On Wed, 18 Jan 2023 at 00:52, <nick.hawkins@xxxxxxx> wrote:
>
> From: Nick Hawkins <nick.hawkins@xxxxxxx>
>
> The GXP SoC supports 10 I2C engines. Each I2C engine is completely
> independent and can function both as an I2C master and I2C slave. The
> I2C master can operate in a multi master environment. The engines support
> a scalable speed from 8kHZ to 1.5 Mhz.
>
> Signed-off-by: Nick Hawkins <nick.hawkins@xxxxxxx>
Looks pretty good to me. I have some minor review comments below.
Reviewed-by: Joel Stanley <joel@xxxxxxxxx>
>
> ---
>
> v2:
> *Removed rogue tab in structure
> *Removed use of __iomem base local variables as it was unnecessary
> *Switched #if IS_ENABLED() -> if (IS_ENABLED()) inside functions
> *Removed use of pr_* functions
> *Removed informational prints in register and unregister functions
> *Removed print from interrupt handler
> *No informational prints in probe function
> *Switched dev_err for dev_err_probe in probe function
> *Use respective helper for mapping the resource to __iomem
> ---
> drivers/i2c/busses/Kconfig | 7 +
> drivers/i2c/busses/Makefile | 1 +
> drivers/i2c/busses/i2c-gxp.c | 609 +++++++++++++++++++++++++++++++++++
> 3 files changed, 617 insertions(+)
> create mode 100644 drivers/i2c/busses/i2c-gxp.c
>
> diff --git a/drivers/i2c/busses/Kconfig b/drivers/i2c/busses/Kconfig
> index e50f9603d189..8b3951e0ca5c 100644
> --- a/drivers/i2c/busses/Kconfig
> +++ b/drivers/i2c/busses/Kconfig
> @@ -1457,4 +1457,11 @@ config I2C_VIRTIO
> This driver can also be built as a module. If so, the module
> will be called i2c-virtio.
>
> +config I2C_GXP
> + tristate "GXP I2C Interface"
> + depends on ARCH_HPE_GXP || COMPILE_TEST
> + help
> + This enables support for GXP I2C interface. The I2C engines can be
> + either I2C master or I2C slaves.
> +
> endmenu
> diff --git a/drivers/i2c/busses/Makefile b/drivers/i2c/busses/Makefile
> index e73cdb1d2b5a..dcc96eab6d68 100644
> --- a/drivers/i2c/busses/Makefile
> +++ b/drivers/i2c/busses/Makefile
> @@ -127,6 +127,7 @@ obj-$(CONFIG_I2C_THUNDERX) += i2c-thunderx.o
> obj-$(CONFIG_I2C_XILINX) += i2c-xiic.o
> obj-$(CONFIG_I2C_XLP9XX) += i2c-xlp9xx.o
> obj-$(CONFIG_I2C_RCAR) += i2c-rcar.o
> +obj-$(CONFIG_I2C_GXP) += i2c-gxp.o
>
> # External I2C/SMBus adapter drivers
> obj-$(CONFIG_I2C_DIOLAN_U2C) += i2c-diolan-u2c.o
> diff --git a/drivers/i2c/busses/i2c-gxp.c b/drivers/i2c/busses/i2c-gxp.c
> new file mode 100644
> index 000000000000..bd41858a3149
> --- /dev/null
> +++ b/drivers/i2c/busses/i2c-gxp.c
> @@ -0,0 +1,609 @@
> +// SPDX-License-Identifier: GPL-2.0-only
> +/* Copyright (C) 2022 Hewlett-Packard Enterprise Development Company, L.P. */
> +
> +#include <linux/err.h>
> +#include <linux/io.h>
> +#include <linux/i2c.h>
> +#include <linux/module.h>
> +#include <linux/of_device.h>
> +#include <linux/regmap.h>
> +#include <linux/mfd/syscon.h>
> +
> +#define GXP_MAX_I2C_ENGINE 10
> +static const char * const gxp_i2c_name[] = {
> + "gxp-i2c0", "gxp-i2c1", "gxp-i2c2", "gxp-i2c3",
> + "gxp-i2c4", "gxp-i2c5", "gxp-i2c6", "gxp-i2c7",
> + "gxp-i2c8", "gxp-i2c9" };
> +
> +/* Default value */
> +#define GXP_I2C_BIT_RATE 100000 /* 100kHz */
> +
> +/* GXP I2C Global interrupt status/enable register*/
> +#define GXP_I2CINTSTAT 0x00
> +#define GXP_I2CINTEN 0x04
> +
> +/* GXP I2C registers */
> +#define GXP_I2CSTAT 0x00
> +#define MASK_STOP_EVENT 0x20
> +#define MASK_ACK 0x08
> +#define MASK_RW 0x04
> +#define GXP_I2CEVTERR 0x01
> +#define MASK_SLAVE_CMD_EVENT 0x01
> +#define MASK_SLAVE_DATA_EVENT 0x02
> +#define MASK_MASTER_EVENT 0x10
> +#define GXP_I2CSNPDAT 0x02
> +#define GXP_I2CMCMD 0x04
> +#define GXP_I2CSCMD 0x06
> +#define GXP_I2CSNPAA 0x09
> +#define GXP_I2CADVFEAT 0x0A
> +#define GXP_I2COWNADR 0x0B
> +#define GXP_I2CFREQDIV 0x0C
> +#define GXP_I2CFLTFAIR 0x0D
> +#define GXP_I2CTMOEDG 0x0E
> +#define GXP_I2CCYCTIM 0x0F
> +
> +static bool i2c_global_init_done;
> +
> +enum {
> + GXP_I2C_IDLE = 0,
> + GXP_I2C_ADDR_PHASE,
> + GXP_I2C_RDATA_PHASE,
> + GXP_I2C_WDATA_PHASE,
> + GXP_I2C_ADDR_NACK,
> + GXP_I2C_DATA_NACK,
> + GXP_I2C_ERROR,
> + GXP_I2C_COMP
> +};
> +
> +struct gxp_i2c_drvdata {
> + struct device *dev;
> + void __iomem *base;
> + u32 bus_frequency;
> + int engine;
> + int irq;
> + struct completion completion;
> + struct i2c_adapter adapter;
> + struct i2c_msg *curr_msg;
> + int msgs_remaining;
> + int msgs_num;
> + u8 *buf;
> + size_t buf_remaining;
> + unsigned char state;
> + struct i2c_client *slave;
> + unsigned char stopped;
> +};
> +
> +static struct regmap *i2cg_map;
> +
> +static void gxp_i2c_start(struct gxp_i2c_drvdata *drvdata)
> +{
> + u16 value;
> +
> + drvdata->buf = drvdata->curr_msg->buf;
> + drvdata->buf_remaining = drvdata->curr_msg->len;
> +
> + /* Note: Address in struct i2c_msg is 7 bits */
> + value = drvdata->curr_msg->addr << 9;
> +
> + if (drvdata->curr_msg->flags & I2C_M_RD) {
> + /* Read */
> + value |= 0x05;
> + } else {
> + /* Write */
> + value |= 0x01;
> + }
> +
> + drvdata->state = GXP_I2C_ADDR_PHASE;
> + writew(value, drvdata->base + GXP_I2CMCMD);
> +}
> +
> +static int gxp_i2c_master_xfer(struct i2c_adapter *adapter,
> + struct i2c_msg *msgs, int num)
> +{
> + int ret;
> + struct gxp_i2c_drvdata *drvdata = i2c_get_adapdata(adapter);
> + unsigned long time_left;
> +
> + drvdata->msgs_remaining = num;
> + drvdata->curr_msg = msgs;
> + drvdata->msgs_num = num;
> + reinit_completion(&drvdata->completion);
> +
> + gxp_i2c_start(drvdata);
> +
> + time_left = wait_for_completion_timeout(&drvdata->completion,
> + adapter->timeout);
> + ret = num - drvdata->msgs_remaining;
> + if (time_left == 0) {
> + switch (drvdata->state) {
> + case GXP_I2C_WDATA_PHASE:
> + dev_err(drvdata->dev,
> + "gxp_i2c_start:write Data phase timeout at msg[%d]\n",
> + ret);
> + break;
> + case GXP_I2C_RDATA_PHASE:
> + dev_err(drvdata->dev,
> + "gxp_i2c_start:read Data phase timeout at msg[%d]\n",
> + ret);
> + break;
> + case GXP_I2C_ADDR_PHASE:
> + dev_err(drvdata->dev,
> + "gxp_i2c_start:Addr phase timeout\n");
> + break;
> + default:
> + dev_err(drvdata->dev,
> + "gxp_i2c_start:i2c transfer timeout state=%d\n",
> + drvdata->state);
> + break;
> + }
> + return -ETIMEDOUT;
> + }
> +
> + if (drvdata->state == GXP_I2C_ADDR_NACK) {
> + dev_err(drvdata->dev,
> + "gxp_i2c_start:No ACK for address phase\n");
> + return -EIO;
> + } else if (drvdata->state == GXP_I2C_DATA_NACK) {
> + dev_err(drvdata->dev, "gxp_i2c_start:No ACK for data phase\n");
> + return -EIO;
> + }
> +
> + return ret;
> +}
> +
> +static u32 gxp_i2c_func(struct i2c_adapter *adap)
> +{
> + if (IS_ENABLED(CONFIG_I2C_SLAVE))
> + return I2C_FUNC_I2C | I2C_FUNC_SMBUS_EMUL | I2C_FUNC_SLAVE;
> +
> + return I2C_FUNC_I2C | I2C_FUNC_SMBUS_EMUL;
> +}
> +
> +#if IS_ENABLED(CONFIG_I2C_SLAVE)
> +static int gxp_i2c_reg_slave(struct i2c_client *slave)
> +{
> + struct gxp_i2c_drvdata *drvdata = i2c_get_adapdata(slave->adapter);
> +
> + if (drvdata->slave)
> + return -EBUSY;
> +
> + if (slave->flags & I2C_CLIENT_TEN)
> + return -EAFNOSUPPORT;
> +
> + drvdata->slave = slave;
> +
> + writeb(slave->addr << 1, drvdata->base + GXP_I2COWNADR);
> + writeb(0x69, drvdata->base + GXP_I2CSCMD);
> +
> + return 0;
> +}
> +
> +static int gxp_i2c_unreg_slave(struct i2c_client *slave)
> +{
> + struct gxp_i2c_drvdata *drvdata = i2c_get_adapdata(slave->adapter);
> +
> + WARN_ON(!drvdata->slave);
> +
> + writeb(0x00, drvdata->base + GXP_I2COWNADR);
> + writeb(0xF0, drvdata->base + GXP_I2CSCMD);
> +
> + drvdata->slave = NULL;
> +
> + return 0;
> +}
> +#endif
> +
> +static const struct i2c_algorithm gxp_i2c_algo = {
> + .master_xfer = gxp_i2c_master_xfer,
> + .functionality = gxp_i2c_func,
> +#if IS_ENABLED(CONFIG_I2C_SLAVE)
> + .reg_slave = gxp_i2c_reg_slave,
> + .unreg_slave = gxp_i2c_unreg_slave,
> +#endif
> +};
> +
> +static void gxp_i2c_stop(struct gxp_i2c_drvdata *drvdata)
> +{
> + /* Clear event and send stop */
> + writeb(0x82, drvdata->base + GXP_I2CMCMD);
> +
> + complete(&drvdata->completion);
> +}
> +
> +static void gxp_i2c_restart(struct gxp_i2c_drvdata *drvdata)
> +{
> + u16 value;
> +
> + drvdata->buf = drvdata->curr_msg->buf;
> + drvdata->buf_remaining = drvdata->curr_msg->len;
> +
> + value = drvdata->curr_msg->addr << 9;
> +
> + if (drvdata->curr_msg->flags & I2C_M_RD) {
> + /* Read and clear master event */
> + value |= 0x85;
> + } else {
> + /* Write and clear master event */
> + value |= 0x81;
> + }
> +
> + drvdata->state = GXP_I2C_ADDR_PHASE;
> +
> + writew(value, drvdata->base + GXP_I2CMCMD);
> +}
> +
> +static void gxp_i2c_chk_addr_ack(struct gxp_i2c_drvdata *drvdata)
> +{
> + u16 value;
> +
> + value = readb(drvdata->base + GXP_I2CSTAT);
> + if (!(value & MASK_ACK)) {
> + /* Got no ack, stop */
> + drvdata->state = GXP_I2C_ADDR_NACK;
> + gxp_i2c_stop(drvdata);
> + return;
> + }
> +
> + if (drvdata->curr_msg->flags & I2C_M_RD) {
> + /* Start to read data from slave */
> + if (drvdata->buf_remaining == 0) {
> + /* No more data to read, stop */
> + drvdata->msgs_remaining--;
> + drvdata->state = GXP_I2C_COMP;
> + gxp_i2c_stop(drvdata);
> + return;
> + }
> + drvdata->state = GXP_I2C_RDATA_PHASE;
> +
> + if (drvdata->buf_remaining == 1) {
> + /* The last data, do not ack */
> + writeb(0x84, drvdata->base + GXP_I2CMCMD);
> + } else {
> + /* Read data and ack it */
> + writeb(0x8C, drvdata->base + GXP_I2CMCMD);
> + }
> + } else {
> + /* Start to write first data to slave */
> + if (drvdata->buf_remaining == 0) {
> + /* No more data to write, stop */
> + drvdata->msgs_remaining--;
> + drvdata->state = GXP_I2C_COMP;
> + gxp_i2c_stop(drvdata);
> + return;
> + }
> + value = *drvdata->buf;
> + value = value << 8;
> + /* Clear master event */
> + value |= 0x80;
> + drvdata->buf++;
> + drvdata->buf_remaining--;
> + drvdata->state = GXP_I2C_WDATA_PHASE;
> + writew(value, drvdata->base + GXP_I2CMCMD);
> + }
> +}
> +
> +static void gxp_i2c_ack_data(struct gxp_i2c_drvdata *drvdata)
> +{
> + u8 value;
> +
> + /* Store the data returned */
> + value = readb(drvdata->base + GXP_I2CSNPDAT);
> + *drvdata->buf = value;
> + drvdata->buf++;
> + drvdata->buf_remaining--;
> +
> + if (drvdata->buf_remaining == 0) {
> + /* No more data, this message is completed. */
> + drvdata->msgs_remaining--;
> +
> + if (drvdata->msgs_remaining == 0) {
> + /* No more messages, stop */
> + drvdata->state = GXP_I2C_COMP;
> + gxp_i2c_stop(drvdata);
> + return;
> + }
> + /* Move to next message and start transfer */
> + drvdata->curr_msg++;
> + gxp_i2c_restart(drvdata);
> + return;
> + }
> +
> + /* Ack the slave to make it send next byte */
> + drvdata->state = GXP_I2C_RDATA_PHASE;
> + if (drvdata->buf_remaining == 1) {
> + /* The last data, do not ack */
> + writeb(0x84, drvdata->base + GXP_I2CMCMD);
> + } else {
> + /* Read data and ack it */
> + writeb(0x8C, drvdata->base + GXP_I2CMCMD);
> + }
> +}
> +
> +static void gxp_i2c_chk_data_ack(struct gxp_i2c_drvdata *drvdata)
> +{
> + u16 value;
> +
> + value = readb(drvdata->base + GXP_I2CSTAT);
> + if (!(value & MASK_ACK)) {
> + /* Received No ack, stop */
> + drvdata->state = GXP_I2C_DATA_NACK;
> + gxp_i2c_stop(drvdata);
> + return;
> + }
> +
> + /* Got ack, check if there is more data to write */
> + if (drvdata->buf_remaining == 0) {
> + /* No more data, this message is completed */
> + drvdata->msgs_remaining--;
> +
> + if (drvdata->msgs_remaining == 0) {
> + /* No more messages, stop */
> + drvdata->state = GXP_I2C_COMP;
> + gxp_i2c_stop(drvdata);
> + return;
> + }
> + /* Move to next message and start transfer */
> + drvdata->curr_msg++;
> + gxp_i2c_restart(drvdata);
> + return;
> + }
> +
> + /* Write data to slave */
> + value = *drvdata->buf;
> + value = value << 8;
> +
> + /* Clear master event */
> + value |= 0x80;
> + drvdata->buf++;
> + drvdata->buf_remaining--;
> + drvdata->state = GXP_I2C_WDATA_PHASE;
> + writew(value, drvdata->base + GXP_I2CMCMD);
> +}
> +
> +#if IS_ENABLED(CONFIG_I2C_SLAVE)
> +static bool gxp_i2c_slave_irq_handler(struct gxp_i2c_drvdata *drvdata)
> +{
> + u16 value;
> + u8 buf;
> + int ret;
> +
> + value = readb(drvdata->base + GXP_I2CEVTERR);
If you're reading value with readb, it could be a u8 too?
> +
> + /* Received start or stop event */
> + if (value & MASK_SLAVE_CMD_EVENT) {
> + value = readb(drvdata->base + GXP_I2CSTAT);
> + /* Master sent stop */
> + if (value & MASK_STOP_EVENT) {
> + if (drvdata->stopped == 0)
> + i2c_slave_event(drvdata->slave, I2C_SLAVE_STOP, &buf);
> + writeb(0x69, drvdata->base + GXP_I2CSCMD);
> + drvdata->stopped = 1;
> + } else {
> + /* Master sent start and wants to read */
> + drvdata->stopped = 0;
> + if (value & MASK_RW) {
> + i2c_slave_event(drvdata->slave,
> + I2C_SLAVE_READ_REQUESTED, &buf);
> + value = buf << 8 | 0x61;
> + writew(value, drvdata->base + GXP_I2CSCMD);
> + } else {
> + /* Master wants to write to us */
> + ret = i2c_slave_event(drvdata->slave,
> + I2C_SLAVE_WRITE_REQUESTED, &buf);
> + if (!ret) {
> + /* Ack next byte from master */
> + writeb(0x69, drvdata->base + GXP_I2CSCMD);
> + } else {
> + /* Nack next byte from master */
> + writeb(0x61, drvdata->base + GXP_I2CSCMD);
> + }
> + }
> + }
> + } else if (value & MASK_SLAVE_DATA_EVENT) {
> + value = readb(drvdata->base + GXP_I2CSTAT);
> + /* Master wants to read */
> + if (value & MASK_RW) {
> + /* Master wants another byte */
> + if (value & MASK_ACK) {
> + i2c_slave_event(drvdata->slave,
> + I2C_SLAVE_READ_PROCESSED, &buf);
> + value = buf << 8 | 0x61;
> + writew(value, drvdata->base + GXP_I2CSCMD);
> + } else {
> + /* No more bytes needed */
> + writew(0x69, drvdata->base + GXP_I2CSCMD);
> + }
> + } else {
> + /* Master wants to write to us */
> + value = readb(drvdata->base + GXP_I2CSNPDAT);
> + buf = (uint8_t)value;
> + ret = i2c_slave_event(drvdata->slave,
> + I2C_SLAVE_WRITE_RECEIVED, &buf);
> + if (!ret) {
> + /* Ack next byte from master */
> + writeb(0x69, drvdata->base + GXP_I2CSCMD);
> + } else {
> + /* Nack next byte from master */
> + writeb(0x61, drvdata->base + GXP_I2CSCMD);
> + }
> + }
> + } else {
> + return false;
> + }
> +
> + return true;
> +}
> +#endif
> +
> +static irqreturn_t gxp_i2c_irq_handler(int irq, void *_drvdata)
> +{
> + struct gxp_i2c_drvdata *drvdata = (struct gxp_i2c_drvdata *)_drvdata;
> + u32 value;
> +
> + regmap_read(i2cg_map, GXP_I2CINTSTAT, &value);
> + if (!(value & (1 << drvdata->engine)))
1U, or BIT(drvdata->engine).
This is checking that the interrupt is for an engine that is enabled
(or that is present)?
> + return IRQ_NONE;
> +
> + value = readb(drvdata->base + GXP_I2CEVTERR);
> +
> + /* Error */
> + if (value & ~(MASK_MASTER_EVENT | MASK_SLAVE_CMD_EVENT |
> + MASK_SLAVE_DATA_EVENT)) {
> + /* Clear all events */
> + writeb(0x00, drvdata->base + GXP_I2CEVTERR);
> + drvdata->state = GXP_I2C_ERROR;
> + gxp_i2c_stop(drvdata);
> + return IRQ_HANDLED;
> + }
> +
> + if (IS_ENABLED(CONFIG_I2C_SLAVE)) {
> + /* Slave mode */
> + if (value & (MASK_SLAVE_CMD_EVENT | MASK_SLAVE_DATA_EVENT)) {
> + if (gxp_i2c_slave_irq_handler(drvdata))
> + return IRQ_HANDLED;
> + return IRQ_NONE;
> + }
> + }
> +
> + /* Master mode */
> + switch (drvdata->state) {
> + case GXP_I2C_ADDR_PHASE:
> + gxp_i2c_chk_addr_ack(drvdata);
> + break;
> +
> + case GXP_I2C_RDATA_PHASE:
> + gxp_i2c_ack_data(drvdata);
> + break;
> +
> + case GXP_I2C_WDATA_PHASE:
> + gxp_i2c_chk_data_ack(drvdata);
> + break;
> + }
> +
> + return IRQ_HANDLED;
> +}
> +
> +static void gxp_i2c_init(struct gxp_i2c_drvdata *drvdata)
> +{
> + drvdata->state = GXP_I2C_IDLE;
> + writeb(2000000 / drvdata->bus_frequency,
> + drvdata->base + GXP_I2CFREQDIV);
> + writeb(0x32, drvdata->base + GXP_I2CFLTFAIR);
> + writeb(0x0a, drvdata->base + GXP_I2CTMOEDG);
> + writeb(0x00, drvdata->base + GXP_I2CCYCTIM);
> + writeb(0x00, drvdata->base + GXP_I2CSNPAA);
> + writeb(0x00, drvdata->base + GXP_I2CADVFEAT);
> + writeb(0xF0, drvdata->base + GXP_I2CSCMD);
> + writeb(0x80, drvdata->base + GXP_I2CMCMD);
> + writeb(0x00, drvdata->base + GXP_I2CEVTERR);
> + writeb(0x00, drvdata->base + GXP_I2COWNADR);
> +}
> +
> +static int gxp_i2c_probe(struct platform_device *pdev)
> +{
> + struct gxp_i2c_drvdata *drvdata;
> + int rc;
> + struct resource *res;
> + struct i2c_adapter *adapter;
> +
> + if (!i2c_global_init_done) {
> + i2cg_map = syscon_regmap_lookup_by_phandle(pdev->dev.of_node,
> + "hpe,sysreg");
> + if (IS_ERR(i2cg_map)) {
> + return dev_err_probe(&pdev->dev, IS_ERR(i2cg_map),
> + "failed to map i2cg_handle\n");
> + }
> +
> + /* Disable interrupt */
> + regmap_update_bits(i2cg_map, GXP_I2CINTEN, 0x00000FFF, 0);
> + i2c_global_init_done = true;
> + }
> +
> + drvdata = devm_kzalloc(&pdev->dev, sizeof(*drvdata),
> + GFP_KERNEL);
> + if (!drvdata)
> + return -ENOMEM;
> +
> + platform_set_drvdata(pdev, drvdata);
> + drvdata->dev = &pdev->dev;
> + init_completion(&drvdata->completion);
> +
> + drvdata->base = devm_platform_ioremap_resource(pdev, 0);
> + if (IS_ERR(drvdata->base))
> + return PTR_ERR(drvdata->base);
> +
> + /* Use physical memory address to determine which I2C engine this is. */
> + res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
> + drvdata->engine = (res->start & 0xf00) >> 8;
As I understand it res->start will correspond to drvdata->base, so you
can use that instead?
> +
> + if (drvdata->engine >= GXP_MAX_I2C_ENGINE) {
> + return dev_err_probe(&pdev->dev, -EINVAL, "i2c engine% is unsupported\n",
> + drvdata->engine);
> + }
> +
> + rc = platform_get_irq(pdev, 0);
> + if (rc < 0)
> + return dev_err_probe(&pdev->dev, rc, "unable to obtain IRQ number\n");
platform_get_irq does dev_err_probe for you, just return rc.
> +
> + drvdata->irq = rc;
> + rc = devm_request_irq(&pdev->dev, drvdata->irq, gxp_i2c_irq_handler,
> + IRQF_SHARED, gxp_i2c_name[drvdata->engine], drvdata);
> + if (rc < 0)
> + return dev_err_probe(&pdev->dev, rc, "irq request failed\n");
> +
> + rc = of_property_read_u32(pdev->dev.of_node,
> + "clock-frequency", &drvdata->bus_frequency);
The i2c core has helpers here, see if i2c_parse_fw_timings does what you want.
> + if (rc < 0)
> + drvdata->bus_frequency = GXP_I2C_BIT_RATE;
> +
> + gxp_i2c_init(drvdata);
> +
> + /* Enable interrupt */
> + regmap_update_bits(i2cg_map, GXP_I2CINTEN, BIT(drvdata->engine),
> + BIT(drvdata->engine));
> +
> + adapter = &drvdata->adapter;
> + i2c_set_adapdata(adapter, drvdata);
> +
> + adapter->owner = THIS_MODULE;
> + adapter->class = I2C_CLASS_DEPRECATED;
I don't think this is needed for new drivers?
> + strscpy(adapter->name, "HPE GXP I2C adapter", sizeof(adapter->name));
> + adapter->algo = &gxp_i2c_algo;
> + adapter->dev.parent = &pdev->dev;
> + adapter->dev.of_node = pdev->dev.of_node;
> +
> + rc = i2c_add_adapter(adapter);
> + if (rc)
> + return dev_err_probe(&pdev->dev, rc, "i2c add adapter failed\n");
> +
> + return 0;
> +}
> +
> +static int gxp_i2c_remove(struct platform_device *pdev)
> +{
> + struct gxp_i2c_drvdata *drvdata = platform_get_drvdata(pdev);
> +
Do you want to disable the IRQs here?
> + i2c_del_adapter(&drvdata->adapter);
> +
> + return 0;
> +}
> +
> +static const struct of_device_id gxp_i2c_of_match[] = {
> + { .compatible = "hpe,gxp-i2c" },
> + {},
> +};
> +MODULE_DEVICE_TABLE(of, gxp_i2c_of_match);
> +
> +static struct platform_driver gxp_i2c_driver = {
> + .probe = gxp_i2c_probe,
> + .remove = gxp_i2c_remove,
> + .driver = {
> + .name = "gxp-i2c",
> + .of_match_table = gxp_i2c_of_match,
> + },
> +};
> +module_platform_driver(gxp_i2c_driver);
> +
> +MODULE_AUTHOR("Nick Hawkins <nick.hawkins@xxxxxxx>");
> +MODULE_DESCRIPTION("HPE GXP I2C bus driver");
> +MODULE_LICENSE("GPL");
> --
> 2.17.1
>
