BIT(17)
+#define AST2600_I2CC_M_SDA_LOCK_EN			BIT(16)
+#define AST2600_I2CC_MULTI_MASTER_DIS		BIT(15)
+#define AST2600_I2CC_M_SCL_DRIVE_EN			BIT(14)
+#define AST2600_I2CC_MSB_STS				BIT(9)
+#define AST2600_I2CC_SDA_DRIVE_1T_EN		BIT(8)
+#define AST2600_I2CC_M_SDA_DRIVE_1T_EN		BIT(7)
+#define AST2600_I2CC_M_HIGH_SPEED_EN		BIT(6)
+/* reserver 5 : 2 */
+#define AST2600_I2CC_SLAVE_EN			BIT(1)
+#define AST2600_I2CC_MASTER_EN			BIT(0)
+
+/* 0x04 : I2CC Master/Slave Clock and AC Timing Control Register #1 */
+#define AST2600_I2CC_AC_TIMING		0x04
+#define AST2600_I2CC_TTIMEOUT(x)			(((x) & GENMASK(4, 0)) << 24)
+#define AST2600_I2CC_TCKHIGHMIN(x)			(((x) & GENMASK(3, 0)) << 20)
+#define AST2600_I2CC_TCKHIGH(x)			(((x) & GENMASK(3, 0)) << 16)
+#define AST2600_I2CC_TCKLOW(x)			(((x) & GENMASK(3, 0)) << 12)
+#define AST2600_I2CC_THDDAT(x)			(((x) & GENMASK(1, 0)) << 10)
+#define AST2600_I2CC_TOUTBASECLK(x)			(((x) & GENMASK(1, 0)) << 8)
+#define AST2600_I2CC_TBASECLK(x)			((x) & GENMASK(3, 0))
+
+/* 0x08 : I2CC Master/Slave Transmit/Receive Byte Buffer Register */
+#define AST2600_I2CC_STS_AND_BUFF		0x08
+#define AST2600_I2CC_TX_DIR_MASK			GENMASK(31, 29)
+#define AST2600_I2CC_SDA_OE				BIT(28)
+#define AST2600_I2CC_SDA_O				BIT(27)
+#define AST2600_I2CC_SCL_OE				BIT(26)
+#define AST2600_I2CC_SCL_O				BIT(25)
+
+#define AST2600_I2CC_SCL_LINE_STS			BIT(18)
+#define AST2600_I2CC_SDA_LINE_STS			BIT(17)
+#define AST2600_I2CC_BUS_BUSY_STS			BIT(16)
+
+#define AST2600_I2CC_GET_RX_BUFF(x)			(((x) >> 8) & GENMASK(7, 0))
+
+/* 0x0C : I2CC Master/Slave Pool Buffer Control Register  */
+#define AST2600_I2CC_BUFF_CTRL		0x0C
+#define AST2600_I2CC_GET_RX_BUF_LEN(x)		(((x) >> 24) & GENMASK(5, 0))
+#define AST2600_I2CC_SET_RX_BUF_LEN(x)		(((((x) - 1) & GENMASK(4, 0)) << 16) | BIT(0))
+#define AST2600_I2CC_SET_TX_BUF_LEN(x)		(((((x) - 1) & GENMASK(4, 0)) << 8) | BIT(0))
+#define AST2600_I2CC_GET_TX_BUF_LEN(x)		((((x) >> 8) & GENMASK(4, 0)) + 1)
+
+/* 0x10 : I2CM Master Interrupt Control Register */
+#define AST2600_I2CM_IER			0x10
+/* 0x14 : I2CM Master Interrupt Status Register   : WC */
+#define AST2600_I2CM_ISR			0x14
+
+#define AST2600_I2CM_PKT_TIMEOUT			BIT(18)
+#define AST2600_I2CM_PKT_ERROR			BIT(17)
+#define AST2600_I2CM_PKT_DONE			BIT(16)
+
+#define AST2600_I2CM_BUS_RECOVER_FAIL		BIT(15)
+#define AST2600_I2CM_SDA_DL_TO			BIT(14)
+#define AST2600_I2CM_BUS_RECOVER			BIT(13)
+#define AST2600_I2CM_SMBUS_ALT			BIT(12)
+
+#define AST2600_I2CM_SCL_LOW_TO			BIT(6)
+#define AST2600_I2CM_ABNORMAL			BIT(5)
+#define AST2600_I2CM_NORMAL_STOP			BIT(4)
+#define AST2600_I2CM_ARBIT_LOSS			BIT(3)
+#define AST2600_I2CM_RX_DONE			BIT(2)
+#define AST2600_I2CM_TX_NAK				BIT(1)
+#define AST2600_I2CM_TX_ACK				BIT(0)
+
+/* 0x18 : I2CM Master Command/Status Register   */
+#define AST2600_I2CM_CMD_STS		0x18
+#define AST2600_I2CM_PKT_ADDR(x)			(((x) & GENMASK(6, 0)) << 24)
+#define AST2600_I2CM_PKT_EN				BIT(16)
+#define AST2600_I2CM_SDA_OE_OUT_DIR			BIT(15)
+#define AST2600_I2CM_SDA_O_OUT_DIR			BIT(14)
+#define AST2600_I2CM_SCL_OE_OUT_DIR			BIT(13)
+#define AST2600_I2CM_SCL_O_OUT_DIR			BIT(12)
+#define AST2600_I2CM_RECOVER_CMD_EN			BIT(11)
+
+#define AST2600_I2CM_RX_DMA_EN			BIT(9)
+#define AST2600_I2CM_TX_DMA_EN			BIT(8)
+/* Command Bit */
+#define AST2600_I2CM_RX_BUFF_EN			BIT(7)
+#define AST2600_I2CM_TX_BUFF_EN			BIT(6)
+#define AST2600_I2CM_STOP_CMD			BIT(5)
+#define AST2600_I2CM_RX_CMD_LAST			BIT(4)
+#define AST2600_I2CM_RX_CMD				BIT(3)
+
+#define AST2600_I2CM_TX_CMD				BIT(1)
+#define AST2600_I2CM_START_CMD			BIT(0)
+
+/* 0x1C : I2CM Master DMA Transfer Length Register	 */
+#define AST2600_I2CM_DMA_LEN		0x1C
+/* Tx Rx support length 1 ~ 4096 */
+#define AST2600_I2CM_SET_RX_DMA_LEN(x)	((((x) & GENMASK(11, 0)) << 16) | BIT(31))
+#define AST2600_I2CM_SET_TX_DMA_LEN(x)	(((x) & GENMASK(11, 0)) | BIT(15))
+
+/* 0x20 : I2CS Slave Interrupt Control Register   */
+#define AST2600_I2CS_IER			0x20
+/* 0x24 : I2CS Slave Interrupt Status Register	 */
+#define AST2600_I2CS_ISR			0x24
+
+#define AST2600_I2CS_ADDR_INDICATE_MASK	GENMASK(31, 30)
+#define AST2600_I2CS_SLAVE_PENDING			BIT(29)
+
+#define AST2600_I2CS_WAIT_TX_DMA			BIT(25)
+#define AST2600_I2CS_WAIT_RX_DMA			BIT(24)
+
+#define AST2600_I2CS_ADDR3_NAK			BIT(22)
+#define AST2600_I2CS_ADDR2_NAK			BIT(21)
+#define AST2600_I2CS_ADDR1_NAK			BIT(20)
+
+#define AST2600_I2CS_ADDR_MASK			GENMASK(19, 18)
+#define AST2600_I2CS_PKT_ERROR			BIT(17)
+#define AST2600_I2CS_PKT_DONE			BIT(16)
+#define AST2600_I2CS_INACTIVE_TO			BIT(15)
+
+#define AST2600_I2CS_SLAVE_MATCH			BIT(7)
+#define AST2600_I2CS_ABNOR_STOP			BIT(5)
+#define AST2600_I2CS_STOP				BIT(4)
+#define AST2600_I2CS_RX_DONE_NAK			BIT(3)
+#define AST2600_I2CS_RX_DONE			BIT(2)
+#define AST2600_I2CS_TX_NAK				BIT(1)
+#define AST2600_I2CS_TX_ACK				BIT(0)
+
+/* 0x28 : I2CS Slave CMD/Status Register   */
+#define AST2600_I2CS_CMD_STS		0x28
+#define AST2600_I2CS_ACTIVE_ALL			GENMASK(18, 17)
+#define AST2600_I2CS_PKT_MODE_EN			BIT(16)
+#define AST2600_I2CS_AUTO_NAK_NOADDR		BIT(15)
+#define AST2600_I2CS_AUTO_NAK_EN			BIT(14)
+
+#define AST2600_I2CS_ALT_EN				BIT(10)
+#define AST2600_I2CS_RX_DMA_EN			BIT(9)
+#define AST2600_I2CS_TX_DMA_EN			BIT(8)
+#define AST2600_I2CS_RX_BUFF_EN			BIT(7)
+#define AST2600_I2CS_TX_BUFF_EN			BIT(6)
+#define AST2600_I2CS_RX_CMD_LAST			BIT(4)
+
+#define AST2600_I2CS_TX_CMD				BIT(2)
+
+#define AST2600_I2CS_DMA_LEN		0x2C
+#define AST2600_I2CS_SET_RX_DMA_LEN(x)	(((((x) - 1) & GENMASK(11, 0)) << 16) | BIT(31))
+#define AST2600_I2CS_RX_DMA_LEN_MASK	(GENMASK(11, 0) << 16)
+
+#define AST2600_I2CS_SET_TX_DMA_LEN(x)	((((x) - 1) & GENMASK(11, 0)) | BIT(15))
+#define AST2600_I2CS_TX_DMA_LEN_MASK	GENMASK(11, 0)
+
+/* I2CM Master DMA Tx Buffer Register   */
+#define AST2600_I2CM_TX_DMA			0x30
+/* I2CM Master DMA Rx Buffer Register	*/
+#define AST2600_I2CM_RX_DMA			0x34
+/* I2CS Slave DMA Tx Buffer Register   */
+#define AST2600_I2CS_TX_DMA			0x38
+/* I2CS Slave DMA Rx Buffer Register   */
+#define AST2600_I2CS_RX_DMA			0x3C
+
+#define AST2600_I2CS_ADDR_CTRL		0x40
+
+#define	AST2600_I2CS_ADDR3_MASK		GENMASK(22, 16)
+#define	AST2600_I2CS_ADDR2_MASK		GENMASK(14, 8)
+#define	AST2600_I2CS_ADDR1_MASK		GENMASK(6, 0)
+
+#define AST2600_I2CM_DMA_LEN_STS		0x48
+#define AST2600_I2CS_DMA_LEN_STS		0x4C
+
+#define AST2600_I2C_GET_TX_DMA_LEN(x)		((x) & GENMASK(12, 0))
+#define AST2600_I2C_GET_RX_DMA_LEN(x)		(((x) >> 16) & GENMASK(12, 0))
+
+/* 0x40 : Slave Device Address Register */
+#define AST2600_I2CS_ADDR3_ENABLE			BIT(23)
+#define AST2600_I2CS_ADDR3(x)			((x) << 16)
+#define AST2600_I2CS_ADDR2_ENABLE			BIT(15)
+#define AST2600_I2CS_ADDR2(x)			((x) << 8)
+#define AST2600_I2CS_ADDR1_ENABLE			BIT(7)
+#define AST2600_I2CS_ADDR1(x)			(x)
+
+#define I2C_SLAVE_MSG_BUF_SIZE		256
+
+#define AST2600_I2C_DMA_SIZE		4096
+
+#define MASTER_TRIGGER_LAST_STOP	(AST2600_I2CM_RX_CMD_LAST | AST2600_I2CM_STOP_CMD)
+#define SLAVE_TRIGGER_CMD	(AST2600_I2CS_ACTIVE_ALL | AST2600_I2CS_PKT_MODE_EN)
+
+#define AST_I2C_TIMEOUT_CLK		0x2
+
+struct ast2600_i2c_timing_table {
+	u32 divisor;
+	u32 timing;
+};
+
+enum xfer_mode {
+	BYTE_MODE = 0,
+	BUFF_MODE,
+	DMA_MODE,
+};
+
+struct ast2600_i2c_bus {
+	struct i2c_adapter		adap;
+	struct device			*dev;
+	void __iomem			*reg_base;
+	struct regmap			*global_regs;
+	struct reset_control		*rst;
+	int				irq;
+	enum xfer_mode			mode;
+	struct clk			*clk;
+	u32				apb_clk;
+	u32				bus_frequency;
+	int				slave_operate;
+	u32				timeout;
+	/* smbus alert */
+	int				alert_enable;
+	struct i2c_smbus_alert_setup	alert_data;
+	struct i2c_client		*ara;
+	/* Multi-master */
+	bool				multi_master;
+	/* master structure */
+	int				cmd_err;
+	struct completion		cmd_complete;
+	struct i2c_msg			*msgs;
+	size_t				buf_index;
+	/* cur xfer msgs index*/
+	int				msgs_index;
+	int				msgs_count;
+	u8				*master_safe_buf;
+	dma_addr_t			master_dma_addr;
+	/*total xfer count */
+	int				master_xfer_cnt;
+	/* Buffer mode */
+	void __iomem			*buf_base;
+	size_t				buf_size;
+	/* Slave structure */
+	int				slave_xfer_len;
+	int				slave_xfer_cnt;
+#ifdef CONFIG_I2C_SLAVE
+	unsigned char			*slave_dma_buf;
+	dma_addr_t			slave_dma_addr;
+	struct i2c_client		*slave;
+#endif
+};
+
+static u32 ast2600_select_i2c_clock(struct ast2600_i2c_bus *i2c_bus)
+{
+	unsigned long base_clk1;
+	unsigned long base_clk2;
+	unsigned long base_clk3;
+	unsigned long base_clk4;
+	int baseclk_idx;
+	u32 clk_div_reg;
+	u32 scl_low;
+	u32 scl_high;
+	int divisor;
+	int inc = 0;
+	u32 data;
+
+	regmap_read(i2c_bus->global_regs, AST2600_I2CG_CLK_DIV_CTRL, &clk_div_reg);
+	base_clk1 = (i2c_bus->apb_clk * 10) / ((((clk_div_reg & 0xff) + 2) * 10) / 2);
+	base_clk2 = (i2c_bus->apb_clk * 10) /
+			(((((clk_div_reg >> 8) & 0xff) + 2) * 10) / 2);
+	base_clk3 = (i2c_bus->apb_clk * 10) /
+			(((((clk_div_reg >> 16) & 0xff) + 2) * 10) / 2);
+	base_clk4 = (i2c_bus->apb_clk * 10) /
+			(((((clk_div_reg >> 24) & 0xff) + 2) * 10) / 2);
+
+	if ((i2c_bus->apb_clk / i2c_bus->bus_frequency) <= 32) {
+		baseclk_idx = 0;
+		divisor = DIV_ROUND_UP(i2c_bus->apb_clk, i2c_bus->bus_frequency);
+	} else if ((base_clk1 / i2c_bus->bus_frequency) <= 32) {
+		baseclk_idx = 1;
+		divisor = DIV_ROUND_UP(base_clk1, i2c_bus->bus_frequency);
+	} else if ((base_clk2 / i2c_bus->bus_frequency) <= 32) {
+		baseclk_idx = 2;
+		divisor = DIV_ROUND_UP(base_clk2, i2c_bus->bus_frequency);
+	} else if ((base_clk3 / i2c_bus->bus_frequency) <= 32) {
+		baseclk_idx = 3;
+		divisor = DIV_ROUND_UP(base_clk3, i2c_bus->bus_frequency);
+	} else {
+		baseclk_idx = 4;
+		divisor = DIV_ROUND_UP(base_clk4, i2c_bus->bus_frequency);
+		inc = 0;
+		while ((divisor + inc) > 32) {
+			inc |= divisor & 0x1;
+			divisor >>= 1;
+			baseclk_idx++;
+		}
+		divisor += inc;
+	}
+	divisor = min_t(int, divisor, 32);
+	baseclk_idx &= 0xf;
+	scl_low = ((divisor * 9) / 16) - 1;
+	scl_low = min_t(u32, scl_low, 0xf);
+	scl_high = (divisor - scl_low - 2) & 0xf;
+	/* Divisor : Base Clock : tCKHighMin : tCK High : tCK Low  */
+	data = ((scl_high - 1) << 20) | (scl_high << 16) | (scl_low << 12) | (baseclk_idx);
+	if (i2c_bus->timeout) {
+		data |= AST2600_I2CC_TOUTBASECLK(AST_I2C_TIMEOUT_CLK);
+		data |= AST2600_I2CC_TTIMEOUT(i2c_bus->timeout);
+	}
+
+	return data;
+}
+
+static u8 ast2600_i2c_recover_bus(struct ast2600_i2c_bus *i2c_bus)
+{
+	int ret = 0;
+	u32 ctrl;
+	u32 state;
+	int r;
+
+	dev_dbg(i2c_bus->dev, "%d-bus recovery bus [%x]\n", i2c_bus->adap.nr,
+		readl(i2c_bus->reg_base + AST2600_I2CC_STS_AND_BUFF));
+
+	ctrl = readl(i2c_bus->reg_base + AST2600_I2CC_FUN_CTRL);
+
+	writel(ctrl & ~(AST2600_I2CC_MASTER_EN | AST2600_I2CC_SLAVE_EN),
+	       i2c_bus->reg_base + AST2600_I2CC_FUN_CTRL);
+
+	writel(readl(i2c_bus->reg_base + AST2600_I2CC_FUN_CTRL) | AST2600_I2CC_MASTER_EN,
+	       i2c_bus->reg_base + AST2600_I2CC_FUN_CTRL);
+
+	reinit_completion(&i2c_bus->cmd_complete);
+	i2c_bus->cmd_err = 0;
+
+	/* Check 0x14's SDA and SCL status */
+	state = readl(i2c_bus->reg_base + AST2600_I2CC_STS_AND_BUFF);
+	if (!(state & AST2600_I2CC_SDA_LINE_STS) && (state & AST2600_I2CC_SCL_LINE_STS)) {
+		writel(AST2600_I2CM_RECOVER_CMD_EN, i2c_bus->reg_base + AST2600_I2CM_CMD_STS);
+		r = wait_for_completion_timeout(&i2c_bus->cmd_complete, i2c_bus->adap.timeout);
+		if (r == 0) {
+			dev_dbg(i2c_bus->dev, "recovery timed out\n");
+			ret = -ETIMEDOUT;
+		} else {
+			if (i2c_bus->cmd_err) {
+				dev_dbg(i2c_bus->dev, "recovery error\n");
+				ret = -EPROTO;
+			}
+		}
+	}
+
+	dev_dbg(i2c_bus->dev, "Recovery done [%x]\n",
+		readl(i2c_bus->reg_base + AST2600_I2CC_STS_AND_BUFF));
+	if (readl(i2c_bus->reg_base + AST2600_I2CC_STS_AND_BUFF) & AST2600_I2CC_BUS_BUSY_STS) {
+		dev_dbg(i2c_bus->dev, "Can't recovery bus [%x]\n",
+			readl(i2c_bus->reg_base + AST2600_I2CC_STS_AND_BUFF));
+		ret = -EPROTO;
+	}
+
+	writel(ctrl, i2c_bus->reg_base + AST2600_I2CC_FUN_CTRL);
+	return ret;
+}
+
+#ifdef CONFIG_I2C_SLAVE
+static void ast2600_i2c_slave_packet_dma_irq(struct ast2600_i2c_bus *i2c_bus, u32 sts)
+{
+	int slave_rx_len;
+	u32 cmd = 0;
+	u8 value;
+	int i = 0;
+
+	sts &= ~(AST2600_I2CS_SLAVE_PENDING);
+	/* Handle i2c slave timeout condition */
+	if (AST2600_I2CS_INACTIVE_TO & sts) {
+		cmd = SLAVE_TRIGGER_CMD;
+		cmd |= AST2600_I2CS_RX_DMA_EN;
+		writel(AST2600_I2CS_SET_RX_DMA_LEN(I2C_SLAVE_MSG_BUF_SIZE),
+		       i2c_bus->reg_base + AST2600_I2CS_DMA_LEN);
+		writel(cmd, i2c_bus->reg_base + AST2600_I2CS_CMD_STS);
+		writel(AST2600_I2CS_PKT_DONE, i2c_bus->reg_base + AST2600_I2CS_ISR);
+		i2c_slave_event(i2c_bus->slave, I2C_SLAVE_STOP, &value);
+		return;
+	}
+
+	sts &= ~(AST2600_I2CS_PKT_DONE | AST2600_I2CS_PKT_ERROR);
+
+	switch (sts) {
+	case AST2600_I2CS_SLAVE_MATCH | AST2600_I2CS_RX_DONE | AST2600_I2CS_WAIT_RX_DMA:
+	case AST2600_I2CS_SLAVE_MATCH | AST2600_I2CS_WAIT_RX_DMA:
+		i2c_slave_event(i2c_bus->slave, I2C_SLAVE_WRITE_REQUESTED, &value);
+		slave_rx_len = AST2600_I2C_GET_RX_DMA_LEN(readl(i2c_bus->reg_base +
+						      AST2600_I2CS_DMA_LEN_STS));
+		for (i = 0; i < slave_rx_len; i++) {
+			i2c_slave_event(i2c_bus->slave, I2C_SLAVE_WRITE_RECEIVED,
+					&i2c_bus->slave_dma_buf[i]);
+		}
+		writel(AST2600_I2CS_SET_RX_DMA_LEN(I2C_SLAVE_MSG_BUF_SIZE),
+				i2c_bus->reg_base + AST2600_I2CS_DMA_LEN);
+		cmd = SLAVE_TRIGGER_CMD | AST2600_I2CS_RX_DMA_EN;
+		break;
+	case AST2600_I2CS_SLAVE_MATCH | AST2600_I2CS_STOP:
+		i2c_slave_event(i2c_bus->slave, I2C_SLAVE_STOP, &value);
+		writel(AST2600_I2CS_SET_RX_DMA_LEN(I2C_SLAVE_MSG_BUF_SIZE),
+				i2c_bus->reg_base + AST2600_I2CS_DMA_LEN);
+		cmd = SLAVE_TRIGGER_CMD | AST2600_I2CS_RX_DMA_EN;
+		break;
+	case AST2600_I2CS_SLAVE_MATCH | AST2600_I2CS_RX_DONE_NAK |
+			AST2600_I2CS_RX_DONE | AST2600_I2CS_STOP:
+	case AST2600_I2CS_SLAVE_MATCH | AST2600_I2CS_WAIT_RX_DMA |
+			AST2600_I2CS_RX_DONE | AST2600_I2CS_STOP:
+	case AST2600_I2CS_RX_DONE_NAK | AST2600_I2CS_RX_DONE | AST2600_I2CS_STOP:
+	case AST2600_I2CS_RX_DONE | AST2600_I2CS_WAIT_RX_DMA | AST2600_I2CS_STOP:
+	case AST2600_I2CS_RX_DONE | AST2600_I2CS_STOP:
+	case AST2600_I2CS_RX_DONE | AST2600_I2CS_WAIT_RX_DMA:
+	case AST2600_I2CS_SLAVE_MATCH | AST2600_I2CS_RX_DONE | AST2600_I2CS_STOP:
+		if (sts & AST2600_I2CS_SLAVE_MATCH)
+			i2c_slave_event(i2c_bus->slave, I2C_SLAVE_WRITE_REQUESTED, &value);
+
+		slave_rx_len = AST2600_I2C_GET_RX_DMA_LEN(readl(i2c_bus->reg_base +
+						      AST2600_I2CS_DMA_LEN_STS));
+		for (i = 0; i < slave_rx_len; i++) {
+			i2c_slave_event(i2c_bus->slave, I2C_SLAVE_WRITE_RECEIVED,
+					&i2c_bus->slave_dma_buf[i]);
+		}
+		writel(AST2600_I2CS_SET_RX_DMA_LEN(I2C_SLAVE_MSG_BUF_SIZE),
+		       i2c_bus->reg_base + AST2600_I2CS_DMA_LEN);
+		if (sts & AST2600_I2CS_STOP)
+			i2c_slave_event(i2c_bus->slave, I2C_SLAVE_STOP, &value);
+		cmd = SLAVE_TRIGGER_CMD | AST2600_I2CS_RX_DMA_EN;
+		break;
+
+	/* it is Mw data Mr coming -> it need send tx */
+	case AST2600_I2CS_RX_DONE | AST2600_I2CS_WAIT_TX_DMA:
+	case AST2600_I2CS_SLAVE_MATCH | AST2600_I2CS_RX_DONE | AST2600_I2CS_WAIT_TX_DMA:
+		/* it should be repeat start read */
+		if (sts & AST2600_I2CS_SLAVE_MATCH)
+			i2c_slave_event(i2c_bus->slave, I2C_SLAVE_WRITE_REQUESTED, &value);
+
+		slave_rx_len = AST2600_I2C_GET_RX_DMA_LEN(readl(i2c_bus->reg_base +
+						      AST2600_I2CS_DMA_LEN_STS));
+		for (i = 0; i < slave_rx_len; i++) {
+			i2c_slave_event(i2c_bus->slave, I2C_SLAVE_WRITE_RECEIVED,
+					&i2c_bus->slave_dma_buf[i]);
+		}
+		i2c_slave_event(i2c_bus->slave, I2C_SLAVE_READ_REQUESTED,
+				&i2c_bus->slave_dma_buf[0]);
+		writel(0, i2c_bus->reg_base + AST2600_I2CS_DMA_LEN_STS);
+		writel(AST2600_I2CS_SET_TX_DMA_LEN(1),
+				i2c_bus->reg_base + AST2600_I2CS_DMA_LEN);
+		cmd = SLAVE_TRIGGER_CMD | AST2600_I2CS_TX_DMA_EN;
+		break;
+	case AST2600_I2CS_SLAVE_MATCH | AST2600_I2CS_WAIT_TX_DMA:
+		/* First Start read */
+		i2c_slave_event(i2c_bus->slave, I2C_SLAVE_READ_REQUESTED,
+				&i2c_bus->slave_dma_buf[0]);
+		writel(AST2600_I2CS_SET_TX_DMA_LEN(1),
+				i2c_bus->reg_base + AST2600_I2CS_DMA_LEN);
+		cmd = SLAVE_TRIGGER_CMD | AST2600_I2CS_TX_DMA_EN;
+		break;
+	case AST2600_I2CS_WAIT_TX_DMA:
+		/* it should be next start read */
+		i2c_slave_event(i2c_bus->slave, I2C_SLAVE_READ_PROCESSED,
+				&i2c_bus->slave_dma_buf[0]);
+		writel(0, i2c_bus->reg_base + AST2600_I2CS_DMA_LEN_STS);
+		writel(AST2600_I2CS_SET_TX_DMA_LEN(1),
+				i2c_bus->reg_base + AST2600_I2CS_DMA_LEN);
+		cmd = SLAVE_TRIGGER_CMD | AST2600_I2CS_TX_DMA_EN;
+		break;
+
+	case AST2600_I2CS_TX_NAK | AST2600_I2CS_STOP:
+		/* it just tx complete */
+		i2c_slave_event(i2c_bus->slave, I2C_SLAVE_STOP, &value);
+		writel(0, i2c_bus->reg_base + AST2600_I2CS_DMA_LEN_STS);
+		writel(AST2600_I2CS_SET_RX_DMA_LEN(I2C_SLAVE_MSG_BUF_SIZE),
+		       i2c_bus->reg_base + AST2600_I2CS_DMA_LEN);
+		cmd = SLAVE_TRIGGER_CMD | AST2600_I2CS_RX_DMA_EN;
+		break;
+	case AST2600_I2CS_SLAVE_MATCH | AST2600_I2CS_RX_DONE:
+		cmd = 0;
+		i2c_slave_event(i2c_bus->slave, I2C_SLAVE_WRITE_REQUESTED, &value);
+		break;
+	case AST2600_I2CS_STOP:
+		cmd = 0;
+		i2c_slave_event(i2c_bus->slave, I2C_SLAVE_STOP, &value);
+		break;
+	default:
+		dev_dbg(i2c_bus->dev, "unhandled slave isr case %x, sts %x\n", sts,
+			readl(i2c_bus->reg_base + AST2600_I2CC_STS_AND_BUFF));
+		break;
+	}
+
+	if (cmd)
+		writel(cmd, i2c_bus->reg_base + AST2600_I2CS_CMD_STS);
+	writel(AST2600_I2CS_PKT_DONE, i2c_bus->reg_base + AST2600_I2CS_ISR);
+	readl(i2c_bus->reg_base + AST2600_I2CS_ISR);
+}
+
+static void ast2600_i2c_slave_packet_buff_irq(struct ast2600_i2c_bus *i2c_bus, u32 sts)
+{
+	int slave_rx_len = 0;
+	u32 cmd = 0;
+	u8 value;
+	int i = 0;
+
+	/* due to master slave is common buffer, so need force the master stop not issue */
+	if (readl(i2c_bus->reg_base + AST2600_I2CM_CMD_STS) & 0xffff) {
+		writel(0, i2c_bus->reg_base + AST2600_I2CM_CMD_STS);
+		i2c_bus->cmd_err = -EBUSY;
+		writel(0, i2c_bus->reg_base + AST2600_I2CC_BUFF_CTRL);
+		complete(&i2c_bus->cmd_complete);
+	}
+
+	/* Handle i2c slave timeout condition */
+	if (AST2600_I2CS_INACTIVE_TO & sts) {
+		writel(SLAVE_TRIGGER_CMD, i2c_bus->reg_base + AST2600_I2CS_CMD_STS);
+		writel(AST2600_I2CS_PKT_DONE, i2c_bus->reg_base + AST2600_I2CS_ISR);
+		i2c_slave_event(i2c_bus->slave, I2C_SLAVE_STOP, &value);
+		i2c_bus->slave_operate = 0;
+		return;
+	}
+
+	sts &= ~(AST2600_I2CS_PKT_DONE | AST2600_I2CS_PKT_ERROR);
+
+	if (sts & AST2600_I2CS_SLAVE_MATCH)
+		i2c_bus->slave_operate = 1;
+
+	switch (sts) {
+	case AST2600_I2CS_SLAVE_PENDING | AST2600_I2CS_WAIT_RX_DMA |
+		 AST2600_I2CS_SLAVE_MATCH | AST2600_I2CS_RX_DONE | AST2600_I2CS_STOP:
+	case AST2600_I2CS_SLAVE_PENDING |
+		 AST2600_I2CS_SLAVE_MATCH | AST2600_I2CS_RX_DONE | AST2600_I2CS_STOP:
+	case AST2600_I2CS_SLAVE_PENDING |
+		 AST2600_I2CS_SLAVE_MATCH | AST2600_I2CS_STOP:
+		i2c_slave_event(i2c_bus->slave, I2C_SLAVE_STOP, &value);
+		fallthrough;
+	case AST2600_I2CS_SLAVE_PENDING |
+		 AST2600_I2CS_WAIT_RX_DMA | AST2600_I2CS_SLAVE_MATCH | AST2600_I2CS_RX_DONE:
+	case AST2600_I2CS_WAIT_RX_DMA | AST2600_I2CS_SLAVE_MATCH | AST2600_I2CS_RX_DONE:
+	case AST2600_I2CS_WAIT_RX_DMA | AST2600_I2CS_SLAVE_MATCH:
+		i2c_slave_event(i2c_bus->slave, I2C_SLAVE_WRITE_REQUESTED, &value);
+		cmd = SLAVE_TRIGGER_CMD;
+		if (sts & AST2600_I2CS_RX_DONE) {
+			slave_rx_len = AST2600_I2CC_GET_RX_BUF_LEN(readl(i2c_bus->reg_base +
+							       AST2600_I2CC_BUFF_CTRL));
+			for (i = 0; i < slave_rx_len; i++) {
+				value = readb(i2c_bus->buf_base + 0x10 + i);
+				i2c_slave_event(i2c_bus->slave, I2C_SLAVE_WRITE_RECEIVED, &value);
+			}
+		}
+		if (readl(i2c_bus->reg_base + AST2600_I2CS_CMD_STS) & AST2600_I2CS_RX_BUFF_EN)
+			cmd = 0;
+		else
+			cmd = SLAVE_TRIGGER_CMD | AST2600_I2CS_RX_BUFF_EN;
+
+		writel(AST2600_I2CC_SET_RX_BUF_LEN(i2c_bus->buf_size),
+					i2c_bus->reg_base + AST2600_I2CC_BUFF_CTRL);
+		break;
+	case AST2600_I2CS_WAIT_RX_DMA | AST2600_I2CS_RX_DONE:
+		cmd = SLAVE_TRIGGER_CMD;
+		slave_rx_len = AST2600_I2CC_GET_RX_BUF_LEN(readl(i2c_bus->reg_base +
+						       AST2600_I2CC_BUFF_CTRL));
+		for (i = 0; i < slave_rx_len; i++) {
+			value = readb(i2c_bus->buf_base + 0x10 + i);
+			i2c_slave_event(i2c_bus->slave, I2C_SLAVE_WRITE_RECEIVED, &value);
+		}
+		cmd |= AST2600_I2CS_RX_BUFF_EN;
+		writel(AST2600_I2CC_SET_RX_BUF_LEN(i2c_bus->buf_size),
+						i2c_bus->reg_base + AST2600_I2CC_BUFF_CTRL);
+		break;
+	case AST2600_I2CS_SLAVE_PENDING | AST2600_I2CS_WAIT_RX_DMA |
+				AST2600_I2CS_RX_DONE | AST2600_I2CS_STOP:
+		cmd = SLAVE_TRIGGER_CMD;
+		slave_rx_len = AST2600_I2CC_GET_RX_BUF_LEN(readl(i2c_bus->reg_base +
+						       AST2600_I2CC_BUFF_CTRL));
+		for (i = 0; i < slave_rx_len; i++) {
+			value = readb(i2c_bus->buf_base + 0x10 + i);
+			i2c_slave_event(i2c_bus->slave, I2C_SLAVE_WRITE_RECEIVED, &value);
+		}
+		i2c_slave_event(i2c_bus->slave, I2C_SLAVE_STOP, &value);
+		cmd |= AST2600_I2CS_RX_BUFF_EN;
+		writel(AST2600_I2CC_SET_RX_BUF_LEN(i2c_bus->buf_size),
+						i2c_bus->reg_base + AST2600_I2CC_BUFF_CTRL);
+		break;
+
+	case AST2600_I2CS_SLAVE_PENDING | AST2600_I2CS_RX_DONE | AST2600_I2CS_STOP:
+		cmd = SLAVE_TRIGGER_CMD;
+		slave_rx_len = AST2600_I2CC_GET_RX_BUF_LEN(readl(i2c_bus->reg_base +
+							   AST2600_I2CC_BUFF_CTRL));
+		for (i = 0; i < slave_rx_len; i++) {
+			value = readb(i2c_bus->buf_base + 0x10 + i);
+			i2c_slave_event(i2c_bus->slave, I2C_SLAVE_WRITE_RECEIVED, &value);
+		}
+		/* workaround for avoid next start with len != 0 */
+		writel(BIT(0), i2c_bus->reg_base + AST2600_I2CC_BUFF_CTRL);
+		i2c_slave_event(i2c_bus->slave, I2C_SLAVE_STOP, &value);
+		break;
+
+	case AST2600_I2CS_RX_DONE | AST2600_I2CS_STOP:
+		cmd = SLAVE_TRIGGER_CMD;
+		slave_rx_len = AST2600_I2CC_GET_RX_BUF_LEN(readl(i2c_bus->reg_base +
+							   AST2600_I2CC_BUFF_CTRL));
+		for (i = 0; i < slave_rx_len; i++) {
+			value = readb(i2c_bus->buf_base + 0x10 + i);
+			i2c_slave_event(i2c_bus->slave, I2C_SLAVE_WRITE_RECEIVED, &value);
+		}
+		/* workaround for avoid next start with len != 0 */
+		writel(BIT(0), i2c_bus->reg_base + AST2600_I2CC_BUFF_CTRL);
+		i2c_slave_event(i2c_bus->slave, I2C_SLAVE_STOP, &value);
+		break;
+	case AST2600_I2CS_WAIT_TX_DMA | AST2600_I2CS_SLAVE_MATCH:
+		i2c_slave_event(i2c_bus->slave, I2C_SLAVE_READ_REQUESTED, &value);
+		writeb(value, i2c_bus->buf_base);
+		writel(AST2600_I2CC_SET_TX_BUF_LEN(1),
+				i2c_bus->reg_base + AST2600_I2CC_BUFF_CTRL);
+		cmd = SLAVE_TRIGGER_CMD | AST2600_I2CS_TX_BUFF_EN;
+		break;
+	case AST2600_I2CS_WAIT_TX_DMA | AST2600_I2CS_RX_DONE:
+	case AST2600_I2CS_WAIT_TX_DMA:
+		if (sts & AST2600_I2CS_RX_DONE) {
+			slave_rx_len = AST2600_I2CC_GET_RX_BUF_LEN(readl(i2c_bus->reg_base +
+							AST2600_I2CC_BUFF_CTRL));
+			for (i = 0; i < slave_rx_len; i++) {
+				value = readb(i2c_bus->buf_base + 0x10 + i);
+				i2c_slave_event(i2c_bus->slave, I2C_SLAVE_WRITE_RECEIVED, &value);
+			}
+			i2c_slave_event(i2c_bus->slave, I2C_SLAVE_READ_REQUESTED, &value);
+		} else {
+			i2c_slave_event(i2c_bus->slave, I2C_SLAVE_READ_PROCESSED, &value);
+		}
+		writeb(value, i2c_bus->buf_base);
+		writel(AST2600_I2CC_SET_TX_BUF_LEN(1),
+				i2c_bus->reg_base + AST2600_I2CC_BUFF_CTRL);
+		cmd = SLAVE_TRIGGER_CMD | AST2600_I2CS_TX_BUFF_EN;
+		break;
+	/* workaround : trigger the cmd twice to fix next state keep 1000000 */
+	case AST2600_I2CS_SLAVE_MATCH | AST2600_I2CS_RX_DONE:
+		i2c_slave_event(i2c_bus->slave, I2C_SLAVE_WRITE_REQUESTED, &value);
+		cmd = SLAVE_TRIGGER_CMD | AST2600_I2CS_RX_BUFF_EN;
+		writel(cmd, i2c_bus->reg_base + AST2600_I2CS_CMD_STS);
+		break;
+
+	case AST2600_I2CS_TX_NAK | AST2600_I2CS_STOP:
+	case AST2600_I2CS_STOP:
+		cmd = SLAVE_TRIGGER_CMD;
+		i2c_slave_event(i2c_bus->slave, I2C_SLAVE_STOP, &value);
+		break;
+	default:
+		dev_dbg(i2c_bus->dev, "unhandled slave isr case %x, sts %x\n", sts,
+			readl(i2c_bus->reg_base + AST2600_I2CC_STS_AND_BUFF));
+		break;
+	}
+
+	if (cmd)
+		writel(cmd, i2c_bus->reg_base + AST2600_I2CS_CMD_STS);
+	writel(AST2600_I2CS_PKT_DONE, i2c_bus->reg_base + AST2600_I2CS_ISR);
+	readl(i2c_bus->reg_base + AST2600_I2CS_ISR);
+
+	if ((sts & AST2600_I2CS_STOP) && !(sts & AST2600_I2CS_SLAVE_PENDING))
+		i2c_bus->slave_operate = 0;
+
+}
+
+static void ast2600_i2c_slave_byte_irq(struct ast2600_i2c_bus *i2c_bus, u32 sts)
+{
+	u32 i2c_buff = readl(i2c_bus->reg_base + AST2600_I2CC_STS_AND_BUFF);
+	u32 cmd = AST2600_I2CS_ACTIVE_ALL;
+	u8 byte_data;
+	u8 value;
+
+	switch (sts) {
+	case AST2600_I2CS_SLAVE_MATCH | AST2600_I2CS_RX_DONE | AST2600_I2CS_WAIT_RX_DMA:
+		i2c_slave_event(i2c_bus->slave, I2C_SLAVE_WRITE_REQUESTED, &value);
+		/* first address match is address */
+		byte_data = AST2600_I2CC_GET_RX_BUFF(i2c_buff);
+		break;
+	case AST2600_I2CS_RX_DONE | AST2600_I2CS_WAIT_RX_DMA:
+		byte_data = AST2600_I2CC_GET_RX_BUFF(i2c_buff);
+		i2c_slave_event(i2c_bus->slave, I2C_SLAVE_WRITE_RECEIVED, &byte_data);
+		break;
+	case AST2600_I2CS_SLAVE_MATCH | AST2600_I2CS_RX_DONE | AST2600_I2CS_WAIT_TX_DMA:
+		cmd |= AST2600_I2CS_TX_CMD;
+		byte_data = AST2600_I2CC_GET_RX_BUFF(i2c_buff);
+		i2c_slave_event(i2c_bus->slave, I2C_SLAVE_READ_REQUESTED, &byte_data);
+		writel(byte_data, i2c_bus->reg_base + AST2600_I2CC_STS_AND_BUFF);
+		break;
+	case AST2600_I2CS_TX_ACK | AST2600_I2CS_WAIT_TX_DMA:
+		cmd |= AST2600_I2CS_TX_CMD;
+		i2c_slave_event(i2c_bus->slave, I2C_SLAVE_READ_PROCESSED, &byte_data);
+		writel(byte_data, i2c_bus->reg_base + AST2600_I2CC_STS_AND_BUFF);
+		break;
+	case AST2600_I2CS_STOP:
+	case AST2600_I2CS_STOP | AST2600_I2CS_TX_NAK:
+		i2c_slave_event(i2c_bus->slave, I2C_SLAVE_STOP, &value);
+		break;
+	default:
+		dev_dbg(i2c_bus->dev, "unhandled pkt isr %x\n", sts);
+		break;
+	}
+	writel(cmd, i2c_bus->reg_base + AST2600_I2CS_CMD_STS);
+	writel(sts, i2c_bus->reg_base + AST2600_I2CS_ISR);
+	readl(i2c_bus->reg_base + AST2600_I2CS_ISR);
+}
+
+static int ast2600_i2c_slave_irq(struct ast2600_i2c_bus *i2c_bus)
+{
+	u32 ier = readl(i2c_bus->reg_base + AST2600_I2CS_IER);
+	u32 isr = readl(i2c_bus->reg_base + AST2600_I2CS_ISR);
+
+	if (!(isr & ier))
+		return 0;
+
+	/* Slave interrupt coming after Master package done
+	 * So need handle master first.
+	 */
+	if (readl(i2c_bus->reg_base + AST2600_I2CM_ISR) & AST2600_I2CM_PKT_DONE)
+		return 0;
+
+	isr &= ~(AST2600_I2CS_ADDR_INDICATE_MASK);
+
+	if (AST2600_I2CS_ADDR1_NAK & isr)
+		isr &= ~AST2600_I2CS_ADDR1_NAK;
+
+	if (AST2600_I2CS_ADDR2_NAK & isr)
+		isr &= ~AST2600_I2CS_ADDR2_NAK;
+
+	if (AST2600_I2CS_ADDR3_NAK & isr)
+		isr &= ~AST2600_I2CS_ADDR3_NAK;
+
+	if (AST2600_I2CS_ADDR_MASK & isr)
+		isr &= ~AST2600_I2CS_ADDR_MASK;
+
+	if (AST2600_I2CS_PKT_DONE & isr) {
+		if (i2c_bus->mode == DMA_MODE)
+			ast2600_i2c_slave_packet_dma_irq(i2c_bus, isr);
+		else
+			ast2600_i2c_slave_packet_buff_irq(i2c_bus, isr);
+	} else
+		ast2600_i2c_slave_byte_irq(i2c_bus, isr);
+
+	return 1;
+}
+#endif
+
+static int ast2600_i2c_do_start(struct ast2600_i2c_bus *i2c_bus)
+{
+	struct i2c_msg *msg = &i2c_bus->msgs[i2c_bus->msgs_index];
+	int xfer_len = 0;
+	int i = 0;
+	u32 cmd;
+
+	cmd = AST2600_I2CM_PKT_EN | AST2600_I2CM_PKT_ADDR(msg->addr) | AST2600_I2CM_START_CMD;
+
+	/* send start */
+	dev_dbg(i2c_bus->dev, "[%d] %sing %d byte%s %s 0x%02x\n",
+		i2c_bus->msgs_index, msg->flags & I2C_M_RD ? "read" : "write",
+		msg->len, msg->len > 1 ? "s" : "",
+		msg->flags & I2C_M_RD ? "from" : "to", msg->addr);
+
+	i2c_bus->master_xfer_cnt = 0;
+	i2c_bus->buf_index = 0;
+
+	if (msg->flags & I2C_M_RD) {
+		cmd |= AST2600_I2CM_RX_CMD;
+		if (i2c_bus->mode == DMA_MODE) {
+			/* dma mode */
+			cmd |= AST2600_I2CM_RX_DMA_EN;
+
+			if (msg->flags & I2C_M_RECV_LEN) {
+				xfer_len = 1;
+			} else {
+				if (msg->len > AST2600_I2C_DMA_SIZE) {
+					xfer_len = AST2600_I2C_DMA_SIZE;
+				} else {
+					xfer_len = msg->len;
+					if (i2c_bus->msgs_index + 1 == i2c_bus->msgs_count)
+						cmd |= MASTER_TRIGGER_LAST_STOP;
+				}
+			}
+			writel(AST2600_I2CM_SET_RX_DMA_LEN(xfer_len - 1),
+			       i2c_bus->reg_base + AST2600_I2CM_DMA_LEN);
+			i2c_bus->master_safe_buf = i2c_get_dma_safe_msg_buf(msg, 1);
+			if (!i2c_bus->master_safe_buf)
+				return -ENOMEM;
+			i2c_bus->master_dma_addr =
+				dma_map_single(i2c_bus->dev, i2c_bus->master_safe_buf,
+								msg->len, DMA_FROM_DEVICE);
+			if (dma_mapping_error(i2c_bus->dev, i2c_bus->master_dma_addr)) {
+				i2c_put_dma_safe_msg_buf(i2c_bus->master_safe_buf, msg, false);
+				i2c_bus->master_safe_buf = NULL;
+				return -ENOMEM;
+			}
+			writel(i2c_bus->master_dma_addr, i2c_bus->reg_base + AST2600_I2CM_RX_DMA);
+		} else if (i2c_bus->mode == BUFF_MODE) {
+			/* buff mode */
+			cmd |= AST2600_I2CM_RX_BUFF_EN;
+			if (msg->flags & I2C_M_RECV_LEN) {
+				dev_dbg(i2c_bus->dev, "smbus read\n");
+				xfer_len = 1;
+			} else {
+				if (msg->len > i2c_bus->buf_size) {
+					xfer_len = i2c_bus->buf_size;
+				} else {
+					xfer_len = msg->len;
+					if (i2c_bus->msgs_index + 1 == i2c_bus->msgs_count)
+						cmd |= MASTER_TRIGGER_LAST_STOP;
+				}
+			}
+			writel(AST2600_I2CC_SET_RX_BUF_LEN(xfer_len),
+			       i2c_bus->reg_base + AST2600_I2CC_BUFF_CTRL);
+		} else {
+			/* byte mode */
+			xfer_len = 1;
+			if (msg->flags & I2C_M_RECV_LEN) {
+				dev_dbg(i2c_bus->dev, "smbus read\n");
+			} else {
+				if (i2c_bus->msgs_index + 1 == i2c_bus->msgs_count) {
+					if (msg->len == 1)
+						cmd |= MASTER_TRIGGER_LAST_STOP;
+				}
+			}
+		}
+	} else {
+		if (i2c_bus->mode == DMA_MODE) {
+			/* dma mode */
+			if (msg->len > AST2600_I2C_DMA_SIZE) {
+				xfer_len = AST2600_I2C_DMA_SIZE;
+			} else {
+				if (i2c_bus->msgs_index + 1 == i2c_bus->msgs_count)
+					cmd |= AST2600_I2CM_STOP_CMD;
+				xfer_len = msg->len;
+			}
+
+			if (xfer_len) {
+				cmd |= AST2600_I2CM_TX_DMA_EN | AST2600_I2CM_TX_CMD;
+				writel(AST2600_I2CM_SET_TX_DMA_LEN(xfer_len - 1),
+				       i2c_bus->reg_base + AST2600_I2CM_DMA_LEN);
+				i2c_bus->master_safe_buf = i2c_get_dma_safe_msg_buf(msg, 1);
+				if (!i2c_bus->master_safe_buf)
+					return -ENOMEM;
+				i2c_bus->master_dma_addr =
+					dma_map_single(i2c_bus->dev, i2c_bus->master_safe_buf,
+								msg->len, DMA_TO_DEVICE);
+				if (dma_mapping_error(i2c_bus->dev, i2c_bus->master_dma_addr)) {
+					i2c_put_dma_safe_msg_buf(i2c_bus->master_safe_buf,
+											msg, false);
+					i2c_bus->master_safe_buf = NULL;
+					return -ENOMEM;
+				}
+				writel(i2c_bus->master_dma_addr,
+				       i2c_bus->reg_base + AST2600_I2CM_TX_DMA);
+			}
+		} else if (i2c_bus->mode == BUFF_MODE) {
+			u8 wbuf[4];
+			/* buff mode */
+			if (msg->len > i2c_bus->buf_size) {
+				xfer_len = i2c_bus->buf_size;
+			} else {
+				if (i2c_bus->msgs_index + 1 == i2c_bus->msgs_count)
+					cmd |= AST2600_I2CM_STOP_CMD;
+				xfer_len = msg->len;
+			}
+			if (xfer_len) {
+				cmd |= AST2600_I2CM_TX_BUFF_EN | AST2600_I2CM_TX_CMD;
+				if (readl(i2c_bus->reg_base + AST2600_I2CS_ISR))
+					return -ENOMEM;
+				writel(AST2600_I2CC_SET_TX_BUF_LEN(xfer_len),
+				       i2c_bus->reg_base + AST2600_I2CC_BUFF_CTRL);
+				if (readl(i2c_bus->reg_base + AST2600_I2CS_ISR))
+					return -ENOMEM;
+				for (i = 0; i < xfer_len; i++) {
+					wbuf[i % 4] = msg->buf[i];
+					if (i % 4 == 3)
+						writel(*(u32 *)wbuf, i2c_bus->buf_base + i - 3);
+				}
+				if (--i % 4 != 3)
+					writel(*(u32 *)wbuf, i2c_bus->buf_base + i - (i % 4));
+			}
+			if (readl(i2c_bus->reg_base + AST2600_I2CS_ISR))
+				return -ENOMEM;
+		} else {
+			/* byte mode */
+			if ((i2c_bus->msgs_index + 1 == i2c_bus->msgs_count) && (msg->len <= 1))
+				cmd |= AST2600_I2CM_STOP_CMD;
+
+			if (msg->len) {
+				cmd |= AST2600_I2CM_TX_CMD;
+				xfer_len = 1;
+				writel(msg->buf[0], i2c_bus->reg_base + AST2600_I2CC_STS_AND_BUFF);
+			} else {
+				xfer_len = 0;
+			}
+		}
+	}
+	writel(cmd, i2c_bus->reg_base + AST2600_I2CM_CMD_STS);
+	return 0;
+}
+
+static int ast2600_i2c_is_irq_error(u32 irq_status)
+{
+	if (irq_status & AST2600_I2CM_ARBIT_LOSS)
+		return -EAGAIN;
+	if (irq_status & (AST2600_I2CM_SDA_DL_TO | AST2600_I2CM_SCL_LOW_TO))
+		return -EBUSY;
+	if (irq_status & (AST2600_I2CM_ABNORMAL))
+		return -EPROTO;
+
+	return 0;
+}
+
+static void ast2600_i2c_master_package_irq(struct ast2600_i2c_bus *i2c_bus, u32 sts)
+{
+	struct i2c_msg *msg = &i2c_bus->msgs[i2c_bus->msgs_index];
+	u32 cmd = AST2600_I2CM_PKT_EN;
+	int xfer_len;
+	int i;
+
+	sts &= ~AST2600_I2CM_PKT_DONE;
+	writel(AST2600_I2CM_PKT_DONE, i2c_bus->reg_base + AST2600_I2CM_ISR);
+	switch (sts) {
+	case AST2600_I2CM_PKT_ERROR:
+		i2c_bus->cmd_err = -EAGAIN;
+		complete(&i2c_bus->cmd_complete);
+		break;
+	case AST2600_I2CM_PKT_ERROR | AST2600_I2CM_TX_NAK: /* a0 fix for issue */
+		fallthrough;
+	case AST2600_I2CM_PKT_ERROR | AST2600_I2CM_TX_NAK | AST2600_I2CM_NORMAL_STOP:
+		i2c_bus->cmd_err = -ENXIO;
+		complete(&i2c_bus->cmd_complete);
+		break;
+	case AST2600_I2CM_NORMAL_STOP:
+		/* write 0 byte only have stop isr */
+		i2c_bus->msgs_index++;
+		if (i2c_bus->msgs_index < i2c_bus->msgs_count) {
+			if (ast2600_i2c_do_start(i2c_bus)) {
+				i2c_bus->cmd_err = -ENOMEM;
+				complete(&i2c_bus->cmd_complete);
+			}
+		} else {
+			i2c_bus->cmd_err = i2c_bus->msgs_index;
+			complete(&i2c_bus->cmd_complete);
+		}
+		break;
+	case AST2600_I2CM_TX_ACK:
+	case AST2600_I2CM_TX_ACK | AST2600_I2CM_NORMAL_STOP:
+		if (i2c_bus->mode == DMA_MODE)
+			xfer_len = AST2600_I2C_GET_TX_DMA_LEN(readl(i2c_bus->reg_base +
+							  AST2600_I2CM_DMA_LEN_STS));
+		else if (i2c_bus->mode == BUFF_MODE)
+			xfer_len = AST2600_I2CC_GET_TX_BUF_LEN(readl(i2c_bus->reg_base +
+							   AST2600_I2CC_BUFF_CTRL));
+		else
+			xfer_len = 1;
+
+		i2c_bus->master_xfer_cnt += xfer_len;
+
+		if (i2c_bus->master_xfer_cnt == msg->len) {
+			if (i2c_bus->mode == DMA_MODE) {
+				dma_unmap_single(i2c_bus->dev, i2c_bus->master_dma_addr, msg->len,
+						 DMA_TO_DEVICE);
+				i2c_put_dma_safe_msg_buf(i2c_bus->master_safe_buf, msg, true);
+				i2c_bus->master_safe_buf = NULL;
+			}
+			i2c_bus->msgs_index++;
+			if (i2c_bus->msgs_index == i2c_bus->msgs_count) {
+				i2c_bus->cmd_err = i2c_bus->msgs_index;
+				complete(&i2c_bus->cmd_complete);
+			} else {
+				if (ast2600_i2c_do_start(i2c_bus)) {
+					i2c_bus->cmd_err = -ENOMEM;
+					complete(&i2c_bus->cmd_complete);
+				}
+			}
+		} else {
+			/* do next tx */
+			cmd |= AST2600_I2CM_TX_CMD;
+			if (i2c_bus->mode == DMA_MODE) {
+				cmd |= AST2600_I2CM_TX_DMA_EN;
+				xfer_len = msg->len - i2c_bus->master_xfer_cnt;
+				if (xfer_len > AST2600_I2C_DMA_SIZE) {
+					xfer_len = AST2600_I2C_DMA_SIZE;
+				} else {
+					if (i2c_bus->msgs_index + 1 == i2c_bus->msgs_count)
+						cmd |= AST2600_I2CM_STOP_CMD;
+				}
+				writel(AST2600_I2CM_SET_TX_DMA_LEN(xfer_len - 1),
+				       i2c_bus->reg_base + AST2600_I2CM_DMA_LEN);
+				writel(i2c_bus->master_dma_addr + i2c_bus->master_xfer_cnt,
+				       i2c_bus->reg_base + AST2600_I2CM_TX_DMA);
+			} else if (i2c_bus->mode == BUFF_MODE) {
+				u8 wbuf[4];
+
+				cmd |= AST2600_I2CM_TX_BUFF_EN;
+				xfer_len = msg->len - i2c_bus->master_xfer_cnt;
+				if (xfer_len > i2c_bus->buf_size) {
+					xfer_len = i2c_bus->buf_size;
+				} else {
+					if (i2c_bus->msgs_index + 1 == i2c_bus->msgs_count)
+						cmd |= AST2600_I2CM_STOP_CMD;
+				}
+				for (i = 0; i < xfer_len; i++) {
+					wbuf[i % 4] = msg->buf[i2c_bus->master_xfer_cnt + i];
+					if (i % 4 == 3)
+						writel(*(u32 *)wbuf, i2c_bus->buf_base + i - 3);
+				}
+				if (--i % 4 != 3)
+					writel(*(u32 *)wbuf, i2c_bus->buf_base + i - (i % 4));
+				writel(AST2600_I2CC_SET_TX_BUF_LEN(xfer_len),
+				       i2c_bus->reg_base + AST2600_I2CC_BUFF_CTRL);
+			} else {
+				/* byte */
+				if ((i2c_bus->msgs_index + 1 == i2c_bus->msgs_count) &&
+				    ((i2c_bus->master_xfer_cnt + 1) == msg->len)) {
+					cmd |= AST2600_I2CM_STOP_CMD;
+				}
+				writel(msg->buf[i2c_bus->master_xfer_cnt],
+				       i2c_bus->reg_base + AST2600_I2CC_STS_AND_BUFF);
+			}
+			writel(cmd, i2c_bus->reg_base + AST2600_I2CM_CMD_STS);
+		}
+		break;
+	case AST2600_I2CM_RX_DONE:
+#ifdef CONFIG_I2C_SLAVE
+		/* Workaround for master/slave package mode enable rx done stuck issue
+		 * When master go for first read (RX_DONE), slave mode will also effect
+		 * Then controller will send nack, not operate anymore.
+		 */
+		if (readl(i2c_bus->reg_base + AST2600_I2CS_CMD_STS) & AST2600_I2CS_PKT_MODE_EN) {
+			u32 slave_cmd = readl(i2c_bus->reg_base + AST2600_I2CS_CMD_STS);
+
+			writel(0, i2c_bus->reg_base + AST2600_I2CS_CMD_STS);
+			writel(slave_cmd, i2c_bus->reg_base + AST2600_I2CS_CMD_STS);
+		}
+		fallthrough;
+#endif
+	case AST2600_I2CM_RX_DONE | AST2600_I2CM_NORMAL_STOP:
+		/* do next rx */
+		if (i2c_bus->mode == DMA_MODE) {
+			xfer_len = AST2600_I2C_GET_RX_DMA_LEN(readl(i2c_bus->reg_base +
+							  AST2600_I2CM_DMA_LEN_STS));
+		} else if (i2c_bus->mode == BUFF_MODE) {
+			xfer_len = AST2600_I2CC_GET_RX_BUF_LEN(
+						readl(i2c_bus->reg_base + AST2600_I2CC_BUFF_CTRL));
+			for (i = 0; i < xfer_len; i++)
+				msg->buf[i2c_bus->master_xfer_cnt + i] =
+					readb(i2c_bus->buf_base + 0x10 + i);
+		} else {
+			xfer_len = 1;
+			msg->buf[i2c_bus->master_xfer_cnt] =
+				AST2600_I2CC_GET_RX_BUFF(readl(i2c_bus->reg_base +
+						     AST2600_I2CC_STS_AND_BUFF));
+		}
+
+		if (msg->flags & I2C_M_RECV_LEN) {
+			msg->len = msg->buf[0] + ((msg->flags & I2C_CLIENT_PEC) ? 2 : 1);
+			msg->len = min_t(unsigned int, msg->len, I2C_SMBUS_BLOCK_MAX);
+			msg->flags &= ~I2C_M_RECV_LEN;
+		}
+		i2c_bus->master_xfer_cnt += xfer_len;
+
+		if (i2c_bus->master_xfer_cnt == msg->len) {
+			if (i2c_bus->mode == DMA_MODE) {
+				dma_unmap_single(i2c_bus->dev, i2c_bus->master_dma_addr, msg->len,
+						 DMA_FROM_DEVICE);
+				i2c_put_dma_safe_msg_buf(i2c_bus->master_safe_buf, msg, true);
+				i2c_bus->master_safe_buf = NULL;
+			}
+
+			i2c_bus->msgs_index++;
+			if (i2c_bus->msgs_index == i2c_bus->msgs_count) {
+				i2c_bus->cmd_err = i2c_bus->msgs_index;
+				complete(&i2c_bus->cmd_complete);
+			} else {
+				if (ast2600_i2c_do_start(i2c_bus)) {
+					i2c_bus->cmd_err = -ENOMEM;
+					complete(&i2c_bus->cmd_complete);
+				}
+			}
+		} else {
+			/* next rx */
+			cmd |= AST2600_I2CM_RX_CMD;
+			if (i2c_bus->mode == DMA_MODE) {
+				cmd |= AST2600_I2CM_RX_DMA_EN;
+				xfer_len = msg->len - i2c_bus->master_xfer_cnt;
+				if (xfer_len > AST2600_I2C_DMA_SIZE) {
+					xfer_len = AST2600_I2C_DMA_SIZE;
+				} else {
+					if (i2c_bus->msgs_index + 1 == i2c_bus->msgs_count)
+						cmd |= MASTER_TRIGGER_LAST_STOP;
+				}
+				writel(AST2600_I2CM_SET_RX_DMA_LEN(xfer_len - 1),
+				       i2c_bus->reg_base + AST2600_I2CM_DMA_LEN);
+				writel(i2c_bus->master_dma_addr + i2c_bus->master_xfer_cnt,
+				       i2c_bus->reg_base + AST2600_I2CM_RX_DMA);
+			} else if (i2c_bus->mode == BUFF_MODE) {
+				cmd |= AST2600_I2CM_RX_BUFF_EN;
+				xfer_len = msg->len - i2c_bus->master_xfer_cnt;
+				if (xfer_len > i2c_bus->buf_size)
+					xfer_len = i2c_bus->buf_size;
+				else {
+					if (i2c_bus->msgs_index + 1 == i2c_bus->msgs_count)
+						cmd |= MASTER_TRIGGER_LAST_STOP;
+				}
+				writel(AST2600_I2CC_SET_RX_BUF_LEN(xfer_len),
+				       i2c_bus->reg_base + AST2600_I2CC_BUFF_CTRL);
+			} else {
+				if ((i2c_bus->msgs_index + 1 == i2c_bus->msgs_count) &&
+				    ((i2c_bus->master_xfer_cnt + 1) == msg->len)) {
+					cmd |= MASTER_TRIGGER_LAST_STOP;
+				}
+			}
+			writel(cmd, i2c_bus->reg_base + AST2600_I2CM_CMD_STS);
+		}
+		break;
+	default:
+		dev_dbg(i2c_bus->dev, "unhandled sts %x\n", sts);
+		break;
+	}
+}
+
+static int ast2600_i2c_master_irq(struct ast2600_i2c_bus *i2c_bus)
+{
+	u32 sts = readl(i2c_bus->reg_base + AST2600_I2CM_ISR);
+	u32 ier = readl(i2c_bus->reg_base + AST2600_I2CM_IER);
+	u32 ctrl = 0;
+
+	if (!i2c_bus->alert_enable)
+		sts &= ~AST2600_I2CM_SMBUS_ALT;
+
+	if (AST2600_I2CM_BUS_RECOVER_FAIL & sts) {
+		writel(AST2600_I2CM_BUS_RECOVER_FAIL, i2c_bus->reg_base + AST2600_I2CM_ISR);
+		ctrl = readl(i2c_bus->reg_base + AST2600_I2CC_FUN_CTRL);
+		writel(0, i2c_bus->reg_base + AST2600_I2CC_FUN_CTRL);
+		writel(ctrl, i2c_bus->reg_base + AST2600_I2CC_FUN_CTRL);
+		i2c_bus->cmd_err = -EPROTO;
+		complete(&i2c_bus->cmd_complete);
+		return 1;
+	}
+
+	if (AST2600_I2CM_BUS_RECOVER & sts) {
+		writel(AST2600_I2CM_BUS_RECOVER, i2c_bus->reg_base + AST2600_I2CM_ISR);
+		i2c_bus->cmd_err = 0;
+		complete(&i2c_bus->cmd_complete);
+		return 1;
+	}
+
+	if (AST2600_I2CM_SMBUS_ALT & sts) {
+		if (ier & AST2600_I2CM_SMBUS_ALT) {
+			/* Disable ALT INT */
+			writel(ier & ~AST2600_I2CM_SMBUS_ALT, i2c_bus->reg_base + AST2600_I2CM_IER);
+			i2c_handle_smbus_alert(i2c_bus->ara);
+			writel(AST2600_I2CM_SMBUS_ALT, i2c_bus->reg_base + AST2600_I2CM_ISR);
+			dev_err(i2c_bus->dev,
+				"ast2600_master_alert_recv bus id %d, Disable Alt, Please Imple\n",
+				i2c_bus->adap.nr);
+			return 1;
+		}
+	}
+
+	i2c_bus->cmd_err = ast2600_i2c_is_irq_error(sts);
+	if (i2c_bus->cmd_err) {
+		writel(AST2600_I2CM_PKT_DONE, i2c_bus->reg_base + AST2600_I2CM_ISR);
+		complete(&i2c_bus->cmd_complete);
+		return 1;
+	}
+
+	if (AST2600_I2CM_PKT_DONE & sts) {
+		ast2600_i2c_master_package_irq(i2c_bus, sts);
+		return 1;
+	}
+
+	return 0;
+}
+
+static irqreturn_t ast2600_i2c_bus_irq(int irq, void *dev_id)
+{
+	struct ast2600_i2c_bus *i2c_bus = dev_id;
+
+#ifdef CONFIG_I2C_SLAVE
+	if (readl(i2c_bus->reg_base + AST2600_I2CC_FUN_CTRL) & AST2600_I2CC_SLAVE_EN) {
+		if (ast2600_i2c_slave_irq(i2c_bus))
+			return IRQ_HANDLED;
+	}
+#endif
+	return ast2600_i2c_master_irq(i2c_bus) ? IRQ_HANDLED : IRQ_NONE;
+}
+
+static int ast2600_i2c_master_xfer(struct i2c_adapter *adap,
+				      struct i2c_msg *msgs, int num)
+{
+	struct ast2600_i2c_bus *i2c_bus = i2c_get_adapdata(adap);
+	unsigned long timeout;
+	int ret = 0;
+
+	/* If bus is busy in a single master environment, attempt recovery. */
+	if (!i2c_bus->multi_master &&
+	    (readl(i2c_bus->reg_base + AST2600_I2CC_STS_AND_BUFF) & AST2600_I2CC_BUS_BUSY_STS)) {
+		int ret;
+
+		ret = ast2600_i2c_recover_bus(i2c_bus);
+		if (ret)
+			return ret;
+	}
+
+#ifdef CONFIG_I2C_SLAVE
+	if (i2c_bus->mode == BUFF_MODE) {
+		if (i2c_bus->slave_operate)
+			return -EBUSY;
+		/* disable slave isr */
+		writel(0, i2c_bus->reg_base + AST2600_I2CS_IER);
+		if (readl(i2c_bus->reg_base + AST2600_I2CS_ISR) || (i2c_bus->slave_operate)) {
+			writel(AST2600_I2CS_PKT_DONE, i2c_bus->reg_base + AST2600_I2CS_IER);
+			return -EBUSY;
+		}
+	}
+#endif
+
+	i2c_bus->cmd_err = 0;
+	i2c_bus->msgs = msgs;
+	i2c_bus->msgs_index = 0;
+	i2c_bus->msgs_count = num;
+	reinit_completion(&i2c_bus->cmd_complete);
+	ret = ast2600_i2c_do_start(i2c_bus);
+#ifdef CONFIG_I2C_SLAVE
+	/* avoid race condication slave is wait and master wait 1st slave operate */
+	if (i2c_bus->mode == BUFF_MODE)
+		writel(AST2600_I2CS_PKT_DONE, i2c_bus->reg_base + AST2600_I2CS_IER);
+#endif
+	if (ret)
+		goto master_out;
+	timeout = wait_for_completion_timeout(&i2c_bus->cmd_complete, i2c_bus->adap.timeout);
+	if (timeout == 0) {
+		u32 isr = readl(i2c_bus->reg_base + AST2600_I2CM_ISR);
+		u32 i2c_status = readl(i2c_bus->reg_base + AST2600_I2CC_STS_AND_BUFF);
+
+		dev_dbg(i2c_bus->dev, "timeout isr[%x], sts[%x]\n", isr, i2c_status);
+		if (isr || (i2c_status & AST2600_I2CC_TX_DIR_MASK)) {
+			u32 ctrl = readl(i2c_bus->reg_base + AST2600_I2CC_FUN_CTRL);
+
+			writel(0, i2c_bus->reg_base + AST2600_I2CC_FUN_CTRL);
+			writel(ctrl, i2c_bus->reg_base + AST2600_I2CC_FUN_CTRL);
+#ifdef CONFIG_I2C_SLAVE
+			if (ctrl & AST2600_I2CC_SLAVE_EN) {
+				u32 cmd = SLAVE_TRIGGER_CMD;
+
+				if (i2c_bus->mode == DMA_MODE) {
+					cmd |= AST2600_I2CS_RX_DMA_EN;
+					writel(i2c_bus->slave_dma_addr,
+						   i2c_bus->reg_base + AST2600_I2CS_RX_DMA);
+					writel(i2c_bus->slave_dma_addr,
+						   i2c_bus->reg_base + AST2600_I2CS_TX_DMA);
+					writel(AST2600_I2CS_SET_RX_DMA_LEN(I2C_SLAVE_MSG_BUF_SIZE),
+						   i2c_bus->reg_base + AST2600_I2CS_DMA_LEN);
+				} else if (i2c_bus->mode == BUFF_MODE) {
+					cmd = SLAVE_TRIGGER_CMD;
+				} else {
+					cmd &= ~AST2600_I2CS_PKT_MODE_EN;
+				}
+				writel(cmd, i2c_bus->reg_base + AST2600_I2CS_CMD_STS);
+			}
+#endif
+		}
+		ret = -ETIMEDOUT;
+	} else {
+		ret = i2c_bus->cmd_err;
+	}
+
+	dev_dbg(i2c_bus->dev, "bus%d-m: %d end\n", i2c_bus->adap.nr, i2c_bus->cmd_err);
+
+master_out:
+	if (i2c_bus->mode == DMA_MODE) {
+		kfree(i2c_bus->master_safe_buf);
+	    i2c_bus->master_safe_buf = NULL;
+	}
+
+	return ret;
+}
+
+static void ast2600_i2c_init(struct ast2600_i2c_bus *i2c_bus)
+{
+	struct platform_device *pdev = to_platform_device(i2c_bus->dev);
+	u32 fun_ctrl = AST2600_I2CC_BUS_AUTO_RELEASE | AST2600_I2CC_MASTER_EN;
+
+	/* I2C Reset */
+	writel(0, i2c_bus->reg_base + AST2600_I2CC_FUN_CTRL);
+
+	if (of_property_read_bool(pdev->dev.of_node, "multi-master"))
+		i2c_bus->multi_master = true;
+	else
+		fun_ctrl |= AST2600_I2CC_MULTI_MASTER_DIS;
+
+	/* Enable Master Mode */
+	writel(fun_ctrl, i2c_bus->reg_base + AST2600_I2CC_FUN_CTRL);
+	/* disable slave address */
+	writel(0, i2c_bus->reg_base + AST2600_I2CS_ADDR_CTRL);
+
+	/* Set AC Timing */
+	writel(ast2600_select_i2c_clock(i2c_bus), i2c_bus->reg_base + AST2600_I2CC_AC_TIMING);
+
+	/* Clear Interrupt */
+	writel(0xfffffff, i2c_bus->reg_base + AST2600_I2CM_ISR);
+
+#ifdef CONFIG_I2C_SLAVE
+	/* for memory buffer initial */
+	if (i2c_bus->mode == DMA_MODE) {
+		i2c_bus->slave_dma_buf = dma_alloc_coherent(i2c_bus->dev, I2C_SLAVE_MSG_BUF_SIZE,
+							    &i2c_bus->slave_dma_addr, GFP_KERNEL);
+		if (!i2c_bus->slave_dma_buf)
+			return;
+	}
+
+	writel(0xfffffff, i2c_bus->reg_base + AST2600_I2CS_ISR);
+
+	if (i2c_bus->mode == BYTE_MODE) {
+		writel(0xffff, i2c_bus->reg_base + AST2600_I2CS_IER);
+	} else {
+		/* Set interrupt generation of I2C slave controller */
+		writel(AST2600_I2CS_PKT_DONE, i2c_bus->reg_base + AST2600_I2CS_IER);
+	}
+#endif
+}
+
+#ifdef CONFIG_I2C_SLAVE
+static int ast2600_i2c_reg_slave(struct i2c_client *client)
+{
+	struct ast2600_i2c_bus *i2c_bus = i2c_get_adapdata(client->adapter);
+	u32 cmd = SLAVE_TRIGGER_CMD;
+
+	if (i2c_bus->slave)
+		return -EINVAL;
+
+	dev_dbg(i2c_bus->dev, "slave addr %x\n", client->addr);
+
+	writel(0, i2c_bus->reg_base + AST2600_I2CS_ADDR_CTRL);
+	writel(AST2600_I2CC_SLAVE_EN | readl(i2c_bus->reg_base + AST2600_I2CC_FUN_CTRL),
+	       i2c_bus->reg_base + AST2600_I2CC_FUN_CTRL);
+
+	/* trigger rx buffer */
+	if (i2c_bus->mode == DMA_MODE) {
+		cmd |= AST2600_I2CS_RX_DMA_EN;
+		writel(i2c_bus->slave_dma_addr, i2c_bus->reg_base + AST2600_I2CS_RX_DMA);
+		writel(i2c_bus->slave_dma_addr, i2c_bus->reg_base + AST2600_I2CS_TX_DMA);
+		writel(AST2600_I2CS_SET_RX_DMA_LEN(I2C_SLAVE_MSG_BUF_SIZE),
+		       i2c_bus->reg_base + AST2600_I2CS_DMA_LEN);
+	} else if (i2c_bus->mode == BUFF_MODE) {
+		cmd = SLAVE_TRIGGER_CMD;
+	} else {
+		cmd &= ~AST2600_I2CS_PKT_MODE_EN;
+	}
+
+	writel(cmd, i2c_bus->reg_base + AST2600_I2CS_CMD_STS);
+	i2c_bus->slave = client;
+	/* Set slave addr. */
+	writel(client->addr | AST2600_I2CS_ADDR1_ENABLE,
+			i2c_bus->reg_base + AST2600_I2CS_ADDR_CTRL);
+
+	return 0;
+}
+
+static int ast2600_i2c_unreg_slave(struct i2c_client *slave)
+{
+	struct ast2600_i2c_bus *i2c_bus = i2c_get_adapdata(slave->adapter);
+
+	WARN_ON(!i2c_bus->slave);
+
+	/* Turn off slave mode. */
+	writel(~AST2600_I2CC_SLAVE_EN & readl(i2c_bus->reg_base + AST2600_I2CC_FUN_CTRL),
+	       i2c_bus->reg_base + AST2600_I2CC_FUN_CTRL);
+	writel(readl(i2c_bus->reg_base + AST2600_I2CS_ADDR_CTRL) & ~AST2600_I2CS_ADDR1_MASK,
+	       i2c_bus->reg_base + AST2600_I2CS_ADDR_CTRL);
+
+	i2c_bus->slave = NULL;
+
+	return 0;
+}
+#endif
+
+static u32 ast2600_i2c_functionality(struct i2c_adapter *adap)
+{
+	return I2C_FUNC_I2C | I2C_FUNC_SMBUS_EMUL | I2C_FUNC_SMBUS_BLOCK_DATA;
+}
+
+static const struct i2c_algorithm i2c_ast2600_algorithm = {
+	.master_xfer = ast2600_i2c_master_xfer,
+#if IS_ENABLED(CONFIG_I2C_SLAVE)
+	.reg_slave = ast2600_i2c_reg_slave,
+	.unreg_slave = ast2600_i2c_unreg_slave,
+#endif
+	.functionality = ast2600_i2c_functionality,
+};
+
+static const struct of_device_id ast2600_i2c_bus_of_table[] = {
+	{
+		.compatible = "aspeed,ast2600-i2cv2",
+	},
+	{}
+};
+
+MODULE_DEVICE_TABLE(of, ast2600_i2c_bus_of_table);
+
+static int ast2600_i2c_probe(struct platform_device *pdev)
+{
+	struct device_node *np = pdev->dev.of_node;
+	struct device *dev = &pdev->dev;
+	struct ast2600_i2c_bus *i2c_bus;
+	struct resource *res;
+	u32 global_ctrl;
+	int ret = 0;
+
+	i2c_bus = devm_kzalloc(dev, sizeof(*i2c_bus), GFP_KERNEL);
+	if (!i2c_bus)
+		return -ENOMEM;
+
+	i2c_bus->reg_base = devm_platform_ioremap_resource(pdev, 0);
+	if (IS_ERR(i2c_bus->reg_base))
+		return PTR_ERR(i2c_bus->reg_base);
+
+	i2c_bus->rst = devm_reset_control_get_shared(dev, NULL);
+	if (IS_ERR(i2c_bus->rst))
+		return dev_err_probe(dev, PTR_ERR(i2c_bus->rst), "Missing reset ctrl\n");
+
+	reset_control_deassert(i2c_bus->rst);
+
+	i2c_bus->global_regs = syscon_regmap_lookup_by_phandle(np, "aspeed,global-regs");
+	if (IS_ERR(i2c_bus->global_regs))
+		return PTR_ERR(i2c_bus->global_regs);
+
+	regmap_read(i2c_bus->global_regs, AST2600_I2CG_CTRL, &global_ctrl);
+	if ((global_ctrl & AST2600_GLOBAL_INIT) != AST2600_GLOBAL_INIT) {
+		regmap_write(i2c_bus->global_regs, AST2600_I2CG_CTRL, AST2600_GLOBAL_INIT);
+		regmap_write(i2c_bus->global_regs, AST2600_I2CG_CLK_DIV_CTRL, I2CCG_DIV_CTRL);
+	}
+
+	i2c_bus->slave_operate = 0;
+	i2c_bus->dev = dev;
+	i2c_bus->mode = BUFF_MODE;
+
+	if (of_property_read_bool(pdev->dev.of_node, "aspeed,enable-dma"))
+		i2c_bus->mode = DMA_MODE;
+
+	if (i2c_bus->mode == BUFF_MODE) {
+		res = platform_get_resource(pdev, IORESOURCE_MEM, 1);
+		if (res && resource_size(res) >= 2) {
+			i2c_bus->buf_base = devm_ioremap_resource(dev, res);
+
+			if (!IS_ERR_OR_NULL(i2c_bus->buf_base))
+				i2c_bus->buf_size = resource_size(res)/2;
+		} else
+			i2c_bus->mode = BYTE_MODE;
+	}
+
+	/* i2c timeout counter: use base clk4 1Mhz,
+	 * per unit: 1/(1000/4096) = 4096us
+	 */
+	ret = of_property_read_u32(dev->of_node,
+							"i2c-scl-clk-low-timeout-us",
+							&i2c_bus->timeout);
+	if (ret < 0)
+		i2c_bus->timeout = 0;
+	else
+		i2c_bus->timeout /= 4096;
+
+	init_completion(&i2c_bus->cmd_complete);
+
+	i2c_bus->irq = platform_get_irq(pdev, 0);
+	if (i2c_bus->irq < 0)
+		return i2c_bus->irq;
+
+	platform_set_drvdata(pdev, i2c_bus);
+
+	i2c_bus->clk = devm_clk_get(i2c_bus->dev, NULL);
+	if (IS_ERR(i2c_bus->clk))
+		return dev_err_probe(i2c_bus->dev, PTR_ERR(i2c_bus->clk), "Can't get clock\n");
+
+	i2c_bus->apb_clk = clk_get_rate(i2c_bus->clk);
+
+	ret = of_property_read_u32(dev->of_node, "clock-frequency", &i2c_bus->bus_frequency);
+	if (ret < 0) {
+		dev_warn(dev, "Could not read clock-frequency property\n");
+		i2c_bus->bus_frequency = 100000;
+	}
+
+	/* Initialize the I2C adapter */
+	i2c_bus->adap.owner = THIS_MODULE;
+	i2c_bus->adap.algo = &i2c_ast2600_algorithm;
+	i2c_bus->adap.retries = 0;
+	i2c_bus->adap.dev.parent = i2c_bus->dev;
+	i2c_bus->adap.dev.of_node = dev->of_node;
+	i2c_bus->adap.algo_data = i2c_bus;
+	strscpy(i2c_bus->adap.name, pdev->name, sizeof(i2c_bus->adap.name));
+	i2c_set_adapdata(&i2c_bus->adap, i2c_bus);
+
+	ast2600_i2c_init(i2c_bus);
+
+	ret = devm_request_irq(dev, i2c_bus->irq, ast2600_i2c_bus_irq, 0,
+			       dev_name(dev), i2c_bus);
+	if (ret < 0)
+		return dev_err_probe(dev, ret, "Unable to request irq %d\n", i2c_bus->irq);
+
+	if (of_property_read_bool(dev->of_node, "smbus-alert")) {
+		i2c_bus->alert_enable = 1;
+		i2c_bus->ara = i2c_new_smbus_alert_device(&i2c_bus->adap, &i2c_bus->alert_data);
+		if (!i2c_bus->ara)
+			dev_warn(dev, "Failed to register ARA client\n");
+
+		writel(AST2600_I2CM_PKT_DONE | AST2600_I2CM_BUS_RECOVER | AST2600_I2CM_SMBUS_ALT,
+		       i2c_bus->reg_base + AST2600_I2CM_IER);
+	} else {
+		i2c_bus->alert_enable = 0;
+		/* Set interrupt generation of I2C master controller */
+		writel(AST2600_I2CM_PKT_DONE | AST2600_I2CM_BUS_RECOVER,
+				i2c_bus->reg_base + AST2600_I2CM_IER);
+	}
+
+	ret = i2c_add_adapter(&i2c_bus->adap);
+	if (ret)
+		return ret;
+
+	dev_info(dev, "%s [%d]: adapter [%d khz] mode [%d]\n",
+		 dev->of_node->name, i2c_bus->adap.nr, i2c_bus->bus_frequency / 1000,
+		 i2c_bus->mode);
+
+	return 0;
+}
+
+static int ast2600_i2c_remove(struct platform_device *pdev)
+{
+	struct ast2600_i2c_bus *i2c_bus = platform_get_drvdata(pdev);
+
+	/* Disable everything. */
+	writel(0, i2c_bus->reg_base + AST2600_I2CC_FUN_CTRL);
+	writel(0, i2c_bus->reg_base + AST2600_I2CM_IER);
+
+	i2c_del_adapter(&i2c_bus->adap);
+	devm_free_irq(&pdev->dev, i2c_bus->irq, i2c_bus);
+
+#ifdef CONFIG_I2C_SLAVE
+	/* for memory buffer initial */
+	if (i2c_bus->mode == DMA_MODE)
+		dma_free_coherent(i2c_bus->dev, I2C_SLAVE_MSG_BUF_SIZE,
+				i2c_bus->slave_dma_buf, i2c_bus->slave_dma_addr);
+#endif
+
+	return 0;
+}
+
+static struct platform_driver ast2600_i2c_bus_driver = {
+	.probe = ast2600_i2c_probe,
+	.remove = ast2600_i2c_remove,
+	.driver = {
+		.name = KBUILD_MODNAME,
+		.of_match_table = ast2600_i2c_bus_of_table,
+	},
+};
+module_platform_driver(ast2600_i2c_bus_driver);
+
+MODULE_AUTHOR("Ryan Chen <ryan_chen@xxxxxxxxxxxxxx>");
+MODULE_DESCRIPTION("ASPEED AST2600 I2C Controller Driver");
+MODULE_LICENSE("GPL");
-- 
2.34.1




[Index of Archives]     [Linux GPIO]     [Linux SPI]     [Linux Hardward Monitoring]     [LM Sensors]     [Linux USB Devel]     [Linux Media]     [Video for Linux]     [Linux Audio Users]     [Yosemite News]     [Linux Kernel]     [Linux SCSI]

  Powered by Linux